High-contrast imaging (HCI) observations of exoplanets can be limited by the island effect (IE). On the current generation of telescopes, the IE becomes a severe problem when the ground wind speed is below a few meters per second. This is referred to as the low-wind effect (LWE). The LWE severely distorts the point spread function (PSF), significantly lowering the Strehl ratio and degrading the contrast. In this article, we aim to show that the focal-plane wavefront sensing (FPWFS) algorithm, Fast and Furious (F&F), can be used to measure and correct the IE/LWE. We deployed the algorithm on the SCExAO HCI instrument at the Subaru Telescope using the internal near-infrared camera in H-band. We tested F&F with the internal source, and it was deployed on-sky to test its performance with the full end-to-end system and atmospheric turbulence. The performance of the algorithm was evaluated by two metrics based on the PSF quality: 1) the Strehl ratio approximation ($SRA$), and 2) variance of the normalized first Airy ring ($VAR$). Random LWE phase screens with a peak-to-valley wavefront error between 0.4 $\mu$m and 2 $\mu$m were all corrected to a $SRA$ $>$90\% and an $VAR\lessapprox0.05$. Furthermore, the on-sky results show that F&F is able to improve the PSF quality during very challenging atmospheric conditions (1.3-1.4'' seeing at 500 nm). Closed-loop tests show that F&F is able to improve the $VAR$ from 0.27 to 0.03 and therefore significantly improve the symmetry of the PSF. Simultaneous observations of the PSF in the {optical} ($\lambda = $ 750 nm, $\Delta \lambda =$ 50 nm) show that during these tests we were correcting aberrations common to the optical and NIR paths within SCExAO. Going forward, the algorithm is suitable for incorporation into observing modes, which will enable PSFs of higher quality and stability during science observations.

Adaptive optics (AO) is critical in modern astronomy, as well as in optical communications and remote sensing, to deal with the rapid blurring caused by the Earth's turbulent atmosphere. But even the best AO systems are limited by their wavefront sensors, which need to be in an optical plane non-common to the science image, unavoidably leading to errors that limit the reach of current astronomy. They are also insensitive to certain wavefront-error modes, and are poorly suited to injecting light into single-mode optical fibres, important for applications such as high-resolution spectroscopy of extra-solar planets. Here we present a new type of wavefront sensor based on a photonic lantern fibre-mode-converter and deep learning. This new wavefront sensor can be placed at the same focal plane as the science image, and is also optimal for single-mode fibre injection. By only measuring the intensities of an array of single-mode outputs, both phase and amplitude information on the incident wavefront can be reconstructed. We demonstrate the concept with both simulations and an experimental realisation of this novel wavefront sensor, wherein Zernike wavefront errors are recovered from focal-plane measurements to a precision of $2.6\times10^{-5}$ radians mean-squared-error.

The Low Wind Effect (LWE) refers to a phenomenon that occurs when the wind speed inside a telescope dome drops below $3$m/s creating a temperature gradient near the telescope spider. This produces phase discontinuities in the pupil plane that are not detected by traditional Adaptive Optics (AO) systems such as the pyramid wavefront sensor or the Shack-Hartmann. Considering the pupil as divided in 4 quadrants by regular spiders, the phase discontinuities correspond to piston, tip and tilt aberrations in each quadrant of the pupil. Uncorrected, it strongly decreases the ability of high contrast imaging instruments utilizing coronagraphy to detect exoplanets at small angular separations. Multiple focal plane wavefront sensors are currently being developed and tested on the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument at Subaru Telescope: Among them, the Zernike Asymmetric Pupil (ZAP) wavefront sensor already showed on-sky that it could measure the LWE induced aberrations in focal plane images. The Fast and Furious algorithm, using previous deformable mirror commands as temporal phase diversity, showed in simulations its efficiency to improve the wavefront quality in the presence of LWE. A Neural Network algorithm trained with SCExAO telemetry showed promising PSF prediction on-sky. The Linearized Analytic Phase Diversity (LAPD) algorithm is a solution for multi-aperture cophasing and is studied to correct for the LWE aberrations by considering the Subaru Telescope as a 4 sub-aperture instrument. We present the different algorithms, show the latest results and compare their implementation on SCExAO/SUBARU as real-time wavefront sensors for the LWE compensation.

The characterisation of exoplanets is critical to understanding planet diversity and formation, their atmospheric composition and the potential for life. This endeavour is greatly enhanced when light from the planet can be spatially separated from that of the host star. One potential method is nulling interferometry, where the contaminating starlight is removed via destructive interference. The GLINT instrument is a photonic nulling interferometer with novel capabilities that has now been demonstrated in on-sky testing. The instrument fragments the telescope pupil into sub-apertures that are injected into waveguides within a single-mode photonic chip. Here, all requisite beam splitting, routing and recombination is performed using integrated photonic components. We describe the design, construction and laboratory testing of our GLINT pathfinder instrument. We then demonstrate the efficacy of this method on sky at the Subaru Telescope, achieving a null-depth precision on sky of $\sim10^{-4}$ and successfully determining the angular diameter of stars (via their null-depth measurements) to milli-arcsecond accuracy. A statistical method for analysing such data is described, along with an outline of the next steps required to deploy this technique for cutting-edge science.

Astronomers have come to recognize the benefits of photonics, often in combination with optical systems, in solving longstanding experimental problems in Earth-based astronomy. Here, we explore some of the recent advances made possible by integrated photonics. We also look to the future with a view to entirely new kinds of astronomy, particularly in an era of the extremely large telescopes.

Theory surrounding the origin of the dust-laden winds from evolved stars remains mired in controversy. Characterizing the formation loci and the dust distribution within approximately the first stellar radius above the surface is crucial for understanding the physics that underlie the mass-loss phenomenon. By exploiting interferometric polarimetry, we derive the fundamental parameters that govern the dust structure at the wind base of a red supergiant. We present near-infrared aperture-masking observations of Betelgeuse in polarimetric mode obtained with the NACO/SAMPol instrument. We used both parametric models and radiative transfer simulations to predict polarimetric differential visibility data and compared them to SPHERE/ZIMPOL measurements. Using a thin dust shell model, we report the discovery of a dust halo that is located at only 0.5 R$_{\star}$ above the photosphere (i.e. an inner radius of the dust halo of 1.5 R$_{\star}$). By fitting the data under the assumption of Mie scattering, we estimate the grain size and density for various dust species. By extrapolating to the visible wavelengths using radiative transfer simulations, we compare our model with SPHERE/ZIMPOL data and find that models based on dust mixtures that are dominated by forsterite are most favored. Such a close dusty atmosphere has profound implications for the dust formation mechanisms around red supergiants.

Astrophotonics is the application of versatile photonic technologies to channel, manipulate, and disperse guided light from one or more telescopes to achieve scientific objectives in astronomy in an efficient and cost-effective way. The developments and demands from the telecommunication industry have driven a major boost in photonic technology and vice versa in the last 40 years. The photonic platform of guided light in fibers and waveguides has opened the doors to next-generation instrumentation for both ground- and space-based telescopes in optical and near/mid-IR bands, particularly for the upcoming extremely large telescopes (ELTs). The large telescopes are pushing the limits of adaptive optics to reach close to a near-diffraction-limited performance. The photonic devices are ideally suited for capturing this AO-corrected light and enabling new and exciting science such as characterizing exoplanet atmospheres. The purpose of this white paper is to summarize the current landscape of astrophotonic devices and their scientific impact, highlight the key issues, and outline specific technological and organizational approaches to address these issues in the coming decade and thereby enable new discoveries as we embark on the era of extremely large telescopes.

We present designs for fully achromatic vector Apodizing Phase Plate (vAPP) coronagraphs, that implement low polarization leakage solutions and achromatic beam-splitting, enabling observations in broadband filters. The vAPP is a pupil plane optic, inducing the phase through the inherently achromatic geometric phase. We discuss various implementations of the broadband vAPP and set requirements on all the components of the broadband vAPP coronagraph to ensure that the leakage terms do not limit a raw contrast of 1E-5. Furthermore, we discuss superachromatic QWPs based of liquid crystals or quartz/MgF2 combinations, and several polarizer choices. As the implementation of the (broadband) vAPP coronagraph is fully based on polarization techniques, it can easily be extended to furnish polarimetry by adding another QWP before the coronagraph optic, which further enhances the contrast between the star and a polarized companion in reflected light. We outline several polarimetric vAPP system designs that could be easily implemented in existing instruments, e.g. SPHERE and SCExAO.

The massive evolved Wolf-Rayet stars sometimes occur in colliding-wind binary systems in which dust plumes are formed as a result of the collision of stellar winds. These structures are known to encode the parameters of the binary orbit and winds. Here, we report observations of a previously undiscovered Wolf-Rayet system, 2XMM J160050.7-514245, with a spectroscopically determined wind speed of $\approx$3400 km s$^{-1}$. In the thermal infrared, the system is adorned with a prominent $\approx$12$''$ spiral dust plume, revealed by proper motion studies to be expanding at only $\approx$570 km s$^{-1}$. As the dust and gas appear coeval, these observations are inconsistent with existing models of the dynamics of such colliding wind systems. We propose that this contradiction can be resolved if the system is capable of launching extremely anisotropic winds. Near-critical stellar rotation is known to drive such winds, suggesting this Wolf-Rayet system as a potential Galactic progenitor system for long-duration gamma-ray bursts.

Vibrations are a key source of image degradation in ground-based instrumentation, especially for high-contrast imaging instruments. Vibrations reduce the quality of the correction provided by the adaptive optics system, blurring the science image and reducing the sensitivity of most science modules. We studied vibrations using the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument at the Subaru Telescope as it is the most vibration sensitive system installed on the telescope. We observed vibrations for all targets, usually at low frequency, below 10 Hz. Using accelerometers on the telescope, we confirmed that these vibrations were introduced by the telescope itself, and not the instrument. It was determined that they were related to the pitch of the encoders of the telescope drive system, both in altitude and azimuth, with frequencies evolving proportionally to the rotational speed of the telescope. Another strong vibration was found in the altitude axis of the telescope, around the time of transit of the target, when the altitude rotation speed is below 0.12 arcsec/s. These vibrations are amplified by the 10-Hz control loop of the telescope, especially in a region between 4 and 6 Hz. In this work, we demonstrate an accurate characterization of the frequencies of the telescope vibrations using only the coordinates -right ascension and declination- of the target, and provide a means by which we can predict them for any telescope pointing. This will be a powerful tool that can be used by more advanced wavefront control algorithms, especially predictive control, that uses informations about the disturbance to calculate the best correction.

The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument is an extremely modular high-contrast instrument installed on the Subaru telescope in Hawaii. SCExAO has a dual purpose. Its position in the northern hemisphere on a 8-meter telescope makes it a prime instrument for the detection and characterization of exoplanets and stellar environments over a large portion of the sky. In addition, SCExAO's unique design makes it the ideal instrument to test innovative technologies and algorithms quickly in a laboratory setup and subsequently deploy them on-sky. SCExAO benefits from a first stage of wavefront correction with the facility adaptive optics AO188, and splits the 600-2400 nm spectrum towards a variety of modules, in visible and near infrared, optimized for a large range of science cases. The integral field spectrograph CHARIS, with its J, H or K-band high-resolution mode or its broadband low-resolution mode, makes SCExAO a prime instrument for exoplanet detection and characterization. Here we report on the recent developments and scientific results of the SCExAO instrument. Recent upgrades were performed on a number of modules, like the visible polarimetric module VAMPIRES, the high-performance infrared coronagraphs, various wavefront control algorithms, as well as the real-time controller of AO188. The newest addition is the 20k-pixel Microwave Kinetic Inductance Detector (MKIDS) Exoplanet Camera (MEC) that will allow for previously unexplored science and technology developments. MEC, coupled with novel photon-counting speckle control, brings SCExAO closer to the final design of future high-contrast instruments optimized for Giant Segmented Mirror Telescopes (GSMTs).

Sparse Aperture Masking (SAM) allows for high-contrast imaging at small inner working angles, however the performance is limited by the small throughput and the number of baselines. We present the concept and first lab results of Holographic Aperture Masking (HAM) with extreme liquid-crystal geometric phase patterns. We multiplex subapertures using holographic techniques to combine the same subaperture in multiple non-redundant PSFs in combination with a non-interferometric reference spot. This way arbitrary subaperture combinations and PSF configurations can be realized, giving HAM more uv-coverage, better throughput and improved calibration as compared to SAM, at the cost of detector space.

We present the first-ever images of the circumstellar environment of the carbon-rich AGB star II Lup in the infrared and sub-mm wavelengths, and the discovery of the envelope's non-spherical morphology with the use of high-angular resolution imaging techniques with the sparse aperture masking mode on NACO/VLT (that enables diffraction limited resolution from a single telescope) and with ALMA. We have successfully recovered images in $Ks$ (2.18$\mu$m), $L'$ (3.80$\mu$m) and $M'$ (4.78$\mu$m), that revealed the non-spherical morphology of the circumstellar envelope around II Lup. The stellar surface of the AGB star is unresolved (i.e. $\leq30$ mas in $Ks$) however the detected structure extends up to 110 mas from the star in all filters. Clumps have been found in the $Ks$ maps, while at lower emission levels a hook-like structure appears to extend counter-clockwise from the south. At larger spatial scales, the circumstellar envelope extends up to approximately 23 arcsec, while its shape suggests a spiral at four different molecules, namely CO, SiO, CS and HC$_3$N, with an average arm spacing of 1.7 arcsec which would imply an orbital period of 128 years for a distance of 590pc.

Hi-5 is a high-contrast (or high dynamic range) infrared imager project for the VLTI. Its main goal is to characterize young extra-solar planetary systems and exozodiacal dust around southern main-sequence stars. In this paper, we present an update of the project and key technology pathways to improve the contrast achieved by the VLTI. In particular, we discuss the possibility to use integrated optics, proven in the near-infrared, in the thermal near-infrared (L and M bands, 3-5~$\mu$m) and advanced fringe tracking strategies. We also address the strong exoplanet science case (young exoplanets, planet formation, and exozodiacal disks) offered by this wavelength regime as well as other possible science cases such as stellar physics (fundamental parameters and multiplicity) and extragalactic astrophysics (active galactic nuclei and fundamental constants). Synergies and scientific preparation for other potential future instruments such as the Planet Formation Imager are also briefly discussed.

The Optimal Optical CoronagraphWorkshop at the Lorentz Center in September 2017 in Leiden, the Netherlands gathered a diverse group of 25 researchers working on exoplanet instrumentation to stimulate the emergence and sharing of new ideas. This contribution is the final part of a series of three papers summarizing the outcomes of the workshop, and presents an overview of novel optical technologies and systems that are implemented or considered for high-contrast imaging instruments on both ground-based and space telescopes. The overall objective of high contrast instruments is to provide direct observations and characterizations of exoplanets at contrast levels as extreme as 10^-10. We list shortcomings of current technologies, and identify opportunities and development paths for new technologies that enable quantum leaps in performance. Specifically, we discuss the design and manufacturing of key components like advanced deformable mirrors and coronagraphic optics, and their amalgamation in "adaptive coronagraph" systems. Moreover, we discuss highly integrated system designs that combine contrast-enhancing techniques and characterization techniques (like high-resolution spectroscopy) while minimizing the overall complexity. Finally, we explore extreme implementations using all-photonics solutions for ground-based telescopes and dedicated huge apertures for space telescopes.

The development of high-contrast capabilities has long been recognized as one of the top priorities for the VLTI. As of today, the VLTI routinely achieves contrasts of a few 10$^{-3}$ in the near-infrared with PIONIER (H band) and GRAVITY (K band). Nulling interferometers in the northern hemisphere and non-redundant aperture masking experiments have, however, demonstrated that contrasts of at least a few 10$^{-4}$ are within reach using specific beam combination and data acquisition techniques. In this paper, we explore the possibility to reach similar or higher contrasts on the VLTI. After reviewing the state-of-the-art in high-contrast infrared interferometry, we discuss key features that made the success of other high-contrast interferometric instruments (e.g., integrated optics, nulling, closure phase, and statistical data reduction) and address possible avenues to improve the contrast of the VLTI by at least one order of magnitude. In particular, we discuss the possibility to use integrated optics, proven in the near-infrared, in the thermal near-infrared (L and M bands, 3-5 $\mu$m), a sweet spot to image and characterize young extra-solar planetary systems. Finally, we address the science cases of a high-contrast VLTI imaging instrument and focus particularly on exoplanet science (young exoplanets, planet formation, and exozodiacal disks), stellar physics (fundamental parameters and multiplicity), and extragalactic astrophysics (active galactic nuclei and fundamental constants). Synergies and scientific preparation for other potential future instruments such as the Planet Formation Imager are also briefly discussed.

Spectroscopic observations are extremely important for determining the composition, structure, and surface gravity of exoplanetary atmospheres. High resolution spectroscopy of the planet itself has only been demonstrated a handful of times. By using advanced high contrast imagers, it is possible to conduct high resolution spectroscopy on imageable exoplanets, after the star light is first suppressed with an advanced coronagraph. Because the planet is spatially separated in the focal plane, a single mode fiber could be used to collect the light from the planet alone, reducing the photon noise by orders of magnitude. In addition, speckle control applied to the location where an exoplanet is known to exist, can be used to preferentially reject the stellar flux from the fiber further. In this paper we will present the plans for conducting high resolution spectroscopic studies of this nature with the combination of SCExAO and IRD in the H-band on the Subaru Telescope. This technique will be critical to the characterization of terrestrial planets on ELTs and future space missions.

A suite of science instruments is critical to any high contrast imaging facility, as it defines the science capabilities and observing modes available. SCExAO uses a modular approach which allows for state-of-the-art visitor modules to be tested within an observatory environment on an 8-m class telescope. This allows for rapid prototyping of new and innovative imaging techniques that otherwise take much longer in traditional instrument design. With the aim of maturing science modules for an advanced high contrast imager on an giant segmented mirror telescopes (GSMTs) that will be capable of imaging terrestrial planets, we offer an overview and status update on the various science modules currently under test within the SCExAO instrument.

Island effect (IE) aberrations are induced by differential pistons, tips, and tilts between neighboring pupil segments on ground-based telescopes, which severely limit the observations of circumstellar environments on the recently deployed exoplanet imagers (e.g., VLT/SPHERE, Gemini/GPI, Subaru/SCExAO) during the best observing conditions. Caused by air temperature gradients at the level of the telescope spiders, these aberrations were recently diagnosed with success on VLT/SPHERE, but so far no complete calibration has been performed to overcome this issue. We propose closed-loop focal plane wavefront control based on the asymmetric Fourier pupil wavefront sensor (APF-WFS) to calibrate these aberrations and improve the image quality of exoplanet high-contrast instruments in the presence of the IE. Assuming the archetypal four-quadrant aperture geometry in 8m class telescopes, we describe these aberrations as a sum of the independent modes of piston, tip, and tilt that are distributed in each quadrant of the telescope pupil. We calibrate these modes with the APF-WFS before introducing our wavefront control for closed-loop operation. We perform numerical simulations and then experimental tests on a real system using Subaru/SCExAO to validate our control loop in the laboratory and on-sky. Closed-loop operation with the APF-WFS enables the compensation for the IE in simulations and in the laboratory for the small aberration regime. Based on a calibration in the near infrared, we observe an improvement of the image quality in the visible range on the SCExAO/VAMPIRES module with a relative increase in the image Strehl ratio of 37%. Our first IE calibration paves the way for maximizing the science operations of the current exoplanet imagers. Such an approach and its results prove also very promising in light of the Extremely Large Telescopes (ELTs) and the presence of similar artifacts.

HD 100546 is one of the few known pre-main-sequence stars that may host a planetary system in its disk. We analyze new VLT/SPHERE/ZIMPOL polarimetric images of HD 100546 with filters in H$\alpha$ and the adjacent continuum. We have probed the disk gap and the surface layers of the outer disk, covering a region < 500 mas (< 55 au at 109 pc) from the star, at an angular resolution of ~ 20 mas. Our data show an asymmetry: the SE and NW regions of the outer disk are more polarized than the SW and NE. This can be explained from a preferential scattering angle close to 90$^o$, consistent with previous polarization images. The outer disk extends from 13 $\pm$ 2 to 45 $\pm$ 9 au, with a position angle and inclination of 137 $\pm$ 5$^o$ and 44 $\pm$ 8$^o$. The comparison with previous estimates suggests that the disk inclination could increase with the stellocentric distance, although the different measurements are still consistent within the error bars. In addition, no direct signature of the innermost candidate companion is detected from polarimetry, confirming recent results based on intensity imagery. We set an upper limit to its mass accretion rate < 10$^{-8}$ M$_{\odot}$/yr for a sub-stellar mass of 15M$_{Jup}$. Finally, we report the first detection (> 3$\sigma$) of a ~ 20 au bar-like structure that crosses the gap through the central region of HD 100546. It is tentatively suggested that the bar could be dust dragged by infalling gas that radially flows from the outer disk. This could represent an exceptional case in which a small-scale radial inflow is observed in a single system. If this scenario is confirmed, it could explain the presence of atomic gas in the inner disk that would otherwise accrete on to the central star on a timescale of a few months/years, as previously indicated from spectro-interferometric data, and could be related with additional (undetected) planets.

Photonic technologies offer numerous advantages for astronomical instruments such as spectrographs and interferometers owing to their small footprints and diverse range of functionalities. Operating at the diffraction-limit, it is notoriously difficult to efficiently couple such devices directly with large telescopes. We demonstrate that with careful control of both the non-ideal pupil geometry of a telescope and residual wavefront errors, efficient coupling with single-mode devices can indeed be realised. A fibre injection was built within the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument. Light was coupled into a single-mode fibre operating in the near-IR (J-H bands) which was downstream of the extreme adaptive optics system and the pupil apodising optics. A coupling efficiency of 86% of the theoretical maximum limit was achieved at 1550 nm for a diffraction-limited beam in the laboratory, and was linearly correlated with Strehl ratio. The coupling efficiency was constant to within <30% in the range 1250-1600 nm. Preliminary on-sky data with a Strehl ratio of 60% in the H-band produced a coupling efficiency into a single-mode fibre of ~50%, consistent with expectations. The coupling was >40% for 84% of the time and >50% for 41% of the time. The laboratory results allow us to forecast that extreme adaptive optics levels of correction (Strehl ratio >90% in H-band) would allow coupling of >67% (of the order of coupling to multimode fibres currently). For Strehl ratios <20%, few-port photonic lanterns become a superior choice but the signal-to-noise must be considered. These results illustrate a clear path to efficient on-sky coupling into a single-mode fibre, which could be used to realise modal-noise-free radial velocity machines, very-long-baseline optical/near-IR interferometers and/or simply exploit photonic technologies in future instrument design.

We demonstrate for the first time an efficient, photonic-based astronomical spectrograph on the 8-m Subaru Telescope. An extreme adaptive optics system is combined with pupil apodiziation optics to efficiently inject light directly into a single-mode fiber, which feeds a compact cross-dispersed spectrograph based on array waveguide grating technology. The instrument currently offers a throughput of 5% from sky-to-detector which we outline could easily be upgraded to ~13% (assuming a coupling efficiency of 50%). The isolated spectrograph throughput from the single-mode fiber to detector was 42% at 1550 nm. The coupling efficiency into the single-mode fiber was limited by the achievable Strehl ratio on a given night. A coupling efficiency of 47% has been achieved with ~60% Strehl ratio on-sky to date. Improvements to the adaptive optics system will enable 90% Strehl ratio and a coupling of up to 67% eventually. This work demonstrates that the unique combination of advanced technologies enables the realization of a compact and highly efficient spectrograph, setting a precedent for future instrument design on very-large and extremely-large telescopes.

In an attempt to develop a streamlined astrophotonic instrument, we demonstrate the realization of an all-photonic device capable of both multimode to single mode conversion and spectral dispersion on an 8-m class telescope with efficient coupling. The device was a monolithic photonic spectrograph which combined an integrated photonic lantern, and an efficient arrayed waveguide grating device. During on-sky testing, we discovered a previously unreported type of noise that made spectral extraction and calibration extremely difficult. The source of the noise was traced to a wavelength-dependent loss mechanism between the feed fiber's multimode near-field pattern, and the modal acceptance profile of the integrated photonic lantern. Extensive modeling of the photonic components replicates the wavelength-dependent loss, and demonstrates an identical effect on the final spectral output. We outline that this could be mitigated by directly injecting into the integrated photonic lantern.

Imaging bundles provide a convenient way to translate a spatially coherent image, yet conventional imaging bundles made from silica fibre optics typically remain expensive with large losses due to poor filling factors (~40%). We present the characterisation of a novel polymer imaging bundle made from poly(methyl methacrylate) (PMMA) that is considerably cheaper and a better alternative to silica imaging bundles over short distances (~1 m; from the middle to the edge of a telescope's focal plane). The large increase in filling factor (92% for the polymer imaging bundle) outweighs the large increase in optical attenuation from using PMMA (1 dB/m) instead of silica (10^{-3} dB/m). We present and discuss current and possible future multi-object applications of the polymer imaging bundle in the context of astronomical instrumentation including: field acquisition, guiding, wavefront sensing, narrow-band imaging, aperture masking, and speckle imaging. The use of PMMA limits its use in low light applications (e.g. imaging of galaxies), however it is possible to fabricate polymer imaging bundles from a range of polymers that are better suited to the desired science.

The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument is a multipurpose high-contrast imaging platform designed for the discovery and detailed characterization of exoplanetary systems and serves as a testbed for high-contrast imaging technologies for ELTs. It is a multi-band instrument which makes use of light from 600 to 2500nm allowing for coronagraphic direct exoplanet imaging of the inner 3 lambda/D from the stellar host. Wavefront sensing and control are key to the operation of SCExAO. A partial correction of low-order modes is provided by Subaru's facility adaptive optics system with the final correction, including high-order modes, implemented downstream by a combination of a visible pyramid wavefront sensor and a 2000-element deformable mirror. The well corrected NIR (y-K bands) wavefronts can then be injected into any of the available coronagraphs, including but not limited to the phase induced amplitude apodization and the vector vortex coronagraphs, both of which offer an inner working angle as low as 1 lambda/D. Non-common path, low-order aberrations are sensed with a coronagraphic low-order wavefront sensor in the infrared (IR). Low noise, high frame rate, NIR detectors allow for active speckle nulling and coherent differential imaging, while the HAWAII 2RG detector in the HiCIAO imager and/or the CHARIS integral field spectrograph (from mid 2016) can take deeper exposures and/or perform angular, spectral and polarimetric differential imaging. Science in the visible is provided by two interferometric modules: VAMPIRES and FIRST, which enable sub-diffraction limited imaging in the visible region with polarimetric and spectroscopic capabilities respectively. We describe the instrument in detail and present preliminary results both on-sky and in the laboratory.

The circumstellar environment of L2 Pup, an oxygen-rich semiregular variable, was observed to understand the evolution of mass loss and the shaping of ejecta in the late stages of stellar evolution. High-angular resolution observations from a single 8 m telescope were obtained using aperture masking in the near-infrared (1.64, 2.30 and 3.74 $\rm\mu m$) on the NACO/VLT, both in imaging and polarimetric modes. The aperture-masking images of L2 Pup at 2.30 $\rm\mu m$ show a resolved structure that resembles a toroidal structure with a major axis of ~140 milliarcseconds (mas) and an east-west orientation. Two clumps can be seen on either side of the star, ~65 mas from the star, beyond the edge of the circumstellar envelope (estimated diameter is ~27 mas), while a faint, hook-like structure appear toward the northeast. The patterns are visible both in the imaging and polarimetric mode, although the latter was only used to measure the total intensity (Stokes I). The overall shape of the structure is similar at the 3.74 $\rm\mu m$ pseudo-continuum (dust emission), where the clumps appear to be embedded within a dark, dusty lane. The faint, hook-like patterns are also seen at this wavelength, extending northeast and southwest with the central, dark lane being an apparent axis of symmetry. We interpret the structure as a circumstellar torus with inner radius of 4.2 au. With a rotation velocity of 10 km s$^{-1}$ as suggested by the SiO maser profile, we estimate a stellar mass of 0.7 M$_\odot$.}

Direct imaging of protoplanetary disks promises to provide key insight into the complex sequence of processes by which planets are formed. However imaging the innermost region of such disks (a zone critical to planet formation) is challenging for traditional observational techniques (such as near-IR imaging and coronagraphy) due to the relatively long wavelengths involved and the area occulted by the coronagraphic mask. Here we introduce a new instrument -- VAMPIRES -- which combines non-redundant aperture-masking interferometry with differential polarimetry to directly image this previously inaccessible innermost region. By using the polarisation of light scattered by dust in the disk to provide precise differential calibration of interferometric visibilities and closure phases, VAMPIRES allows direct imaging at and beyond the telescope diffraction limit. Integrated into the SCExAO system at the Subaru telescope, VAMPIRES operates at visible wavelengths (where polarisation is high) while allowing simultaneous infrared observations conducted by HICIAO. Here we describe the instrumental design and unique observing technique and present the results of the first on-sky commissioning observations, validating the excellent visibility and closure phase precision which are then used to project expected science performance metrics.

Multiplicity is one of the most fundamental observable properties of massive O-type stars and offers a promising way to discriminate between massive star formation theories. Nevertheless, companions at separations between 1 and 100 mas remain mostly unknown due to intrinsic observational limitations. [...] The Southern MAssive Stars at High angular resolution survey (SMASH+) was designed to fill this gap by providing the first systematic interferometric survey of Galactic massive stars. We observed 117 O-type stars with VLTI/PIONIER and 162 O-type stars with NACO/SAM, respectively probing the separation ranges 1-45 and 30-250mas and brightness contrasts of Delta H < 4 and Delta H < 5. Taking advantage of NACO's field-of-view, we further uniformly searched for visual companions in an 8''-radius down to Delta H = 8. This paper describes the observations and data analysis, reports the discovery of almost 200 new companions in the separation range from 1mas to 8'' and presents the catalog of detections, including the first resolved measurements of over a dozen known long-period spectroscopic binaries. Excluding known runaway stars for which no companions are detected, 96 objects in our main sample (DEC < 0 deg; H<7.5) were observed both with PIONIER and NACO/SAM. The fraction of these stars with at least one resolved companion within 200mas is 0.53. Accounting for known but unresolved spectroscopic or eclipsing companions, the multiplicity fraction at separation < 8'' increases to f_m = 0.91 +/- 0.03. The fraction of luminosity class V stars that have a bound companion reaches 100% at 30mas while their average number of physically connected companions within 8'' is f_c = 2.2 +/- 0.3. This demonstrates that massive stars form nearly exclusively in multiple systems. Additionally, the nine non-thermal (NT) radio emitters observed by SMASH+ are all resolved [...]

The Gemini Planet Imager (GPI) Extreme Adaptive Optics Coronograph contains an interferometric mode: a 10-hole non-redundant mask (NRM) in its pupil wheel. GPI operates at $Y, J, H$, and $K$ bands, using an integral field unit spectrograph (IFS) to obtain spectral data at every image pixel. NRM on GPI is capable of imaging with a half resolution element inner working angle at moderate contrast, probing the region behind the coronagraphic spot. The fine features of the NRM PSF can provide a reliable check on the plate scale, while also acting as an attenuator for spectral standard calibrators that would otherwise saturate the full pupil. NRM commissioning data provides details about wavefront error in the optics as well as operations of adaptive optics control without pointing control from the calibration system. We compare lab and on-sky results to evaluate systematic instrument properties and examine the stability data in consecutive exposures. We discuss early on-sky performance, comparing images from integration and tests with the first on-sky images, and demonstrate resolving a known binary. We discuss the status of NRM and implications for future science with this mode.

The detection and characterisation of extra-solar planets is a major theme driving modern astronomy, with the vast majority of such measurements being achieved by Doppler radial-velocity and transit observations. Another technique -- direct imaging -- can access a parameter space that complements these methods, and paves the way for future technologies capable of detailed characterization of exoplanetary atmospheres and surfaces. However achieving the required levels of performance with direct imaging, particularly from ground-based telescopes which must contend with the Earth's turbulent atmosphere, requires considerable sophistication in the instrument and detection strategy. Here we demonstrate a new generation of photonic pupil-remapping devices which build upon the interferometric framework developed for the {\it Dragonfly} instrument: a high contrast waveguide-based device which recovers robust complex visibility observables. New generation Dragonfly devices overcome problems caused by interference from unguided light and low throughput, promising unprecedented on-sky performance. Closure phase measurement scatter of only $\sim 0.2^\circ$ has been achieved, with waveguide throughputs of $> 70\%$. This translates to a maximum contrast-ratio sensitivity (between the host star and its orbiting planet) at $1 \lambda/D$ (1$\sigma$ detection) of $5.3 \times 10^{-4}$ (when a conventional adaptive-optics (AO) system is used) or $1.8 \times 10^{-4}$ (for typical `extreme-AO' performance), improving even further when random error is minimised by averaging over multiple exposures. This is an order of magnitude beyond conventional pupil-segmenting interferometry techniques (such as aperture masking), allowing a previously inaccessible part of the star to planet contrast-separation parameter space to be explored.

In astronomy and microscopy, distortions in the wavefront affect the dynamic range of a high contrast imaging system. These aberrations are either imposed by a turbulent medium such as the atmosphere, by static or thermal aberrations in the optical path, or by imperfectly phased subapertures in a segmented mirror. Active and adaptive optics (AO), consisting of a wavefront sensor and a deformable mirror, are employed to address this problem. Nevertheless, the non-common-path between the wavefront sensor and the science camera leads to persistent quasi-static speckles that are difficult to calibrate and which impose a floor on the image contrast. In this paper we present the first experimental demonstration of a novel wavefront sensor requiring only a minor asymmetric obscuration of the pupil, using the science camera itself to detect high order wavefront errors from the speckle pattern produced. We apply this to correct errors imposed on a deformable microelectromechanical (MEMS) segmented mirror in a closed loop, restoring a high quality point spread function (PSF) and residual wavefront errors of order $\sim 10$ nm using 1600 nm light, from a starting point of $\sim 300$ nm in piston and $\sim 0.3$ mrad in tip-tilt. We recommend this as a method for measuring the non-common-path error in AO-equipped ground based telescopes, as well as as an approach to phasing difficult segmented mirrors such as on the \emph{James Webb Space Telescope} primary and as a future direction for extreme adaptive optics.

The Subaru Coronagraphic Extreme AO (SCExAO) instrument consists of a high performance Phase Induced Amplitude Apodisation (PIAA) coronagraph combined with an extreme Adaptive Optics (AO) system operating in the near-infrared (H band). The extreme AO system driven by the 2000 element deformable mirror will allow for Strehl ratios >90% to be achieved in the H-band when it goes closed loop. This makes the SCExAO instrument a powerful platform for high contrast imaging down to angular separations of the order of 1lambda/D and an ideal testbed for exploring coronagraphic techniques for ELTs. In this paper we report on the recent progress in regards to the development of the instrument, which includes the addition of a visible bench that makes use of the light at shorter wavelengths not currently utilized by SCExAO and closing the loop on the tip/tilt wavefront sensor. We will also discuss several exciting guest instruments which will expand the capabilities of SCExAO over the next few years; namely CHARIS which is a integral field spectrograph as well as VAMPIRES, a visible aperture masking experiment based on polarimetric analysis of circumstellar disks. In addition we will elucidate the unique role extreme AO systems will play in enabling high precision radial velocity spectroscopy for the detection of small companions.

We present the first multiplicity-dedicated long baseline optical interferometric survey of the Scorpius-Centaurus-Lupus-Crux association. We used the Sydney University Stellar Interferometer to undertake a survey for new companions to 58 Sco-Cen B- type stars and have detected 24 companions at separations ranging from 7-130mas, 14 of which are new detections. Furthermore, we use a Bayesian analysis and all available information in the literature to determine the multiplicity distribution of the 58 stars in our sample, showing that the companion frequency is F = 1.35 and the mass ratio distribution is best described as a power law with exponent equal to -0.46, agreeing with previous Sco-Cen high mass work and differing significantly from lower-mass stars in Tau-Aur. Based on our analysis, we estimate that among young B-type stars in moving groups, up to 23% are apparently single stars. This has strong implications for the understanding of high-mass star formation, which requires angular momentum dispersal through some mechanism such as formation of multiple systems.

In the two decades since the first extra-solar planet was discovered, the detection and characterization of extra-solar planets has become one of the key endeavors in all of modern science. Recently direct detection techniques such as interferometry or coronography have received growing attention because they reveal the population of exoplanets inaccessible to Doppler or transit techniques, and moreover they allow the faint signal from the planet itself to be investigated. Next-generation stellar interferometers are increasingly incorporating photonic technologies due to the increase in fidelity of the data generated. Here, we report the design, construction and commissioning of a new high contrast imager; the integrated pupil-remapping interferometer; an instrument we expect will find application in the detection of young faint companions in the nearest star-forming regions. The laboratory characterisation of the instrument demonstrated high visibility fringes on all interferometer baselines in addition to stable closure phase signals. We also report the first successful on-sky experiments with the prototype instrument at the 3.9-m Anglo-Australian Telescope. Performance metrics recovered were consistent with ideal device behaviour after accounting for expected levels of decoherence and signal loss from the uncompensated seeing. The prospect of complete Fourier-coverage coupled with the current performance metrics means that this photonically-enhanced instrument is well positioned to contribute to the science of high contrast companions.

A method for designing physically path length matched, three-dimensional photonic circuits is described. We focus specifically on the case where all the waveguides are uniquely routed from the input to output; a problem which has not been addressed to date and allows for the waveguides to be used in interferometric measurements. Circuit elements were fabricated via the femtosecond laser direct-write technique. We demonstrate via interferometric methods that the fabricated circuits were indeed optically path length matched to within 45 um which is within the coherence length required for many applications.

Intermediate-mass stars end their lives by ejecting the bulk of their envelope via a slow dense wind back into the interstellar medium, to form the next generation of stars and planets. Stellar pulsations are thought to elevate gas to an altitude cool enough for the condensation of dust, which is then accelerated by radiation pressure from starlight, entraining the gas and driving the wind. However accounting for the mass loss has been a problem due to the difficulty in observing tenuous gas and dust tens of milliarcseconds from the star, and there is accordingly no consensus on the way sufficient momentum is transferred from the starlight to the outflow. Here, we present spatially-resolved, multi-wavelength observations of circumstellar dust shells of three stars on the asymptotic giant branch of the HR diagram. When imaged in scattered light, dust shells were found at remarkably small radii (<~ 2 stellar radii) and with unexpectedly large grains (~300 nm radius). This proximity to the photosphere argues for dust species that are transparent to starlight and therefore resistant to sublimation by the intense radiation field. While transparency usually implies insufficient radiative pressure to drive a wind, the radiation field can accelerate these large grains via photon scattering rather than absorption - a plausible mass-loss mechanism for lower-amplitude pulsating stars.

The new operational mode of aperture masking interferometry has been added to the CONICA camera which lies downstream of the Adaptive Optics (AO) corrected focus provided by NAOS on the VLT-UT4 telescope. Masking has been shown to deliver superior PSF calibration, rejection of atmospheric noise and robust recovery of phase information through the use of closure phases. Over the resolution range from about half to several resolution elements, masking interferometry is presently unsurpassed in delivering high fidelity imaging and direct detection of faint companions. Here we present results from commissioning data using this powerful new operational mode, and discuss the utility for masking in a variety of scientific contexts. Of particular interest is the combination of the CONICA polarimetry capabilities together with SAM mode operation, which has revealed structures never seen before in the immediate circumstellar environments of dusty evolved stars.