The electric solar wind sail (E-sail) is a way to propel a spacecraft by using the natural solar wind as a thrust source. The problem of secular spinrate change was identified earlier which is due to the orbital Coriolis effect and tends to slowly increase or decrease the sail's spinrate, depending on which way the sail is inclined with respect to the solar wind. Here we present an E-sail design and its associated control algorithm which enable spinrate control during propulsive flight by the E-sail effect itself. In the design, every other maintether ("T-tether") is galvanically connected through the remote unit with the two adjacent auxtethers, while the other maintethers ("I-tethers") are insulated from the tethers. This enables one to effectively control the maintether and auxtether voltages separately, which in turn enables spinrate control. We use a detailed numerical simulation to show that the algorithm can fully control the E-sail's spin state in real solar wind. The simulation includes a simple and realistic set of controller sensors: an imager to detect remote unit angular positions and a vector accelerometer. The imager resolution requirement is modest and the accelerometer noise requirement is feasible to achieve. The TI tether rig enables building E-sails that are able to control their spin state fully and yet are actuated by pure tether voltage modulation from the main spacecraft and requiring no functionalities from the remote units during flight.

The shape of a rotating electric solar wind sail under the centrifugal force and solar wind dynamic pressure is modeled to address the sail attitude maintenance and thrust vectoring. The sail rig assumes centrifugally stretched main tethers that extend radially outward from the spacecraft in the sail spin plane. Furthermore, the tips of the main tethers host remote units that are connected by auxiliary tethers at the sail rim. Here, we derive the equation of main tether shape and present both a numerical solution and an analytical approximation for the shape as parametrized both by the ratio of the electric sail force to the centrifugal force and the sail orientation with respect to the solar wind direction. The resulting shape is such that near the spacecraft, the roots of the main tethers form a cone, whereas towards the rim, this coning is flattened by the centrifugal force, and the sail is coplanar with the sail spin plane. Our approximation for the sail shape is parametrized only by the tether root coning angle and the main tether length. Using the approximate shape, we obtain the torque and thrust of the electric sail force applied to the sail. As a result, the amplitude of the tether voltage modulation required for the maintenance of the sail attitude is given as a torque-free solution. The amplitude is smaller than that previously obtained for a rigid single tether resembling a spherical pendulum. This implies that less thrusting margin is required for the maintenance of the sail attitude. For a given voltage modulation, the thrust vectoring is then considered in terms of the radial and transverse thrust components.

In Coulomb drag propulsion, a long high voltage tether or system of tethers gathers momentum from a natural plasma stream such as solar wind or ionospheric plasma ram flow. A positively polarised tether in the solar wind can be used for efficient general-purpose interplanetary propellantless propulsion (the electric solar wind sail or E-sail), whereas a negatively polarised tether in LEO can be used for efficient deorbiting of satellites (the plasma brake). Aalto-1 is a 3-U cubesat to be launched in May 2016. The satellite carries three scientific experiments including 100 m long Coulomb drag tether experiment. The tether is made of four 25 and 50 micrometre diameter aluminium wires that are ultrasonically bonded together every few centimetre intervals. The tether can be charged by an onboard voltage source up to one kilovolt positive and negative. The Coulomb drag is measured by monitoring the spin rate.

The electric solar wind sail (E-sail) propellantless propulsion device uses long, charged metallic tethers to tap momentum from the solar wind to produce spacecraft propulsion. If flying through planetary or moon eclipse, the long E-sail tethers can undergo significant thermal contraction and expansion. Rapid shortening of the tether increases its tension due to inertia of the tether and a Remote Unit that is located on the tether tip (a Remote Unit is part of typical E-sail designs). We analyse by numerical simulation the conditions under which eclipse induced stresses are safe for E-sail tethers. We calculate the closest safe approach distances for Earth, Moon, Venus, Mars, Jupiter, Ceres and an exemplary 300 km main belt asteroid Interamnia for circular, parabolic and hyperbolic orbits. We find that any kind of eclipsing is safe beyond approximately 2.5 au distance, but for terrestrial planets safety depends on the parameters of the orbit. For example, for Mars the safe distance with 20 km E-sail tether lies between Phobos and Deimos orbits.

The electric solar wind sail produces thrust by centrifugally spanned high voltage tethers interacting with the solar wind protons. The sail attitude can be controlled and attitude maneuvers are possible by tether voltage modulation synchronous with the sail rotation. Especially, the sail can be inclined with respect to the solar wind direction to obtain transverse thrust to change the osculating orbit angular momentum. Such an inclination has to be maintained by a continual control voltage modulation. Consequently, the tether voltage available for the thrust is less than the maximum voltage provided by the power system. Using a spherical pendulum as a model for a single rotating tether, we derive analytical estimations for the control efficiency for two separate sail control modes. One is a continuous control modulation that corresponds to strictly planar tether tip motion. The other is an on-off modulation with the tether tip moving along a closed loop on a saddle surface. The novel on-off mode is introduced here to both amplify the transverse thrust and reduce the power consumption. During the rotation cycle, the maximum voltage is applied to the tether only over two thrusting arcs when most of the transverse thrust is produced. In addition to the transverse thrust, we obtain the thrusting angle and electric power consumption for the two control modes. It is concluded that while the thrusting angle is about half of the sail inclination for the continuous modulation it approximately equals to the inclination angle for the on-off modulation. The efficiency of the on-off mode is emphasized when power consumption is considered, and the on-off mode can be used to improve the propulsive acceleration through the reduced power system mass.

We show that by having the auxtethers made partly or completely of conducting material and by controlling their voltages, it is possible to control the spin rate of the electric solar wind sail by using the electric sail effect itself. The proposed intrinsic spin rate control scheme has enough control authority to overcome the secular change of the spin rate due to orbital Coriolis effect.

The scientific mission of ESTCube-1, launched in May 2013, is to measure the Electric solar wind sail (E-sail) force in orbit. The experiment is planned to push forward the development of E-sail, a propulsion method recently invented at the Finnish Meteorological Institute. E-sail is based on extracting momentum from the solar wind plasma flow by using long thin electrically charged tethers. ESTCube-1 is equipped with one such tether, together with hardware capable of deploying and charging it. At the orbital altitude of ESTCube-1 (660--680~km) there is no solar wind present. Instead, ESTCube-1 shall observe the interaction between the charged tether and the ionospheric plasma. The ESTCube-1 payload uses a 10-meter, partly two-filament E-sail tether and a motorized reel on which it is stored. The tether shall be deployed from a spinning satellite with the help of centrifugal force. An additional mass is added at the tip of the tether to assist with the deployment. During E-sail experiment the tether shall be charged to 500~V potential. Both positive and negative voltages shall be experimented with. The voltage is provided by a dedicated high voltage source and delivered to the tether through a slip ring contact. When the negative voltage is applied to the tether, the satellite body is expected to attract electron flow capable of compensating for the ion flow, which runs to the tether from the surrounding plasma. With the positive voltage applied, onboard cold cathode electron guns are used to remove excess electrons to maintain the positive voltage of the tether. In this paper we present the design and structure of the tether payload of ESTCube-1.

We analyse the potential of the electric solar wind sail for solar system space missions. Applications studied include fly-by missions to terrestrial planets (Venus, Mars and Phobos, Mercury) and asteroids, missions based on non-Keplerian orbits (orbits that can be maintained only by applying continuous propulsive force), one-way boosting to outer solar system, off-Lagrange point space weather forecasting and low-cost impactor probes for added science value to other missions. We also discuss the generic idea of data clippers (returning large volumes of high resolution scientific data from distant targets packed in memory chips) and possible exploitation of asteroid resources. Possible orbits were estimated by orbit calculations assuming circular and coplanar orbits for planets. Some particular challenge areas requiring further research work and related to some more ambitious mission scenarios are also identified and discussed.