The Galactic magnetar SGR1935+2154 has been reported to produce the first known example of a bright millisecond duration radio burst (FRB 200428) similar to the cosmological population of fast radio bursts (FRBs), bolstering the association of FRBs to active magnetars. The detection of a coincident bright X-ray burst has revealed the first observed multi-wavelength counterpart of a FRB. However, the search for similar emission at optical wavelengths has been hampered by the high inferred extinction on the line of sight. Here, we present results from the first search for second-timescale emission from the source at near-infrared wavelengths using the Palomar Gattini-IR observing system in J-band, made possible by a recently implemented detector read-out mode that allowed for short exposure times of 0.84 s with 99.9% observing efficiency. With a total observing time of 12 hours (47728 images) on source, we place median $3\,\sigma$ limits on the second-timescale emission of $< 20$ mJy (13.1 AB mag). We present non-detection limits from epochs of four simultaneous X-ray bursts detected by the Insight-{\it HXMT} and {\it NuSTAR} telescopes during our observing campaign. The limits translate to an extinction corrected fluence limit of $< 125$ Jy ms for an estimated extinction of $A_J = 2.0$ mag. These limits provide the most stringent constraints to date on the fluence of flares at frequencies of $\sim 10^{14}$ Hz, and constrain the ratio of the near-infrared (NIR) fluence to that of coincident X-ray bursts to $R_{\rm NIR} < 2.5 \times 10^{-2}$. Our observations were sensitive enough to easily detect a near-infrared counterpart of FRB 200428 if the NIR emission falls on the same power law as that observed across its radio to X-ray spectrum. The non-detection of NIR emission around the coincident X-ray bursts constrains the fluence index of the brightest burst to be steeper than $0.35$.

(Abridged) Palomar Gattini-IR is a new wide-field, near-infrared robotic time domain survey operating at Palomar Observatory. Using a 30 cm telescope mounted with a H2RG detector, Gattini-IR achieves a field of view of 25 sq. deg. with a pixel scale of 8.7" in J-band. Here, we describe the system design, survey operations, data processing system and on-sky performance of Palomar Gattini-IR. As a part of the nominal survey, Gattini-IR scans $\approx 7500$ square degrees of the sky every night to a median 5$\sigma$ depth of $15.7$ AB mag outside the Galactic plane. The survey covers $\approx 15000$ square degrees of the sky visible from Palomar with a median cadence of 2 days. A real-time data processing system produces stacked science images from dithered raw images taken on sky, together with PSF-fit source catalogs and transient candidates identified from subtractions within a median delay of $\approx 4$ hours from the time of observation. The calibrated data products achieve an astrometric accuracy (RMS) of $\approx 0.7$" with respect to Gaia DR2 for sources with S/N $> 10$, and better than $\approx 0.35$" for sources brighter than $\approx 12$ Vega mag. The photometric accuracy (RMS) achieved in the PSF-fit source catalogs is better than $\approx 3$% for sources brighter than $\approx 12$ Vega mag, as calibrated against the 2MASS catalog. With a field of view $\approx 40\times$ larger than any other existing near infrared imaging instrument, Gattini-IR is probing the reddest and dustiest transients in the local universe such as dust obscured supernovae in nearby galaxies, novae behind large columns of extinction within the galaxy, reddened micro-lensing events in the Galactic plane and variability from cool and dust obscured stars. We present results from transients and variables identified since the start of the commissioning period.

The third observing run by LVC has brought the discovery of many compact binary coalescences. Following the detection of the first binary neutron star merger in this run (LIGO/Virgo S190425z), we performed a dedicated follow-up campaign with the Zwicky Transient Facility (ZTF) and Palomar Gattini-IR telescopes. The initial skymap of this single-detector gravitational wave (GW) trigger spanned most of the sky observable from Palomar Observatory. Covering 8000 deg$^2$ of the initial skymap over the next two nights, corresponding to 46\% integrated probability, ZTF system achieved a depth of $\approx$\,21 $m_\textrm{AB}$ in $g$- and $r$-bands. Palomar Gattini-IR covered 2200 square degrees in $J$-band to a depth of 15.5\,mag, including 32\% integrated probability based on the initial sky map. The revised skymap issued the following day reduced these numbers to 21\% for the Zwicky Transient Facility and 19\% for Palomar Gattini-IR. We narrowed 338,646 ZTF transient "alerts" over the first two nights of observations to 15 candidate counterparts. Two candidates, ZTF19aarykkb and ZTF19aarzaod, were particularly compelling given that their location, distance, and age were consistent with the GW event, and their early optical lightcurves were photometrically consistent with that of kilonovae. These two candidates were spectroscopically classified as young core-collapse supernovae. The remaining candidates were ruled-out as supernovae. Palomar Gattini-IR did not identify any viable candidates with multiple detections only after merger time. We demonstrate that even with single-detector GW events localized to thousands of square degrees, systematic kilonova discovery is feasible.

A new all-sky visible and Near-InfraRed (NIR) space astrometry mission with a wavelength cutoff in the K-band is not just focused on a single or small number of key science cases. Instead, it is extremely broad, answering key science questions in nearly every branch of astronomy while also providing a dense and accurate visible-NIR reference frame needed for future astronomy facilities. For almost 2 billion common stars the combination of Gaia and a new all-sky NIR astrometry mission would provide much improved proper motions, answering key science questions -- from the solar system and stellar systems, including exoplanet systems, to compact galaxies, quasars, neutron stars, binaries and dark matter substructures. The addition of NIR will result in up to 8 billion newly measured stars in some of the most obscured parts of our Galaxy, and crucially reveal the very heart of the Galactic bulge region. In this white paper we argue that rather than improving on the accuracy, a greater overall science return can be achieved by going deeper than Gaia and by expanding the wavelength range to the NIR.

Gaia is a revolutionary space mission developed by ESA and is delivering 5 parameter astrometry, photometry and radial velocities over the whole sky with astrometric accuracies down to a few tens of micro-arcseconds. A weakness of Gaia is that it only operates at optical wavelengths. However, much of the Galactic centre and the spiral arm regions, important for certain studies, are obscured by interstellar extinction and this makes it difficult for Gaia to deeply probe. This problem can be overcome by switching to the Near Infra-Red (NIR) but this is not possible with silicon CCDs. Additionally, to scan the entire sky and make global absolute parallax measurements the spacecraft must have a constant rotation and this requires the detectors operate in Time Delayed Integration (TDI) mode or similar.

Theory suggests that there are two primary modes of accretion through which dark matter halos acquire the gas to form and fuel galaxies, hot and cold mode accretion. In cold mode accretion, gas streams along cosmic web filaments to the center of the halo, allowing for the efficient delivery of star-forming fuel. Recently, two QSO-illuminated HI Lyman alpha (Ly{\alpha}) emitting objects were reported to have properties of cold, rotating structures (Martin et al. 2015, Martin et al. 2016). However, the spatial and spectral resolution available was insufficient to constrain radial flows associated with connecting filaments. With the Keck Cosmic Web Imager (KCWI) we now have eight times the spatial resolution, permitting the detection of these in-spiraling flows. In order to detect these inflows, we introduce a suite of models which incorporate zonal radial flows, demonstrate their performance on a numerical simulation that exhibits coldflow accretion, and show that they are an excellent match to KCWI velocity maps of two Ly{\alpha} emitters observed around high-redshift quasars. These Multi-Filament Inflow models kinematically isolate zones of radial inflow that correspond to extended filamentary emission. The derived gas flux and inflow path is sufficient to fuel the inferred central galaxy star formation rate and angular momentum. Thus, our kinematic emission maps provide strong evidence for the inflow of gas from the cosmic web building galaxies at the peak of star formation.

Opening up the dynamic infrared sky for systematic time-domain exploration would yield many scientific advances. Multi-messenger pursuits such as localizing gravitational waves from neutron star mergers and quantifying the nucleosynthetic yields require the infrared. Another multi-messenger endeavor that needs infrared surveyors is the study of the much-awaited supernova in our own Milky Way. Understanding shocks in novae, true rates of supernovae and stellar mergers are some other examples of stellar evolution and high energy physics wherein the answers are buried in the infrared. We discuss some of the challenges in the infrared and pathfinders to overcome them. We conclude with recommendations on both infrared discovery engines and infrared follow-up machines that would enable this field to flourish in the next decade.

We present Keck/KCWI integral field spectrograph observations of the complex system surrounding SMM J02399$-$0136 (a lensed $z=2.8$ sub-mm galaxy), including an associated Ly$\rm \alpha$ nebula, a dust-obscured, broad-absorption-line quasar, and neighboring galaxies. At a 3$\sigma$ surface brightness contour of 1.6$\times$ 10$^{-17}$ erg s$^{-1}$ cm$^{-2}$ arcsec$^{-2}$, the Ly$\rm \alpha$ nebula extends over 17 arcsec ($\gtrsim 140$ physical kpc) and has a total Ly$\rm \alpha$ luminosity of $2.5 \times 10^{44} \, \rm erg \, s^{-1}$ (uncorrected for lensing). The nebula exhibits a kinematic shear of $\sim$ 1000 km s$^{-1}$ over 100 pkpc with lowest velocities east of SMM J02399$-$0136 and increasing to the southwest. We also discover a bright, Ly$\rm \alpha$ emitter, separated spatially and kinematically from the nebula, at a projected separation of $\approx$60 kpc from the quasar. This source has no clear central counterpart in deep $Hubble \, Space \, Telescope$ imaging, giving an intrinsic Ly$\rm \alpha$ rest-frame equivalent width greater than 312 $ \rm \mathring{A}$ (5-$\sigma$). We argue that this 'dark cloud' is illuminated by the quasar with a UV flux that is orders of magnitude brighter than the emission along our sightline. This result confirms statistical inferences that luminous quasars at $z>2$ emit UV radiation anisotropically. Future KCWI observations of other lines, e.g. Ly$\rm \beta$, He$\rm _{II}$, C$\rm _{IV}$, etc, and with polarimetry will further reveal the origin of the Ly$\rm \alpha$ nebula and nature of the dark cloud.

We report on the design and performance of the Keck Cosmic Web Imager (KCWI), a general purpose optical integral field spectrograph that has been installed at the Nasmyth port of the 10 m Keck II telescope on Mauna Kea, HI. The novel design provides blue-optimized seeing-limited imaging from 350-560 nm with configurable spectral resolution from 1000 - 20000 in a field of view up to 20"x33". Selectable volume phase holographic (VPH) gratings and high performance dielectric, multilayer silver and enhanced aluminum coatings provide end-to-end peak efficiency in excess of 45% while accommodating the future addition of a red channel that will extend wavelength coverage to 1 micron. KCWI takes full advantage of the excellent seeing and dark sky above Mauna Kea with an available nod-and-shuffle observing mode. The instrument is optimized for observations of faint, diffuse objects such as the intergalactic medium or cosmic web. In this paper, a detailed description of the instrument design is provided with measured performance results from the laboratory test program and ten nights of on-sky commissioning during the spring of 2017. The KCWI team is lead by Caltech and JPL (project management, design and implementation) in partnership with the University of California at Santa Cruz (camera optical and mechanical design) and the W. M. Keck Observatory (observatory interfaces).

We are building a next-generation laser adaptive optics system, Robo-AO-2, for the UH 2.2-m telescope that will deliver robotic, diffraction-limited observations at visible and near-infrared wavelengths in unprecedented numbers. The superior Maunakea observing site, expanded spectral range and rapid response to high-priority events represent a significant advance over the prototype. Robo-AO-2 will include a new reconfigurable natural guide star sensor for exquisite wavefront correction on bright targets and the demonstration of potentially transformative hybrid AO techniques that promise to extend the faintness limit on current and future exoplanet adaptive optics systems.

We describe test observations made with a customized 640 x 512 pixel Indium Gallium Arsenide (InGaAs) prototype astronomical camera on the 100" DuPont telescope. This is the first test of InGaAs as a cost-effective alternative to HgCdTe for research-grade astronomical observations. The camera exhibits an instrument background of 113 e-/sec/pixel (dark + thermal) at an operating temperature of -40C for the sensor, maintained by a simple thermo-electric cooler. The optical train and mechanical structure float at ambient temperature with no cold stop, in contrast to most IR instruments which must be cooled to mitigate thermal backgrounds. Measurements of the night sky using a reimager with plate scale of 0.4 arc seconds / pixel show that the sky flux in Y is comparable to the dark current. At J the sky brightness exceeds dark current by a factor of four, and hence dominates the noise budget. The sensor read noise of ~43e- falls below sky+dark noise for exposures of t>7 seconds in Y and 3.5 seconds in J. We present test observations of several selected science targets, including high-significance detections of a lensed Type Ia supernova, a type IIb supernova, and a z=6.3 quasar. Deeper images are obtained for two local galaxies monitored for IR transients, and a galaxy cluster at z=0.87. Finally, we observe a partial transit of the hot JupiterHATS34b, demonstrating the photometric stability required over several hours to detect a 1.2% transit depth at high significance. A tiling of available larger-format sensors would produce an IR survey instrument with significant cost savings relative to HgCdTe-based cameras, if one is willing to forego the K band. Such a camera would be sensitive for a week or more to isotropic emission from r-process kilonova ejecta similar to that observed in GW170817, over the full 190 Mpc horizon of Advanced LIGO's design sensitivity for neutron star mergers.

Post starburst E+A galaxies show indications of a powerful starburst that was quenched abruptly. Their disturbed, bulge-dominated morphologies suggest that they are merger remnants. The more massive E+A galaxies are suggested to be quenched by AGN feedback, yet little is known about AGN-driven winds in this short-lived phase. We present spatially-resolved IFU spectroscopy by the Keck Cosmic Web Imager of SDSS J003443.68+251020.9, at z=0.118. The system consists of two galaxies, the larger of which is a post starburst E+A galaxy hosting an AGN. Our modelling suggests a 400 Myrs starburst, with a peak star formation rate of 120 Msun/yr. The observations reveal stationary and outflowing gas, photoionized by the central AGN. We detect gas outflows to a distance of 17 kpc from the central galaxy, far beyond the region of the stars (about 3 kpc), inside a conic structure with an opening angle of 70 degrees. We construct self-consistent photoionization and dynamical models for the different gas components and show that the gas outside the galaxy forms a continuous flow, with a mass outflow rate of about 24 Msun/yr. The gas mass in the flow, roughly $10^9$ Msun, is larger than the total gas mass within the galaxy, some of which is outflowing too. The continuity of the flow puts a lower limit of 60 Myrs on the duration of the AGN feedback. Such AGN are capable of removing, in a single episode, most of the gas from their host galaxies and expelling enriched material into the surrounding CGM.

Enormous Ly$\alpha$ nebulae (ELANe) represent the extrema of Ly$\alpha$ nebulosities. They have detected extents of $>200$ kpc in Ly$\alpha$ and Ly$\alpha$ luminosities $>10^{44}$ erg s$^{-1}$. The ELAN population is an ideal laboratory to study the interactions between galaxies and the intergalactic/circumgalactic medium (IGM/CGM) given their brightness and sizes. The current sample size of ELANe is still very small, and the few $z\approx2$ ELANe discovered to date are all associated with local overdensities of active galactic nuclei (AGNs). Inspired by these results, we have initiated a survey of ELANe associated with QSO pairs using the Palomar and Keck Cosmic Web Imagers (PCWI/KCWI). In this letter, we present our first result: the discovery of ELAN0101+0201 associated with a QSO pair at $z=2.45$. Our PCWI discovery data shows that, above a 2-$\sigma$ surface brightness of $1.2\times10^{-17}$ \sbunit, the end-to-end size of ELAN0101+0201 is $\gtrsim 232$ kpc. We have conducted follow-up observations using KCWI, resolving multiple Ly$\alpha$ emitting sources within the rectangular field-of-view of $\approx 130\times165$ projected kpc$^2$, and obtaining their emission line profiles at high signal-to-noise ratios. Combining both KCWI and PCWI, our observations confirm that ELAN0101+0201 resides in an extremely overdense environment. Our observations further support that a large amount of cool ($T\sim10^4$K) gas could exist in massive halos (M$\gtrsim10^{13}$M$_\odot$) at $z\approx2$. Future observations on a larger sample of similar systems will provide statistics of how cool gas is distributed in massive overdensities at high-redshift and strongly constrain the evolution of the intracluster medium (ICM).

We present Keck Cosmic Web Imager spectroscopy of the four putative images of the lensed quasar candidate J014709+463037 recently discovered by Berghea et al. (2017). The data verify the source as a quadruply lensed, broad absorption-line quasar having z_S = 2.377 +/- 0.007. We detect intervening absorption in the FeII 2586, 2600, MgII 2796, 2803, and/or CIV 1548, 1550 transitions in eight foreground systems, three of which have redshifts consistent with the photometric-redshift estimate reported for the lensing galaxy (z_L ~ 0.57). By virtue of their positions on the sky, the source images probe these absorbers over transverse physical scales of ~0.3-21 kpc, permitting assessment of the variation in metal-line equivalent width W_r as a function of sight-line separation. We measure differences in W_r,2796 of <40% across all sight-line pairs subtending 7-21 kpc, suggestive of a high degree of spatial coherence for MgII-absorbing material. W_r,2600 is observed to vary by >50% over the same scales across the majority of sight-line pairs, while CIV absorption exhibits a wide range in W_r,1548 differences of ~5-80% within transverse distances less than ~3 kpc. J014709+463037 is one of only a handful of z > 2 quadruply lensed systems for which all four source images are very bright (r = 15.4-17.7 mag) and are easily separated in ground-based seeing conditions. As such, it is an ideal candidate for higher-resolution spectroscopy probing the spatial variation in the kinematic structure and physical state of intervening absorbers.

The summit of the Antarctic plateau, Dome A, is proving to be an excellent site for optical, NIR, and THz astronomical observations. GATTINI was a wide-field camera installed on the PLATO instrument module as part of the Chinese-led traverse to Dome A in January, 2009. We present here the measurements of sky brightness with the Gattini ultra-large field of view (90 deg x 90 deg) in the photometric B-, V-, and R-bands, cloud cover statistics measured during the 2009 winter season, and an estimate of the sky transparency. A cumulative probability distribution indicates that the darkest 10% of the nights at Dome A have sky brightness of S_B = 22.98, S_V = 21.86, and S_R = 21.68 mag arcsec^{-2}. These values were obtained around the year 2009 with minimum aurora, and they are comparable to the faintest sky brightness at Mauna Kea and the best sites of northern Chile. Since every filter includes strong auroral lines that effectively contaminate the sky brightness measurements, for instruments working around the auroral lines, either with custom filters or with high spectral resolution instruments, these values could be easily obtained on a more routine basis. In addition, we present example light curves for bright targets to emphasize the unprecedented observational window function available from this ground-based site. These light curves will be published in a future paper.

We present an ongoing, systematic search for extragalactic infrared transients, dubbed SPIRITS --- SPitzer InfraRed Intensive Transients Survey. In the first year, using Spitzer/IRAC, we searched 190 nearby galaxies with cadence baselines of one month and six months. We discovered over 1958 variables and 43 transients. Here, we describe the survey design and highlight 14 unusual infrared transients with no optical counterparts to deep limits, which we refer to as SPRITEs (eSPecially Red Intermediate Luminosity Transient Events). SPRITEs are in the infrared luminosity gap between novae and supernovae, with [4.5] absolute magnitudes between -11 and -14 (Vega-mag) and [3.6]-[4.5] colors between 0.3 mag and 1.6 mag. The photometric evolution of SPRITEs is diverse, ranging from < 0.1 mag/yr to > 7 mag/yr. SPRITEs occur in star-forming galaxies. We present an in-depth study of one of them, SPIRITS 14ajc in Messier 83, which shows shock-excited molecular hydrogen emission. This shock may have been triggered by the dynamic decay of a non-hierarchical system of massive stars that led to either the formation of a binary or a proto-stellar merger.

While optical and radio transient surveys have enjoyed a renaissance over the past decade, the dynamic infrared sky remains virtually unexplored. The infrared is a powerful tool for probing transient events in dusty regions that have high optical extinction, and for detecting the coolest of stars that are bright only at these wavelengths. The fundamental roadblocks in studying the infrared time-domain have been the overwhelmingly bright sky background (250 times brighter than optical) and the narrow field-of-view of infrared cameras (largest is 0.6 sq deg). To begin to address these challenges and open a new observational window in the infrared, we present Palomar Gattini-IR: a 25 sq degree, 300mm aperture, infrared telescope at Palomar Observatory that surveys the entire accessible sky (20,000 sq deg) to a depth of 16.4 AB mag (J band, 1.25um) every night. Palomar Gattini-IR is wider in area than every existing infrared camera by more than a factor of 40 and is able to survey large areas of sky multiple times. We anticipate the potential for otherwise infeasible discoveries, including, for example, the elusive electromagnetic counterparts to gravitational wave detections. With dedicated hardware in hand, and a F/1.44 telescope available commercially and cost-effectively, Palomar Gattini-IR will be on-sky in early 2017 and will survey the entire accessible sky every night for two years. Palomar Gattini-IR will pave the way for a dual hemisphere, infrared-optimized, ultra-wide field high cadence machine called Turbo Gattini-IR. To take advantage of the low sky background at 2.5 um, two identical systems will be located at the polar sites of the South Pole, Antarctica and near Eureka on Ellesmere Island, Canada. Turbo Gattini-IR will survey 15,000 sq. degrees to a depth of 20AB, the same depth of the VISTA VHS survey, every 2 hours with a survey efficiency of 97%.

TMT has defined the accuracy to be achieved for both absolute and differential astrometry in its top-level requirements documents. Because of the complexities of different types of astrometric observations, these requirements cannot be used to specify system design parameters directly. The TMT astrometry working group therefore developed detailed astrometry error budgets for a variety of science cases. These error budgets detail how astrometric errors propagate through the calibration, observing and data reduction processes. The budgets need to be condensed into sets of specific requirements that can be used by each subsystem team for design purposes. We show how this flowdown from error budgets to design requirements is achieved for the case of TMT's first-light Infrared Imaging Spectrometer (IRIS) instrument.

The InfraRed Imaging Spectrograph (IRIS) will be a first-light client instrument for the Narrow Field Infrared Adaptive Optics System (NFIRAOS) on the Thirty Meter Telescope. IRIS includes three configurable tip/tilt (TT) or tip/tilt/focus (TTF) On-Instrument Wavefront Sensors (OIWFS). These sensors are positioned over natural guide star (NGS) asterisms using movable polar-coordinate pick-off arms (POA) that patrol an approximately 2-arcminute circular field-of-view (FOV). The POAs are capable of colliding with one another, so an algorithm for coordinated motion that avoids contact is required. We have adopted an approach in which arm motion is evaluated using the gradient descent of a scalar potential field that includes an attractive component towards the goal configuration (locations of target stars), and repulsive components to avoid obstacles (proximity to adjacent arms). The resulting vector field is further modified by adding a component transverse to the repulsive gradient to avoid problematic local minima in the potential. We present path planning simulations using this computationally inexpensive technique, which exhibit smooth and efficient trajectories.

The InfraRed Imaging Spectrograph (IRIS) will be the first light adaptive optics instrument on the Thirty Meter Telescope (TMT). IRIS is being built by a collaboration between Caltech, the University of California, NAOJ and NRC Herzberg. We present novel aspects of the Support Structure, Rotator and On-Instrument Wavefront Sensor systems being developed at NRC Herzberg. IRIS is suspended from the bottom port of the Narrow Field Infrared Adaptive Optics System (NFIRAOS), and provides its own image de-rotation to compensate for sidereal rotation of the focal plane. This arrangement is a challenge because NFIRAOS is designed to host two other science instruments, which imposes strict mass requirements on IRIS. We have been tasked with keeping the instrument mass under seven tonnes which has resulted in a mass reduction of 30 percent for the support structure and rotator compared to the most recent IRIS designs. To accomplish this goal, while still being able to withstand earthquakes, we developed a new design with composite materials. As IRIS is a client instrument of NFIRAOS, it benefits from NFIRAOS's superior AO correction. IRIS assists this correction by sensing low-order aberrations with an On-Instrument Wavefront Sensor (OIWFS). The OIWFS consists of three independently positioned natural guide star wavefront sensors that patrol a 2-arcminute field of view. We expect tip-tilt measurements from faint stars within the IRIS imager focal plane will further stabilize the delivered image quality. We describe how the use of On-Detector Guide Windows (ODGWs) in the IRIS imager can be incorporated into the AO correction. Finally, we present our strategies for acquiring and tracking sources with this complex AO system, and for mitigating and measuring the various potential sources of image blur and misalignment due to properties of the mechanical structure and interfaces. (Abridged)

IRIS (InfraRed Imaging Spectrograph) is the diffraction-limited first light instrument for the Thirty Meter Telescope (TMT) that consists of a near-infrared (0.84 to 2.4 $\mu$m) imager and integral field spectrograph (IFS). The IFS makes use of a lenslet array and slicer for spatial sampling, which will be able to operate in 100's of different modes, including a combination of four plate scales from 4 milliarcseconds (mas) to 50 mas with a large range of filters and gratings. The imager will have a field of view of 34$\times$34 arcsec$^{2}$ with a plate scale of 4 mas with many selectable filters. We present the preliminary design of the data reduction system (DRS) for IRIS that need to address all of these observing modes. Reduction of IRIS data will have unique challenges since it will provide real-time reduction and analysis of the imaging and spectroscopic data during observational sequences, as well as advanced post-processing algorithms. The DRS will support three basic modes of operation of IRIS; reducing data from the imager, the lenslet IFS, and slicer IFS. The DRS will be written in Python, making use of open-source astronomical packages available. In addition to real-time data reduction, the DRS will utilize real-time visualization tools, providing astronomers with up-to-date evaluation of the target acquisition and data quality. The quicklook suite will include visualization tools for 1D, 2D, and 3D raw and reduced images. We discuss the overall requirements of the DRS and visualization tools, as well as necessary calibration data to achieve optimal data quality in order to exploit science cases across all cosmic distance scales.

The Thirty Meter Telescope (TMT) first light instrument IRIS (Infrared Imaging Spectrograph) will complete its preliminary design phase in 2016. The IRIS instrument design includes a near-infrared (0.85 - 2.4 micron) integral field spectrograph (IFS) and imager that are able to conduct simultaneous diffraction-limited observations behind the advanced adaptive optics system NFIRAOS. The IRIS science cases have continued to be developed and new science studies have been investigated to aid in technical performance and design requirements. In this development phase, the IRIS science team has paid particular attention to the selection of filters, gratings, sensitivities of the entire system, and science cases that will benefit from the parallel mode of the IFS and imaging camera. We present new science cases for IRIS using the latest end-to-end data simulator on the following topics: Solar System bodies, the Galactic center, active galactic nuclei (AGN), and distant gravitationally-lensed galaxies. We then briefly discuss the necessity of an advanced data management system and data reduction pipeline.

IRIS (InfraRed Imaging Spectrograph) is one of the first-generation instruments for the Thirty Meter Telescope (TMT). IRIS is composed of a combination of near-infrared (0.84--2.4 $\mu$m) diffraction limited imager and integral field spectrograph. To achieve near-diffraction limited resolutions in the near-infrared wavelength region, IRIS uses the advanced adaptive optics system NFIRAOS (Narrow Field Infrared Adaptive Optics System) and integrated on-instrument wavefront sensors (OIWFS). However, IRIS itself has challenging specifications. First, the overall system wavefront error should be less than 40 nm in Y, z, J, and H-band and 42 nm in K-band over a 34.0 $\times$ 34.0 arcsecond field of view. Second, the throughput of the imager components should be more than 42 percent. To achieve the extremely low wavefront error and high throughput, all reflective design has been newly proposed. We have adopted a new design policy called "Co-Axis double-TMA", which cancels the asymmetric aberrations generated by "collimator/TMA" and "camera/TMA" efficiently. The latest imager design meets all specifications, and, in particular, the wavefront error is less than 17.3 nm and throughput is more than 50.8 percent. However, to meet the specification of wavefront error and throughput as built performance, the IRIS imager requires both mirrors with low surface irregularity after high-reflection coating in cryogenic and high-level Assembly Integration and Verification (AIV). To deal with these technical challenges, we have done the tolerance analysis and found that total pass rate is almost 99 percent in the case of gauss distribution and more than 90 percent in the case of parabolic distribution using four compensators. We also have made an AIV plan and feasibility check of the optical elements. In this paper, we will present the details of this optical system.

We present the current optical design for the IRIS Atmospheric Dispersion Corrector (ADC). The ADC is designed for residual dispersions less than ~1 mas across a given passband at elevations of 25 degrees. Since the last report, the area of the IRIS Imager has increased by a factor of four, and the pupil size has increased from 75 to 90mm, both of which contribute to challenges with the design. Several considerations have led to the current design: residual dispersion, amount of introduced distortion, glass transmission, glass availability, and pupil displacement. In particular it was found that there are significant distortions that appear (two different components) that can lead to image blur over long exposures. Also, pupil displacement increases the wavefront error at the imager focus. We discuss these considerations, discuss the compromises, and present the final design choice and expected performance.

IRIS is a near-infrared (0.84 to 2.4 microns) integral field spectrograph and wide-field imager being developed for first light with the Thirty Meter (TMT). It mounts to the advanced optics (AO) system NFIRAOS and has integrated on-instrument wavefront sensors (OIWFS) to achieve diffraction-limited spatial resolution at wavelengths longer than 1 micron. With moderate spectral resolution (R ~4,000 - 8,000) and large bandpass over a continuous field of view, IRIS will open new opportunities in virtually every area of astrophysical science. It will be able to resolve surface features tens of kilometers across Titan, while also mapping the distant galaxies at the scale of an individual star forming region. This paper summarizes the entire design and capabilities, and includes the results from the nearly completed preliminary design phase.

We outline a technique called Dual Plane Imaging which should significantly improve images which would otherwise be blurred due to atmospheric turbulence. The technique involves capturing all the spatial, directional and temporal information about the arriving photons and processing the data afterwards to produce the sharpened images. The technique has particular relevance for imaging at around 400-1000nm on extremely large telescopes (ELTs).

IRIS (InfraRed Imaging Spectrograph) is a first light near-infrared diffraction limited imager and integral field spectrograph being designed for the future Thirty Meter Telescope (TMT). IRIS is optimized to perform astronomical studies across a significant fraction of cosmic time, from our Solar System to distant newly formed galaxies (Barton et al. [1]). We present a selection of the innovative science cases that are unique to IRIS in the era of upcoming space and ground-based telescopes. We focus on integral field spectroscopy of directly imaged exoplanet atmospheres, probing fundamental physics in the Galactic Center, measuring 10^4 to 10^10 Msun supermassive black hole masses, resolved spectroscopy of young star-forming galaxies (1 < z < 5) and first light galaxies (6 < z < 12), and resolved spectroscopy of strong gravitational lensed sources to measure dark matter substructure. For each of these science cases we use the IRIS simulator (Wright et al. [2], Do et al. [3]) to explore IRIS capabilities. To highlight the unique IRIS capabilities, we also update the point and resolved source sensitivities for the integral field spectrograph (IFS) in all five broadband filters (Z, Y, J, H, K) for the finest spatial scale of 0.004" per spaxel. We briefly discuss future development plans for the data reduction pipeline and quicklook software for the IRIS instrument suite.

We present an overview of the design of IRIS, an infrared (0.84 - 2.4 micron) integral field spectrograph and imaging camera for the Thirty Meter Telescope (TMT). With extremely low wavefront error (<30 nm) and on-board wavefront sensors, IRIS will take advantage of the high angular resolution of the narrow field infrared adaptive optics system (NFIRAOS) to dissect the sky at the diffraction limit of the 30-meter aperture. With a primary spectral resolution of 4000 and spatial sampling starting at 4 milliarcseconds, the instrument will create an unparalleled ability to explore high redshift galaxies, the Galactic center, star forming regions and virtually any astrophysical object. This paper summarizes the entire design and basic capabilities. Among the design innovations is the combination of lenslet and slicer integral field units, new 4Kx4k detectors, extremely precise atmospheric dispersion correction, infrared wavefront sensors, and a very large vacuum cryogenic system.

The first light instrument on the Thirty Meter Telescope (TMT) project will be the InfraRed Imaging Spectrograph (IRIS). IRIS will be mounted on a bottom port of the facility AO instrument NFIRAOS. IRIS will report guiding information to the NFIRAOS through the On-Instrument Wavefront Sensor (OIWFS) that is part of IRIS. This will be in a self-contained compartment of IRIS and will provide three deployable wavefront sensor probe arms. This entire unit will be rotated to provide field de-rotation. Currently in our preliminary design stage our efforts have included: prototyping of the probe arm to determine the accuracy of this critical component, handling cart design and reviewing different types of glass for the atmospheric dispersion.

Maximizing the grating efficiency is a key goal for the first light instrument IRIS (Infrared Imaging Spectrograph) currently being designed to sample the diffraction limit of the TMT (Thirty Meter Telescope). Volume Phase Holographic (VPH) gratings have been shown to offer extremely high efficiencies that approach 100% for high line frequencies (i.e., 600 to 6000l/mm), which has been applicable for astronomical optical spectrographs. However, VPH gratings have been less exploited in the near-infrared, particularly for gratings that have lower line frequencies. Given their potential to offer high throughputs and low scattered light, VPH gratings are being explored for IRIS as a potential dispersing element in the spectrograph. Our team has procured near-infrared gratings from two separate vendors. We have two gratings with the specifications needed for IRIS current design: 1.51-1.82{\mu}m (H-band) to produce a spectral resolution of 4000 and 1.19- 1.37 {\mu}m (J-band) to produce a spectral resolution of 8000. The center wavelengths for each grating are 1.629{\mu}m and 1.27{\mu}m, and the groove densities are 177l/mm and 440l/mm for H-band R=4000 and J-band R=8000, respectively. We directly measure the efficiencies in the lab and find that the peak efficiencies of these two types of gratings are quite good with a peak efficiency of ~88% at the Bragg angle in both TM and TE modes at H-band, and 90.23% in TM mode, 79.91% in TE mode at J-band for the best vendor. We determine the drop in efficiency off the Bragg angle, with a 20-23% decrease in efficiency at H-band when 2.5 degree deviation from the Bragg angle, and 25%-28% decrease at J-band when 5{\deg} deviation from the Bragg angle.

We present the efficiency of near-infrared reflective ruled diffraction gratings designed for the InfraRed Imaging Spectrograph (IRIS). IRIS is a first light, integral field spectrograph and imager for the Thirty Meter Telescope (TMT) and narrow field infrared adaptive optics system (NFIRAOS). We present our experimental setup and analysis of the efficiency of selected reflective diffraction gratings. These measurements are used as a comparison sample against selected candidate Volume Phase Holographic (VPH) gratings (see Chen et al., this conference). We investigate the efficiencies of five ruled gratings designed for IRIS from two separate vendors. Three of the gratings accept a bandpass of 1.19-1.37 {\mu}m (J band) with ideal spectral resolutions of R=4000 and R=8000, groove densities of 249 and 516 lines/mm, and blaze angles of 9.86 and 20.54 degrees, respectively. The other two gratings accept a bandpass of 1.51-1.82 {\mu}m (H Band) with an ideal spectral resolution of R=4000, groove density of 141 lines/mm, and blaze angle of 9.86{\deg}. We measure the efficiencies off blaze angle for all gratings and the efficiencies between the polarization transverse magnetic (TM) and transverse electric (TE) states. The peak reflective efficiencies are 98.90 +/- 3.36% (TM) and 84.99 +/- 2.74% (TM) for the H-band R=4000 and J-band R=4000 respectively. The peak reflective efficiency for the J-band R=8000 grating is 78.78 +/- 2.54% (TE). We find that these ruled gratings do not exhibit a wide dependency on incident angle within +/-3{\deg}. Our best-manufactured gratings were found to exhibit a dependency on the polarization state of the incident beam with a ~10-20% deviation, consistent with the theoretical efficiency predictions.

The intergalactic medium (IGM) is the dominant reservoir of baryons, delineates the large scale structure at low to moderate overdensities, and provides gas from which galaxies form and evolve. Simulations of a Cold Dark Matter (CDM) dominated universe predict that the IGM is distributed in a cosmic web of filaments, and that galaxies should form along and at the intersections of these filaments (Bond et al. 1994; Miralda-Escude et al. 1996). While observations of QSO absorption lines and the large scale distribution of galaxies have confirmed the CDM paradigm, the cosmic web has never been confirmed by direct imaging. Here we report the Lyman-alpha blob 2 (LAB2) in SSA22, with the Cosmic Web Imager. This is an integral field spectrograph optimized for low surface brightness, extended emission. With 22 hours of total source exposure, CWI has revealed that LAB2 has extended Lyman-alpha emission which is consistent with filaments. We perform tests to secure the robustness of this result, which relies on data with modest signal-to-noise ratio. We have developed a smoothing algorithm that permits visualization of data cube slices along image or spectral-image planes. With both raw and smoothed data cubes we demonstrate that the filaments are kinematically associated with LAB2 and display double-peaked profiles of optically thick Lyman-alpha emission. The flux is 10 to 20x brighter than expected for the emission from the IGM but is consistent with boosted fluorescence from a buried QSO or gravitation cooling radiation. Using emission models we infer a baryon mass in the filaments of at least 1-4x10e11 Solar Mass, and the dark halo mass is at least 2x10e12 Solar Mass. The spatial kinematic morphology is more consistent with inflow from the cosmic web than outflow. LAB2 and the surrounding gas have significant and coaligned angular momentum, strengthening the case for their association.

The Palomar Cosmic Web Imager (PCWI), an integral field spectrograph designed to detect and map low surface brightness emission, has obtained imaging spectroscopic maps of Ly-alpha from the circum-QSO medium (CQM) of QSO HS1549+19 at redshift of 2.843. Extensive extended emission is detected from the CQM, consistent with fluorescent and pumped Ly-alpha produced by the ionizing and Ly-alpha continuum of the QSO. Many features present in PCWI spectral images match those detected in narrow-band images. Filamentary structures with narrow line profiles are detected in several cases as long as 250-400 kpc. One of these is centered at a velocity redshifted with respect to the systemic velocity, and displays a spatially collimated and kinematically cold line profile increasing in velocity width approaching the QSO. This suggests that the filament gas is infalling onto the QSO, perhaps in a cold accretion flow. Because of the strong ionizing flux, the neutral column density is low, typically N(HI) is roughly 10E12-10E15/square-cm, and the line center optical depth is also low (typically tau0 is less than 10), insufficient to display well-separated double peak emission characteristic of higher line optical depths. With a simple ionization and cloud model we can very roughly estimate the total gas mass (log M(gas) equal to 12.5 +/- 0.5) and the total mass (log M(tot) equal to 13.3+/- 0.5). We can also calculate a kinematic mass from the total line profile (2x10E13 M(sun)), which agrees with the mass estimated from the gas emission. The intensity-binned spectrum of the CQM shows a progression in kinematic properties consistent with heirarchical structure formation.

The next generation of giant-segmented mirror telescopes ($>$ 20 m) will enable us to observe galactic nuclei at much higher angular resolution and sensitivity than ever before. These capabilities will introduce a revolutionary shift in our understanding of the origin and evolution of supermassive black holes by enabling more precise black hole mass measurements in a mass range that is unreachable today. We present simulations and predictions of the observations of nuclei that will be made with the Thirty Meter Telescope (TMT) and the adaptive optics assisted integral-field spectrograph IRIS, which is capable of diffraction-limited spectroscopy from $Z$ band (0.9 $\mu$m) to $K$ band (2.2 $\mu$m). These simulations, for the first time, use realistic values for the sky, telescope, adaptive optics system, and instrument, to determine the expected signal-to-noise ratio of a range of possible targets spanning intermediate mass black holes of $\sim10^4$ \msun to the most massive black holes known today of $>10^{10}$ $M_\odot$. We find that IRIS will be able to observe Milky Way-mass black holes out the distance of the Virgo cluster, and will allow us to observe many more brightest cluster galaxies where the most massive black holes are thought to reside. We also evaluate how well the kinematic moments of the velocity distributions can be constrained at the different spectral resolutions and plate scales designed for IRIS. We find that a spectral resolution of $\sim8000$ will be necessary to measure the masses of intermediate mass black holes. By simulating the observations of galaxies found in SDSS DR7, we find that over $10^5$ massive black holes will be observable at distances between $0.005 < z < 0.18$ with the estimated sensitivity and angular resolution provided by access to $Z$-band (0.9 $\mu$m) spectroscopy from IRIS and the TMT adaptive optics system. (Abridged)

We explore scenarios for the origin of two different density planets in the Kepler 36 system in adjacent orbits near the 7:6 mean motion resonance. We find that fine tuning is required in the stochastic forcing amplitude, the migration rate and planet eccentricities to allow two convergently migrating planets to bypass mean motion resonances such as the 4:3, 5:4 and 6:5, and yet allow capture into the 7:6 resonance. Stochastic forcing can eject the system from resonance causing a collision between the planets, unless the disk inducing migration and stochastic forcing is depleted soon after resonance capture. We explore a scenario with approximately Mars mass embryos originating exterior to the two planets and migrating inwards toward two planets. We find that gravitational interactions with embryos can nudge the system out of resonances. Numerical integrations with about a half dozen embryos can leave the two planets in the 7:6 resonance. Collisions between planets and embryos have a wide distribution of impact angles and velocities ranging from accretionary to disruptive. We find that impacts can occur at sufficiently high impact angle and velocity that the envelope of a planet could have been stripped, leaving behind a dense core. Some of our integrations show the two planets exchanging locations, allowing the outer planet that had experienced multiple collisions with embryos to become the innermost planet. A scenario involving gravitational interactions and collisions with embryos may account for both the proximity of the Kepler 36 planets and their large density contrast.

HR 8799 is a four planet system that also hosts a debris disk. By numerically integrating both planets and a planetesimal disk, we find interactions between an exterior planetesimal disk and the planets can influence the lifetime of the system. We first consider resonant planetary configurations that remained stable for at least 7 Myrs sans debris disk. An exterior debris disk with only 1 per cent the mass of the outermost planet (approximately a Neptune mass) was sufficiently large enough to pull the system out of resonance after 2 to 6 Myrs. Secondly, we consider configurations which are unstable in less than a few hundred thousand years. We find that these can be stabilized by a debris disk with a mass of more than 10 per cent that of the outermost planet. Our two sets of simulations suggest that estimates of the long term stability of a planetary system should take into account the role of the debris disk.

A fraction of multiple planet candidate systems discovered from transits by the Kepler mission contain pairs of planet candidates that are in orbital resonance or are spaced slightly too far apart to be in resonance. We focus here on the four planet system, KOI 730, that has planet periods satisfying the ratios 8:6:4:3. By numerically integrating four planets initially in this resonant configuration in proximity to an initially exterior cold planetesimal disk, we find that of the order of a Mars mass of planet-orbit-crossing planetesimals is sufficient to pull this system out of resonance. Approximately one Earth mass of planet-orbit-crossing planetesimals increases the interplanetary spacings sufficiently to resemble the multiple planet candidate Kepler systems that lie just outside of resonance. This suggests that the closely spaced multiple planet Kepler systems, host only low mass debris disks or their debris disks have been extremely stable. We find that the planetary inclinations increase as a function of the mass in planetesimals that have crossed the orbits of the planets. If systems are left at zero inclination and in resonant chains after depletion of the gas disk then we would expect a correlation between distance to resonance and mutual planetary inclinations. This may make it possible to differentiate between dynamical mechanisms that account for the fraction of multiple planet systems just outside of resonance.

By logging encounters between planetesimals and planets we compute the distribution of encounters in a numerically integrated two planet system that is migrating due to interactions with an exterior planetesimal belt. Capture of an irregular satellite in orbit about a planet through an exchange reaction with a binary planetesimal is only likely when the binary planetesimal undergoes a slow and close encounter with the planet. In our simulations we find that close and slow encounters between planetesimals and a planet primarily occur with the outermost and not innermost planet. Taking care to consider where a planet orbit crossing binary planetesimal would first be tidally disrupted, we estimate the probability of both tidal disruption and irregular satellite capture. We estimate that the probability that the secondary of a binary planetesimal is captured and becomes an irregular satellite about a Neptune mass outer planet is about 1/100 for binaries with masses and separations similar to transneptunian planetesimal binaries. If young exoplanetary debris disks host a binary planetesimal population then outwards migrating outer planets should host captured irregular satellite populations. We discuss interpretation of emission associated with the exoplanet Fomalhaut b in terms of collisional evolution of a captured irregular satellite population that is replenished due to planetary migration.

The i-band observing conditions at Dome A on the Antarctic plateau have been investigated using data acquired during 2008 with the Chinese Small Telescope ARray. The sky brightness, variations in atmospheric transparency, cloud cover, and the presence of aurorae are obtained from these images. The median sky brightness of moonless clear nights is 20.5 mag arcsec^{-2} in the SDSS $i$ band at the South Celestial Pole (which includes a contribution of about 0.06 mag from diffuse Galactic light). The median over all Moon phases in the Antarctic winter is about 19.8 mag arcsec^{-2}. There were no thick clouds in 2008. We model contributions of the Sun and the Moon to the sky background to obtain the relationship between the sky brightness and transparency. Aurorae are identified by comparing the observed sky brightness to the sky brightness expected from this model. About 2% of the images are affected by relatively strong aurorae.

We describe a parallel hybrid symplectic integrator for planetary system integration that runs on a graphics processing unit (GPU). The integrator identifies close approaches between particles and switches from symplectic to Hermite algorithms for particles that require higher resolution integrations. The integrator is approximately as accurate as other hybrid symplectic integrators but is GPU accelerated.

The InfraRed Imaging Spectrograph (IRIS) is a first-light instrument being designed for the Thirty Meter Telescope (TMT). IRIS is a combination of an imager that will cover a 16.4" field of view at the diffraction limit of TMT (4 mas sampling), and an integral field unit spectrograph that will sample objects at 4-50 mas scales. IRIS will open up new areas of observational parameter space, allowing major progress in diverse fields of astronomy. We present the science case and resulting requirements for the performance of IRIS. Ultimately, the spectrograph will enable very well-resolved and sensitive studies of the kinematics and internal chemical abundances of high-redshift galaxies, shedding light on many scenarios for the evolution of galaxies at early times. With unprecedented imaging and spectroscopy of exoplanets, IRIS will allow detailed exploration of a range of planetary systems that are inaccessible with current technology. By revealing details about resolved stellar populations in nearby galaxies, it will directly probe the formation of systems like our own Milky Way. Because it will be possible to directly characterize the stellar initial mass function in many environments and in galaxies outside of the the Milky Way, IRIS will enable a greater understanding of whether stars form differently in diverse conditions. IRIS will reveal detailed kinematics in the centers of low-mass galaxies, allowing a test of black hole formation scenarios. Finally, it will revolutionize the characterization of reionization and the first galaxies to form in the universe.

We present an overview of the design of IRIS, an infrared (0.85 - 2.5 micron) integral field spectrograph and imaging camera for the Thirty Meter Telescope (TMT). With extremely low wavefront error (<30 nm) and on-board wavefront sensors, IRIS will take advantage of the high angular resolution of the narrow field infrared adaptive optics system (NFIRAOS) to dissect the sky at the diffraction limit of the 30-meter aperture. With a primary spectral resolution of 4000 and spatial sampling starting at 4 milliarcseconds, the instrument will create an unparalleled ability to explore high redshift galaxies, the Galactic center, star forming regions and virtually any astrophysical object. This paper summarizes the entire design and basic capabilities. Among the design innovations is the combination of lenslet and slicer integral field units, new 4Kx4k detectors, extremely precise atmospheric dispersion correction, infrared wavefront sensors, and a very large vacuum cryogenic system.

We present sensitivity estimates for point and resolved astronomical sources for the current design of the InfraRed Imaging Spectrograph (IRIS) on the future Thirty Meter Telescope (TMT). IRIS, with TMT's adaptive optics system, will achieve unprecedented point source sensitivities in the near-infrared (0.84 - 2.45 {\mu}m) when compared to systems on current 8-10m ground based telescopes. The IRIS imager, in 5 hours of total integration, will be able to perform a few percent photometry on 26 - 29 magnitude (AB) point sources in the near-infrared broadband filters (Z, Y, J, H, K). The integral field spectrograph, with a range of scales and filters, will achieve good signal-to-noise on 22 - 26 magnitude (AB) point sources with a spectral resolution of R=4,000 in 5 hours of total integration time. We also present simulated 3D IRIS data of resolved high-redshift star forming galaxies (1 < z < 5), illustrating the extraordinary potential of this instrument to probe the dynamics, assembly, and chemical abundances of galaxies in the early universe. With its finest spatial scales, IRIS will be able to study luminous, massive, high-redshift star forming galaxies (star formation rates ~ 10 - 100 M yr-1) at ~100 pc resolution. Utilizing the coarsest spatial scales, IRIS will be able to observe fainter, less massive high-redshift galaxies, with integrated star formation rates less than 1 M yr-1, yielding a factor of 3 to 10 gain in sensitivity compared to current integral field spectrographs. The combination of both fine and coarse spatial scales with the diffraction-limit of the TMT will significantly advance our understanding of early galaxy formation processes and their subsequent evolution into presentday galaxies.

We present a conceptual design for the atmospheric dispersion corrector (ADC) for TMT's Infrared Imaging Spectrograph (IRIS). The severe requirements of this ADC are reviewed, as are limitations to observing caused by uncorrectable atmospheric effects. The requirement of residual dispersion less than 1 milliarcsecond can be met with certain glass combinations. The design decisions are discussed and the performance of the design ADC is described. Alternative options and their performance tradeoffs are also presented.

The Infra-Red Imaging Spectrograph (IRIS) is one of the three first light instruments for the Thirty Meter Telescope (TMT) and is the only one to directly sample the diffraction limit. The instrument consists of a parallel imager and off-axis Integral Field Spectrograph (IFS) for optimum use of the near infrared (0.84um-2.4um) Adaptive Optics corrected focal surface. We present an overview of the IRIS spectrograph that is designed to probe a range of scientific targets from the dynamics and morphology of high-z galaxies to studying the atmospheres and surfaces of solar system objects, the latter requiring a narrow field and high Strehl performance. The IRIS spectrograph is a hybrid system consisting of two state of the art IFS technologies providing four plate scales (4mas, 9mas, 25mas, 50mas spaxel sizes). We present the design of the unique hybrid system that combines the power of a lenslet spectrograph and image slicer spectrograph in a configuration where major hardware is shared. The result is a powerful yet economical solution to what would otherwise require two separate 30m-class instruments.

The InfraRed Imaging Spectrograph (IRIS) is a first light client science instrument for the TMT observatory that operates as a client of the NFIRAOS facility multi-conjugate adaptive optics system. This paper reports on the concept study and baseline concept design of the On-Instrument WaveFront Sensors (OIWFS) and NFIRAOS interface subsystems of the IRIS science instrument, a collaborative effort by NRC-HIA, Caltech, and TMT AO and Instrument teams. This includes work on system engineering, structural and thermal design, sky coverage modeling, patrol geometry, probe optics and mechanics design, camera design, and controls design.

Fibre Multi-Object Spectrograph (FMOS) is the first near-infrared instrument with a wide field of view capable of acquiring spectra simultaneously from up to 400 objects. It has been developed as a common-use instrument for the F/2 prime-focus of the Subaru Telescope. The field coverage of 30' diameter is achieved using a new 3-element corrector optimized in the near-infrared (0.9-1.8um) wavelength range. Due to limited space at the prime-focus, we have had to develop a novel fibre positioner called "Echidna" together with two OH-airglow suppressed spectrographs. FMOS consists of three subsystems: the prime focus unit for IR, the fibre positioning system/connector units, and the two spectrographs. After full systems integration, FMOS was installed on the telescope in late 2007. Many aspects of performance were checked through various test and engineering observations. In this paper, we present the optical and mechanical components of FMOS and show the results of our on-sky engineering observations to date.

We present a close companion search around sixteen known early-L dwarfs using aperture masking interferometry with Palomar laser guide star adaptive optics. The use of aperture masking allows the detection of close binaries, corresponding to projected physical separations of 0.6-10.0 AU for the targets of our survey. This survey achieved median contrast limits of Delta_K ~ 2.3 for separations between 1.2 - 4 lambda/D, and Delta_K ~ 1.4 at (2/3)lambda/D. We present four candidate binaries detected with moderate to high confidence (90-98%). Two have projected physical separations less than 1.5 AU. This may indicate that tight-separation binaries contribute more significantly to the binary fraction than currently assumed, consistent with spectroscopic and photometric overluminosity studies. Ten targets of this survey have previously been observed with the Hubble Space Telescope as part of companion searches. We use the increased resolution of aperture masking to search for close or dim companions that would be obscured by full aperture imaging, finding two candidate binaries. This survey is the first application of aperture masking with laser guide star adaptive optics at Palomar. Several new techniques for the analysis of aperture masking data in the low signal to noise regime are explored.

In 2008 January the 24th Chinese expedition team successfully deployed the Chinese Small Telescope ARray (CSTAR) to DomeA, the highest point on the Antarctic plateau. CSTAR consists of four 14.5cm optical telescopes, each with a different filter (g, r, i and open) and has a 4.5degree x 4.5degree field of view (FOV). It operates robotically as part of the Plateau Observatory, PLATO, with each telescope taking an image every 30 seconds throughout the year whenever it is dark. During 2008, CSTAR #1 performed almost flawlessly, acquiring more than 0.3 million i-band images for a total integration time of 1728 hours during 158 days of observations. For each image taken under good sky conditions, more than 10,000 sources down to 16 mag could be detected. We performed aperture photometry on all the sources in the field to create the catalog described herein. Since CSTAR has a fixed pointing centered on the South Celestial Pole (Dec =-90 degree), all the sources within the FOV of CSTAR were monitored continuously for several months. The photometric catalog can be used for studying any variability in these sources, and for the discovery of transient sources such as supernovae, gamma-ray bursts and minor planets.

The cosmic dark ages are the mysterious epoch during which the pristine gas began to condense and ultimately form the first stars. Although these beginnings have long been a topic of theoretical interest, technology has only recently allowed the beginnings of observational insight into this epoch. Many questions surround the formation of stars in metal-free gas and the history of the build-up of metals in the intergalactic medium: (1) What were the properties of the first stellar and galactic sources to form in pristine (metal-free) gas? (2) When did the epoch of Population III (metal-free) star formation take place and how long did it last? (3) Was the stellar initial mass function dramatically different for the first stars and galaxies? These questions are all active areas of theoretical research. However, new observational constraints via the direct detection of Population III star formation are vital to making progress in answering the broader questions surrounding how galaxies formed and how the cosmological properties of the universe have affected the objects it contains.

We simulate planet migration caused by interactions between planets and a planetesimal disk. We use an N-body integrator optimized for near-Keplerian motion that runs in parallel on a video graphics card, and that computes all pair-wise gravitational interactions. We find that the fraction of planetesimals found in mean motion resonances is reduced and planetary migration rates are on average about 50% slower when gravitational interactions between the planetesimals are computed than when planetesimal self-gravity is neglected. This is likely due to gravitational stirring of the planetesimal disk that is not present when self-gravity is neglected that reduces their capture efficiency because of the increased particle eccentricity dispersion. We find that migration is more stochastic when the disk is self-gravitating or comprised of more massive bodies. Previous studies have found that if the planetesimal disk density is below a critical level, migration is "damped" and the migration rate decays exponentially, otherwise it is "forced" and the planet's migration rate could accelerate exponentially. Migration rates measured from our undamped simulations suggest that the migration rate saturates at a level proportional to disk density and subsequently is approximately power law in form with time.

We describe the results from a new instrument which combines Lucky Imaging and Adaptive Optics to give the first routine direct diffraction-limited imaging in the visible on a 5m telescope. With fast image selection behind the Palomar AO system we obtained Strehl ratios of 5-20% at 700 nm in a typical range of seeing conditions, with a median Strehl of approximately 12% when 10% of the input frames are selected. At wavelengths around 700 nm the system gave diffraction-limited 35 milliarcsecond FWHMs. At 950 nm the output Strehl ratio was as high as 36% and at 500 nm the FWHM resolution was as small as 42 milliarcseconds, with a low Strehl ratio but resolution improved by factor of ~20 compared to the prevailing seeing. To obtain wider fields we also used multiple Lucky-Imaging guide stars in a configuration similar to a ground layer adaptive optics system. With eight guide stars but very undersampled data we obtained 300 milliarcsecond resolution across a 30X30 arcsec field of view in i' band.

We consider constraints on the planetesimal population residing in the disks of AU Microscopii, Beta Pictoris and Fomalhaut taking into account their observed thicknesses and normal disk opacities. We estimate that bodies of radius 5, 180 and 70 km are responsible for initiating the collisional cascade accounting for the dust production for AU-Mic, Beta-Pic and Fomalhaut's disks, respectively, at break radii from the star where their surface brightness profiles change slope. Larger bodies, of radius 1000km and with surface density of order 0.01 g/cm^2, are required to explain the thickness of these disks assuming that they are heated by gravitational stirring. A comparison between the densities of the two sizes suggests the size distribution in the largest bodies is flatter than that observed in the Kuiper belt. AU Mic's disk requires the shallowest size distribution for bodies with radius greater than 10km suggesting that the disk contains planetary embryos experiencing a stage of runaway growth.

The Panoramic Survey Telescope And Rapid Response System (Pan-STARRS) under development at the University of Hawaii's Institute for Astronomy is creating the first fully automated end-to-end Moving Object Processing System (MOPS) in the world. It will be capable of identifying detections of moving objects in our solar system and linking those detections within and between nights, attributing those detections to known objects, calculating initial and differentially-corrected orbits for linked detections, precovering detections when they exist, and orbit identification. Here we describe new kd-tree and variable-tree algorithms that allow fast, efficient, scalable linking of intra and inter-night detections. Using a pseudo-realistic simulation of the Pan-STARRS survey strategy incorporating weather, astrometric accuracy and false detections we have achieved nearly 100% efficiency and accuracy for intra-night linking and nearly 100% efficiency for inter-night linking within a lunation. At realistic sky-plane densities for both real and false detections the intra-night linking of detections into `tracks' currently has an accuracy of 0.3%. Successful tests of the MOPS on real source detections from the Spacewatch asteroid survey indicate that the MOPS is capable of identifying asteroids in real data.

We present measurements of the normalised redshift-space three-point correlation function (Q_z) of galaxies from the Sloan Digital Sky Survey (SDSS) main galaxy sample. We have applied our "npt" algorithm to both a volume-limited (36738 galaxies) and magnitude-limited sample (134741 galaxies) of SDSS galaxies, and find consistent results between the two samples, thus confirming the weak luminosity dependence of Q_z recently seen by other authors. We compare our results to other Q_z measurements in the literature and find it to be consistent within the full jack-knife error estimates. However, we find these errors are significantly increased by the presence of the ``Sloan Great Wall'' (at z ~ 0.08) within these two SDSS datasets, which changes the 3-point correlation function (3PCF) by 70% on large scales (s>=10h^-1 Mpc). If we exclude this supercluster, our observed Q_z is in better agreement with that obtained from the 2dFGRS by other authors, thus demonstrating the sensitivity of these higher-order correlation functions to large-scale structures in the Universe. This analysis highlights that the SDSS datasets used here are not ``fair samples'' of the Universe for the estimation of higher-order clustering statistics and larger volumes are required. We study the shape-dependence of Q_z(s,q,theta) as one expects this measurement to depend on scale if the large scale structure in the Universe has grown via gravitational instability from Gaussian initial conditions. On small scales (s <= 6h^-1 Mpc), we see some evidence for shape-dependence in Q_z, but at present our measurements are consistent with a constant within the errors (Q_z ~ 0.75 +/- 0.05). On scales >10h^-1 Mpc, we see considerable shape-dependence in Q_z.

We outline our first steps towards marrying two new and emerging technologies; the Virtual Observatory (e.g, AstroGrid) and the computational grid. We discuss the construction of VOTechBroker, which is a modular software tool designed to abstract the tasks of submission and management of a large number of computational jobs to a distributed computer system. The broker will also interact with the AstroGrid workflow and MySpace environments. We present our planned usage of the VOTechBroker in computing a huge number of n-point correlation functions from the SDSS, as well as fitting over a million CMBfast models to the WMAP data.

There is a growing need for massive computational resources for the analysis of new astronomical datasets. To tackle this problem, we present here our first steps towards marrying two new and emerging technologies; the Virtual Observatory (e.g, AstroGrid) and the computational grid (e.g. TeraGrid, COSMOS etc.). We discuss the construction of VOTechBroker, which is a modular software tool designed to abstract the tasks of submission and management of a large number of computational jobs to a distributed computer system. The broker will also interact with the AstroGrid workflow and MySpace environments. We discuss our planned usages of the VOTechBroker in computing a huge number of n-point correlation functions from the SDSS data and massive model-fitting of millions of CMBfast models to WMAP data. We also discuss other applications including the determination of the XMM Cluster Survey selection function and the construction of new WMAP maps.

Many fundamental statistical methods have become critical tools for scientific data analysis yet do not scale tractably to modern large datasets. This paper will describe very recent algorithms based on computational geometry which have dramatically reduced the computational complexity of 1) kernel density estimation (which also extends to nonparametric regression, classification, and clustering), and 2) the n-point correlation function for arbitrary n. These new multi-tree methods typically yield orders of magnitude in speedup over the previous state of the art for similar accuracy, making millions of data points tractable on desktop workstations for the first time.

We discuss non-parametric density estimation and regression for astrophysics problems. In particular, we show how to compute non-parametric confidence intervals for the location and size of peaks of a function. We illustrate these ideas with recent data on the Cosmic Microwave Background. We also briefly discuss non-parametric Bayesian inference.

I present here a review of past and present multi-disciplinary research of the Pittsburgh Computational AstroStatistics (PiCA) group. This group is dedicated to developing fast and efficient statistical algorithms for analysing huge astronomical data sources. I begin with a short review of multi-resolutional kd-trees which are the building blocks for many of our algorithms. For example, quick range queries and fast n-point correlation functions. I will present new results from the use of Mixture Models (Connolly et al. 2000) in density estimation of multi-color data from the Sloan Digital Sky Survey (SDSS). Specifically, the selection of quasars and the automated identification of X-ray sources. I will also present a brief overview of the False Discovery Rate (FDR) procedure (Miller et al. 2001a) and show how it has been used in the detection of ``Baryon Wiggles'' in the local galaxy power spectrum and source identification in radio data. Finally, I will look forward to new research on an automated Bayes Network anomaly detector and the possible use of the Locally Linear Embedding algorithm (LLE; Roweis & Saul 2000) for spectral classification of SDSS spectra.

The False Discovery Rate (FDR) is a new statistical procedure to control the number of mistakes made when performing multiple hypothesis tests, i.e. when comparing many data against a given model hypothesis. The key advantage of FDR is that it allows one to a priori control the average fraction of false rejections made (when comparing to the null hypothesis) over the total number of rejections performed. We compare FDR to the standard procedure of rejecting all tests that do not match the null hypothesis above some arbitrarily chosen confidence limit, e.g. 2 sigma, or at the 95% confidence level. When using FDR, we find a similar rate of correct detections, but with significantly fewer false detections. Moreover, the FDR procedure is quick and easy to compute and can be trivially adapted to work with correlated data. The purpose of this paper is to introduce the FDR procedure to the astrophysics community. We illustrate the power of FDR through several astronomical examples, including the detection of features against a smooth one-dimensional function, e.g. seeing the ``baryon wiggles'' in a power spectrum of matter fluctuations, and source pixel detection in imaging data. In this era of large datasets and high precision measurements, FDR provides the means to adaptively control a scientifically meaningful quantity -- the number of false discoveries made when conducting multiple hypothesis tests.

We present here a new algorithm for the fast computation of N-point correlation functions in large astronomical data sets. The algorithm is based on kdtrees which are decorated with cached sufficient statistics thus allowing for orders of magnitude speed-ups over the naive non-tree-based implementation of correlation functions. We further discuss the use of controlled approximations within the computation which allows for further acceleration. In summary, our algorithm now makes it possible to compute exact, all-pairs, measurements of the 2, 3 and 4-point correlation functions for cosmological data sets like the Sloan Digital Sky Survey (SDSS; York et al. 2000) and the next generation of Cosmic Microwave Background experiments (see Szapudi et al. 2000).

We outline here the next generation of cluster-finding algorithms. We show how advances in Computer Science and Statistics have helped develop robust, fast algorithms for finding clusters of galaxies in large multi-dimensional astronomical databases like the Sloan Digital Sky Survey (SDSS). Specifically, this paper presents four new advances: (1) A new semi-parametric algorithm - nicknamed ``C4'' - for jointly finding clusters of galaxies in the SDSS and ROSAT All-Sky Survey databases; (2) The introduction of the False Discovery Rate into Astronomy; (3) The role of kernel shape in optimizing cluster detection; (4) A new determination of the X-ray Cluster Luminosity Function which has bearing on the existence of a ``deficit'' of high redshift, high luminosity clusters. This research is part of our ``Computational AstroStatistics'' collaboration (see Nichol et al. 2000) and the algorithms and techniques discussed herein will form part of the ``Virtual Observatory'' analysis toolkit.

In this paper, we outline the use of Mixture Models in density estimation of large astronomical databases. This method of density estimation has been known in Statistics for some time but has not been implemented because of the large computational cost. Herein, we detail an implementation of the Mixture Model density estimation based on multi-resolutional KD-trees which makes this statistical technique into a computationally tractable problem. We provide the theoretical and experimental background for using a mixture model of Gaussians based on the Expectation Maximization (EM) Algorithm. Applying these analyses to simulated data sets we show that the EM algorithm - using the AIC penalized likelihood to score the fit - out-performs the best kernel density estimate of the distribution while requiring no ``fine--tuning'' of the input algorithm parameters. We find that EM can accurately recover the underlying density distribution from point processes thus providing an efficient adaptive smoothing method for astronomical source catalogs. To demonstrate the general application of this statistic to astrophysical problems we consider two cases of density estimation: the clustering of galaxies in redshift space and the clustering of stars in color space. From these data we show that EM provides an adaptive smoothing of the distribution of galaxies in redshift space (describing accurately both the small and large-scale features within the data) and a means of identifying outliers in multi-dimensional color-color space (e.g. for the identification of high redshift QSOs). Automated tools such as those based on the EM algorithm will be needed in the analysis of the next generation of astronomical catalogs (2MASS, FIRST, PLANCK, SDSS) and ultimately in in the development of the National Virtual Observatory.

We present initial results on the use of Mixture Models for density estimation in large astronomical databases. We provide herein both the theoretical and experimental background for using a mixture model of Gaussians based on the Expectation Maximization (EM) Algorithm. Applying these analyses to simulated data sets we show that the EM algorithm - using the both the AIC & BIC penalized likelihood to score the fit - can out-perform the best kernel density estimate of the distribution while requiring no ``fine-tuning'' of the input algorithm parameters. We find that EM can accurately recover the underlying density distribution from point processes thus providing an efficient adaptive smoothing method for astronomical source catalogs. To demonstrate the general application of this statistic to astrophysical problems we consider two cases of density estimation; the clustering of galaxies in redshift space and the clustering of stars in color space. From these data we show that EM provides an adaptive smoothing of the distribution of galaxies in redshift space (describing accurately both the small and large-scale features within the data) and a means of identifying outliers in multi-dimensional color-color space (e.g. for the identification of high redshift QSOs). Automated tools such as those based on the EM algorithm will be needed in the analysis of the next generation of astronomical catalogs (2MASS, FIRST, PLANCK, SDSS) and ultimately in the development of the National Virtual Observatory.

A number of design options for image slicers for NGST and Gemini are being investigated. These image slicers are all of the focussing type and both refractive and reflective solutions are being explored. One such device, an image slicer that focuses 10 slices on a spectrograph slit is now in operation at the McMath Solar telescope. It consists of three lenslet arrays, and additionally acts as a focal reducer and provides correction for astigmatism of the telescope. A combined refractive and reflective slicer designed for use on NGST delivers near-diffraction limited images for up to 40 slices.