Inelastic collisions occur among regolith particles, such as those in the ejecta curtain from a crater, and may cause clustering or agglomeration of particles and thus produce discrete patterns of ejecta deposits around a crater. Previous studies have shown that clusters, and even agglomerates, are formed via mutual, inelastic collisions of spherical particles due to adhering forces between particles in granular streams. To investigate the condition of agglomerate formation in granular streams, we conducted laboratory experiments of granular streams using both spherical and irregular, non-spherical particles. Measurements of particle adhesion in this study were performed using a centrifugal separation method, in contrast to the previous study in which atomic force microscopy (AFM) was used. This enabled simultaneous measurements of multiple particles of various shapes for a statistical analysis of the results. With similar relative velocities and adhesion values, irregular particles were found to form agglomerates much more easily than spherical particles. The axial ratio of the agglomerates of spherical particles and irregular particles was similar and was in accordance with those observed in previous laboratory studies, whereas the size of the agglomerates of irregular particles was larger than the size of spherical particles. The degree of agglomeration and the size of agglomerates can be used as an indicator of the shape or adhesive force of the particles in granular stream. Our findings on agglomeration in granular streams could provide new insights into the origin of rays on airless bodies and grooves on Phobos.

The porosity structure of a granular body is an important characteristic that affects evolutionary changes in the body. We conducted compression experiments using fluffy granular samples with various particle sizes, shapes, and compositions. We approximated the pressure-filling factor relationship of each sample with a power law (a modified polytropic relationship). We also fit our previous data and literature data for fluffy granular samples using a power-law equation. The fitting with a power-law form was as good as that achieved with the equations used for powders in previous studies. The polytropic indices obtained in the current study ranged from ~0.01 to ~0.3 and tended to decrease with increasing particle size for samples of similar porosities. We calculated the radial porosity structure and bulk porosity of granular bodies with various radii using the Lane-Emden equation. The results provide the initial, most porous structures of accreted primordial bodies, or re-accumulated rubble-pile bodies consisting of particles that have compression properties similar to those of the assumed granular materials. A range of porosity structures is allowed for a body of given size and macroporosity, depending on the compression properties of the constituent granular material.

Porosity is a key characteristic of the regolith on the surface of small bodies. The porosity of the regolith on the surface of asteroids is changed by applied pressure, and the relationship between pressure and porosity depends on the particle properties of the regolith. We performed compression measurements on samples of different materials, particle size distributions, and shapes to examine the relationship between particle size and pressure required for compression. We used a centrifuge and a compression testing machine for the experiments. The applied pressure for the centrifuge and the compression testing machine experiments ranged from 10^2 to 5x10^3 Pa and from 10^4 to 5x10^6 Pa, respectively. The initial porosity before compression was generally higher for samples with smaller particles and narrower particle size distributions. A sample compressed more easily when it consisted of smaller particles, probably due to smaller frictional forces between particles. We estimated the porosity of granular asteroids based on the results of our experiments. The estimated porosity at the center of a homogeneous asteroid with a radius of 50 km is 0.43. This porosity is typical of the porosity of asteroids of similar size.

The compression property of regolith reflects the strength and porosity of the regolith layer on small bodies and their variations in the layer that largely influence the collisional and thermal evolution of the bodies. We conducted compression experiments and investigated the relationship between the porosity and the compression using fluffy granular samples. We focused on a low-pressure and high-porosity regime. We used tens of {\mu}m-sized irregular and spherical powders as analogs of porous regolith. The initial porosity of the samples ranged from 0.80 to 0.53. The uniaxial pressure applied to the samples lays in the range from 30 to 4x10^5 Pa. The porosity of the samples remained at their initial values below a threshold pressure and then decreased when the pressure exceeded the threshold. We defined this uniaxial pressure at the threshold as "yield strength". The yield strength increased as the initial porosity of a sample decreased. The yield strengths of samples consisting of irregular particles did not significantly depend on their size distributions when the samples had the same initial porosity. We compared the results of our experiments with a previously proposed theoretical model. We calculated the average interparticle force acting on contact points of constituent particles under the uniaxial pressure of yield strength using the theoretical model and compared it with theoretically estimated forces required to roll or slide the particles. The calculated interparticle force was larger than the rolling friction force and smaller than the sliding friction force. The yield strength of regolith may be constrained by these forces. Our results may be useful for planetary scientists to estimate the depth above which the porosity of a regolith layer is almost equal to that of the regolith surface and to interpret the compression property of an asteroid surface obtained by a lander.