We present a new way to mitigate focal-ratio degradation (FRD) when using optical fibers to transport multimode light. Our approach exploits a custom multicore fiber (MCF) with six dissimilar cores that are single mode at ~1550 nm wavelength and minimally coupled over 7 m. We fabricated adiabatic mode-selective photonic lanterns (PLs) at each end of the MCF to create a fiber link with multimode ports, the PLs coupling each spatial mode of the multimode ports to a specific core of the MCF and vice versa. The PL-MCF-PL link exhibits superior FRD behavior compared to a conventional multimode fiber that also supports 6 modes, because it inhibits the transfer of light from lower-order modes to higher-order modes. These results open up a potentially powerful new approach to mitigate FRD in multimode fiber links, with particular applications in astronomical instruments.

Recently, we demonstrated how an astrophotonic light reformatting device, based on a multicore fibre photonic lantern and a three-dimensional waveguide component, can be used to efficiently reformat the point spread function of a telescope to a diffraction-limited psuedo-slit [arXiv:1512.07309]. Here, we demonstrate how such a device can also efficiently mitigate modal noise -- a potential source of instability in high resolution multi-mode fibre-fed spectrographs). To investigate the modal noise performance of the photonic reformatter, we have used it to feed light into a bench-top near-infrared spectrograph (R {\approx} 9,500, {\lambda} {\approx} 1550 nm). One approach to quantifying the modal noise involved the use of broadband excitation light and a statistical analysis of how the overall measured spectrum was affected by variations in the input coupling conditions. This approach indicated that the photonic reformatter could reduce modal noise by a factor of six when compared to a multi-mode fibre with a similar number of guided modes. Another approach to quantifying the modal noise involved the use of multiple spectrally narrow lines, and an analysis of how the measured barycentres of these lines were affected by variations in the input coupling. Using this approach, the photonic reformatter was observed to suppress modal noise to the level necessary to obtain spectra with stability close to that observed when using a single mode fibre feed. These results demonstrate the potential of using photonic reformatters to enable efficient multi-mode spectrographs that operate at the diffraction limit and are free of modal noise, with potential applications including radial velocity measurements of M-dwarfs.

Commodity cloud computing, as provided by commercial vendors such as Amazon, Google, and Microsoft, has revolutionized computing in many sectors. With the advent of a new class of big data, public access astronomical facility such as LSST, DKIST, and WFIRST, there exists a real opportunity to combine these missions with cloud computing platforms and fundamentally change the way astronomical data is collected, processed, archived, and curated. Making these changes in a cross-mission, coordinated way can provide unprecedented economies of scale in personnel, data collection and management, archiving, algorithm and software development and, most importantly, science.

Pan-STARRS1 has carried out a set of distinct synoptic imaging sky surveys including the $3\pi$ Steradian Survey and the Medium Deep Survey in 5 bands ($grizy_{P1}$). The mean 5$\sigma$ point source limiting sensitivities in the stacked 3$\pi$ Steradian Survey in $grizy_{P1}$ are (23.3, 23.2, 23.1, 22.3, 21.4) respectively. The upper bound on the systematic uncertainty in the photometric calibration across the sky is 7-12 millimag depending on the bandpass. The systematic uncertainty of the astrometric calibration using the Gaia frame comes from a comparison of the results with Gaia: the standard deviation of the mean and median residuals ($ \Delta ra, \Delta dec $) are (2.3, 1.7) milliarcsec, and (3.1, 4.8) milliarcsec respectively. The Pan-STARRS system and the design of the PS1 surveys are described and an overview of the resulting image and catalog data products and their basic characteristics are described together with a summary of important results. The images, reduced data products, and derived data products from the Pan-STARRS1 surveys are available to the community from the Mikulski Archive for Space Telescopes (MAST) at STScI.

One of the most useful techniques in astronomical instrumentation is image slicing. It enables a spectrograph to have a more compact angular slit, whilst retaining throughput and increasing resolving power. Astrophotonic components like the photonic lanterns and photonic reformatters can be used to replace bulk optics used so far. This study investigates the performance of such devices using end-to-end simulations to approximate realistic on-sky conditions. It investigates existing components, tries to optimize their performance and aims to understand better how best to design instruments to maximize their performance. This work complements the recent work in the field and provides an estimation for the performance of the new components.

Image slicing is a powerful technique in astronomy. It allows the instrument designer to reduce the slit width of the spectrograph, increasing spectral resolving power whilst retaining throughput. Conventionally this is done using bulk optics, such as mirrors and prisms, however more recently astrophotonic components known as photonic lanterns (PLs) and photonic reformatters have also been used. These devices reformat the multi-mode (MM) input light from a telescope into single-mode (SM) outputs, which can then be re-arranged to suit the spectrograph. The photonic dicer (PD) is one such device, designed to reduce the dependence of spectrograph size on telescope aperture and eliminate modal noise. We simulate the PD, by optimising the throughput and geometrical design using Soapy and BeamProp. The simulated device shows a transmission between 8 and 20 %, depending upon the type of adaptive optics (AO) correction applied, matching the experimental results well. We also investigate our idealised model of the PD and show that the barycentre of the slit varies only slightly with time, meaning that the modal noise contribution is very low when compared to conventional fibre systems. We further optimise our model device for both higher throughput and reduced modal noise. This device improves throughput by 6.4 % and reduces the movement of the slit output by 50%, further improving stability. This shows the importance of properly simulating such devices, including atmospheric effects. Our work complements recent work in the field and is essential for optimising future photonic reformatters.

In the last few years, integrated optics (IO) beam combiners have facilitated the emergence of 4-telescope interferometers such as PIONIER or GRAVITY, boosting the imaging capabilities of the VLTI. However, the spectral range beyond 2.2microns is not ideally covered by the conventional silica based IO. Here, we propose to consider new laser-written IO prototypes made of GLS glasses, a material that permits access to the mid-infrared spectral regime. Our goal is to conduct a full characterization of our mid-IR IO 2-telescope coupler in order to measure the performance levels directly relevant for long-baseline interferometry. We focus in particular on the exploitation of the L and M astronomical bands. We use a dedicated Michelson-interferometer setup to perform Fourier Transform spectroscopy on the coupler and measure its broadband interferometric performance. We also analyze the polarization properties of the coupler, the differential dispersion and phase degradation as well as the modal behavior and the total throughput. We measure broadband interferometric contrasts of 94.9% and 92.1% for unpolarized light in the L and M bands. Spectrally integrated splitting ratios are close to 50% but show chromatic dependence over the considered bandwidths. Additionally, the phase variation due to the combiner is measured and does not exceed 0.04rad and 0.07rad across the band L and M band, respectively. The total throughput of the coupler including Fresnel and injection losses from free-space is 25.4%. The laser-written IO GLS prototype combiners prove to be a reliable technological solution with promising performance for mid-infrared long-baseline interferometry. In the next steps, we will consider more advanced optical functions as well as a fiber-fed input and revise the optical design parameters in order the further enhance the total throughput and achromatic behavior.

The Planet Formation Imager (PFI) initiative aims at developing the next generation large scale facility for imaging astronomical optical interferometry operating in the mid-infrared. Here we report on the progress of the Planet Formation Imager Technical Working Group on the beam-combination instruments. We will discuss various available options for the science and fringe-tracker beam combination instruments, ranging from direct imaging, to non-redundant fiber arrays, to integrated optics solutions. Besides considering basic characteristics of the schemes, we will investigate the maturity of the available technological platforms at near- and mid-infrared wavelengths.

We review the potential of Astrophotonics, a relatively young field at the interface between photonics and astronomical instrumentation, for spectro-interferometry. We review some fundamental aspects of photonic science that drove the emer- gence of astrophotonics, and highlight the achievements in observational astrophysics. We analyze the prospects for further technological development also considering the potential synergies with other fields of physics (e.g. non-linear optics in condensed matter physics). We also stress the central role of fiber optics in routing and transporting light, delivering complex filters, or interfacing instruments and telescopes, more specifically in the context of a growing usage of adaptive optics.

Using a photonic reformatter to eliminate the effects of conventional modal noise could greatly improve the stability of a high resolution spectrograph. However the regimes where this advantage becomes clear are not yet defined. Here we will look at where modal noise becomes a problem in conventional high resolution spectroscopy and what impact photonic spectrographs could have. We will theoretically derive achievable radial velocity measurements to compare photonic instruments and conventional ones. We will discuss the theoretical and experimental investigations that will need to be undertaken to optimize and prove the photonic reformatting concept.

This paper reports on the modal noise characterisation of a hybrid reformatter. The device consists of a multicore-fibre photonic lantern and an ultrafast laser-inscribed slit reformatter. It operates around 1550 nm and supports 92 modes. Photonic lanterns transform a multimode signal into an array of single-mode signals, and thus combine the high coupling efficiency of multimode fibres with the diffraction-limited performance of single-mode fibres. This paper presents experimental measurements of the device point spread function properties under different coupling conditions, and its throughput behaviour at high spectral resolution. The device demonstrates excellent scrambling but its point spread function is not completely stable. Mode field diameter and mode barycentre position at the device output vary as the multicore-fibre is agitated due to the fabrication imperfections.

The spectral resolution of a dispersive astronomical spectrograph is limited by the trade-off between throughput and the width of the entrance slit. Photonic guided-wave transitions have been proposed as a route to bypass this trade-off, by enabling the efficient reformatting of incoherent seeing-limited light collected by the telescope into a linear array of single modes: a pseudo-slit which is highly multimode in one axis but diffraction-limited in the dispersion axis of the spectrograph. It is anticipated that the size of a single-object spectrograph fed with light in this manner would be essentially independent of the telescope aperture size. A further anticipated benefit is that such spectrographs would be free of `modal noise', a phenomenon that occurs in high-resolution multimode fibre-fed spectrographs due to the coherent nature of the telescope point-spread-function (PSF). We address these aspects by integrating a multicore fibre photonic lantern with an ultrafast laser inscribed three-dimensional waveguide interconnect to spatially reformat the modes within the PSF into a diffraction-limited pseudo-slit. Using the CANARY adaptive optics (AO) demonstrator on the William Herschel Telescope, and 1530 $\pm$ 80 nm stellar light, the device is found to exhibit a transmission of 47-53 % depending upon the mode of AO correction applied. We also show the advantage of using AO to couple light into such a device by sampling only the core of the CANARY PSF. This result underscores the possibility that a fully-optimised guided-wave device can be used with AO to provide efficient spectroscopy at high spectral resolution.

The spectral resolution of a dispersive spectrograph is dependent on the width of the entrance slit. This means that astronomical spectrographs trade-off throughput with spectral resolving power. Recently, optical guided-wave transitions known as photonic lanterns have been proposed to circumvent this trade-off, by enabling the efficient reformatting of multimode light into a pseudo-slit which is highly multimode in one axis, but diffraction-limited in the other. Here, we demonstrate the successful reformatting of a telescope point spread function into such a slit using a three-dimensional integrated optical waveguide device, which we name the photonic dicer. Using the CANARY adaptive optics demonstrator on the William Herschel Telescope, and light centred at 1530 nm with a 160 nm FWHM, the device shows a transmission of between 10 and 20\% depending upon the type of AO correction applied. Most of the loss is due to the overfilling of the input aperture in poor and moderate seeing. Taking this into account, the photonic device itself has a transmission of 57 $\pm$ 4\%.We show how a fully-optimised device can be used with AO to provide efficient spectroscopy at high spectral resolution.

We report the ultrafast laser fabrication and mid-IR characterization (3.39 microns) of four-port evanescent field directional couplers. The couplers were fabricated in a commercial gallium lanthanum sulphide glass substrate using sub-picosecond laser pulses of 1030 nm light. Straight waveguides inscribed using optimal fabrication parameters were found to exhibit propagation losses of 0.8 dB/cm. A series of couplers were inscribed with different interaction lengths, and we demonstrate power splitting ratios of between 8% and 99% for mid-IR light with a wavelength of 3.39 microns. These results clearly demonstrate that ultrafast laser inscription can be used to fabricate high quality evanescent field couplers for future applications in astronomical interferometry.

This article reports the advances on the development of mid-infrared integrated optics for stellar interferometry. The devices are fabricated by laser writing techniques on chalcogenide glasses. Laboratory characterizaton is reported and analyzed.

Ultrafast laser inscription (ULI) is a rapidly maturing technique which uses focused ultrashort laser pulses to locally modify the refractive index of dielectric materials in three-dimensions (3D). Recently, ULI has been applied to the fabrication of astrophotonic devices such as integrated beam combiners, 3D integrated waveguide fan-outs and multimode-to-single mode convertors (photonic lanterns). Here, we outline our work on applying ULI to the fabrication of volume phase gratings (VPGs) in fused silica and gallium lanthanum sulphide (GLS) glasses. The VPGs we fabricated had a spatial frequency of 333 lines/mm. The optimum fused silica grating was found to exhibit a first order diffraction efficiency of 40 % at 633 nm, but exhibited approximately 40 % integrated scattered light. The optimum GLS grating was found to exhibit a first order diffraction efficiency of 71 % at 633 nm and less than 5 % integrated scattered light. Importantly for future astronomy applications, both gratings survived cooling to 20 K. This paper summarises the grating design and ULI manufacturing process, and provides details of the diffraction efficiency performance and blaze curves for the VPGs. In contrast to conventional fabrication technologies, ULI can be used to fabricate VPGs in almost any dielectric material, including mid-IR transmitting materials such as the GLS glass used here. Furthermore, ULI potentially provides the freedom to produce complex groove patterns or blazed gratings. For these reasons, we believe that ULI opens the way towards the development of novel VPGs for future astronomy related applications.

We present here our recent progress in the three-dimensional (3D) direct laser writing (DLW) of step-index core waveguides inside diverse technologically relevant dielectric substrates, with specific emphasis on the demonstration of DLW mid-infrared waveguiding in the whole transparency range of these materials.

Using ultrafast laser inscription, we report the fabrication of a prototype three-dimensional 121-waveguide fan-out device capable of reformatting the output of a 120 core multicore fiber (MCF) into a one-dimensional linear array. When used in conjunction with an actual MCF, we demonstrate that the reformatting function using this prototype would result in an overall throughput loss of approximately 7.0 dB. However, if perfect coupling from the MCF into the fan-out could be achieved, the reformatting function would result in an overall loss of only approximately 1.7 dB. With adequate development, similar devices could efficiently reformat the output of so-called "photonic lanterns" fabricated using highly multicore fibers.

The application of photonics to astronomy offers major advantages in the area of highly-multiplexed spectroscopy, especially when applied to extremely large telescopes. These include the suppression of the near-infrared night-sky spectrum [J. Bland-Hawthorn et al, Opt. Express 12, 5902 (2004), S. G. Leon-Saval et al, Opt. Lett. 30, 2545 (2005)] and the miniaturisation of spectrographs so that they may integrated into the light-path of individual spatial samples [J. Bland-Hawthorn et al, Proc SPIE 6269, 62690N (2006)]. Efficient collection of light from the telescope requires multimode optical fibres and three-dimensional photonic devices. We propose ultrafast laser inscription (ULI) [R. R. Thomson et al, Opt. Express 15, 11691 (2007)] as the best technology to fabricate 3D photonic devices for astrophotonic applications.

We present the first high resolution polarization map of the ultraviolet emission from the outer jet in M87. The data were obtained by the Faint Object Camera (FOC) on the Hubble Space Telescope. The polarization map has a resolution of 0.2 arcsec and was derived using data from three linearly polarized images combined with the best available calibration data. The ultraviolet emission is highly polarized (~40\%) with the magnetic vector aligned roughly with the jet axis, except in the region of the brightest knot (Knot A) where the position angle changes abruptly and the magnetic vector becomes perpendicular to the jet axis. A similar behaviour is seen in the 2cm VLA radio polarization map. By aligning the FOC and VLA data, we present ultraviolet--2cm spectral index, depolarization and rotation measure maps. We identify a region of high depolarization adjacent to Knot A. This is the first direct observational evidence that indicates the presence of a cloud or filament of dense thermal material which is mixed with the synchrotron emitting plasma of the jet. The interaction of the jet with this cloud is likely to be responsible for the sudden increase in the brightness of the jet at Knot A due to an induced shock. We suggest that the dark line seen in the 2cm radio data between Knot A and Knot C could be the shadow or magnetotail of the depolarizing cloud in the jet.

HST images of the western hot spot of the nearby FRII radio galaxy Pictor A resolve the hot spot into an amorphous region of highly polarized wisps. The high polarization (>~ 50%) indicates that the optical emission is synchrotron radiation and that the magnetic field structure has been well resolved. The magnetic field is oriented nearly perpendicular to the jet axis and apparently very uniform. We interpret these observations in terms of a compressed magnetic field at the working surface where the jet impinges on the intergalactic medium some 100 kpc from the nucleus of the host galaxy. Keywords: Polarization --- radiation mechanisms: nonthermal --- galaxies: active --- galaxies: individual: Pictor A --- galaxies: jets.