162173 Ryugu, the target of Hayabusa2, has a round shape with an equatorial ridge, which is known as a spinning top-shape. A strong centrifugal force is a likely contributor to Ryugu's top-shaped features. Observations by Optical Navigation Camera onboard Hayabusa2 show a unique longitudinal variation in geomorphology; the western side of this asteroid, later called the western bulge, has a smooth surface and a sharp equatorial ridge, compared to the other side. Here, we propose a structural deformation process that generated the western bulge. Applying the mission-derived shape model, we employ a finite element model technique to analyze the locations that experience structural failure within the present shape. Assuming that materials are uniformly distributed, our model shows the longitudinal variation in structurally failed regions when the spin period is shorter than ~3.75 h. Ryugu is structurally intact in the subsurface region of the western bulge while other regions are sensitive to structural failure. We infer that this variation is indicative of the deformation process that occurred in the past, and the western bulge is more relaxed structurally than the other region. Our analysis also shows that this deformation process might occur at a spin period between ~3.5 h and ~3.0 h, providing the cohesive strength ranging between ~4 Pa and ~10 Pa.

The Optical Navigation Camera (ONC-T, ONC-W1, ONC-W2) onboard Hayabusa2 are also being used for scientific observations of the mission target, C-complex asteroid 162173 Ryugu. Science observations and analyses require rigorous instrument calibration. In order to meet this requirement, we have conducted extensive inflight observations during the 3.5 years of cruise after the launch of Hayabusa2 on 3 December 2014. In addition to the first inflight calibrations by Suzuki et al. (2018), we conducted an additional series of calibrations, including read-out smear, electronic-interference noise, bias, dark current, hot pixels, sensitivity, linearity, flat-field, and stray light measurements for the ONC. Moreover, the calibrations, especially flat-fields and sensitivities, of ONC-W1 and -W2 are updated for the analysis of the low-altitude (i.e., high-resolution) observations, such as the gravity measurement, touchdowns, and the descents for MASCOT and MINERVA-II payload releases. The radiometric calibration for ONC-T is also updated in this study based on star and Moon observations. Our updated inflight sensitivity measurements suggest the accuracy of the absolute radiometric calibration contains less than 1.8% error for the ul-, b-, v-, Na-, w-, and x-bands based on star calibration observations and ~5% for the p-band based on lunar calibration observations. The radiance spectra of the Moon, Jupiter, and Saturn from the ONC-T show good agreement with the spacecraft-based observations of the Moon from SP/SELENE and WAC/LROC and with ground-based telescopic observations for Jupiter and Saturn.

A model for the asteroid resurfacing by regolith convection is built to estimate its timescale. In the model, regolith convection is driven by the impact-induced global seismic shaking. The model consists of three steps: (i) intermittent impact of meteoroids, (ii) impact-induced global vibration (seismic shaking), and (iii) vibration-induced regolith convection. In order to assess the feasibility of the resurfacing process driven by regolith convection, we estimate the resurfacing timescale as a function of the size of a target asteroid. In the estimate, a set of parameter values is assumed on the basis of previous works. However, some of them (e.g., seismic quality factor $Q$, seismic efficiency $\eta$, and seismic frequency $f$) are very uncertain. Although these parameter values might depend on asteroid size, we employ the standard values to estimate the representative behavior. To clarify the parameter dependences, we develop an approximated scaling form for the resurfacing timescale. According to the estimated result, we find that the regolith-convection-based resurfacing timescale is shorter than the mean collisional lifetime in most of the parameter uncertainty ranges. These parameter ranges are within those reported by previous works for small asteroids. This means that the regolith convection can be a possible mechanism for the asteroid resurfacing process.