The Philae lander of the Rosetta mission, aimed at the in situ investigation of comet 67P/C-G, was deployed to the surface of the comet nucleus on 12 Nov 2014 at 2.99 AU heliocentric distance. The Dust Impact Monitor (DIM) as part of the Surface Electric Sounding and Acoustic Monitoring Experiment (SESAME) on the lander employed piezoelectric detectors to detect the submillimetre- and millimetre-sized dust and ice particles emitted from the nucleus. We determine the upper limit of the ambient flux of particles in the measurement range of DIM based on the measurements performed with the instrument during Philae's descent to its nominal landing site Agilkia at distances of about 22 km, 18 km, and 5 km from the nucleus barycentre and at the final landing site Abydos. The geometric factor of the DIM sensor is calculated assuming an isotropic ambient flux of the submillimetre- and millimetre-sized particles. For the measurement intervals when no particles were detected the maximum true impact rate was calculated by assuming Poisson distribution of the impacts, and it was given as the detection limit at a 95% confidence level. Based on measurements performed with DIM, the upper limit of the flux of particles in the measurement range of the instrument was of the order of $10^{-8}-10^{-7}m^{-2}s^{-1}sr^{-1}$ during descent and $1.6\cdot10^{-9}m^{-2}s^{-1}sr^{-1}$ at Abydos on 13 and 14 Nov 2014. Considering particle speeds below escape velocity, the upper limit for the volume density of particles in the measurement range of DIM was constrained to $10^{-11}m^{-3}-10^{-12}m^{-3}$. Results of the calculations performed with the GIPSI tool on the expected particle fluxes during the descent of Philae were compatible with the non-detection of compact particles by the DIM instrument.

Context. Comets are primitive objects, remnants of the volatile-rich planetesimals from which the solar system condensed. Knowing their structure and composition is thus crucial for the understanding of our origins. After the successful landing of Philae on the nucleus of 67P/Churyumov-Gerasimenko in November 2014, for the first time, the Rosetta mission provided the opportunity to measure the low frequency electrical properties of a cometary mantle with the permittivity probe SESAME-PP (Surface Electric Sounding and Acoustic Monitoring Experiment - Permittivity Probe). Aims. In this paper, we conduct an in-depth analysis of the data from active measurements collected by SESAME-PP at Abydos, which is the final landing site of Philae, to constrain the porosity and, to a lesser extent, the composition of the surface material down to a depth of about 1 meter. Methods. SESAME-PP observations on the surface are then analyzed by comparison with data acquired during the descent toward the nucleus and with numerical simulations that explore different possible attitudes and environments of Philae at Abydos using a method called the Capacity-Influence Matrix Method. Results. Reasonably assuming that the two receiving electrode channels have not drifted with respect to each other during the ten-year journey of the Rosetta probe to the comet, we constrain the dielectric constant of the first meter below the surface at Abydos to be > 2.45 p/m 0.20, which is consistent with a porosity < 50% if the dust phase is analogous to carbonaceous chondrites and < 75% in the case of less primitive ordinary chondrites. This indicates that the near surface of the nucleus of 67P/Churyumov-Gerasimenko nucleus is more compacted than its interior and suggests that it could consist of a sintered dust-ice layer.

The Rosetta lander Philae successfully landed on the nucleus of comet 67P/Churyumov-Gerasimenko on 12 November 2014. Philae carries the Dust Impact Monitor (DIM) on board, which is part of the Surface Electric Sounding and Acoustic Monitoring Experiment (SESAME). DIM employs piezoelectric PZT sensors to detect impacts by sub-millimeter and millimeter-sized ice and dust particles that are emitted from the nucleus and transported into the cometary coma. The DIM sensor measures dynamical data like flux and the directionality of the impacting particles. Mass and speed of the particles can be constrained assuming density and elastic particle properties. DIM was operated during three mission phases of Philae at the comet: (1) Before Philae's separation from Rosetta at distances of about 9.6 km, 11.8 km, and 25.3 km from the nucleus barycenter. In this mission phase particles released from the nucleus on radial trajectories remained undetectable because of significant obscuration by the structures of Rosetta, and no dust particles were indeed detected. (2) During Philae's descent to its nominal landing site Agilkia, DIM detected one approximately millimeter-sized particle at a distance of 5.0 km from the nucleus' barycenter, corresponding to an altitude of 2.4 km from the surface. This is the closest ever dust detection at a cometary nucleus by a dedicated in-situ dust detector. (3) At Philae's final landing site, Abydos, DIM detected no dust impact which may be due to low cometary activity in the vicinity of Philae, or due to shading by obstacles close to Philae, or both. Laboratory calibration experiments showed that the material properties of the detected particle are compatible with a porous particle having a bulk density of approximately $250\, \mathrm{kg\,m^{-3}}$. The particle could have been lifted off from the comet's surface by sublimating water ice.