sort results by

Use logical operators AND, OR, NOT and round brackets to construct complex queries. Whitespace-separated words are treated as ANDed.

Show articles per page in mode

Coutts, D.

Normalized to: Coutts, D.

4 article(s) in total. 59 co-authors, from 1 to 4 common article(s). Median position in authors list is 6,0.

[1]  oai:arXiv.org:2003.08205  [pdf] - 2066592
Rubidium transitions as wavelength reference for astronomical Doppler spectrographs
Comments: SPIE ANZCOP conference, Melbourne 2019
Submitted: 2020-03-17
Precise wavelength calibration is a critical issue for high-resolution spectroscopic observations. The ideal calibration source should be able to provide a very stable and dense grid of evenly distributed spectral lines of constant intensity. A new method which satisfies all mentioned conditions has been developed by our group. The approach is to actively measure the exact position of a single spectral line of a Fabry-Perot etalon with very high precision with a wavelength-tuneable laser and compare it to an extremely stable wavelength standard. The ideal choice of standard is the D2 absorption line of Rubidium, which has been used as an optical frequency standard for decades. With this technique, the problem of stable wavelength calibration of spectrographs becomes a problem of how reliably we can measure and anchor one etalon line to the Rb transition. In this work we present our self-built module for Rb saturated absorption spectroscopy and discuss its stability.
[2]  oai:arXiv.org:1911.08325  [pdf] - 2000368
Fiber modal noise mitigation by a rotating double scrambler
Comments: SPIE ANZCOP conference, Melbourne 2019
Submitted: 2019-11-16
Fiber modal noise is a performance limiting factor in high-precision radial velocity measurements with multi-mode fiber-fed high-resolution spectrographs. Traditionally, modal noise is mitigated by agitating the fiber, this way redistributing the light that propagates in the fiber over many different modes. However, in case of fibers with only a limited number of modes, e.g. at near-infrared wavelengths or in adaptive-optics assisted systems, this method becomes very inefficient. The strong agitation that would be needed stresses the fiber and can lead to focal ratio degradation. As an alternative approach, we propose to use a classic optical double scrambler and to rotate the scrambler's first fiber end during each exposure. Because of the rotating illumination pattern of the scrambler's second fiber, the modes that are excited vary continuously. This leads to very efficient averaging of the modal pattern at the fiber exit and to a strong reduction of modal noise. In this contribution, we present a prototype design and first laboratory results of the rotating double scrambler.
[3]  oai:arXiv.org:1901.07567  [pdf] - 1821202
The need for single-mode fiber-fed spectrographs
Comments: A white paper submitted in response to the National Academy of Sciences 2018 Exoplanet Science Strategy solicitation
Submitted: 2019-01-22, last modified: 2019-01-24
Precise Doppler radial-velocity (RV) instruments will continue to play an essential role in advancing our holistic understanding of exoplanetary systems. The combination of orbital parameters from transit surveys and follow-up RV measurements is vital to unlock mass and density estimates of detected planets, giving us insight into their environment and structure. However, the exoplanet field is reaching a critical juncture: the measurement sensitivity of existing radial-velocity instruments is becoming the limiting factor in further increasing our knowledge. Without improvement in delivered RV measurement precision, we will not be able to provide dynamical mass and density estimates for some of the most exciting (and consequently most challenging) discoveries expected from new transit missions including the Transiting Exoplanet Survey Satellite (TESS) (Plavchan et al. 2015, Ricker et al. 2014). RV precisions at the 10cm/s level are required to fully confirm earth-like analogues, provide masses and measure density to the 1-5% level from these missions. Additionally, this RV capability will also be important to allow for efficient target selection for facilities such as the James Webb Space Telescope (JWST). A promising way forward to achieve this goal is to use single-mode fibers to inject light to a spectrograph. This mitigates many of the error terms facing current generation seeing-limited RV instruments while simultaneously offering the capability of high resolution spectroscopy within a small optical footprint (Schwab et al. 2012, Crepp 2014, Jovanovic et al. 2016a). We discuss the benefits of this technique, its challenges, and the current status of development.
[4]  oai:arXiv.org:1712.08584  [pdf] - 1607148
Pioneering high contrast science instruments for planet characterization on giant segmented mirror telescopes
Comments: 11 pages, 3 figures, AO4ELTs4 conference
Submitted: 2017-12-22
A suite of science instruments is critical to any high contrast imaging facility, as it defines the science capabilities and observing modes available. SCExAO uses a modular approach which allows for state-of-the-art visitor modules to be tested within an observatory environment on an 8-m class telescope. This allows for rapid prototyping of new and innovative imaging techniques that otherwise take much longer in traditional instrument design. With the aim of maturing science modules for an advanced high contrast imager on an giant segmented mirror telescopes (GSMTs) that will be capable of imaging terrestrial planets, we offer an overview and status update on the various science modules currently under test within the SCExAO instrument.