The Schwarzschild-Couder Telescope (SCT) is a candidate technology for a medium-sized telescope within the Cherenkov Telescope Array, the next generation ground based observatory for very high energy gamma ray astronomy. The SCT uses a novel two-mirror design and is expected to yield improvements in field of view and image resolution compared to traditional Cherenkov telescopes based on single-mirror-dish optics. To match the improved optical resolution, challenging requirements of high channel count and density at low power consumption must be overcome by the camera. The prototype camera, currently commissioned and tested on the prototype SCT, has been developed based on millimeter scale SiPM pixels and a custom high density digitizer ASIC, TARGET, to provide 1600 pixels spanning a 2.7 degree field of view while being able to sample nanosecond photon pulses. It is mechanically designed to allow for an upgrade to 11,328 pixels covering a field of view of 8 degrees and demonstrating the full potential of the technology. The camera was installed on the telescope in 2018. We will present its design and performance including first light data.

The Cherenkov Telescope Array (CTA), with more than 100 telescopes, will be the largest ever ground-based gamma-ray observatory and is expected to greatly improve on both gamma-ray detection sensitivity and energy coverage compared to current-generation detectors. The 9.7-m Schwarzschild-Couder telescope (SCT) is one of the two candidates for the medium size telescope (MST) design for CTA. The novel aplanatic dual-mirror SCT design offers a wide field-of-view with a compact plate scale, allowing for a large number of camera pixels that improves the angular resolution and reduce the night sky background noise per pixel compared to the traditional single-mirror Davies-Cotton (DC) design of ground-based gamma-ray telescopes. The production, installation, and the alignment of the segmented aspherical mirrors are the main challenges for the realization of the SCT optical system. In this contribution, we report on the commissioning status, the alignment procedures, and initial alignment results during the initial commissioning phase of the optical system of the prototype SCT.

The Schwarzschild-Couder Telescope (SCT) is a proposal for the Medium Size Telescopes of the Cherenkov Telescope Array. Its concept is based on a two-mirror optical system designed to improve the telescope field of view and image resolution with respect to the single mirror Davies-Cotton solution. The SCT camera is planned to be instrumented with 177 photodetection modules, each composed of 64 Silicon Photomultiplier (SiPM) pixels. The third generation of $6 x 6~mm^2$ high density NUV SiPMs (NUV-HD3) produced by Fondazione Bruno Kessler (FBK) in collaboration with INFN has been used to equip optical units to be integrated on the upgrade of the camera of the SCT prototype (pSCT). Each optical unit is composed of an array of 16 NUV-HD3 SiPMs coupled with the front-end electronics, which is designed for full-waveform nanosecond readout and digitization using the TARGET-7 ASIC. Several optical units have been assembled and tested in the laboratories of INFN and have been integrated on the camera of the pSCT telescope, that is currently operating at the Fred Lawrence Whipple Observatory. In this contribution we report on the development, assembly and calibration of the optical units that are currently taking data on the pSCT camera.

The Cherenkov Telescope Array (CTA) is the major next-generation observatory for ground-based very-high-energy gamma-ray astronomy. It will improve the sensitivity of current ground-based instruments by a factor of five to twenty, depending on the energy, greatly improving both their angular and energy resolutions over four decades in energy (from 20 GeV to 300 TeV). This achievement will be possible by using tens of imaging Cherenkov telescopes of three successive sizes. They will be arranged into two arrays, one per hemisphere, located on the La Palma island (Spain) and in Paranal (Chile). We present here the optimised and final telescope arrays for both CTA sites, as well as their foreseen performance, resulting from the analysis of three different large-scale Monte Carlo productions.

Using survey data and numerical LCDM modeling we establish an optimized fit to the generalized Reduced Void Probability Function, RVPF, of Mikjian used to establish a statistical foundation to any physical process associated with hierarchical clustering. We use a numerical N-body cosmological simulation code, GADGET-2, to investigate the sensitivity of the distribution of voids characterized by the RVPF to a general hierarchical reduced void parameter, a. The void parameter is related to the Levy stability index of the distribution and Fischer critical exponent used in clustering models. We numerically simulate the evolution of the universe from a redshift of z=50 to the current epoch at z=0 in order to generate RVPFs. GADGET-2 is an N-body/smoothed particle hydrodynamics, SPH, code that we ran in MPI parallelizable mode on an HPC Beowulf cluster. The numerical data sets are compared to observational data from the Sloan digital sky Survey, SDSS, CfA, the Deep2 Galaxy Redshift Survey, and the 2dF Survey. We find the best value of the parameter a occurs near the Negative Binomial reduced void probability function but exhibits a departure from perfect scaling over the z values studied.

Light curves in the B, V, and I_c passbands have been obtained for the type II Cepheids V154 in M3 and V42 and V84 in M5. Alternating cycle behavior, similar to that seen among RV Tauri variables, is confirmed for V84. Old and new observations, spanning more than a century, show that V154 has increased in period while V42 has decreased in period. V84, on the other hand, has shown large, erratic changes in period that do not appear to reflect the long term evolution of V84 through the HR diagram.

We present a detailed simulation of the performance of water Cerenkov detectors suitable for use in the Pierre Auger Observatory. Using {\sc geant4}, a flexible object-oriented simulation program, including all known physics processes, has been developed. The program also allows interactive visualization, and can easily be modified for any experimental setup.