Twenty-four years after the discoveries of the first exoplanets, the radial-velocity (RV) method is still one of the most productive techniques to detect and confirm exoplanets. But stellar magnetic activity can induce RV variations large enough to make it difficult to disentangle planet signals from the stellar noise. In this context, HD41248 is an interesting planet-host candidate, with RV observations plagued by activity-induced signals. We report on ESPRESSO observations of HD41248 and analyse them together with previous observations from HARPS with the goal of evaluating the presence of orbiting planets. Using different noise models within a general Bayesian framework designed for planet detection in RV data, we test the significance of the various signals present in the HD41248 dataset. We use Gaussian processes as well as a first-order moving average component to try to correct for activity-induced signals. At the same time, we analyse photometry from the TESS mission, searching for transits and rotational modulation in the light curve. The number of significantly detected Keplerian signals depends on the noise model employed, which can range from 0 with the Gaussian process model to 3 with a white noise model. We find that the Gaussian process alone can explain the RV data while allowing for the stellar rotation period and active region evolution timescale to be constrained. The rotation period estimated from the RVs agrees with the value determined from the TESS light curve. Based on the data that is currently available, we conclude that the RV variations of HD41248 can be explained by stellar activity (using the Gaussian process model) in line with the evidence from activity indicators and the TESS photometry.

Mass and radius are two fundamental properties for characterising exoplanets, but only for a relatively small fraction of exoplanets are they both available. Mass is often derived from radial velocity measurements, while the radius is almost always measured using the transit method. For a large number of exoplanets, either the radius or the mass is unknown, while the host star has been characterised. Several mass-radius relations that are dependent on the planet's type have been published that often allow us to predict the radius. Our goal is to derive the radius of exoplanets using only observables extracted from spectra used primarily to determine radial velocities and spectral parameters. Our objective is to obtain a mass-radius relation independent of the planet's type. We worked with a database of confirmed exoplanets with known radii and masses, as well as the planets from our Solar System. Using random forests, a machine learning algorithm, we computed the radius of exoplanets and compared the results to the published radii. Our code, Bem, is available online. The estimated radii reproduces the spread in radius found for high mass planets better than previous mass-radius relations. The average radius error is 1.8 $R_{\oplus}$ across the whole range of radii from 1-22 $R_{\oplus}$. We find that a random forest algorithm is able to derive reliable radii, especially for planets between 4 $R_{\oplus}$ and 20 $R_{\oplus}$ for which the error is under 25$\%$. The algorithm has a low bias yet a high variance, which could be reduced by limiting the growth of the forest, or adding more data. The random forest algorithm is a promising method for deriving exoplanet properties. We show that the exoplanet's mass and equilibrium temperature are the relevant properties that constrain the radius, and do so with higher accuracy than the previous methods.

The determination of stellar effective temperature ($T_{\mathrm{eff}}$) in F, G, and K stars using H$\alpha$ profile fitting is a quite remarkable and powerful tool, because it practically does not depend on other atmospheric parameters and reddening. Nevertheless, this technique is not frequently used because of the complex procedure to recover the profile of broad lines in echelle spectra. As a consequence, tests performed on different models have sometimes provided ambiguous results. We have developed a normalization method for recovering undistorted H$\alpha$ profiles and we have first applied it to spectra acquired with the single order instrument at do Pico dos Dias Observatory to avoid the problem of blaze correction. The continuum location is optimized using an iterative procedure, where the identification of minute telluric features is performed. A set of spectra was acquired with the MUSICOS echelle spectrograph ($R = 40~000$) to independently validate the normalization method. The accuracy of the method and of the 1D + LTE model is determined using coud\'{e}/HARPS/MUSICOS spectra of the Sun and a sample of 10 Gaia Benchmark Stars with effective temperature determined from interferometric measurements. We find that the most used solar atlases cannot be used as templates for H$\alpha$ temperature diagnostics without renormalization. The comparison with the Sun shows that $T_{\mathrm{eff}}$ derived with H$\alpha$ profiles from 1D + LTE models underestimate the solar effective temperature by 28 K. Interferometry and Infrared Flux Method show a dependency on metallicity according to the relation $T_{\mathrm{eff}} = T_{\mathrm{eff}}^{H\alpha}$ $-159$[Fe/H] + 28 K within the metallicity range $-0.7$ to $+0.45$ dex. We find 3D models largely improve the agreement with the interferometric and Infrared Flux Method measurements.

Context. The atmospheric absorption of the Earth is an important limiting factor for ground-based spectroscopic observations and the near-infrared and infrared regions are the most affected. Several software packages that produce a synthetic atmospheric transmission spectrum have been developed to correct for the telluric absorption; these are Molecfit, TelFit, and TAPAS. Aims. Our goal is to compare the correction achieved using these three telluric correction packages and the division by a telluric standard star. We want to evaluate the best method to correct near-infrared high-resolution spectra as well as the limitations of each software package and methodology. Methods. We applied the telluric correction methods to CRIRES archival data taken in the J and K bands. We explored how the achieved correction level varies depending on the atmospheric T-P profile used in the modelling, the depth of the atmospheric lines, and the molecules creating the absorption. Results. We found that the Molecfit and TelFit corrections lead to smaller residuals for the water lines. The standard star method corrects best the oxygen lines. The Molecfit package and the standard star method corrections result in global offsets always below 0.5% for all lines; the offset is similar with TelFit and TAPAS for the H2O lines and around 1% for the O2 lines. All methods and software packages result in a scatter between 3% and 7% inside the telluric lines. The use of a tailored atmospheric profile for the observatory leads to a scatter two times smaller, and the correction level improves with lower values of precipitable water vapour. Conclusions. The synthetic transmission methods lead to an improved correction compared to the standard star method for the water lines in the J band with no loss of telescope time, but the oxygen lines were better corrected by the standard star method.