This paper examines the effectiveness of an asteroid exploration architecture comprised of multiple nanosatellite sized spacecraft deployed from a single mother ship into a heliocentric orbit in the main asteroid belt where the mothership is ideally located in region of high density. Basic mission requirements associated with a Mother-Daughter architecture are established utilizing a relatively large number (10-20) daughter spacecraft distributed from a mothership within the asteroid belt for the purpose of executing sample and return missions. A number of trade analyses are performed to establish system performance to changes in initial orbit, delta-V capability and maximum small spacecraft flight time. The balance between the initial delta-V burn and asteroid velocity matching are also examined, with a goal of minimizing the amount of fuel needed in the small spacecraft. Preliminary requirements for the system are established using these results, and a conceptual design is presented for comparison to other asteroid exploration techniques. Preliminary results indicate that the aforementioned concept of a mothership with small spacecraft is viable and should be considered as an alternative approach to first order surveying of the asteroid belt.

The recent observation of interstellar objects, 1I/Oumuamua and 2I/Borisov cross the solar system opened new opportunities for planetary science and planetary defense. As the first confirmed objects originating outside of the solar system, there are myriads of origin questions to explore and discuss, including where they came from, how did they get here and what are they composed of. Besides, there is a need to be cognizant especially if such interstellar objects pass by the Earth of potential dangers of impact. Specifically, in the case of Oumuamua, which was detected after its perihelion, passed by the Earth at around 0.2 AU, with an estimated excess speed of 60 km/s relative to the Earth. Without enough forewarning time, a collision with such high-speed objects can pose a catastrophic danger to all life Earth. Such challenges underscore the importance of detection and exploration systems to study these interstellar visitors. The detection system can include a spacecraft constellation with zenith-pointing telescope spacecraft. After an event is detected, a spacecraft swarm can be deployed from Earth to flyby past the visitor. The flyby can then be designed to perform a proximity operation of interest. This work aims to develop algorithms to design these swarm missions through the IDEAS (Integrated Design Engineering & Automation of Swarms) architecture. Specifically, we develop automated algorithms to design an Earth-based detection constellation and a spacecraft swarm that generates detailed surface maps of the visitor during the rendezvous, along with their heliocentric cruise trajectories.

Near-Earth small-body mission targets 162173 Ryugu, 101955 Bennu, and 25143 Itokawa produce gravity fields around 4 orders of magnitude below that of Earth and their irregular shapes, combined with rotational effects produce varying surface potentials. Still, we observe familiar geologic textures and landforms that are the result of the granular physical processes that take place on their surfaces. The nature of these landforms, however, their origins, and how these surfaces react to interrogation by probes, landers, rovers, and penetrators, remain largely unknown, and therefore landing on an asteroid and manipulating its surface material remains a daunting challenge. The AOSAT+ design is a 12U CubeSat that will be in Low-Earth Orbit (LEO) and that will operate as a spinning on-orbit centrifuge. Part of this 12U CubeSat will contain a laboratory that will recreate asteroid surface conditions using crushed meteorite as a regolith proxy. The spinning of the laboratory will simulate the surface gravity of asteroids 2 km and smaller. The result is a bed of realistic regolith, the environment that landers and diggers and maybe astronauts will interact with. A crucial component of this mission involves the reproduction of the experimental results in numerical simulation in order to extract the material parameters of the regolith and its behavior in a sustained, very low but nonzero-gravity environment.

The next frontier in solar system exploration will be missions targeting extreme and rugged environments such as caves, canyons, cliffs and crater rims of the Moon, Mars and icy moons. These environments are time capsules into early formation of the solar system and will provide vital clues of how our early solar system gave way to the current planets and moons. These sites will also provide vital clues to the past and present habitability of these environments. Current landers and rovers are unable to access these areas of high interest due to limitations in precision landing techniques, need for large and sophisticated science instruments and a mission assurance and operations culture where risks are minimized at all costs. Our past work has shown the advantages of using multiple spherical hopping robots called SphereX for exploring these extreme environments. Our previous work was based on performing exploration with a human-designed baseline design of a SphereX robot. However, the design of SphereX is a complex task that involves a large number of design variables and multiple engineering disciplines. In this work we propose to use Automated Multidisciplinary Design and Control Optimization (AMDCO) techniques to find near optimal design solutions in terms of mass, volume, power, and control for SphereX for different mission scenarios.

Exploration of terrestrial planets such as Mars are conducted using orbiters, landers and rovers. Cameras and instruments onboard orbiters have enabled global mapping of Mars at low spatial resolution. Landers and rovers such as the Mars Science Laboratory (MSL) carry state-of-the-art instruments to characterize small localized areas. This leaves a critical gap in exploration capabilities: mapping regions in the hundreds of kilometers range. In this paper, we extend our work on CubeSat-sized sailplanes with detailed design studies of different aircraft configurations and payloads, identifying generalized design principles for autonomous sailplane-based surface reconnaissance and science applications. We further analyze potential wing deployment technologies, including conventional inflatables with hardened membranes, use of composite inflatables, and quick-setting foam. We perform detailed modeling of the Martian atmosphere and possible flight patterns at Jerezo crater using the Mars Regional Atmospheric Modeling System (MRAMS) to provide realistic atmospheric conditions at the landing site for NASA's 2020 rover. We revisit the feasibility of the Mars Sailplane concept, comparing it to previously proposed solutions, and identifying pathways to build laboratory prototypes for high-altitude Earth based testing. Finally, our work will analyze the implications of this technology for exploring other planetary bodies with atmospheres, including Venus and Titan.

The science and origins of asteroids is deemed high priority in the Planetary Science Decadal Survey. Two of the main questions from the Decadal Survey pertain to what the "initial stages, conditions, and processes of solar system formation and the nature of the interstellar matter" that was present in the protoplanetary disk, as well as determining the "primordial sources for organic matter." Major scientific goals for the study of planetesimals are to decipher geological processes in SSSBs not determinable from investigation via in situ experimentation, and to understand how planetesimals contribute to the formation of planets. Ground based observations are not sufficient to examine SSSBs, as they are only able to measure what is on the surface of the body; however, in situ analysis allows for further, close up investigation as to the surface characteristics and the inner composure of the body. The Asteroid Mobile Imager and Geologic Observer (AMIGO) is a 1U stowed autonomous robot that can perform surface hopping on an asteroid with an inflatable structure. It contains science instruments to provide stereo context imaging, micro-imaging, seismic sensing, and electric field measurements. Multiple hopping robots are deployed as a team to eliminate single-point failure and add robustness to data collection. An on-board attitude control system consists of a thruster chip of discretized micro-nozzles that provides hopping thrust and a reaction wheel for controlling the third axis. For the continued development of the robot, an engineering model is developed to test various components and algorithms.

The exploration of small bodies in the Solar System is a high priority planetary science. Asteroids, comets, and planetary moons yield important information about the evolution of the Solar System. Additionally, they could provide resources for a future space economy. While much research has gone into exploring asteroids and comets, dedicated spacecraft missions to planetary moons are few and far between. There are three fundamental challenges of a spacecraft mission to the planetary moons: The first challenge is that the spheres of influence of most moons (except that of Earth) are small and, in many cases, virtually absent. The second is that many moons are tidally locked to their planets, which means that an observer on the planet will have an entire hemisphere, which is always inaccessible. The third challenge is that at a given time about half of the region will be in the Sun's shadow. Therefore, a single spacecraft mission to observe the planetary moon cannot provide complete coverage. Such a complex task can be solved using a swarm approach, where the mapping task is delegated to multiple low-cost spacecraft. Clearly, the design of a swarm mission for such a dynamic environment is challenging. For this reason, we have proposed the Integrated Design Engineering & Automation of Swarms (IDEAS) software to perform automated end-to-end design of swarm missions. Specifically, it will use a sub-module known as the Automated Swarm Designer module to find optimal swarm configurations suited for a given mission. In our previous work, we have developed the Automated Swarm Design module to find swarm configurations for asteroid mapping operations. In this work, we will evaluate the capability of the Automated Swarm module to design missions to planetary moons.

The rapid advancement and miniaturization of spacecraft electronics, sensors, actuators, and power systems have resulted in growing proliferation of small-spacecraft. Coupled with this is the growing number of rocket launches, with left-over debris marking their trail. The space debris problem has also been compounded by test of several satellite killer missiles that have left large remnant debris fields. In this paper, we assume a future in which the Kessler Effect has taken hold and analyze the implications on the design of small-satellites and CubeSats. We use a multiprong approach of surveying the latest technologies, including the ability to sense space debris in orbit, perform obstacle avoidance, have sufficient shielding to take on small impacts and other techniques to mitigate the problem. Detecting and tracking space debris threats on-orbit is expected to be an important approach and we will analyze the latest vision algorithms to perform the detection, followed by quick reaction control systems to perform the avoidance. Alternately there may be scenarios where the debris is too small to track and avoid. In this case, the spacecraft will need passive mitigation measures to survive the impact. Based on these conditions, we develop a strawman design of a small spacecraft to mitigate these challenges. Based upon this study, we identify if there is sufficient present-day COTS technology to mitigate or shield satellites from the problem. We conclude by outlining technology pathways that need to be advanced now to best prepare ourselves for the worst-case eventuality of Kessler Effect taking hold in the upper altitudes of Low Earth Orbit.

Earth is constantly being bombarded with material from space. Most of the natural material end up being dust grains that litter the surface of Earth, but larger bodies are known to impact every few decades. The most recent large impact was Chelyabinsk which set off a 500-kiloton explosion which was 40 times that of the Hiroshima nuclear explosion. Apart from meteors, there is a growing threat of space assets deorbiting. With these impending space threats, it is critical to have a constellation of satellites to autonomously lookout for meteors and reentering space debris. By using multiple spacecraft, it is possible to perform multipoint observation of the event. Through multipoint observation, it is possible to triangulate the location of the observed event. The detection, tracking, and analysis of these objects all need to be performed autonomously. Our previous work focused on developing several vision algorithms including blob-detection, feature detection, and neural network-based image segment classification. For this multipoint observation to occur, it requires multiple spacecraft to coordinate their actions particularly fixating on the space observation target. Furthermore, communication and coordination are needed for bringing new satellites into observation view and removing other satellites that have lost their view. In this paper, we analyze state-of-the-art observation technology for small satellites and perform detailed design of its implementation. Through this study, we estimate the error estimates on position, velocity, and acceleration. We presume use of low to mid-tier cameras for the spacecraft.

The Lunar Gateway is expected to be positioned on-orbit around the Moon or in a Halo orbit at the L2 Lagrange point. The proposed Lunar Gateway is a game-changer for enabling new, high-priority lunar science utilizing Cu-beSats and presents a refreshing new opportunity for utilization of these small spacecraft as explorers. In context, CubeSats are being stretched to their limits as interplanetary explorers. The main technological hurdles include high-bandwidth communications and reliable high delta-v propulsion. Advances in deep-space attitude determination and control has been made possible from the recent NASA JPL MarCO missions. Due to these limitations, CubeSats are primarily designed to be dropped-off from a larger mission. The limited mass and volume have required compromises of the onboard science instruments, longer wait times to send back science data to Earth, shorter mission durations or higher accepted risk. With the Lunar Gateway being planned to be closer to the Moon, it will provide significant savings for a propulsion system and provide a primary relay for communication apart from the DSN and enable tele-operated command/control. These three factors can simplify the mission enabling routine deployment of CubeSats into lunar orbit and enable surface missions. In this paper, we present preliminary designs of 2 CubeSat lunar landers that will explore the lunar pits, Mare Tranquilitatis and the remnant magnetic fields Reiner Gamma.

There is growing demand for satellite swarms and constellations for global positioning, remote sensing and relay communication in higher LEO orbits. This will result in many obsolete, damaged and abandoned satellites that will remain on-orbit beyond 25 years. These abandoned satellites and space debris maybe economically valuable orbital real-estate and resources that can be reused, repaired or upgraded for future use. Space traffic management is critical to repair damaged satellites, divert satellites into warehouse orbits and effectively de-orbit satellites and space debris that are beyond repair and salvage. Current methods for on-orbit capture, servicing and repair require a large service satellite. However, by accessing abandoned satellites and space debris, there is an inherent heightened risk of damage to a servicing spacecraft. Sending multiple small-robots with each robot specialized in a specific task is a credible alternative, as the system is simple and cost-effective and where loss of one or more robots does not end the mission. In this work, we outline an end to end multirobot system to capture damaged and abandoned spacecraft for salvaging, repair and for de-orbiting. We analyze the feasibility of sending multiple, decentralized robots that can work cooperatively to perform capture of the target satellite as a first step, followed by crawling onto damage satellites to perform detailed mapping. After obtaining a detailed map of the satellite, the robots will proceed to either repair and replace or dismantle components for salvage operations. Finally, the remaining components will be packaged with a de-orbit device for accelerated de-orbit.

Exploration of Mars has been made possible using a series of landers, rovers and orbiters. The HiRise camera on the Mars Reconnaissance Orbiter (MRO) has captured high-resolution images covering large tracts of the surface. However, orbital images lack the depth and rich detail obtained from in-situ exploration. Rovers such as Mars Science Laboratory and upcoming Mars 2020 carry state-of-the-art science laboratories to perform in-situ exploration and analysis. However, they can only cover a small area of Mars through the course of their mission. A critical capability gap exists in our ability to image, provide services and explore large tracts of the surface of Mars required for enabling a future human mission. A promising solution is to develop a reconnaissance sailplane that travels tens to hundreds of kilometers per sol. The aircraft would be equipped with imagers that provide that in-situ depth of field, with coverage comparable to orbital assets such as MRO. A major challenge is that the Martian carbon dioxide atmosphere is thin, with a pres-sure of 1% of Earth at sea level. To compensate, the aircraft needs to fly at high-velocities and have sufficiently large wing area to generate the required lift. Inflatable wings are an excellent choice as they have the lowest mass and can be used to change shape (morph) depending on aerodynamic or con-trol requirements. In this paper, we present our design of an inflatable sail-plane capable of deploying from a 12U CubeSat platform. A pneumatic de-ployment mechanism ensures highly compact stowage volumes and minimizes complexity.

Water has been identified as a critical resource both to sustain human-life but also for use in propulsion, attitude-control, power, thermal and radiation pro-tection systems. Water may be obtained off-world through In-Situ Resource Utilization (ISRU) in the course of human or robotic space exploration that replace materials that would otherwise be shipped from Earth. Water has been highlighted by many in the space community as a credible solution for affordable/sustainable exploration. Water can be extracted from the Moon, C-class Near Earth Objects (NEOs), surface of Mars and Martian Moons Pho-bos and Deimos and from the surface of icy, rugged terrains of Ocean Worlds. However, use of water for propulsion faces some important techno-logical barriers. A technique to use water as a propellant is to electrolyze it into hydrogen and oxygen that is then pulse-detonated. High-efficiency elec-trolysis requires use of platinum-catalyst based fuel cells. Even trace ele-ments of sulfur and carbon monoxide found on planetary bodies can poison these cells making them unusable. In this work, we develop steam-based propulsion that avoids the technological barriers of electrolyzing impure water as propellant. Using a solar concentrator, heat is used to extract the water which is then condensed as a liquid and stored. Steam is then formed using the solar thermal reflectors to concentrate the light into a nanoparticle-water mix. This solar thermal heating (STH) process converts 80 to 99% of the in-coming light into heat.

There are more than 750,000 asteroids identified in the main belt. These asteroids are diverse in composition and size. Some of these asteroids can be traced back to the early solar system and can provide insight into the origins of the so-lar system, origins of Earth and origins of life. Apart from being important tar-gets for science exploration, asteroids are strategically placed due to their low-gravity well, making it low-cost to transport material onto and way from them. They hold valuable resources such as water, carbon, metals including iron, nickel and platinum to name a few. These resources maybe used in refueling depots for interplanetary spacecraft and construction material for future space colonies, communication relays and space telescopes. The costs of getting to the main asteroid belt, combined with large numbers of objects to be explored encourage the application of small spacecraft swarms. The size and capability of the result-ing nano-spacecraft can make detection from Earth difficult. This paper dis-cusses a method by which a spacecraft can establish ephemeris autonomously using line of sight measurements to nearby asteroids with Extended Kalman Filtering techniques, without knowing accurate ephemeris of either the asteroids or the spacecraft initially. A description of the filter implementation is followed by examples of resultant performance.

The science and origins of asteroids is deemed high priority in the Planetary Science Decadal Survey. Major scientific goals for the study of planetesimals are to decipher geological processes in SSSBs not determinable from investigation via in-situ experimentation, and to understand how planetesimals contribute to the formation of planets. Ground based observations are not sufficient to examine SSSBs, as they are only able to measure what is on the surface of the body; however, in-situ analysis allows for further, close up investigation as to the surface characteristics and the inner composure of the body. To this end, the Asteroid Mobile Imager and Geologic Observer (AMIGO) an autonomous semi-inflatable robot will operate in a swarm to efficiently characterize the surface of an asteroid. The stowed package is 10x10x10 cm (equivalent to a 1U CubeSat) that deploys an inflatable sphere of ~1m in diameter. Three mobility modes are identified and designed: ballistic hopping, rotation during hops, and up-righting maneuvers. Ballistic hops provide the AMIGO robot the ability to explore a larger portion of the asteroid's surface to sample a larger area than a stationary lander. Rotation during the hop entails attitude control of the robot, utilizing propulsion and reaction wheel actuation. In the event of the robot tipping or not landing up-right, a combination of thrusters and reaction wheels will correct the robot's attitude. The AMIGO propulsion system utilizes sublimate-based micro-electromechanical systems (MEMS) technology as a means of lightweight, low-thrust ballistic hopping and coarse attitude control. Each deployed AMIGO will hop across the surface of the asteroid multiple times.

There are thousands of asteroids in near-Earth space and millions in the Main Belt. They are diverse in physical properties and composition and are time capsules of the early solar system. This makes them strategic locations for planetary science, resource mining, planetary defense/security and as inter-planetary depots and communication relays. However, asteroids are a chal-lenging target for surface exploration due it its low but highly nonlinear gravity field. In such conditions, mobility through ballistic hopping possess multiple advantages over conventional mobility solutions and as such hop-ping robots have emerged as a promising platform for future exploration of asteroids and comets. They can traverse large distances over rough terrain with the expenditure of minimum energy. In this paper we present ballistic hopping dynamics and its motion planning on an asteroid surface with highly nonlinear gravity fields. We do it by solving Lambert's orbital boundary val-ue problem in irregular gravity fields by a shooting method to find the initial velocity required to intercept a target. We then present methods to localize the hopping robot using pose estimation by successive scan matching with a 3D laser scanner. Using the above results, we provide methods for motion planning on the asteroid surface over long distances. The robot will require to perform multiple hops to reach a desired goal from its initial position while avoiding obstacles. The study is then be extended to find optimal tra-jectories to reach a desired goal by visiting multiple waypoints.

Understanding the physics of small bodies such as asteroids, comets, and planetary moons will help us understand the formation of the solar system, and also provide us with resources for a future space economy. Due to these reasons, missions to small bodies are actively being pursued. However, the surfaces of small bodies contain unpredictable and interesting features such as craters, dust, and granular matter, which need to be observed carefully before a lander mission is even considered. This presents the need for a surveillance spacecraft to observe the surface of small bodies where these features exist. While traditionally, the small body exploration has been performed by a large monolithic spacecraft, a group of small, low-cost spacecraft can enhance the observational value of the mission. Such a spacecraft swarm has the advantage of providing longer observation time and is also tolerant to single point failures. In order to optimize a space-craft swarm mission design, we proposed the Integrated Design Engineering & Automation of Swarms (IDEAS) software which will serve as an end-to-end tool for theoretical swarm mission design. The current work will focus on developing the Automated Swarm Designer module of the IDEAS software by extending its capabilities for exploring surface features on small bodies while focusing on the attitude behaviors of the spacecraft in the swarm. We begin by classifying space-craft swarms into 5 classes based on the level of coordination. In the current work, we design Class 2 swarms, whose spacecraft operate in a decentralized fashion but coordinate for communication. We demonstrate the Class 2 swarm in 2 different configurations, based on the roles of the participating spacecraft.

Swarms of small spacecraft offer whole new capabilities in Earth observation, global positioning and communications compared to a large monolithic spacecraft. These small spacecrafts can provide bigger apertures that increase gain in communication antennas, increase area coverage or effective resolution of distributed cameras and enable persistent observation of ground or space targets. However, there remain important challenges in operating large number of spacecrafts at once. Current methods would require a large number of ground operators monitor and actively control these spacecrafts which poses challenges in terms of coordination and control which prevents the technology from scaled up in cost-effective manner. Technologies are required to enable one ground operator to manage tens if not hundreds of spacecrafts. We propose to utilize laser beams directed from the ground or from a command and control spacecraft to organize and manage a large swarm. Each satellite in the swarm will have a customized "smart skin" con-taining solar panels, power and control circuitry and an embedded secondary propulsion unit. A secondary propulsion unit may include electrospray pro-pulsion, solar radiation pressure-based system, photonic laser thrusters and Lorentz force thrusters. Solar panels typically occupy the largest surface area on an earth orbiting satellite. A laser beam from another spacecraft or from the ground would interact with solar panels of the spacecraft swarm. The laser beam would be used to select a 'leader' amongst a group of spacecrafts, set parameters for formation-flight, including separation distance, local if-then rules and coordinated changes in attitude and position.

The exponential rise in small-satellites and CubeSats in Low Earth Orbit (LEO) poses important challenges for future space traffic management. At altitudes of 600 km and lower, aerodynamic drag accelerates de-orbiting of satellites. However, placement of satellites at higher altitudes required for constellations pose important challenges. The satellites will require on-board propulsion to lower their orbits to 600 km and let aerodynamic drag take-over. In this work we analyze solutions for de-orbiting satellites at altitudes of up to 3000 km. We consider a modular robotic de-orbit device that has stowed volume of a regular CubeSat. The de-orbit device would be externally directed towards a dead satellite or placed on one by an external satellite servicing system. Our solutions are intended to be simple, high-reliability devices that operate in a passive manner, requiring no active electronics or utilize external beamed power in the form of radio frequency, microwave or laser to operate. Utilizing this approach, it is possible for an external, even ground based system to direct the de-orbit of a spacecraft. The role of an external system to direct the de-orbit is important to avoid accidental collisions. Some form of propulsion is needed to lower the orbit of the dead satellite or orbital debris. We considered green (non-toxic) propulsion methods including solar radiation pressure, solar-thermal propulsion using water steam, solar-electrolysis propulsion using water and use of electrodynamic tethers. Based on this trade-study we identify multiple solutions that can be used to de-orbit a spacecraft or orbital debris.

Planetary bodies such as asteroids, comets, and planetary moons are high-value science targets as they hold important information about the formation and evolution of our solar system. However, due to their low-gravity, variable sizes and shapes, dedicated orbiting spacecraft missions around these target bodies is difficult. Therefore, many planetary bodies are observed during flyby encounters, and consequently, the mapping coverage of the target body is limited. In this work, we propose the use of a spacecraft swarm to provide complete surface maps of a planetary body during a close encounter flyby. With the advancement of low-cost spacecraft technology, such a swarm can be realized by using multiple miniature spacecraft. The design of a swarm mission is a complex multi-disciplinary problem. To get started, we propose the Integrated Design Engineering & Automation of Swarms (IDEAS) software. In this work, we will introduce the development of the Automated Swarm Designer module of the software and apply it to total surface mapping of asteroid 433 Eros through flybys.

Exploration of small bodies, namely comets and asteroids remain a challenging endeavor due to their low gravity. The risk is so high that missions such as Hayabusa II and OSIRIS-REx will be performing touch and go missions to obtain samples. The next logical step is to perform longer-term mobility on the surface of these asteroid. This can be accomplished by sending small landers of a 1 kg or less with miniature propulsion systems that can just offset the force of asteroid gravity. Such a propulsion system would ideally be used to hop on the surface of the asteroid. Hopping has been found to be most efficient form of mobility on low-gravity. Use of wheels for rolling presents substantial challenges as the wheel can't gain traction to roll. The Asteroid Mobile Imager and Geologic Observer (AMIGO) utilizes 1 kg landers that are stowed in a 1U CubeSat configuration and deployed, releasing an inflatable that is 1 m in diameter. The inflatable is attached to the top of the 1U lander, enabling high speed communications and a means of easily tracking lander from an overhead mothership. Milligravity propulsion is required for the AMIGO landers to perform ballistic hops on the asteroid surface. The propulsion system is used to navigate the lander across the surface of the asteroid under the extremely low gravity while taking care to not exceed escape velocity.Although the concept for AMIGO missions is to use multiple landers, the more surface area evaluated by each lander the better. Without a propulsion system, each AMIGO will have a limited range of observable area. The propulsion system also serves as a rough attitude control system (ACS), as it enables pointing and regulation over where the lander is positioned via an array of MEMS thrusters.

There is an every-growing need to construct large space telescopes and structures for observation of exo-planets, main-belt asteroids and NEOs. Space observation capabilities can significant enhanced by large-aperture structures. Structures extending to several meters in size could potentially revolutionize observation enabling technologies. These include star-shades for imaging distant objects such as exo-planets and high-resolution large aperture telescopes. In addition to size, such structures require controllable precision surfaces and high packing efficiencies. A promising approach to achieving high compaction for large surface areas is by incorporating compliant materials or gossamers. Gossamer structures on their own do not meet stiffness requirements for controlled deployment. Supporting stiffening mechanisms are required to fully realize their structural potential. The accuracy of the 'active' surface constructed out of a gossamer additionally also depends on the load bearing structure that supports it. This paper investigates structural assemblies constructed from modular inflatable membranes stiffened pneumatically using inflation gas. These units assembled into composites can yield desirable characteristics. We present the design of large assemblies of these modular elements.

There are thousands of asteroids in near-Earth space and millions expected in the Main Belt. They are diverse in their physical properties and compositions. They are also time capsules of the early Solar System making them valuable for planetary science, and are strategic for resource mining, planetary defense/security and as interplanetary depots. But we lack direct knowledge of the geophysical behavior of an asteroid surface under milligravity conditions, and therefore landing on an asteroid and manipulating its surface material remains a daunting challenge. Towards this goal we are putting forth plans for a 12U CubeSat that will be in Low Earth Orbit and that will operate as a spinning centrifuge on-orbit. In this paper, we will present an overview of the systems engineering and instrumentation design on the spacecraft. Parts of this 12U CubeSat will contain a laboratory that will recreate asteroid surface conditions by containing crushed meteorite. The laboratory will spin at 1 to 2 RPM during the primary mission to simulate surface conditions of asteroids 2 km and smaller, followed by an extended mission where the spacecraft will spin at even higher RPM. The result is a bed of realistic regolith, the environment that landers and diggers and maybe astronauts will interact with. The CubeSat is configured with cameras, lasers, actuators and small mechanical instruments to both observe and manipulate the regolith at low simulated gravity conditions. A series of experiments will measure the general behavior, internal friction, adhesion, dilatancy, coefficients of restitution and other parameters that can feed into asteroid surface dynamics simulations. Effective gravity can be varied, and external mechanical forces can be applied.

Small-satellites and CubeSats offer a low-cost pathway to access Low Earth Orbit at altitudes of 450 km and lower thanks to miniaturization and advancement in reliability of commercial electronics. However, at these low altitudes, atmospheric drag has a critical effect on the satellite resulting in natural deorbits within months. As these small systems further increase in reliability and radiation tolerance they will be able readily access higher orbits at altitudes of 700 km and higher, where atmospheric drag has little to no effect. This requires alternative technologies to either de-orbit these small spacecrafts at the end of life or move them to a safe parking orbit. Use of propulsion and de-orbit mechanisms have been proposed, however they require active control systems to be trigged. Other typical de-orbit mechanism relies on complex mechanisms with many moving parts. In this work, we analyze the feasibility of using inflatable de-orbit devices that are triggered passively when a spacecraft is tumbling. Inflatables have already been proposed as hypersonic deccelerators that would carry large payload to the Martian surface. However, these systems are quite complex and need to withstand high-forces, temperature and enable survival of a critical payload. Furthermore, inflatables have been proposed as communication antennas and as structures using a class of sublimates that turn into gas under the vacuum of space. These inflatables system are relatively simple and does not require a specialized inflation system.

The wide availability of Commercial Off-The-Shelf (COTS) electronics that can withstand Low Earth Orbit conditions has opened avenue for wide deployment of CubeSats and small-satellites. CubeSats thanks to their low developmental and launch costs offer new opportunities for rapidly demonstrating on-orbit surveillance capabilities. In our earlier work, we proposed development of SWIMSat (Space based Wide-angle Imaging of Meteors) a 3U CubeSat demonstrator that is designed to observe illuminated objects entering the Earth's atmosphere. The spacecraft would operate autonomously using a smart camera with vision algorithms to detect, track and report of objects. Several CubeSats can track an object in a coordinated fashion to pinpoint an object's trajectory. An extension of this smart camera capability is to track unilluminated objects utilizing capabilities we have been developing to track and navigate to Near Earth Objects (NEOs). This extension enables detecting and tracking objects that can't readily be detected by humans. The system maintains a dense star map of the night sky and performs round the clock observations. Standard optical flow algorithms are used to obtain trajectories of all moving objects in the camera field of view. Through a process of elimination, certain stars maybe occluded by a transiting unilluminated object which is then used to first detect and obtain a trajectory of the object. Using multiple cameras observing the event from different points of view, it may be possible then to triangulate the position of the object in space and obtain its orbital trajectory. In this work, the performance of our space object detection algorithm coupled with a spacecraft guidance, navigation, and control system is demonstrated.

There are thousands of asteroids in near-Earth space and millions in the Main Belt. They are diverse in physical properties and composition and are time capsules of the early solar system. This makes them strategic locations for planetary science, resource mining, planetary defense/security and as interplanetary depots and communication relays. Landing on a small asteroid and manipulating its surface materials remains a major unsolved challenge fraught with high risk. The asteroid surface may contain everything from hard boulders to soft regolith loosely held by cohesion and very low-gravity. Upcoming missions Hayabusa II and OSIRIS-REx will perform touch and go operations to mitigate the risks of landing on an asteroid. This limits the contact time and requires fuel expenditure for hovering. An important unknown is the problem of getting stuck or making a hard impact with the surface. The Spacecraft Penetrator for Increasing Knowledge of NEOs (SPIKE) mission concept will utilize a small-satellite bus that is propelled using a xenon-fueled ion engine and will contain an extendable, low-mass, high-strength boom with a tip containing force-moment sensors. SPIKE will enable contact with the asteroid surface, where it will perform detailed regolith analysis and seismology as well as penetrometry, while keeping the main spacecraft bus at a safe distance. Using one or more long stilts frees the spacecraft from having to hover above the asteroid and thus substantially reduces or eliminates fuel use when doing science operations. This enables much longer missions that include a series of hops to multiple locations on the small-body surface.

An important and emerging component of planetary exploration is sample retrieval and return to Earth. Obtaining and analyzing rock samples can provide unprecedented insight into the geology, geo-history and prospects for finding past life and water. Current methods of exploration rely on mission scientists to identify objects of interests and this presents major operational challenges. Finding objects of interests will require systematic and efficient methods to quickly and correctly evaluate the importance of hundreds if not thousands of samples so that the most interesting are saved for further analysis by the mission scientists. In this paper, we propose an automated information theoretic approach to identify shapes of interests using a library of predefined interesting shapes. These predefined shapes maybe human input or samples that are then extrapolated by the shape matching system using the Superformula to judge the importance of newly obtained objects. Shape samples are matched to a library of shapes using the eigenfaces approach enabling categorization and prioritization of the sample. The approach shows robustness to simulated sensor noise of up to 20%. The effect of shape parameters and rotational angle on shape matching accuracy has been analyzed. The approach shows significant promise and efforts are underway in testing the algorithm with real rock samples.

We advocate a low-cost strategy for long-duration research into the 'milligravity' environment of asteroids, comets and small moons, where surface gravity is a vector field typically less than 1/1000 the gravity of Earth. Unlike the microgravity environment of space, there is a directionality that gives rise, over time, to strangely familiar geologic textures and landforms. In addition to advancing planetary science, and furthering technologies for hazardous asteroid mitigation and in-situ resource utilization, simplified access to long-duration milligravity offers significant potential for advancing human spaceflight, biomedicine and manufacturing. We show that a commodity 3U ($10\times10\times34$ cm$^3$) cubesat containing a laboratory of loose materials can be spun to 1 rpm = $2\pi/60$ s$^{-1}$ on its long axis, creating a centrifugal force equivalent to the surface gravity of a kilometer-sized asteroid. We describe the first flight demonstration, where small meteorite fragments will pile up to create a patch of real regolith under realistic asteroid conditions, paving the way for subsequent missions where landing and mobility technology can be flight-proven in the operational environment, in Low-Earth Orbit (LEO). The 3U design can be adapted for use onboard the International Space Station (ISS) to allow for variable gravity experiments under ambient temperature and pressure for a broader range of experiments.

The application of GNC devices on small robots is a game-changer that enables these robots to be mobile on low-gravity planetary surfaces and small bodies. Use of reaction wheels enables these robots to roll, hop, summersault and rest on precarious/sloped surfaces that would otherwise not be possible with conven-tional wheeled robots. We are extending this technology to enable robots to climb off-world canyons, cliffs and caves. A single robot may slip and fall, however, a multirobot system can work cooperatively by being interlinked using spring-tethers and work much like a team of mountaineers to systematically climb a slope. A multirobot system as we will show in this paper can climb sur-faces not possible with a single robot alone. We consider a team of four robots that are interlinked with tethers in an 'x' configuration. Each robot secures itself to a slope using spiny gripping actuators, and one by one each robot moves up-wards by crawling, rolling or hopping up the slope. If any one of the robots loses grip, slips or falls, the remaining robots will be holding it up as they are anchored. This distributed controls approach to cliff climbing enables the system to reconfigure itself where possible and avoid getting stuck at one hard to reach location. Instead, the risk is distributed and through close cooperation, the robots can identify multiple trajectories to climb a cliff or rugged surface. The benefits can also be realized on milligravity surfaces such as asteroids. Too fast a jump can result in the robot flying off the surface into space. Having multiple robots anchored to the surface keeps the entire system secure. Our work combines dynamics and control simulation to evaluate the feasibility of our approach. The simulation results show a promising pathway towards advanced development of this technology on a team of real robots.

Near Earth Asteroids (NEAs) are thought to contain a wealth of resources, including water, iron, titanium, nickel, platinum and silicates. Future space missions that can exploit these resources by performing In-Situ Resource Utilization (ISRU) gain substantial benefit in terms of range, payload capacity and mission flexibility. Compared to the Moon or Mars, the milligravity on some asteroids demands a fraction of the energy for digging and accessing hydrated regolith just below the surface. However, asteroids and small-bodies, because of their low gravity present a major challenge in landing, surface excavation and resource capture. These challenges have resulted in adoption of a "touch and go techniques", like the upcoming Osiris-rex sample-return mission. Previous asteroid excavation efforts have focused on discrete capture events (an extension of sampling technology) or whole-asteroid capture and processing. This paper analyzes the control of a bucket-wheel design for asteroid or small-body excavation. Our study focuses on system design of two counter rotating bucket-wheels that are attached to a hovering spacecraft. Regolith is excavated and heated to 1000 C to extract water. The water in turn is electrolyzed to produce hydrogen and oxygen for rocket fuel. We analyze control techniques to maximize traction of the bucket-wheels on the asteroid surface and minimize lift-off the surface, together with methods to dig deeper into the asteroid surface. Our studies combine analytical models, with simulation and hardware testing. For initial evaluation of material-spacecraft dynamics and mechanics, we assume lunar-like regolith for bulk density, particle size and cohesion. Our early studies point towards a promising pathway towards refinement of this technology for demonstration aboard a future space mission.

Wheeled planetary rovers such as the Mars Exploration Rovers (MERs) and Mars Science Laboratory (MSL) have provided unprecedented, detailed images of the Mars surface. However, these rovers are large and are of high-cost as they need to carry sophisticated instruments and science laboratories. We propose the development of low-cost planetary rovers that are the size and shape of cantaloupes and that can be deployed from a larger rover. The rover named SphereX is 2 kg in mass, is spherical, holonomic and contains a hopping mechanism to jump over rugged terrain. A small low-cost rover complements a larger rover, particularly to traverse rugged terrain or roll down a canyon, cliff or crater to obtain images and science data. While it may be a one-way journey for these small robots, they could be used tactically to obtain high-reward science data. The robot is equipped with a pair of stereo cameras to perform visual navigation and has room for a science payload. In this paper, we analyze the design and development of a laboratory prototype. The results show a promising pathway towards development of a field system.

Communication with a spacecraft is typically performed using Radio Frequency (RF). RF is a well-established and well-regulated technology that enables communication over long distances as proven by the Voyager 1 & II missions. However, RF requires licensing of very limited radio spectrum and this poses a challenge in the future, particularly with spectrum time-sharing. This is of a concern for emergency communication when it is of utmost urgency to contact the spacecraft and maintain contact, particularly when there is a major mission anomaly or loss of contact. For these applications, we propose a backup laser communication system where a laser is beamed towards a satellite and the onboard photovoltaics acts as a laser receiver. This approach enables a laser ground station to broadcast commands to the spacecraft in times of emergency. Adding an actuated reflector to the laser receiver on the spacecraft enables two-way communication between ground and the spacecraft, but without the laser being located on the spacecraft. In this paper, we analyze the feasibility of the concept in the laboratory and develop a benchtop experiment to verify the concept. We have also developed a preliminary design for a 6U CubeSat-based demonstrator to evaluate technology merits

Wheeled ground robots are limited from exploring extreme environments such as caves, lava tubes and skylights. Small robots that can utilize unconventional mobility through hopping, flying or rolling can overcome these limitations. Mul-tiple robots operating as a team offer significant benefits over a single large ro-bot, as they are not prone to single-point failure, enable distributed command and control and enable execution of tasks in parallel. These robots can complement large rovers and landers, helping to explore inaccessible sites, obtaining samples and for planning future exploration missions. Our robots, the SphereX, are 3-kg in mass, spherical and contain computers equivalent to current smartphones. They contain an array of guidance, navigation and control sensors and electronics. SphereX contains room for a 1-kg science payload, including for sample return. Our work in this field has recognized the need for miniaturized chemical mobility systems that provide power and propulsion. Our research explored the use of miniature rockets, including solid rockets, bi-propellants including RP1/hydrogen-peroxide and polyurethane/ammonium-perchlorate. These propulsion options provide maximum flight times of 10 minutes on Mars. Flying, especially hovering consumes significant fuel; hence, we have been developing our robots to perform ballistic hops that enable the robots to travel efficiently over long distances. Techniques are being developed to enable mid-course correction during a ballistic hop. Using multiple cameras, it is possible to reconstitute an image scene from motion blur. Hence our approach is to enable photo mapping as the robots travel on a ballistic hop. The same images would also be used for navigation and path planning. Using our proposed design approach, we are developing low-cost methods for surface exploration of planetary bodies using a network of small robots.

Wheeled ground robots are limited from exploring extreme environments such as caves, lava tubes and skylights. Small robots that utilize unconventional mobility through hopping, flying and rolling can overcome many roughness limitations and thus extend exploration sites of interest on Moon and Mars. In this paper we introduce a network of 3 kg, 0.30 m diameter ball robots (pit-bots) that can fly, hop and roll using an onboard miniature propulsion system. These pit-bots can be deployed from a lander or large rover. Each robot is equipped with a smartphone sized computer, stereo camera and laser rangefinder to per-form navigation and mapping. The ball robot can carry a payload of 1 kg or perform sample return. Our studies show a range of 5 km and 0.7 hours flight time on the Moon.

Space systems such as communication satellites, earth observation satellites and space telescopes require precise pointing to observe fixed targets over prolonged time. These systems typically use reaction-wheels to slew the spacecraft and gimballing systems containing motors to achieve precise pointing. Motor based actuators have limited life as they contain moving parts that require lubrication in space. Alternate methods have utilized piezoelectric actuators. This paper presents Shape memory alloys (SMA) actuators for control of a deployable antenna placed on a satellite. The SMAs are operated as a series of distributed linear actuators. These distributed linear actuators are not prone to single point failures and although each individual actuator is imprecise due to hysteresis and temperature variation. The system as a whole achieves reliable results. The SMAs can be programmed to perform a series of periodic motion and operate as a mechanical guidance system that is not prone to damage from radiation or space weather. Efforts are focused on developing a system that can achieve one degree pointing accuracy at first, with an ultimate goal of achieving a few arc seconds accuracy. Bench top models of the actuator system has been developed and working towards testing the system under vacuum. A demonstration flight of the technology is planned aboard a CubeSat.

Advances in GNC, particularly from miniaturized control electronics, reaction-wheels and attitude determination sensors make it possible to design surface probes and small robots to perform surface exploration and science on low-gravity environments. These robots would use their reaction wheels to roll, hop and tumble over rugged surfaces. These robots could provide 'Google Streetview' quality images of off-world surfaces and perform some unique science using penetrometers. These systems can be powered by high-efficiency fuel cells that operate at 60-65 % and utilize hydrogen and oxygen electrolyzed from water. However, one of the major challenges that prevent these probes and robots from performing long duration surface exploration and science is thermal design and control. In the inner solar system, during the day time, there is often enough solar-insolation to keep these robots warm and power these devices, but during eclipse the temperatures falls well below storage temperature. We have developed a thermal control system that utilizes chemicals to store and dispense heat when needed. The system takes waste products, such as water from these robots and transfers them to a thermochemical storage system. These thermochemical storage systems when mixed with water (a waste product from a PEM fuel cell) releases heat. Under eclipse, the heat from the thermochemical storage system is released to keep the probe warm enough to survive. In sunlight, solar photovoltaics are used to electrolyze the water and reheat the thermochemical storage system to release the water. Our research has showed thermochemical storage systems are a feasible solution for use on surface probes and robots for applications on the Moon, Mars and asteroids.

CubeSats and small satellites are emerging as low-cost tools to perform astronomy, exoplanet searches and earth observation. These satellites can be dedicated to pointing at targets for weeks or months at a time. This is typically not possible on larger missions where usage is shared. Current satellites use reaction wheels and where possible magneto-torquers to control attitude. However, these actuators can induce jitter due to various sources. In this work, we introduce a new class of actuators that exploit radiometric forces induced by gasses on surface with a thermal gradient. Our work shows that a CubeSat or small spacecraft mounted with radiometric actuators can achieve precise pointing of few arc-seconds or less and avoid the jitter problem. The actuator is entirely solid-state, containing no moving mechanical components. This ensures high-reliability and long-life in space. A preliminary design for these actuators is proposed, followed by feasibility analysis of the actuator performance.

Exploration of asteroids and small-bodies can provide valuable insight into the origins of the solar system, into the origins of Earth and the origins of the building blocks of life. However, the low-gravity and unknown surface conditions of asteroids presents a daunting challenge for surface exploration, manipulation and for resource processing. This has resulted in the loss of several landers or shortened missions. Fundamental studies are required to obtain better readings of the material surface properties and physical models of these small bodies. The Asteroid Origins Satellite 1 (AOSAT 1) is a CubeSat centrifuge laboratory that spins at up to 4 rpm to simulate the milligravity conditions of sub 1 km asteroids. Such a laboratory will help to de-risk development and testing of landing and resource processing technology for asteroids. Inside the laboratory are crushed meteorites, the remains of asteroids. The laboratory is equipped with cameras and actuators to perform a series of science experiments to better understand material properties and asteroid surface physics. These results will help to improve our physics models of asteroids. The CubeSat has been designed to be low-cost and contains 3-axis magnetorquers and a single reaction-wheel to induce spin. In our work, we first analyze how the attitude control system will de-tumble the spacecraft after deployment. Further analysis has been conducted to analyze the impact and stability of the attitude control system to shifting mass (crushed meteorites) inside the spacecraft as its spinning in its centrifuge mode. AOSAT 1 will be the first in a series of low-cost CubeSat centrifuges that will be launched setting the stage for a larger, permanent, on-orbit centrifuge laboratory for experiments in planetary science, life sciences and manufacturing.

Autonomous control systems onboard planetary rovers and spacecraft benefit from having cognitive capabilities like learning so that they can adapt to unexpected situations in-situ. Q-learning is a form of reinforcement learning and it has been efficient in solving certain class of learning problems. However, embedded systems onboard planetary rovers and spacecraft rarely implement learning algorithms due to the constraints faced in the field, like processing power, chip size, convergence rate and costs due to the need for radiation hardening. These challenges present a compelling need for a portable, low-power, area efficient hardware accelerator to make learning algorithms practical onboard space hardware. This paper presents a FPGA implementation of Q-learning with Artificial Neural Networks (ANN). This method matches the massive parallelism inherent in neural network software with the fine-grain parallelism of an FPGA hardware thereby dramatically reducing processing time. Mars Science Laboratory currently uses Xilinx-Space-grade Virtex FPGA devices for image processing, pyrotechnic operation control and obstacle avoidance. We simulate and program our architecture on a Xilinx Virtex 7 FPGA. The architectural implementation for a single neuron Q-learning and a more complex Multilayer Perception (MLP) Q-learning accelerator has been demonstrated. The results show up to a 43-fold speed up by Virtex 7 FPGAs compared to a conventional Intel i5 2.3 GHz CPU. Finally, we simulate the proposed architecture using the Symphony simulator and compiler from Xilinx, and evaluate the performance and power consumption.

Current spacecraft need to launch with all of their required fuel for travel. This limits the system performance, payload capacity, and mission flexibility. One compelling alternative is to perform In-Situ Resource Utilization (ISRU) by extracting fuel from small bodies in local space such as asteroids or small satellites. Compared to the Moon or Mars, the microgravity on an asteroid demands a fraction of the energy for digging and accessing hydrated regolith just below the surface. Previous asteroid excavation efforts have focused on discrete capture events (an extension of sampling technology) or whole-asteroid capture and processing. This paper proposes an optimized bucket wheel design for surface excavation of an asteroid or small-body. Asteroid regolith is excavated and water extracted for use as rocket propellant. Our initial study focuses on system design, bucket wheel mechanisms, and capture dynamics applied to ponded materials known to exist on asteroids like Itokawa and Eros and small satellites like Phobos and Deimos. For initial evaluation of material-spacecraft dynamics and mechanics, we assume lunar-like regolith for bulk density, particle size and cohesion. We shall present our estimates for the energy balance of excavation and processing versus fuel gained. Conventional electrolysis of water is used to produce hydrogen and oxygen. It is compared with steam for propulsion and both show significant delta-v. We show that a return trip from Deimos to Earth is possible for a 12 kg craft using ISRU processed fuel.

CubeSats are emerging as low-cost tools to perform astronomy, exoplanet searches and earth observation. These satellites can target an object for science observation for weeks on end. This is typically not possible on larger missions where usage time is shared. The problem of designing an attitude control system for CubeSat telescopes is very challenging because current choice of actuators such as reaction-wheels and magnetorquers can induce jitter on the spacecraft due to moving mechanical parts and due to external disturbances. These telescopes may contain cryo-pumps and servos that introduce additional vibrations. A better solution is required. In our paper, we analyze the feasibility of utilizing solar radiation pressure (SRP) and radiometric force to achieve precise attitude control. Our studies show radiometric actuators to be a viable method to achieve precise pointing. The device uses 8 thin vanes of different temperatures placed in a near-vacuum chamber. These chambers contain trace quantities of lightweight, inert gasses like argon. The temperature gradient across the vanes causes the gas molecules to strike the vanes differently and thus inducing a force. By controlling these forces, it's possible to produce a torque to precisely point or spin a spacecraft. We present a conceptual design of a CubeSat that is equipped with these actuators. We then analyze the potential slew maneuver and slew rates possible with these actuators by simulating their performance. Our analytical and simulation results point towards a promising pathway for laboratory testing of this technology and demonstration of this technology in space.

The miniaturization of electronics, sensors and actuators has enabled the growing use of CubeSats and sub-20 kg spacecraft. Their reduced mass and volume has the potential to translate into significant reductions in required propellant and launch mass for interplanetary missions, earth observation and for astrophysics applications. There is an important need to optimize the design of these spacecraft to better ascertain their maximal capabilities by finding optimized solution, where mass, volume and power is a premium. Current spacecraft design methods require a team of experts, who use their engineering experience and judgement to develop a spacecraft design. Such an approach can miss innovative designs not thought of by a human design team. In this work we present a compelling alternative approach that extends the capabilities of a spacecraft engineering design team to search for and identify near-optimal solutions using machine learning. The approach enables automated design of a spacecraft that requires specifying quantitative goals, requiring reaching a target location or operating at a predetermined orbit for a required time. Next a virtual warehouse of components is specified that be selected to produce a candidate design. Candidate designs are produced using an artificial Darwinian approach, where fittest design survives and reproduce, while unfit individuals are culled off. Our past work in space robotic has produced systems designs and controllers that are human competitive. Finding a near-optimal solution presents vast improvements over a solution obtained through engineering judgment and point design alone. The approach shows a credible pathway to identify and evaluate many more candidate designs than it would be otherwise possible with a human design team alone.

In this paper, a control approach called Artificial Neural Tissue (ANT) is applied to multirobot excavation for lunar base preparation tasks including clearing landing pads and burying of habitat modules. We show for the first time, a team of autonomous robots excavating a terrain to match a given 3D blueprint. Constructing mounds around landing pads will provide physical shielding from debris during launch/landing. Burying a human habitat modules under 0.5 m of lunar regolith is expected to provide both radiation shielding and maintain temperatures of -25 $^{o}$C. This minimizes base life-support complexity and reduces launch mass. ANT is compelling for a lunar mission because it doesn't require a team of astronauts for excavation and it requires minimal supervision. The robot teams are shown to autonomously interpret blueprints, excavate and prepare sites for a lunar base. Because little pre-programmed knowledge is provided, the controllers discover creative techniques. ANT evolves techniques such as slot-dozing that would otherwise require excavation experts. This is critical in making an excavation mission feasible when it is prohibitively expensive to send astronauts. The controllers evolve elaborate negotiation behaviors to work in close quarters. These and other techniques such as concurrent evolution of the controller and team size are shown to tackle problem of antagonism, when too many robots interfere reducing the overall efficiency or worse, resulting in gridlock. While many challenges remain with this technology our work shows a compelling pathway for field testing this approach.