Magnetic reconnection is a process whereby magnetic field lines in different directions "reconnect" with each other, resulting in the rearrangement of magnetic field topology together with the conversion of magnetic field energy into the kinetic energy (K.E.) of energetic particles. This process occurs in magnetized astronomical plasmas, such as those in the solar corona, Earth's magnetosphere, and active galactic nuclei, and accounts for various phenomena, such as solar flares, energetic particle acceleration, and powering of photon emission. In the present study, we report the experimental demonstration of magnetic reconnection under relativistic electron magnetization situation, along with the observation of power-law distributed outflow in both electron and proton energy spectra. Through irradiation of an intense laser on a "micro-coil", relativistically magnetized plasma was produced and magnetic reconnection was performed with maximum magnetic field 3 kT. In the downstream outflow direction, the non-thermal component is observed in the high-energy part of both electron and proton spectra, with a significantly harder power-law slope of the electron spectrum (p = 1.535 +/- 0.015) that is similar to the electron injection model proposed to explain a hard emission tail of Cygnus X-1, a galactic X-ray source with the same order of magnetization. The obtained result showed experimentally that the magnetization condition in the emitting region of a galactic X-ray source is sufficient to build a hard electron population through magnetic reconnection.

This paper presents highly precise measurements of thermal expansion of a "hybrid" carbon-fiber reinforced silicon carbide composite, HB-Cesic\textregistered - a trademark of ECM, in the temperature region of \sim310-10K. Whilst C/SiC composites have been considered to be promising for the mirrors and other structures of space-borne cryogenic telescopes, the anisotropic thermal expansion has been a potential disadvantage of this material. HB-Cesic\textregistered is a newly developed composite using a mixture of different types of chopped, short carbon-fiber, in which one of the important aims of the development was to reduce the anisotropy. The measurements indicate that the anisotropy was much reduced down to 4% as a result of hybridization. The thermal expansion data obtained are presented as functions of temperature using eighth-order polynomials separately for the horizontal (XY-) and vertical (Z-) directions of the fabrication process. The average CTEs and their dispersion (1{\sigma}) in the range 293-10K derived from the data for the XY- and Z-directions were 0.805$\pm$0.003\times10$^{-6}$ K$^{-1}$ and 0.837\pm0.001\times10$^{-6}$ K$^{-1}$, respectively. The absolute accuracy and the reproducibility of the present measurements are suggested to be better than 0.01\times10$^{-6}$ K$^{-1}$ and 0.001\times(10)^{-6} K^{-1}, respectively. The residual anisotropy of the thermal expansion was consistent with our previous speculation regarding carbon-fiber, in which the residual anisotropy tended to lie mainly in the horizontal plane.

We report on the microscopic surface structure of carbon-fiber-reinforced silicon carbide (C/SiC) composite mirrors that have been improved for the Space Infrared Telescope for Cosmology and Astrophysics (SPICA) and other cooled telescopes. The C/SiC composite consists of carbon fiber, silicon carbide, and residual silicon. Specific microscopic structures are found on the surface of the bare C/SiC mirrors after polishing. These structures are considered to be caused by the different hardness of those materials. The roughness obtained for the bare mirrors is 20 nm rms for flat surfaces and 100 nm rms for curved surfaces. It was confirmed that a SiSiC slurry coating is effective in reducing the roughness to 2 nm rms. The scattering properties of the mirrors were measured at room temperature and also at 95 K. No significant change was found in the scattering properties through cooling, which suggests that the microscopic surface structure is stable with changes in temperature down to cryogenic values. The C/SiC mirror with the SiSiC slurry coating is a promising candidate for the SPICA telescope.