Sticking properties rule the early phases of pebble growth in protoplanetary discs in which grains regularly travel from cold, water-rich regions to the warm inner part. This drift affects composition, grain size, morphology, and water content as grains experience ever higher temperatures. In this study we tempered chondritic dust under vacuum up to 1400 K. Afterwards, we measured the splitting tensile strength of millimetre-sized dust aggregates. The deduced effective surface energy starts out as $\gamma_e = 0.07\,\rm J/m^2$. This value is dominated by abundant iron-oxides as measured by M\"ossbauer spectroscopy. Up to 1250 K, $\gamma_e$ continuously decreases by up to a factor five. Olivines dominate at higher temperature. Beyond 1300 K dust grains significantly grow in size. The $\gamma_e$ no longer decreases but the large grain size restricts the capability of growing aggregates. Beyond 1400 K aggregation is no longer possible. Overall, under the conditions probed, the stability of dust pebbles would decrease towards the star. In view of a minimum aggregate size required to trigger drag instabilities it becomes increasingly harder to seed planetesimal formation closer to a star.

Granular material that is bound by the low gravity of a small asteroid is mobilized by slow velocity impacts. These splashes generated by impacts might play an important role in sculpting the asteroid's surface. In laboratory experiments we characterize the ejecta generated by spherical 150 $\rm \mu m$ diameter basalt grains impacting a granular bed at 0.8 m/s. We find that such an impact typically leads to less than 10 particles being ejected from the granular bed, with typical ejecta trajectories rising to less than one particle diameter above the surface. That is, the observed impacts are highly dissipative and only a small fraction of the impact energy is imparted onto the ejecta. While the impactor itself still rebounds, it typically slows down significantly to an average of about 20 % of its impact velocity. Scaled to asteroids, impactor and ejecta generated from impacts of sand sized grains are not able to spread over the asteroid's surface but will stay close to the impact site. Therefore these highly inelastic impacts into soft granular beds efficiently trap grains, in contrast to more elastic impacts on bare, rocky surfaces confirming suggestions by Shinbrot (2017). This is also in agreement to observed features on asteroids as this topological elasticity bias suggests that redistribution of grains leads to a size segregation.

In an earlier work, we found that large metallic iron fractions in dust aggregates and strong magnetic fields boost preplanetary growth. This sets an initial bias for the formation of Mercury-like planets in the inner part of protoplanetary disks. We extended these experiments here by adding pure quartz aggregates to the iron-rich aggregates. Magnetic boost still leads to the formation of larger clusters of aggregates. These clusters now include silicate aggregates, which can also be connecting bridges between chains. However, at least a certain fraction of iron-rich aggregates are needed to trigger magnetic boost. Without a magnetic field, the sticking properties of the aggregates and their constituents determine the composition of clusters of a given size. This introduces a new fractionation and sorting mechanism by cluster formation at the bouncing barrier.

A planetesimal moves through the gas of its protoplanetary disc where it experiences a head wind. Though the ambient pressure is low, this wind can erode and ultimately destroy the planetesimal if the flow is strong enough. For the first time, we observe wind erosion in ground based and microgravity experiments at pressures relevant in protoplanetary discs, i.e. down to $10^{-1}\, \rm mbar$. We find that the required shear stress for erosion depends on the Knudsen number related to the grains at the surface. The critical shear stress to initiate erosion increases as particles become comparable to or larger than the mean free path of the gas molecules. This makes pebble pile planetesimals more stable at lower pressure. However, it does not save them as the experiments also show that the critical shear stress to initiate erosion is very low for sub-millimetre sized grains.

Lifting dust and sand into the thin Martian atmosphere is a challenging problem. Atmospheric pressure excursions within dust devils have been proposed to support lifting. We verify this idea in laboratory experiments. Pressure differences up to a few Pa are applied along particle layers of 50 to 400 $\rm \mu m$. As samples we used glass beads of $\sim$50 $\rm \mu m$ diameter and irregular basalt grains of $\sim$20 $\rm \mu m$ in size. The total ambient pressure of air was set to 600 Pa. Particles are ejected at pressure differences as low as 2.0 $\rm \pm$ 0.8 Pa. In the case of glass beads, the ejected grains returning to the particle bed can trigger new particle ejections as they reduce cohesion and release the tension from other grains. Therefore, few impacting grains might be sufficient to sustain dust lifting in a dust devil at even lower pressure differences. Particle lift requires a very thin, $\sim$100 $\rm \mu m$, low permeability particle layer on top of supporting ground with larger pore space. Assuming this, our experiments support the idea that pressure excursions in Martian dust devils release grains from the ground.

In laboratory experiments, we study the motion of levitated, sedimenting clouds of sub-mm grains at low ambient pressure and at high solid-to-gas ratios $\epsilon$. The experiments show a collective behavior of particles, i.e. grains in clouds settle faster than an isolated grain. In collective particle clouds, the sedimentation velocity linearly depends on $\epsilon$ and linearly depends on the particle closeness $C$. However, collective behavior only sets in at a critical value $\epsilon_{\rm crit}$ which linearly increases with the experiment Stokes number St. For $\rm St <0.003 $ particles always behave collectively. For large Stokes numbers, large solid-to-gas ratios are needed to trigger collective behavior, e.g. $\epsilon_{\rm crit} = 0.04$ at $\rm St = 0.01$. Applied to protoplanetary disks, particles in dense environments will settle faster. In balance with upward gas motions (turbulent diffusion, convection) the thickness of the midplane particle layer will be smaller than calculated based on individual grains, especially for dust. For pebbles, large solid-to-gas ratios are needed to trigger instabilities based on back-reaction.

We developed an experiment to study different aspects of granular matter under microgravity. The 1.5U small experiment was carried out on the International Space Station. About 3500 almost identical spherical glass particles with 856 um diameter were placed in a container of 50*50 mm cross section. Adjusting the height between 5 and 50 mm, the filling factor can be varied. The sample was vibrated under different frequencies and amplitudes. The majority of the data are video images of the particles motion. Here, we first give an overview of the general setup and a first qualitative account of different phenomena observed in about 700 experimental runs. These phenomena include collisional cooling, collective motion via gas-cluster coupling, and the influence of electrostatic forces on particle-particle interactions.

We carried out wind tunnel experiments on parabolic flights with 100 $\mu$m Mojave Mars simulant sand. The experiments result in shear stress thresholds and erosion rates for varying g-levels at 600 Pa pressure. Our data confirm former results on JSC Mars 1A simulant where the threshold shear stress is lower under Martian gravity than extrapolated from earlier ground-based studies which fits observations of Martian sand activity. The data are consistent with a model by Shao and Lu (2000) and can also be applied to other small terrestrial (exo)-planets with low pressure atmospheres.

Collisional growth of dust occurs in all regions of protoplanetary disks with certain materials dominating between various condensation lines. The sticking properties of the prevalent dust species depend on the specific temperatures. The inner disk is the realm of silicates spanning a wide range of temperatures from room temperature up to sublimation beyond $1500\,\mathrm{K}$. For the first time, we carried out laboratory collision experiments with hot levitated basalt dust aggregates of $1\, \rm mm$ in size. The aggregates are compact with a filling factor of $0.37 \pm 0.06$. The constituent grains have a wide size distribution that peaks at about $0.6\,\mu \mathrm{m}$. Temperatures in the experiments are varied between approximately $600\,\mathrm{K}$ and $1100\,\mathrm{K}$. Collisions are slow with velocities between $0.002\,\mathrm{m}\,\mathrm{s}^{-1}$ and $0.15\,\mathrm{m}\,\mathrm{s}^{-1}$, i.e., relevant for protoplanetary disks. Aside from variations of the coefficients of restitution due to varying collision velocities, the experiments show low sticking probability below $900\,\mathrm{K}$ and an increasing sticking probability starting at $900\,\mathrm{K}$. This implies that dust can grow to larger size in hot regions, which might change planet formation. One scenario is an enhanced probability for local planetesimal formation. Another scenario is a reduction of planetesimal formation as larger grains are more readily removed as a consequence of radial drift. However, the increased growth at high temperatures likely changes planetesimal formation one way or the other.

In the past, laboratory experiments and theoretical calculations showed a mismatch in derived sticking properties of silicates in the context of planetesimal formation. It has been proposed by Kimura et al. (2015) that this mismatch is due to the value of the surface energy assumed, supposedly correlated to the presence or lack of water layers of different thickness on a grain's surface. We present tensile strength measurements of dust aggregates with different water content here. The results are in support of the suggestion by Kimura et al. (2015). Dry samples show increased strengths by a factor of up to 10 over wet samples. A high value of $\gamma = 0.2 J/m^2$ likely applies to the dry low pressure conditions of protoplanetary disks and should be used in the future.

Collisional charging is one potential initial step in generating lightning. In this work, we study the charging of colliding monodisperse, spherical basalt grains depending on ambient pressure. We used grains of 1.0 to 1.2 mm in one set and 2.0 to 2.4 mm in another set. We varied the ambient pressure between 0.03 mbar and 80 mbar. This especially includes Martian pressure being 6 mbar on average. At a few mbar the net charge gathering on colliding grains has a minimum. A smooth incline in charging occurs for larger pressures. Toward lower pressure the charge increases steeply. The pressure dependence is in agreement to a model where the maximum charge is limited by a gas discharge occurring between two charged colliding grains shortly after or before a collision. The capability of building up charge is at a minimum exactly in the range of Martian pressures. The charges on grains are at least a factor 5 smaller than at the highest pressure tested and still smaller compared to ambient pressure on Earth. This implies that on Mars collisional charging and the potential of subsequent generation of lightning or other large scale discharges are strongly reduced compared to Earth. This might result in less frequent and less energetic lightning on Mars.

Water ice is abundant in protoplanetary disks. Its sticking properties are therefore important during phases of collisional growth. In this work, we study the sticking and rolling of 1.1 mm ice grains at different temperatures. We find a strong increase in sticking between 175 K to 200 K which levels off at higher temperatures. In terms of surface energy this is an increase with a factor of 63.4, e.g. from $\gamma = 0.0029 \rm J/m^2$ to $\gamma = \rm 0.19 J/m^2$, respectively. We also measured critical forces for inelastic rolling. The critical rolling distance is constant with a value of 0.19 mm. In view of planetesimal formation at low temperatures in protoplanetary disks, the surface energy is not larger than for silicate dust and ice aggregation will share the same shortcommings. In general, water ice has no advantage over silicates for sticking and collisional growth might not favor ice over silicates.

The streaming instability, as an example of instabilities driven by particle feedback on a gas flow, has been proven to have a major role in controlling the formation of planetesimals. Here, we present experiments to approach this situation in the laboratory for particles in the Knudsen flow regime. In these experiments, we observe a particle cloud trapped for about 30 s in a rotating system under Earth's gravity. For average dust-to-gas ratios up to 0.08, particles behave like individual test particles. Their sedimentation speed is identical to that of a single free-falling particle, even in locally denser regions. However, for higher dust-to-gas ratios, the motion of particles becomes sensitive to clumping. Particles in locally denser regions now sediment faster. Their sedimentation speed then depends linearly on the overall dust-to-gas ratio. This clearly shows a transition from tracerlike behavior to collective behavior. Beyond these findings, these types of experiments can now be used as a gauge to test the particle feedback models in astrophysical hydrocodes which are currently used for numerical simulations of streaming instabilities.

In parabolic flight experiments we studied the wind induced erosion of granular beds composed of spherical glass beads at low gravity and low ambient pressure. Varying g-levels were set by centrifugal forces. Expanding existing parameter sets to a pressure range between $p=300-1200\,$Pa and to g-levels of $g=1.1-2.2\,\rm m\,s^{-2}$ erosion thresholds are still consistent with the existing model for wind erosion on planetary surfaces by Shao & Lu (2000). These parameters were the lowest values that could technically be reached by the experiment. The experiments decrease the necessary range of extrapolation of erosion thresholds from verified to currently still unknown values at the conditions of planetesimals in protoplanetary discs. We apply our results to the stability of planetesimals. In inner regions of protoplanetary discs, pebble pile planetesimals below a certain size are not stable but will be disassembled by a head wind.

The inner part of protoplanetary disks can be threaded by strong magnetic fields. In laboratory levitation experiments, we study how magnetic fields up to 7 mT influence the aggregation of dust by observing the self-consistent collisional evolution of particle ensembles. As dust samples we use mixtures of iron and quartz in different ratios. Without magnetic fields, particles in all samples grow into a bouncing barrier. These aggregates reversibly form larger clusters in the presence of magnetic fields. The size of these clusters depends on the strength of the magnetic field and the ratio between iron and quartz. The clustering increases the size of the largest entities by a factor of a few. If planetesimal formation is sensitive to the size of the largest aggregates, e.g., relying on streaming instabilities, then planetesimals will preferentially grow iron-rich in the inner region of protoplanetary disks. This might explain the iron gradient in the solar system and the formation of dense Mercury-like planets.

In laboratory experiments, spherical 1 mm-wide glass and basalt particles are heated, and the hot particles collide at about 1m/s with a flat glass target that is at room temperature. When the particles are heated below 900 K, the collisions are essentially elastic with coefficients of restitution of about 0.9, but above 900K collisions become increasingly inelastic and the coefficient of restitution decreases with increasing temperature. At 1100K the glass particles approach sticking but, simultaneously, at the same temperature the particles melt on timescales of minutes. The basalt particles approach sticking at 1200 K. Only above 1400K do basalt grains in contact with each other fuse together, forming compounds on timescales of hours, and at 1500K basalt grains completely fuse together. Therefore, cooling basalt grains only have a 100K window for compound formation, and velocities very likely have to be below 1m/s for sticking in the first place. We predict that this puts constraints on compound chondrule formation and particle densities in the solar nebula.

Much of a planet's composition could be determined right at the onset of formation. Laboratory experiments can constrain these early steps. This includes static tensile strength measurements or collisions carried out under Earth's gravity and on various microgravity platforms. Among the variety of extrasolar planets which eventually form are (Exo)-Mercury, terrestrial planets with high density. If they form in inner protoplanetary disks, high temperature experiments are mandatory but they are still rare. Beyond the initial process of hit-and-stick collisions, some additional selective processing might be needed to explain Mercury. In analogy to icy worlds, such planets might, e.g., form in environments which are enriched in iron. This requires methods to separate iron and silicate at early stages. Photophoresis might be one viable way. Mercury and Mercury-like planets might also form due to the ferromagnetic properties of iron and mechanisms like magnetic aggregation in disk magnetic fields might become important. This review highlights some of the mechanisms with the potential to trigger Mercury formation.

Dust and sand motion are a common sight on Mars. Understanding the interaction of atmosphere and Martian soil is fundamental to describe the planet's weather, climate and surface morphology. We set up a wind tunnel to study the lift of a mixture between very fine sand and dust in a Mars simulant soil. The experiments were carried out under Martian gravity in a parabolic flight. The reduced gravity was provided by a centrifuge under external microgravity. The onset of saltation was measured for a fluid threshold shear velocity of 0.82$\pm$0.04 m/s. This is considerably lower than found under Earth gravity. In addition to a reduction in weight, this low threshold can be attributed to gravity dependent cohesive forces within the sand bed, which drop by 2/3 under Martian gravity. The new threshold for saltation leads to a simulation of the annual dust cycle with a Mars GCM that is in agreement with observations.

Dust drifting inward in protoplanetary disks is subject to increasing temperatures. In laboratory experiments, we tempered basaltic dust between 873 K and 1273 K and find that the dust grains change in size and composition. These modifications influence the outcome of self-consistent low speed aggregation experiments showing a transition temperature of 1000\,K. Dust tempered at lower temperatures grows to a maximum aggregate size of $2.02 \pm 0.06$ mm, which is $1.49 \pm 0.08$ times the value for dust tempered at higher temperatures. A similar size ratio of $1.75 \pm 0.16$ results for a different set of collision velocities. This transition temperature is in agreement with orbit temperatures deduced for observed extrasolar planets. Most terrestrial planets are observed at positions equivalent to less than 1000 K. Dust aggregation on the millimeter-scale at elevated temperatures might therefore be a key factor for terrestrial planet formation.

The tensile strength of small dusty bodies in the solar system is determined by the interaction between the composing grains. In the transition regime between small and sticky dust ($\rm \mu m$) and non cohesive large grains (mm), particles still stick to each other but are easily separated. In laboratory experiments we find that thermal creep gas flow at low ambient pressure generates an overpressure sufficient to overcome the tensile strength. For the first time it allows a direct measurement of the tensile strength of individual, very small (sub)-mm aggregates which consist of only tens of grains in the (sub)-mm size range. We traced the disintegration of aggregates by optical imaging in ground based as well as microgravity experiments and present first results for basalt, palagonite and vitreous carbon samples with up to a few hundred Pa. These measurements show that low tensile strength can be the result of building loose aggregates with compact (sub)-mm units. This is in favour of a combined cometary formation scenario by aggregation to compact aggreates and gravitational instability of these units.

In recent laboratory studies the robustness of a bouncing barrier in planetesimal formation was studied with an ensemble of preformed compact mm-sized aggregates. Here we show that a bouncing barrier indeed evolves self-consistently by hit-and-stick from an ensemble of smaller dust aggregates. In addition, we feed small aggregates to an ensemble of larger bouncing aggregates. The stickiness temporarily increases, but the final number of aggregates still bouncing remains the same. However, feeding on the small particle supply, the size of the bouncing aggregates increases. This suggests that in the presence of a dust reservoir aggregates grow into but also out of a bouncing barrier at larger size.

We consider the mechanism of photophoretic transport in protoplanetary disks that are optically thick to radiation. Here, photophoresis is not caused by the central star but by temperature fluctuations that subject suspended solid particles, including chondrules, to non-isotropic thermal radiation within the disk. These short-lived temperature fluctuations can explain time-of-flight size sorting and general number density enhancements. The same mechanism will also lead to velocity fluctuations of dust aggregates beyond $100\,\mathrm{m\,s^{-1}}$ for mm-sized particles in protoplanetary disks. Applying this in future research will change our understanding of the early phases of collisional dust evolution and aggregate growth as particles cross the bouncing barrier and as mass transfer rates are altered.

Observations of pre-transitional disks show a narrow inner dust ring and a larger outer one. They are separated by a cavity with no or only little dust. We propose an efficient recycling mechanism for the inner dust ring which keeps it in a steady-state. No major particle sources are needed for replenishment. Dust particles and pebbles drift outwards by radiation pressure and photophoresis. The pebbles grow during outward drift until they reach a balanced position where residual gravity compensates photophoresis. While still growing larger they reverse their motion and drift inwards. Eventually, their speed is fast enough that they get destroyed in collisions with other pebbles and drift outwards again. We quantify the force balance and drift velocities for the disks LkCa15 and HD135344B. We simulate single particle evolution and show that this scenario is viable. Growth and drift timescales are on the same order and a steady state can be established in the inner dust ring.

Aerosol particles experience significant photophoretic forces at low pressure. Previous work assumed the average particle temperature to be very close to the gas temperature. This might not always be the case. If the particle temperature or the thermal radiation field differs significantly from the gas temperature (optically thin gases), given approximations overestimate the photophoretic force by an order of magnitude on average with maximum errors up to more than three magnitudes. We therefore developed a new general approximation which on average only differs by 1 % from the true value.

In laboratory experiments, we studied collisions of ensembles of compact (filling factor 0.33) millimeter dust aggregates composed of micrometer quartz grains. We used cylindrical aggregates, triangular aggregates, square aggregates, and rectangular aggregates. Ensembles of equal size aggregates as well as ensembles with embedded larger aggregates were studied. The typical collision velocities are 10-20 mm $\rm s^{-1}$. High spatial and temporal resolution imaging unambiguously shows that individual collisions lead to sticking with a high probability of 20 percent. This leads to connected clusters of aggregates. The contact areas between two aggregates increase with collision velocity. However, this cluster growth is only temporary, as subsequent collisions of aggregates and clusters eventually lead to the detachment of all aggregates from a cluster. The contacts are very fragile as aggregates cannot be compressed further or fragment under our experimental conditions to enhance the contact stability. Therefore, the evolution of the ensemble always leads back to a distribution of individual aggregates of initial size. This supports and extends earlier experiments showing that a bouncing barrier in planetesimal formation would be robust against shape and size variations.

Collisions of ice particles play an important role in the formation of planetesimals and comets. In recent work we showed, that CO$_2$ ice behaves like silicates in collisions. The resulting assumption was that it should therefore stick less efficiently than H$_2$O ice. Within this paper a quantification of the latter is presented. We used the same experimental setup to study collisions of pure CO$_2$ ice, pure water ice and 50\% mixtures by mass between CO$_2$ and water at 80K, 1 mbar and an average particle size of $\sim 90 \mu$m. The results show a strong increase of the threshold velocity between sticking and bouncing with increasing water content. This supports the idea that water ice is favorable for early growth phases of planets in a zone within the H$_2$O and the CO$_2$ iceline.

Insolation of the Martian soil leads to a sub-surface overpressure due to thermal creep gas flow. This could support particle entrainment into the atmosphere. Short time shadowing e.g. by the traverse of a larger dust devil would enhance this effect. We find in microgravity experiments that mass ejection rates are increased by a factor of 10 for several seconds if a light source of 12.6 kW/$\rm m^2$ is turned off. Scaled to Mars this implies that self-shadowing of a partially opaque dust devil might lead to a strongly amplified flux of lifted material. We therefore suggest that self-shadowing might be a mechanism on Mars to increase the total dust loading of a dust devil and keep it self-sustained.

In protoplanetary disks, CO$_2$ is solid ice beyond its snow line at $\sim 10 \rm AU$. Due to its high abundance, it contributes heavily to the collisional evolution in this region of the disk. For the first time, we carried out laboratory collision experiments with CO$_2$ ice particles and a CO$_2$-covered wall at a temperature of 80 K. Collision velocities varied between 0 - 2.5 m/s. Particle sizes were on the order of $\sim$ 100 $\mu$m. We find a threshold velocity between the sticking and the bouncing regime at 0.04 m/s. Particles with greater velocities but below 1 m/s bounce off the wall. For yet greater velocities, fragmentation occurs. We give analytical models for the coefficients of restitution and fragmentation strength consistent with the experimental data. Set in context, our data show that CO$_2$ ice and silicate dust resemble each other in the collisional behavior. Compared to water ice the sticking velocity is an order of magnitude smaller. One immediate consequence as example is that water ice particles mantled by CO$_2$ ice lose any "sticking advantage." In this case, preferential planetesimal growth attributed to the sticking properties of water ice will be limited to the region between the H$_2$O ice line and the CO$_2$ ice line.

In this work we present laboratory measurements on the reduction of the threshold friction velocity necessary for lifting dust if the dust bed is illuminated. Insolation of a porous soil establishes a temperature gradient. At low ambient pressure this gradient leads to thermal creep gas flow within the soil. This flow leads to a sub-surface overpressure which supports lift imposed by wind. The wind tunnel was run with Mojave Mars Simulant and air at 3, 6 and 9 mbar, to cover most of the pressure range at martian surface levels. Our first measurements imply that the insolation of the martian surface can reduce the entrainment threshold velocity between 4 % and 19 % for the conditions sampled with our experiments. An insolation activated soil might therefore provide additional support for aeolian particle transport at low wind speeds.

The illuminated dusty surface of Mars acts like a gas pump. It is driven by thermal creep at low pressure within the soil. In the top soil layer this gas flow has to be sustained by a pressure gradient. This is equivalent to a lifting force on the dust grains. The top layer is therefore under tension which reduces the threshold wind speed for saltation. We carried out laboratory experiments to quantify the thickness of this activated layer. We use basalt with an average particle size of 67 $\mu$m. We find a depth of the active layer of 100 to 200 $\rm \mu m$. Scaled to Mars the activation will reduce threshold wind speeds for saltation by about 10%.

Photophoretic motion can transport illuminated particles in protoplanetary disks. In a previous paper we focused on the modeling of steady state photophoretic forces based on the compositions derived from tomography and heat transfer. Here, we present microgravity experiments which deviate significantly from the steady state calculations of the first paper. The experiments on average show a significantly smaller force than predicted with a large variation in absolute photophoretic force and in the direction of motion with respect to the illumination. Time-dependent modeling of photophoretic forces for heat-up and rotation show that the variations in strength and direction observed can be well explained by the particle reorientation in the limited experiment time of a drop tower experiment. In protoplanetary disks, random rotation subsides due to gas friction on short timescales and the results of our earlier paper hold. Rotation has a significant influence in short duration laboratory studies. Observing particle motion and rotation under the influence of photophoresis can be considered as a basic laboratory analog experiment to Yarkovsky and YORP effects.

For dust aggregates in protoplanetary discs a transition between sticking and bouncing in individual collisions at mm to cm size has been observed in the past. This lead to the notion of a bouncing barrier for which growth gets stalled. Here, we present long term laboratory experiments on the outcome of repeated aggregate collisions at the bouncing barrier. About 100 SiO$_2$ dust aggregates of 1 mm in size were observed interacting with each other. Collisions occured within a velocity range from below mm/s up to cm/s. Aggregates continuously interacted with each other over a period of 900 s. During this time more than $10^5$ collisions occured. Nearly 2000 collisions were analyzed in detail. No temporal stable net growth of larger aggregates was observed even though sticking collision occur. Larger ensembles of aggregates sticking together are formed but were disassembled again during the further collisional evolution. The concept of a bouncing barrier supports the formation of planetesimals by seeded collisional growth as well as by gravitational instability favouring a significant total mass being limited to certain size ranges. Within our parameter set the experiments confirm that bouncing barriers are one possible and likely evolutionary limit of a self consistent particle growth.

Dust collisions in protoplanetary disks are one means to grow planetesimals, but the destructive or constructive nature of high speed collisions is still unsettled. In laboratory experiments, we study the self-consistent evolution of a target upon continuous impacts of submm dust aggregates at collision velocities of up to 71m/s. Earlier studies analyzed individual collisions, which were more speculative for high velocities and low projectile masses. Here, we confirm earlier findings that high speed collisions result in mass gain of the target. We also quantify the accretion efficiency for the used SiO2 (quartz) dust sample. For two different average masses of dust aggregates (0.29g and 2.67g) accretion efficiencies are decreasing with velocity from 58% to 18% and from 25% to 7% at 27m/s to 71m/s, respectively. The accretion efficiency decreases approximately as logarithmic with impact energy. At the impact velocity of 49m/s the target acquires a volume filling factor of 38%. These data extend earlier work that pointed to the filling factor leveling off at 8m/s to a value of 33%. Our results imply that high speed collisions are an important mode of particle evolution. It especially allows existing large bodies to grow further by scavenging smaller aggregates with high efficiency.

Photophoresis is a physical process that transports particles in optical thin parts of protoplanetary disks, especially at the inner edge and at the optically surface. To model the transport and resulting effects in detail, it is necessary to quantify the strength of photophoresis for different particle classes as a fundamental input. Here, we explore photophoresis for a set of chondrules. The composition and surface morphology of these chondrules was measured by X-ray tomography. Based on the three-dimensional models, heat transfer through illuminated chondrules was calculated. The resulting surface temperature map was then used to calculate the photophoretic strength. We found that irregularities in particle shape and variations in composition induce variations in the photophoretic force. These depend on the orientation of a particle with respect to the light source. The variations of the absolute value of the photophoretic force on average over all chondrules is $4.17\%$. The deviation between the direction of the photophoretic force and illumination is $3.0^\circ \pm 1.5^\circ$. The average photophoretic force can be well approximated and calculated analytically assuming a homogeneous sphere with a volume equivalent mean radius and an effective thermal conductivity. We found an analytic expression for the effective thermal conductivity. The expression depends on the two main phases of a chondrule, and decreases with the amount of fine-grained devitrified, plagioclase-normative mesostasis up to factor of three. For the chondrule sample studied (Bjurb\"ole chondrite), we found a dependence of the photophoretic force on chondrule size.

Aggregation of ice particles is a fundamental process in the interstellar medium as well as in planet formation. Dedicated to study the contact physics of nm-ice particles we developed a thermal gradient force microscope. This allows us and was used to measure pull-off forces with a resolution on the nN-scale and to measure rolling. Furthermore, based on a free probe, it also allows us to study twisting torques for the first time. The experiments show that torques required to twist are significantly larger than that macroscopic models scaled down to the nm-size range would predict. This implies that (ice) aggregates in astrophysical settings with small constituents are more robust against restructuring than previously thought. They likely grow as fractal aggregates to larger size before they restructure and during later compact growth they likely retain a higher porosity during further evolution towards planetesimals.

In optically thin parts of protoplanetary disks photophoresis is a significant force not just for dust grains, but also for macroscopic bodies. The absolute strength on the supposedly highly porous objects is not known in detail as yet. We set up a low pressure torsion balance and studied photophoretic forces. We investigated the dependence on plate dimensions and on ambient pressure and considered the influence of channels through the plates. As samples for full (no channel) plates we used tissue with 2mm thickness and circular shape with diameters of 10mm, 30mm and 50mm. The influence of channels was probed on rectangular-shaped circuit boards of 35mm x 35mm area and 1.5mm thickness. The number of channels was 169 and 352. At low pressure, the absolute photophoretic force is proportional to the cross section of the plates. At high pressure, gas flow through the channels enhances the photophoretic force. The pressure dependence of the radiative force can (formally) be calculated by photophoresis on particles with a characteristic length. We derived two characteristic length scales l depending on the plate radius r_1, the channel radius r_2, and the thickness of the plate which equals the length of the channel d as l=r^{0.35} x d^{0.65}. The highest force is found at a pressure p_max = 15 x l^{-1}Pa mm. In total, the photophoretic force on a plate with channels can be well described by a superposition of the two components: photophoresis due to the overall size and cross section of the plate and photophoresis due to the channels, both with their characteristic pressure dependencies. We applied these results to the transport of large solids in protoplanetary disks and found that the influence of porosity on the photophoretic force can reverse the inward drift of large solids, for instance meter-sized bodies, and push them outward within the optically thin parts of the disk.

At the inner edge of a protoplanetary disk solids are illuminated by stellar light. This illumination heats the solids and creates temperature gradients along their surfaces. Interactions with ambient gas molecules lead to a radial net gas flow. Every illuminated solid particle within the edge is an individual small gas pump transporting gas inward. In total the inner edge can provide local mass flow rates as high as $\dot{M} = 10^{-5} M_{\odot}$ yr$^{-1}$.

Mercury's high uncompressed mass density suggests that the planet is largely composed of iron, either bound within metal (mainly Fe-Ni), or iron sulfide. Recent results from the MESSENGER mission to Mercury imply a low temperature history of the planet which questions the standard formation models of impact mantle stripping or evaporation to explain the high metal content. Like Mercury, the two smallest extrasolar rocky planets with mass and size determination, CoRoT-7b and Kepler-10b, were found to be of high density. As they orbit close to their host stars this indicates that iron rich inner planets might not be a nuisance of the solar system but be part of a general scheme of planet formation. From undifferentiated chondrites it is also known that the metal to silicate ratio is highly variable which must be ascribed to pre-planetary fractionation processes. Due to this fractionation most chondritic parent bodies - most of them originated in the asteroid belt - are depleted in iron relative to average solar system abundances. The astrophysical processes leading to metal silicate fractionation in the solar nebula are essentially unknown. Here, we consider photophoretic forces. As these forces particularly act on irradiated solids, they might play a significant role for the composition of planetesimals forming at the inner edge of protoplanetary discs. Photophoresis can separate high thermal conductivity materials (iron) from lower thermal conductivity solids (silicate). We suggest that the silicates are preferentially pushed into the optical thick disk. Subsequent planetesimal formation at the edge moving outwards leads to metal rich planetesimals close to the star and metal depleted planetesimals further out in the nebula.

Transporting solids of different sizes is an essential process in the evolution of protoplanetary disks and planet formation. Large solids are supposed to drift inward; high-temperature minerals found in comets are assumed to have been transported outward. From low-gravity experiments on parabolic flights we studied the light-induced erosion of dusty bodies caused by a solid-state greenhouse effect and photophoresis within a dust bed's upper layers. The gravity levels studied were 0.16g, 0.38g, 1g, and 1.7g. The light flux during the experiments was 12 +/- 2 kW/m^2 and the ambient pressure was 6 +/- 0.9 mbar. Light-induced erosion is strongly gravity dependent, which is in agreement with a developed model. In particular for small dusty bodies ((sub)-planetesimals), efficient erosion is possible at the optically thin inner edges of protoplanetary disks. Light-induced erosion prevents significant parts of a larger body from moving too close to the host star and be being subsequently accreted. The small dust produced continues to be subject to photophoresis and is partially transported upward and outward over the surface of the disk; the resulting small dust particles observed over the disk's lifetime. The fraction of eroded dust participates in subsequent cycles of growth during planetesimal formation. Another fraction of dust might be collected by a body of planetary size if this body is already present close to the disk edge. Either way, light induced erosion is an efficient recycling process in protoplanetary disks.

Many chondrules are found to be surrounded by a fine grained rim. Supposedly, these rims were acquired from dust accreted to the chondrules in a protoplanetary disk. In numerical simulations we study the heat transfer in illuminated bare and dust mantled chondrules. The calculations consider the chondrule size, the dust mantle size, and the thermal conductivities of both components as parameters. We calculate the photophoretic force and compare the numerical results to analytical approximations. We give an expression to quantify the photophoretic force on a spherical particle in the free molecular regime to better than 2%. We describe the influence of a dust mantle on the photophoretic strength by an effective thermal conductivity of the core-mantle particle. The effective thermal conductivity significantly depends on the size ratio between mantle and chondrule but not on the absolute sizes. It also strongly depends on the thermal conductivity of the mantle with minor influence of the thermal conductivity of the chondrule. The size ratio between rim and chondrule in meteorites is found to vary systematically with overall size by other authors. Based on this, our calculations show that a photophoretic size sorting can occur for dust mantled chondrules in optically thin disks or at the evolving inner edge of the solar nebula.

The first macroscopic bodies in protoplanetary disks are dust aggregates. We report on a number of experimental studies with dust aggregates formed from micron-size quartz grains. We confirm in laboratory collision experiments an earlier finding that producing macroscopic bodies by the random impact of sub-mm aggregates results in a well-defined upper-filling factor of 0.31 \pm 0.01. Compared to earlier experiments, we increase the projectile mass by about a factor of 100. The collision experiments also show that a highly porous dust-aggregate can retain its highly porous core if collisions get more energetic and a denser shell forms on top of the porous core. We measure the mechanical properties of cm-sized dust samples of different filling factors between 0.34 and 0.50. The tensile strength measured by a Brazilian test, varies between 1 kPa and 6 kPa. The sound speed is determined by a runtime measurement to range between 80 m/s and 140 m/s while Young's modulus is derived from the sound speed and varies between 7MPa and 25MPa. The samples were also subjected to quasi-static omni- and uni-directional compression todetermine their compression strengths and flow functions. Applied to planet formation, our experiments provide basic data for future simulations, explain the specific collisional outcomes observed in earlier experiments, and in general support a scenario where collisional growth of planetesimals is possible.

Collisions of mm-size dust aggregates play a crucial role in the early phases of planet formation. We developed a laboratory setup to observe collisions of dust aggregates levitating at mbar pressures and elevated temperatures of 800 K. We report on collisions between basalt dust aggregates of from 0.3 to 5 mm in size at velocities between 0.1 and 15 cm/s. Individual grains are smaller than 25 \mum in size. We find that for all impact energies in the studied range sticking occurs at a probability of 32.1 \pm 2.5% on average. In general, the sticking probability decreases with increasing impact parameter. The sticking probability increases with energy density (impact energy per contact area). We also observe collisions of aggregates that were formed by a previous sticking of two larger aggregates. Partners of these aggregates can be detached by a second collision with a probability of on average 19.8 \pm 4.0%. The measured accretion efficiencies are remarkably high compared to other experimental results. We attribute this to the rel. large dust grains used in our experiments, which make aggregates more susceptible to restructuring and energy dissipation. Collisional hardening by compaction might not occur as the aggregates are already very compact with only 54 \pm 1% porosity. The disassembly of previously grown aggregates in collisions might stall further aggregate growth. However, owing to the levitation technique and the limited data statistics, no conclusive statement about this aspect can yet be given. We find that the detachment efficiency decreases with increasing velocities and accretion dominates in the higher velocity range. For high accretion efficiencies, our experiments suggest that continued growth in the mm-range with larger constituent grains would be a viable way to produce larger aggregates, which might in turn form the seeds to proceed to growing planetesimals.

Small (sub)-micron dust is present over the entire lifetime of protoplanetary disks. As aggregation readily depletes small particles, one explanation might be that dust is continuously generated by larger bodies in the midplane and transported to the surface of the disks. In general, in a first step of this scenario, the larger bodies have to be destroyed again and different mechanisms exist with the potential to accomplish this. Possible destructive mechanisms are fragmentation in collisions, erosion by gas drag or light induced erosion. In laboratory experiments we find that the latter, light induced erosion by Knudsen compression and photophoresis, can provide small particles. It might be a preferred candidate as the dust is released into a low particle density region. The working principle of this mechanism prevents or decreases the likelihood for instant re-accretion or re-growth of large dense aggregates. Provided that there is a particle lift, e.g. turbulence, these particles might readily reach the surface of the disk.

In a laboratory experiment, water-ice aggregates are trapped in a vacuum chamber at a pressure of 2 mbar due to photophoresis and thermophoresis. The particles are located between a Peltier element at the bottom at 250 K and a reservoir of liquid nitrogen at the top at 77 K. Particle sizes vary between 20 micrometres and a few hundred micrometres. It is found that 95% of all the particles rotate about their vertical axis. A qualitative model is developed which explains why particles should mainly align to and rotate around the vertical. The results imply that rotation does not decrease the vertical strength of photophoretically driven motion in, e.g., protoplanetary discs.

Aggregation of dust through sticking collisions is the first step of planet formation. Basic physical properties of the evolving dust aggregates strongly depend on the porosity of the aggregates, e.g. mechanical strength, thermal conductivity, gas-grain coupling time. Also the outcome of further collisions depends on the porosity of the colliding aggregates. In laboratory experiments we study the growth of large aggregates of $\sim$ 3 mm to 3 cm through continuous impacts of small dust agglomerates of 100 $\mu$m size, consisting of $\mu$m grains at different impact velocities. The experiments show that agglomerates grow by direct sticking as well as gravitational reaccretion. The latter can be regarded as suitable analog to reaccretion of fragments by gas drag in protoplanetary disks. Experiments were carried out in the velocity range between 1.5 m/s and 7 m/s. With increasing impact velocities the volume filling factor of the resulting agglomerates increases from $\phi = 0.2$ for 1.5 m/s to $\phi = 0.32$ for 7 m/s. These values are independent of the target size. Extrapolation of the measured velocity dependence of the volume filling factor implies that higher collision velocities will not lead to more compact aggregates. Therefore, $\phi = 0.32$ marks a degree of compaction suitable to describe structures forming at $\rm v > 6\, m/s$. At small collision velocities below 1 m/s highly porous structures with $\phi \approx 0.10$ will form. For intermediate collision velocities porosities vary. Depending on the disk model and resulting relative velocities, objects in protoplanetary disks up to dm-size might evolve from highly porous ($\phi \approx 0.10$) to compact ($\phi = 0.32$) with a more complex intermediate size range of varying porosity.

We have examined the influence of impact angle in collisions between small dust aggregates and larger dust targets through laboratory experiments. Targets consisted of \mum-sized quartz dust and had a porosity of about 67%; the projectiles, between 1 and 5 mm in diameter, were slightly more compact (64% porosity). The collision velocity was centered at 20 m/s and impact angles range from 0{\deg} to 45{\deg}. At a given impact angle, the target gained mass for projectiles smaller than a threshold size, which decreases with increasing angle from about 3 mm to 1 mm. The fact that growth is possible up to the largest angles studied supports the idea of planetesimal formation by sweep-up of small dust aggregates.

The growth of planetesimals is an essential step in planet formation. Decimetre-size dust agglomerates mark a transition point in this growth process. In laboratory experiments we simulated the formation, evolution, and properties of decimetre-scale dusty bodies in protoplanetary discs. Small sub-mm size dust aggregates consisting of micron-size SiO$_2$ particles randomly interacted with dust targets of varying initial conditions in a continuous sequence of independent collisions. Impact velocities were 7.7 m/s on average and in the range expected for collisions with decimetre bodies in protoplanetary discs. The targets all evolved by forming dust \emph{crusts} with up to several cm thickness and a unique filling factor of 31% $\pm$3%. A part of the projectiles sticks directly. In addition, some projectile fragments slowly return to the target by gravity. All initially porous parts of the surface, i.e. built from the slowly returning fragments, are compacted and firmly attached to the underlying dust layers by the subsequent impacts. Growth is possible at impact angles from 0$^{\circ}$ (central collision) to 70$^{\circ}$. No growth occurs at steeper dust surfaces. We measured the velocity, angle, and size distribution of collision fragments. The average restitution coefficient is 3.8% or 0.29 m/s ejection velocity. Ejecta sizes are comparable to the projectile sizes. The high filling factor is close to the most compact configuration of dust aggregates by local compression ($\sim 33$%). This implies that the history of the surface formation and target growth is completely erased. In view of this, the filling factor of 31% seems to be a universal value in the collision experiments of all self-consistently evolving targets at the given impact velocities. We suggest that decimetre and probably larger bodies can simply be characterised by one single filling factor.

Recently Saito & Sirono (2011) proposed that large ice aggregates which drift in- wards in protoplanetary disks break up during sublimation, ejecting embedded silicate particles. This would lead to a concentration of small solid particles close to the snow- line. In view of this model we carried out laboratory experiments where we observed freely levitating ice aggregates sublimating. We find that frequent break up is indeed very common. Scaled to a 10 cm aggregate about 2x10^4 small silicate aggregates might result. This supports the idea that sublimation of drifting ice aggregates might locally increase the density of small dust (silicate) particles which might more easily be swept up by larger dust aggregates or trigger gravitational instability. Either way this might locally boost the formation of planetesimals at the snowline.

Hot temperature minerals have been detected in a large number of comets and were also identified in the samples of Comet Wild 2 that were returned by the Stardust mission. Meanwhile, observations of the distribution of hot minerals in young stellar systems suggest that these materials were produced in the inner part of the primordial nebula and have been transported outward in the formation zone of comets. We investigate the possibility that photophoresis provides a viable mechanism to transport high-temperature materials from the inner solar system to the regions in which the comets were forming. We use a grid of time-dependent disk models of the solar nebula to quantify the distance range at which hot minerals can be transported from the inner part of the disk toward its outer regions as a function of their size and density. The particles considered here are in the form of aggregates that presumably were assembled from hot mineral individual grains ranging down to submicron sizes and formed by condensation within the hottest portion of the solar nebula. Our particle-transport model includes the photophoresis, radiation pressure, and gas drag. Depending on the postulated disk parameters and the density of particles, 10-2 to 10-1 m aggregates can reach heliocentric distances up to 35 AU in the primordial nebula over very short timescales (no more than a few hundred thousand years). 10-3 m particles follow the same trajectory as the larger ones but their maximum migration distance does not exceed 26 AU and is reached at later epochs in the disks. On the other hand, 10-5 to 10-4 m aggregates are continuously pushed outward during the evolution of the solar nebula. Our simulations suggest that irrespective of the employed solar nebula model, photophoresis is a mechanism that can explain the presence of hot temperature minerals in the formation region of comets.

Collisions between centimeter- to decimeter-sized dusty bodies are important to understand the mechanisms leading to the formation of planetesimals. We thus performed laboratory experiments to study the collisional behavior of dust aggregates in this size range at velocities below and around the fragmentation threshold. We developed two independent experimental setups with the same goal to study the effects of bouncing, fragmentation, and mass transfer in free particle-particle collisions. The first setup is an evacuated drop tower with a free-fall height of 1.5 m, providing us with 0.56 s of microgravity time so that we observed collisions with velocities between 8 mm/s and 2 m/s. The second setup is designed to study the effect of partial fragmentation (when only one of the two aggregates is destroyed) and mass transfer in more detail. It allows for the measurement of the accretion efficiency as the samples are safely recovered after the encounter. Our results are that for very low velocities we found bouncing as could be expected while the fragmentation velocity of 20 cm/s was significantly lower than expected. We present the critical energy for disruptive collisions Q*, which showed up to be at least two orders of magnitude lower than previous experiments in the literature. In the wide range between bouncing and disruptive collisions, only one of the samples fragmented in the encounter while the other gained mass. The accretion efficiency in the order of a few percent of the particle's mass is depending on the impact velocity and the sample porosity. Our results will have consequences for dust evolution models in protoplanetary disks as well as for the strength of large, porous planetesimal bodies.

Laboratory experiments show that dusty bodies in a gaseous environment eject dust particles if they are illuminated. We find that even more intense dust eruptions occur when the light source is turned off. We attribute this to a compression of gas by thermal creep in response to the changing temperature gradients in the top dust layers. The effect is studied at a light flux of 13 kW/(m*m) and 1 mbar ambient pressure. The effect is applicable to protoplanetary disks and Mars. In the inner part of protoplanetary disks, planetesimals can be eroded especially at the terminator of a rotating body. This leads to the production of dust which can then be transported towards the disk edges or the outer disk regions. The generated dust might constitute a significant fraction of the warm dust observed in extrasolar protoplanetary disks. We estimate erosion rates of about 1 kg/s for 100 m parent bodies. The dust might also contribute to subsequent planetary growth in different locations or on existing protoplanets which are large enough not to be susceptible to particle loss by light induced ejection. Due to the ejections, planetesimals and smaller bodies will be accelerated or decelerated and drift outward or inward, respectively. The effect might also explain the entrainment of dust in dust devils on Mars, especially at high altitudes where gas drag alone might not be sufficient.

In a set of 16 drop tower experiments the motion of sub-mm to mm-sized particles under microgravity was observed. Illumination by a halogen lamp induced acceleration of the particles due to photophoresis. Photophoresis on dust-free chondrules, on chondrules, glass spheres and metal spheres covered with SiC dust and on pure SiC dust aggregates was studied. This is the first time that photophoretic motion of mm-sized particles has been studied experimentally. The absolute values for the photophoretic force are consistent with theoretical expectations for spherical particles. The strength of the photophoretic force varies for chondrules, dust covered particles and pure dust from low to strong, respectively. The measurements support the idea that photophoresis in the early Solar System can be efficient to transport solid particles outward.

In laboratory experiments we determine the mass gain and loss in central collisions between cm to dm-size SiO2 dust targets and sub-mm to cm-size SiO2 dust projectiles of varying mass, size, shape, and at different collision velocities up to ~56.5 m/s. Dust projectiles much larger than 1 mm lead to a small amount of erosion of the target but decimetre targets do not break up. Collisions produce ejecta which are smaller than the incoming projectile. Projectiles smaller than 1 mm are accreted by a target even at the highest collision velocities. This implies that net accretion of decimetre and larger bodies is possible. Independent of the original size of a projectile considered, after several collisions all fragments will be of sub-mm size which might then be (re)-accreted in the next collision with a larger body. The experimental data suggest that collisional growth through fragmentation and reaccretion is a viable mechanism to form planetesimals.

Laboratory experiments show that a solid-state greenhouse effect in combination with thermophoresis can efficiently erode a dust bed in a low-pressure gaseous environment. The surface of an illuminated, light absorbing dusty body is cooler than the dust below the surface (solidstate greenhouse effect). This temperature gradient leads to a directed momentum transfer between gas and dust particles and the dust particles are subject to a force towards the surface(thermophoresis). If the thermophoretic force is stronger than gravity and cohesion, dust particles are ejected. Applied to protoplanetary discs, dusty bodies smaller than several kilometres in size which are closer to a star than about 0.4 au are subject to a rapid and complete disassembly to submillimetre size dust aggregates by this process. While an inward-drifting dusty body is destroyed, the generated dust is not lost for the disc by sublimation or subsequent accretion on to the star but can be reprocessed by photophoresis or radiation pressure. Planetesimals cannot originate through aggregation of dust inside the erosion zone. If objects larger than several kilometres already exist, they prevail and further grow by collecting dust from disassembled smaller bodies. The pile-up of solids in a confined inner region of the disc, in general, boosts the formation of planets. Erosion is possible in even strongly gas-depleted inner regions as observed for TW Hya. Reprocessing of dust through light-induced erosion offers one possible explanation for growth of large cores of gas-poor giant planets in a gas-starved region as recently found around HD 149026b.

Protoplanetary disks start their lives with a dust free inner region where the temperatures are higher than the sublimation temperature of solids. As the star illuminates the innermost particles, which are immersed in gas at the sublimation edge, these particles are subject to a photophoretic force. We examine the motion of dust particles at the inner edge of protoplanetary disks due to photophoretic drag. We find that, in a laminar disk, photophoretic drag increases the size of the inner hole after accretion onto the central body has become subdued. This region within the hole becomes an optically transparent zone containing gas and large dusty particles (>>10 cm), but devoid of, or strongly depleted in, smaller dust aggregates. Photophoresis can clear the inner disk of dust out to 10 AU in less than 1 Myr. At late times, the edge reaches a stable equilibrium between inward drift and photophoretic outward drift, at a distance of some tens of AU. Eventually, the edge will move inwards again as the disk disperses, shifting the equilibrium position back from about 40 AU to below 30 AU in 1-2 Myr in the disk model. In a turbulent disk, diffusion can delay the clearing of a disk by photophoresis. Smaller and/or age-independent holes of radii of a few AU are also possible outcomes of turbulent diffusion counteracting photophoresis. This outward and then inward moving edge marks a region of high dust concentration. This density enhancement, and the efficient transport of particles from close to the star to large distances away, can explain features of comets such as high measured ratios of crystalline to amorphous silicates, and has a large number of other applications.

We discuss the results of laboratory measurements and theoretical models concerning the aggregation of dust in protoplanetary disks, as the initial step toward planet formation. Small particles easily stick when they collide and form aggregates with an open, often fractal structure, depending on the growth process. Larger particles are still expected to grow at collision velocities of about 1m/s. Experiments also show that, after an intermezzo of destructive velocities, high collision velocities above 10m/s on porous materials again lead to net growth of the target. Considerations of dust-gas interactions show that collision velocities for particles not too different in surface-to-mass ratio remain limited up to sizes about 1m, and growth seems to be guaranteed to reach these sizes quickly and easily. For meter sizes, coupling to nebula turbulence makes destructive processes more likely. Global aggregation models show that in a turbulent nebula, small particles are swept up too fast to be consistent with observations of disks. An extended phase may therefore exist in the nebula during which the small particle component is kept alive through collisions driven by turbulence which frustrates growth to planetesimals until conditions are more favorable for one or more reasons.