Next generation radio telescopes, such as the Square Kilometre Array (SKA) and Next Generation Very Large Array (ngVLA), require precise microwave frequency reference signals to be transmitted over fiber links to each dish to coherently sample astronomical signals. Such telescopes employ phase stabilization systems to suppress the phase noise imparted on the reference signals by environmental perturbations on the links; however, the stabilization systems are bandwidth limited by the round-trip time of light travelling on the fiber links. A phase-locked Receiver Module (RM) is employed on each dish to suppress residual phase noise outside of the round-trip bandwidth. The SKA RM must deliver a 3.96 GHz output signal with 4 MHz of tuning range and less than 74 fs of timing jitter. We present an RM architecture to meet both requirements. Analytical modelling of the RM predicts 50 fs of output jitter when the reference signal is integrated between 1 Hz and 2.8 GHz. The proposed RM was conceived with best practice electromagnetic compatibility in mind, and to meet size, weight and power requirements for the SKA dish indexer. As the ngVLA phase stabilization system is currently based on the SKA system, this RM architecture is applicable to the ngVLA.

Doppler orbitography uses the Doppler shift in a transmitted signal to determine the orbital parameters of satellites including range and range-rate (or radial velocity). We describe two techniques for atmospheric-limited optical Doppler orbitography measurements of range-rate. The first determines the Doppler shift directly from a heterodyne measurement of the returned optical signal. The second aims to improve the precision of the first by suppressing atmospheric phase noise imprinted on the transmitted optical signal. We demonstrate the performance of each technique over a 2.2 km horizontal link with a simulated in-line velocity Doppler shift at the far end. A horizontal link of this length has been estimated to exhibit nearly half the total integrated atmospheric turbulence of a vertical link to space. Without stabilisation of the atmospheric effects, we obtained an estimated range rate precision of 17 um/s at 1 s of integration. With active suppression of atmospheric phase noise, this improved by three orders-of-magnitude to an estimated range rate precision of 9.0 nm/s at 1 second of integration, and 1.1 nm/s when integrated over a 60 s. This represents four orders-of-magnitude improvement over the typical performance of operational ground to space X-Band systems in terms of range-rate precision at the same integration time. The performance of this system is a promising proof of concept for coherent optical Doppler orbitography. There are many additional challenges associated with performing these techniques from ground to space, that were not captured within the preliminary experiments presented here. In the future, we aim to progress towards a 10 km horizontal link to replicate the expected atmospheric turbulence for a ground to space link.

This paper describes the technical details and practical implementation of the Mid-Frequency Square Kilometre Array (SKA) phase synchronisation system. Over a four-year period, the system has been tested on metropolitan fibre-optic networks, on long-haul overhead fibre at the South African SKA site, and on existing telescopes in Australia to verify its functional performance. The tests have shown that the system exceed the 1-second SKA coherence loss requirement by a factor 2560, the 60-second coherence loss requirement by a factor of 239, and the 10-minute phase drift requirement by almost five orders-of-magnitude. The paper also reports on tests showing that the system can operate within specification over the all required operating conductions, including maximum fibre link distance, temperature range, temperature gradient, relative humidity, wind speed, seismic resilience, electromagnetic compliance, frequency offset, and other operational requirements.

The Square Kilometre Array (SKA) project is an international effort to build the world's most sensitive radio telescope operating in the 50 MHz to 14 GHz frequency range. Construction of the SKA is divided into phases, with the first phase (SKA1) accounting for the first 10% of the telescope's receiving capacity. During SKA1, a Low-Frequency Aperture Array (LFAA) comprising over a hundred thousand individual dipole antenna elements will be constructed in Western Australia (SKA1-LOW), while an array of 197 parabolic-receptor antennas, incorporating the 64 receptors of MeerKAT, will be constructed in South Africa (SKA1-MID). Radio telescope arrays, such as the SKA, require phase-coherent reference signals to be transmitted to each antenna site in the array. In the case of the SKA, these reference signals are generated at a central site and transmitted to the antenna sites via fibre-optic cables up to 175 km in length. Environmental perturbations affect the optical path length of the fibre and act to degrade the phase stability of the reference signals received at the antennas, which has the ultimate effect of reducing the fidelity and dynamic range of the data . Given the combination of long fibre distances and relatively high frequencies of the transmitted reference signals, the SKA needs to employ actively-stabilised frequency transfer technologies to suppress the fibre-optic link noise in order to maintain phase-coherence across the array.

The Square Kilometre Array (SKA) project is an international effort to build the world's most sensitive radio telescope operating in the 50 MHz to 14 GHz frequency range. Construction of the SKA is divided into phases, with the first phase (SKA1) accounting for the first 10% of the telescope's receiving capacity. During SKA1, a Low-Frequency Aperture Array (LFAA) comprising over a hundred thousand individual dipole antenna elements will be constructed in Western Australia (SKA1-LOW), while an array of 197 parabolic-receptor antennas, incorporating the 64 receptors of MeerKAT, will be constructed in South Africa (SKA1-MID). Radio telescope arrays, such as the SKA, require phase-coherent reference signals to be transmitted to each antenna site in the array. In the case of the SKA, these reference signals are generated at a central site and transmitted to the antenna sites via fibre-optic cables up to 175 km in length. Environmental perturbations affect the optical path length of the fibre and act to degrade the phase stability of the reference signals received at the antennas, which has the ultimate effect of reducing the fidelity and dynamic range of the data . Given the combination of long fibre distances and relatively high frequencies of the transmitted reference signals, the SKA needs to employ actively-stabilised frequency transfer technologies to suppress the fibre-optic link noise in order to maintain phase-coherence across the array.

Aerial suspended optical-fiber links are being considered as economical alternatives to buried links for long-distance transfer of coherent time and frequency signals. We present stability measurements of an actively stabilized 20 MHz photonic signal over aerial fiber links up to 186.2 km in length. Absolute frequency stabilities of 2.7x10^-3 Hz at 1 s of integration, and 2.5x10^-5 Hz at 8x10^3 s of integration are achieved over this longest link. This stability is compared to that achieved over buried links for both radio and microwave frequencies. The results show that aerial fiber links are a suitable alternative to buried links for a wide range of frequency transfer applications.

We describe and experimentally evaluate a stabilized radio-frequency transfer technique that employs optical phase sensing and optical phase actuation. This technique can be achieved by modifying existing stabilized optical frequency equipment and also exhibits advantages over previous stabilized radio-frequency transfer techniques in terms of size and complexity. We demonstrate the stabilized transfer of a 160 MHz signal over an 166 km fiber optical link, achieving an Allan deviation of 9.7x10^-12 Hz/Hz at 1 s of integration, and 3.9x10^-1414 Hz/Hz at 1000 s. This technique is being considered for application to the Square Kilometre Array SKA1-low radio telescope.

HIPSR (HI-Pulsar) is a digital signal processing system for the Parkes 21-cm Multibeam Receiver that provides larger instantaneous bandwidth, increased dynamic range, and more signal processing power than the previous systems in use at Parkes. The additional computational capacity enables finer spectral resolution in wideband HI observations and real-time detection of Fast Radio Bursts during pulsar surveys. HIPSR uses a heterogeneous architecture, consisting of FPGA-based signal processing boards connected via high-speed Ethernet to high performance compute nodes. Low-level signal processing is conducted on the FPGA-based boards, and more complex signal processing routines are conducted on the GPU-based compute nodes. The development of HIPSR was driven by two main science goals: to provide large bandwidth, high-resolution spectra suitable for 21-cm stacking and intensity mapping experiments; and to upgrade the Berkeley-Parkes-Swinburne Recorder (BPSR), the signal processing system used for the High Time Resolution Universe (HTRU) Survey and the Survey for Pulsars and Extragalactic Radio Bursts (SUPERB).

We present a stabilized microwave-frequency transfer technique that is based on optical phase-sensing and optical phase-actuation. This technique shares several attributes with optical-frequency transfer and therefore exhibits several advantages over other microwave-frequency transfer techniques. We demonstrated stabilized transfer of an 8,000 MHz microwave-frequency signal over a 166 km metropolitan optical fiber network, achieving a fractional frequency stability of 6.8x10^-14 Hz/Hz at 1 s integration, and 5.0x10^-16 Hz/Hz at 1.6x10^4 s. This technique is being considered for use on the Square Kilometre Array SKA1-mid radio telescope.

We present measurements of the frequency transfer stability and analysis of the noise characteristics of an optical signal propagating over aerial suspended fiber links up to 153.6 km in length. The measured frequency transfer stability over these links is on the order of 10^-11 at an integration time of one second dropping to 10^-12 for integration times longer than 100 s. We show that wind-loading of the cable spans is the dominant source of short-timescale noise on the fiber links. We also report an attempt to stabilize the optical frequency transfer over these aerial links.

In order to meet its cutting-edge scientific objectives, the Square Kilometre Array (SKA) telescope requires high-precision frequency references to be distributed to each of its antennas. The frequency references are distributed via fiber-optic links and must be actively stabilized to compensate for phase-noise imposed on the signals by environmental perturbations on the links. SKA engineering requirements demand that any proposed frequency reference distribution system be proved in "astronomical verification" tests. We present results of the astronomical verification of a stabilized frequency reference transfer system proposed for SKA-mid. The dual-receiver architecture of the Australia Telescope Compact Array was exploited to subtract the phase-noise of the sky signal from the data, allowing the phase-noise of observations performed using a standard frequency reference, as well as the stabilized frequency reference transfer system transmitting over 77 km of fiber-optic cable, to be directly compared. Results are presented for the fractional frequency stability and phase-drift of the stabilized frequency reference transfer system for celestial calibrator observations at 5 GHz and 25 GHz. These observations plus additional laboratory results for the transferred signal stability over a 166 km metropolitan fiber-optic link are used to show that the stabilized transfer system under test exceeds all SKA phase-stability requirements under a broad range of observing conditions. Furthermore, we have shown that alternative reference dissemination systems that use multiple synthesizers to supply reference signals to sub-sections of an array may limit the imaging capability of the telescope.

We present direct upper limits on gravitational wave emission from the Crab pulsar using data from the first nine months of the fifth science run of the Laser Interferometer Gravitational-wave Observatory (LIGO). These limits are based on two searches. In the first we assume that the gravitational wave emission follows the observed radio timing, giving an upper limit on gravitational wave emission that beats indirect limits inferred from the spin-down and braking index of the pulsar and the energetics of the nebula. In the second we allow for a small mismatch between the gravitational and radio signal frequencies and interpret our results in the context of two possible gravitational wave emission mechanisms.