Global coronal waves (CWs) and their interaction with coronal holes (CHs) result, among other effects, in the formation of reflected and transmitted waves. Observations of such events provide us with measurements of different CW parameters, such as phase speed and intensity amplitudes. However, several of these parameters are provided with only intermediate observational quality, other parameters, such as the phase speed of transmitted waves, can hardly be observed in general. We present a new method to estimate crucial CW parameters, such as density and phase speed of reflected as well as transmitted waves, Mach numbers and density values of the CH's interior, by using analytical expressions in combination with basic and most accessible observational measurements. The transmission and reflection coefficients are derived from linear theory and subsequently used to calculate estimations for phase speeds of incoming, reflected and transmitted waves. The obtained analytical expressions are validated by performing numerical simulations of CWs interacting with CHs. This new method enables to determine in a fast and straightforward way reliable CW and CH parameters from basic observational measurements which provides a powerful tool to better understand the observed interaction effects between CWs and CHs.

We used our newly developed magnetohydrodynamic (MHD) code to perform 2.5D simulations of a fast-mode MHD wave interacting with coronal holes (CH) of varying Alfv\'en speed which result from assuming different CH densities. We find that this interaction leads to effects like reflection, transmission, stationary fronts at the CH boundary and the formation of a density depletion that moves in the opposite direction to the incoming wave. We compare these effects with regard to the different CH densities and present a comprehensive analysis of morphology and kinematics of the associated secondary waves. We find that the density value inside the CH influences the phase speed as well as the amplitude values of density and magnetic field for all different secondary waves. Moreover, we observe a correlation between the CH density and the peak values of the stationary fronts at the CH boundary. The findings of reflection and transmission on the one hand and the formation of stationary fronts caused by the interaction of MHD waves with CHs on the other hand, strongly support the theory that large scale disturbances in the corona are fast-mode MHD waves.

We performed 2.5D magnetohydrodynamic (MHD) simulations showing the propagation of fast-mode MHD waves of different initial amplitudes and their interaction with a coronal hole (CH), using our newly developed numerical code. We find that this interaction results in, first, the formation of reflected, traversing and transmitted waves (collectively, secondary waves) and, second, in the appearance of stationary features at the CH boundary. Moreover, we observe a density depletion that is moving in the opposite direction to the incoming wave. We find a correlation between the initial amplitude of the incoming wave and the amplitudes of the secondary waves as well as the peak values of the stationary features. Additionally, we compare the phase speed of the secondary waves and the lifetime of the stationary features to observations. Both effects obtained in the simulation, the evolution of secondary waves, as well as the formation of stationary fronts at the CH boundary, strongly support the theory that coronal waves are fast-mode MHD waves.

We developed a new numerical code that is able to perform 2.5D simulations of a magnetohydrodynamic (MHD) wave propagation in the corona, and its interaction with a low density region, such as a coronal hole (CH). We show that the impact of the wave on the CH leads to different effects, such as reflection and transmission of the incoming wave, stationary features at the CH boundary, or formation of a density depletion. We present a comprehensive analysis of the morphology and kinematics of primary and secondary waves, that is, we describe in detail the temporal evolution of density, magnetic field, plasma flow velocity, phase speed and position of the wave amplitude. Effects like reflection, refraction and transmission of the wave strongly support the theory that large scale disturbances in the corona are fast MHD waves and build the major distinction to the competing pseudo-wave theory. The formation of stationary bright fronts was one of the main reasons for the development of pseudo-waves. Here we show that stationary bright fronts can be produced by the interactions of an MHD wave with a CH. We find secondary waves that are traversing through the CH and we show that one part of these traversing waves leaves the CH again, while another part is being reflected at the CH boundary inside the CH. We observe a density depletion that is moving in the opposite direction of the primary wave propagation. We show that the primary wave pushes the CH boundary to the right, caused by the wave front exerting dynamic pressure on the CH.

The drag-based model (DBM) for heliospheric propagation of coronal mass ejections (CMEs) is a widely used analytical model which can predict CME arrival time and speed at a given heliospheric location. It is based on the assumption that the propagation of CMEs in interplanetary space is solely under the influence of magnetohydrodynamical drag, where CME propagation is determined based on CME initial properties as well as the properties of the ambient solar wind. We present an upgraded version, covering ensemble modelling to produce a distribution of possible ICME arrival times and speeds, the drag-based ensemble model (DBEM). Multiple runs using uncertainty ranges for the input values can be performed in almost real-time, within a few minutes. This allows us to define the most likely ICME arrival times and speeds, quantify prediction uncertainties and determine forecast confidence. The performance of the DBEM is evaluated and compared to that of ensemble WSA-ENLIL+Cone model (ENLIL) using the same sample of events. It is found that the mean error is $ME=-9.7$ hours, mean absolute error $MAE=14.3$ hours and root mean square error $RMSE=16.7$ hours, which is somewhat higher than, but comparable to ENLIL errors ($ME=-6.1$ hours, $MAE=12.8$ hours and $RMSE=14.4$ hours). Overall, DBEM and ENLIL show a similar performance. Furthermore, we find that in both models fast CMEs are predicted to arrive earlier than observed, most probably owing to the physical limitations of models, but possibly also related to an overestimation of the CME initial speed for fast CMEs.

Previous studies have discovered a population of small granules with diameters less than 800 km showing differing physical properties. High resolution simulations and observations of the solar granulation, in combination with automated segmentation and tracking algorithms, allow us to study the evolution of the structural and physical properties of these granules and surrounding vortex motions with high temporal and spatial accuracy. We focus on the dynamics of granules (lifetime, fragmentation, size, position, intensity, vertical velocity) over time and the influence of strong vortex motions. Of special interest are the dynamics of small granules compared to regular-sized granules. We developed a temporal tracking algorithm based on our developed segmentation algorithm for solar granulation. This was applied to radiation hydrodynamics simulations and high resolution observations of the quiet Sun by SUNRISE/IMaX. The dynamics of small granules differ in regard to their diameter, intensity and depth evolution compared to regular granules. The tracked granules in the simulation and observations reveal similar dynamics (lifetime, evolution of size, vertical velocity and intensity). The fragmentation analysis shows that the majority of granules in simulations do not fragment, while the opposite was found in observations. Strong vortex motions were detected at the location of small granules. Regions of strong vertical vorticity show high intensities and downflow velocities, and live up to several minutes. The analysis of granules separated according to their diameter in different groups reveals strongly differing behaviors. The largest discrepancies can be found within the groups of small, medium-sized and large granules and have to be analyzed independently. The predominant location of vortex motions on and close to small granules indicates a strong influence on the dynamics of granules.