This paper deals with the calibration of the analogue chains of a Square Kilometre Array (SKA) phased aperture array station, using embedded element patterns (one per antenna in the array, thus accounting for the full effects of mutual coupling) or average element patterns to generate model visibilities. The array is composed of 256 log-periodic dipole array antennas. A simulator capable of generating such per-baseline model visibility correlation matrices was implemented, which allowed for a direct comparison of calibration results using StEFCal (Statistically Efficient and Fast Calibration) with both pattern types. Calibrating the array with StEFCal using simulator-generated model visibilities was successful and thus constitutes a possible routine for calibration of an SKA phase aperture array station. In addition, results indicate that there was no significant advantage in calibrating with embedded element patterns, with StEFCal successfully retrieving similar per-element coefficients with model visibilities generated with either pattern type. This can be of significant importance for mitigating computational costs for calibration, particularly for the consideration of real-time calibration strategies. Data from the AAVS-1 (Aperture Array Verification System 1) prototype station in Western Australia was used for demonstration purposes.

This paper presents a framework to compute the receiver noise temperature (Trcv) of two low-frequency radio telescopes, the Murchison Widefield Array (MWA) and the Engineering Development Array (EDA). The MWA was selected because it is the only operational low-frequency Square Kilometre Array (SKA) precursor at the Murchison Radio-astronomy Observatory, while the EDA was selected because it mimics the proposed SKA-Low station size and configuration. It will demonstrated that the use of an existing power wave based framework for noise characterization of multiport amplifiers is sufficiently general to evaluate Trcv of phased arrays. The calculation of Trcv was done using a combination of measured noise parameters of the low-noise amplifier (LNA) and simulated S-parameters of the arrays. The calculated values were compared to measured results obtained via astronomical observation and both results are found to be in agreement. Such verification is lacking in current literature. It was shown that the receiver noise temperatures of both arrays are lower when compared to a single isolated element. This is caused by the increase in mutual coupling within the array which is discussed in depth in this paper.

We compute the spherically-averaged power spectrum from four seasons of data obtained for the Epoch of Reionisation (EoR) project observed with the Murchison Widefield Array (MWA). We measure the EoR power spectrum over $k= 0.07-3.0~h$Mpc$^{-1}$ at redshifts $z=6.5-8.7$. The largest aggregation of 110 hours on EoR0 high-band (3,340 observations), yields a lowest measurement of (43~mK)$^2$ = 1.8$\times$10$^3$ mK$^2$ at $k$=0.14~$h$Mpc$^{-1}$ and $z=6.5$ (2$\sigma$ thermal noise plus sample variance). Using the Real-Time System to calibrate and the CHIPS pipeline to estimate power spectra, we select the best observations from the central five pointings within the 2013--2016 observing seasons, observing three independent fields and in two frequency bands. This yields 13,591 2-minute snapshots (453 hours), based on a quality assurance metric that measures ionospheric activity. We perform another cut to remove poorly-calibrated data, based on power in the foreground-dominated and EoR-dominated regions of the two-dimensional power spectrum, reducing the set to 12,569 observations (419 hours). These data are processed in groups of 20 observations, to retain the capacity to identify poor data, and used to analyse the evolution and structure of the data over field, frequency, and data quality. We subsequently choose the cleanest 8,935 observations (298 hours of data) to form integrated power spectra over the different fields, pointings and redshift ranges.

We provide the first in situ measurements of antenna element (tile) beam shapes of the Murchison Widefield Array (MWA), a low radio-frequency interferometer and an SKA precursor. Most current MWA processing pipelines use an assumed beam shape, errors in which can cause absolute and relative flux density errors, as well as polarisation 'leakage'. This makes understanding the primary beam of paramount importance, especially for sensitive experiments such as a measurement of the 21 cm line from the epoch of reionisation (EoR). The calibration requirements for measuring the EoR 21 cm line are so extreme that tile to tile beam variations may affect our ability to make a detection. Measuring the primary beam shape from visibilities alone is challenging, as multiple instrumental, atmospheric, and astrophysical factors contribute to uncertainties in the data. Building on the methods of Neben et al. (2015), we tap directly into the receiving elements of the MWA before any digitisation or correlation of the signal. Using ORBCOMM satellite passes we are able to produce all-sky maps for 4 separate tiles in the XX polarisation. We find good agreement with the cutting-edge 'fully' embedded element (FEE) model of Sokolowski et al. (2017), and observe that the MWA beamformers consistently recreate beam shapes to within ~1dB in the reliable areas of our beam maps. We also clearly observe the effects of a missing dipole from a tile in one of our beam maps, and show that the FEE model is able to reproduce this modified beam shape. We end by motivating and outlining additional onsite experiments to further constrain the primary beam behaviour.

We present two methods for measuring the noise temperature of a differential input single-ended output (DISO) Low-Noise Amplifier (LNA) connected to an antenna. The first method is direct measurement of the DISO LNA and antenna in an anechoic chamber at ambient temperature. The second is a simple and low-cost noise parameter extraction of the DISO device using a coaxial long cable. The reconstruction of the DISO noise parameter from the noise wave measurements of the DISO LNA with one terminated input port is discussed in detail. We successfully applied these methods to the Murchison Widefield Array LNA and antenna.

The Murchison Widefield Array (MWA), located in Western Australia, is one of the low-frequency precursors of the international Square Kilometre Array (SKA) project. In addition to pursuing its own ambitious science program, it is also a testbed for wide range of future SKA activities ranging from hardware, software to data analysis. The key science programs for the MWA and SKA require very high dynamic ranges, which challenges calibration and imaging systems. Correct calibration of the instrument and accurate measurements of source flux densities and polarisations require precise characterisation of the telescope's primary beam. Recent results from the MWA GaLactic Extragalactic All-sky MWA (GLEAM) survey show that the previously implemented Average Embedded Element (AEE) model still leaves residual polarisations errors of up to 10-20 % in Stokes Q. We present a new simulation-based Full Embedded Element (FEE) model which is the most rigorous realisation yet of the MWA's primary beam model. It enables efficient calculation of the MWA beam response in arbitrary directions without necessity of spatial interpolation. In the new model, every dipole in the MWA tile (4 x 4 bow-tie dipoles) is simulated separately, taking into account all mutual coupling, ground screen and soil effects, and therefore accounts for the different properties of the individual dipoles within a tile. We have applied the FEE beam model to GLEAM observations at 200 - 231 MHz and used false Stokes parameter leakage as a metric to compare the models. We have determined that the FEE model reduced the magnitude and declination-dependent behaviour of false polarisation in Stokes Q and V while retaining low levels of false polarisation in Stokes U.

We describe the design and performance of the Engineering Development Array (EDA), which is a low frequency radio telescope comprising 256 dual-polarisation dipole antennas working as a phased-array. The EDA was conceived of, developed, and deployed in just 18 months via re-use of Square Kilometre Array (SKA) precursor technology and expertise, specifically from the Murchison Widefield Array (MWA) radio telescope. Using drift scans and a model for the sky brightness temperature at low frequencies, we have derived the EDA's receiver temperature as a function of frequency. The EDA is shown to be sky-noise limited over most of the frequency range measured between 60 and 240 MHz. By using the EDA in interferometric mode with the MWA, we used calibrated visibilities to measure the absolute sensitivity of the array. The measured array sensitivity matches very well with a model based on the array layout and measured receiver temperature. The results demonstrate the practicality and feasibility of using MWA-style precursor technology for SKA-scale stations. The modular architecture of the EDA allows upgrades to the array to be rolled out in a staged approach. Future improvements to the EDA include replacing the second stage beamformer with a fully digital system, and to transition to using RF-over-fibre for the signal output from first stage beamformers.

Radio interferometry most commonly involves antennas or antenna arrays of identical design. The identical antenna assumption leads to a convenient and useful mathematical simplification resulting in a scalar problem. An interesting variant to this is a "hybrid" interferometer involving two designs. We encounter this in the characterization of low-frequency antenna/array prototypes using a homogenous low-frequency array telescope such as the Murchison Widefield Array (MWA). In this work, we present an interferometry equation that applies to hybrid antennas. The resulting equation involves vector inner products rather than scalar multiplications. We discuss physical interpretation and useful applications of this concept in the areas of sensitivity measurement and calibration of an antenna/array under test using a compact calibrator source.