Interpixel capacitance (IPC) between adjacent pixels in hybridized arrays gives rise to an electrostatic cross talk. This cross talk causes MTF degradation and blurring of images or spectra collected using these devices. As pixel size is driven down from the 18 micron pixel pitch of the H2RG read out circuits to the 10 or 15 micron H4RGs IPC is driven up resulting in greater cross talk, all else being equal. Mounting evidence indicates that IPC varies as a function of depletion state of the photo-active diodes. For single pixel events, increasing the event intensity corresponds to a decreasing fractional coupling. If left uncorrected, IPC can give rise to systematic errors in precision astrometric and photometric measurements, in particular when dealing with confused point sources or spatially extended structures for shape measurements as demonstrated through comparison of registered sources from ESO HAWK-I and HST ACS WFC datasets. Furthermore these errors will be the most significant when operating near the sensitivity limit of these devices. Deconvolution based correction methods are invalidated by this same signal dependence. Instead a numerical method of successive approximation can be used to correct coupling due to a well characterized IPC. Examination of single pixel reset data above flat fields could be used to characterize IPC's functional relationship for neighboring pixels. This higher quality characterization can result in more accurate correction.

In the last decade, imaging polarimeters based on micropolarizer arrays have been developed for use in terrestrial remote sensing and metrology applications. Micropolarizer-based sensors are dramatically smaller and more mechanically robust than other polarimeters with similar spectral response and snapshot capability. To determine the suitability of these new polarimeters for astronomical applications, we developed the RIT Polarization Imaging Camera to investigate the performance of these devices, with a special attention to the low signal-to-noise regime. We characterized the device performance in the lab, by determining the relative throughput, efficiency, and orientation of every pixel, as a function of wavelength. Using the resulting pixel response model, we developed demodulation procedures for aperture photometry and imaging polarimetry observing modes. We found that, using the current calibration, RITPIC is capable of detecting polarization signals as small as <0.3%. To demonstrate the stability of RITPIC's calibration and its extreme portability, we performed imaging polarimetry of the Solar corona in Madras, Oregon during the total Solar eclipse of 2017. The maximum polarization we measured was ~46%, which agrees well with the maximum value predicted for a Thomson scattering corona. Similarly, we found no strong deviations in the angle of linear polarization from the tangential direction. The relative ease of data collection, calibration, and analysis provided by these sensors suggest than they may become an important tool for a number of astronomical targets.

Space missions designed for high precision photometric monitoring of stars often under-sample the point-spread function, with much of the light landing within a single pixel. Missions like MOST, Kepler, BRITE, and TESS, do this to avoid uncertainties due to pixel-to-pixel response nonuniformity. This approach has worked remarkably well. However, individual pixels also exhibit response nonuniformity. Typically, pixels are most sensitive near their centers and less sensitive near the edges, with a difference in response of as much as 50%. The exact shape of this fall-off, and its dependence on the wavelength of light, is the intra-pixel response function (IPRF). A direct measurement of the IPRF can be used to improve the photometric uncertainties, leading to improved photometry and astrometry of under-sampled systems. Using the spot-scan technique, we measured the IPRF of a flight spare e2v CCD90 imaging sensor, which is used in the Kepler focal plane. Our spot scanner generates spots with a full-width at half-maximum of $\lesssim$3 microns across the range of 400 nm - 850 nm. We find that Kepler's CCD shows similar IPRF behavior to other back-illuminated devices, with a decrease in responsivity near the edges of a pixel by $\sim$50%. The IPRF also depends on wavelength, exhibiting a large amount of diffusion at shorter wavelengths and becoming much more defined by the gate structure in the near-IR. This method can also be used to measure the IPRF of the CCDs used for TESS, which borrows much from the Kepler mission.

ATLAS (Astrophysics Telescope for Large Area Spectroscopy) is a concept for a NASA probe-class space mission. It is the spectroscopic follow-up mission to WFIRST, boosting its scientific return by obtaining deep NIR & MIR slit spectroscopy for most of the galaxies imaged by the WFIRST High Latitude Survey at z>0.5. ATLAS will measure accurate and precise redshifts for ~200M galaxies out to z=7 and beyond, and deliver spectra that enable a wide range of diagnostic studies of the physical properties of galaxies over most of cosmic history. ATLAS and WFIRST together will produce a definitive 3D map of the Universe over 2000 sq deg. ATLAS Science Goals are: (1) Discover how galaxies have evolved in the cosmic web of dark matter from cosmic dawn through the peak era of galaxy assembly. (2) Discover the nature of cosmic acceleration. (3) Probe the Milky Way's dust-enshrouded regions, reaching the far side of our Galaxy. (4) Discover the bulk compositional building blocks of planetesimals formed in the outer Solar System. These flow down to the ATLAS Scientific Objectives: (1A) Trace the relation between galaxies and dark matter with less than 10% shot noise on relevant scales at 1<z<7. (1B) Probe the physics of galaxy evolution at 1<z<7. (2) Obtain definitive measurements of dark energy and tests of General Relativity. (3) Measure the 3D structure and stellar content of the inner Milky Way to a distance of 25 kpc. (4) Detect and quantify the composition of 3,000 planetesimals in the outer Solar System. ATLAS is a 1.5m telescope with a FoV of 0.4 sq deg, and uses Digital Micro-mirror Devices (DMDs) as slit selectors. It has a spectroscopic resolution of R = 1000, and a wavelength range of 1-4 microns. ATLAS has an unprecedented spectroscopic capability based on DMDs, with a spectroscopic multiplex factor ~6,000. ATLAS is designed to fit within the NASA probe-class space mission cost envelope.

ATLAS (Astrophysics Telescope for Large Area Spectroscopy) Probe is a concept for a NASA probe-class space mission. It is the follow-up space mission to WFIRST, boosting its scientific return by obtaining deep IR slit spectroscopy for 70% of all galaxies imaged by a 2000 sq deg WFIRST High Latitude Survey at z>0.5. ATLAS will measure accurate and precise redshifts for 200M galaxies out to z < 7, and deliver spectra that enable a wide range of diagnostic studies of the physical properties of galaxies over most of cosmic history. ATLAS Probe science spans four broad categories: (1) Revolutionizing galaxy evolution studies by tracing the relation between galaxies and dark matter from galaxy groups to cosmic voids and filaments, from the epoch of reionization through the peak era of galaxy assembly; (2) Opening a new window into the dark Universe by weighing the dark matter filaments using 3D weak lensing with spectroscopic redshifts, and obtaining definitive measurements of dark energy and modification of General Relativity using galaxy clustering; (3) Probing the Milky Way's dust-enshrouded regions, reaching the far side of our Galaxy; and (4) Exploring the formation history of the outer Solar System by characterizing Kuiper Belt Objects. ATLAS Probe is a 1.5m telescope with a field of view of 0.4 sq deg, and uses Digital Micro-mirror Devices (DMDs) as slit selectors. It has a spectroscopic resolution of R = 1000 over 1-4 microns, and a spectroscopic multiplex factor >5,000. ATLAS is designed to fit within the NASA probe-class space mission cost envelope; it has a single instrument, a telescope aperture that allows for a lighter launch vehicle, and mature technology. ATLAS Probe will lead to transformative science over the entire range of astrophysics: from galaxy evolution to the dark Universe, from Solar System objects to the dusty regions of the Milky Way.

Space missions designed for high precision photometric monitoring of stars often under-sample the point-spread function, with much of the light landing within a single pixel. Missions like MOST, Kepler, BRITE, and TESS, do this to avoid uncertainties due to pixel-to-pixel response nonuniformity. This approach has worked remarkably well. However, individual pixels also exhibit response nonuniformity. Typically, pixels are most sensitive near their centers and less sensitive near the edges, with a difference in response of as much as 50%. The exact shape of this fall-off, and its dependence on the wavelength of light, is the intra-pixel response function (IPRF). A direct measurement of the IPRF can be used to improve the photometric uncertainties, leading to improved photometry and astrometry of under-sampled systems. Using the spot-scan technique, we measured the IPRF of a flight spare e2v CCD90 imaging sensor, which is used in the Kepler focal plane. Our spot scanner generates spots with a full-width at half-maximum of $\lesssim$5 microns across the range of 400 nm - 900 nm. We find that Kepler's CCD shows similar IPRF behavior to other back-illuminated devices, with a decrease in responsivity near the edges of a pixel by $\sim$50%. The IPRF also depends on wavelength, exhibiting a large amount of diffusion at shorter wavelengths and becoming much more defined by the gate structure in the near-IR. This method can also be used to measure the IPRF of the CCDs used for TESS, which borrows much from the Kepler mission.

Interpixel capacitance (IPC) is a deterministic electronic coupling that results in a portion of the collected signal incident on one pixel of a hybridized detector array being measured in adjacent pixels. Data collected by light sensitive HgCdTe arrays which exhibit this coupling typically goes uncorrected or is corrected by treating the coupling as a fixed point spread function. Evidence suggests that this IPC coupling is not uniform across different signal and background levels. This variation invalidates assumptions that are key in decoupling techniques such as Wiener Filtering or application of the Lucy- Richardson algorithm. Additionally, the variable IPC results in the point spread function (PSF) depending upon a star's signal level relative to the background level, amond other parameters. With an IPC ranging from 0.68% to 1.45% over the full well depth of a sensor, as is a reasonable range for the H2RG arrays, the FWHM of the JWSTs NIRCam 405N band is degraded from 2.080 pix (0".132) as expected from the diffraction patter to 2.186 pix (0".142) when the star is just breaching the sensitivity limit of the system. For example, when attempting to use a fixed PSF fitting (e.g. assuming the PSF observed from a bright star in the field) to untangle two sources with a flux ratio of 4:1 and a center to center distance of 3 pixels, flux estimation can be off by upwards of 1.5% with a separation error of 50 millipixels. To deal with this issue an iterative non-stationary method for deconvolution is here proposed, implemented, and evaluated that can account for the signal dependent nature of IPC.

In the last decade, imaging polarimeters based on micropolarizer arrays have been developed for use in terrestrial remote sensing and metrology applications. Micropolarizer-based sensors are dramatically smaller and more mechanically robust than other polarimeters with similar spectral response and snapshot capability. To determine the suitability of these new polarimeters for astronomical applications, we developed the RIT Polarization Imaging Camera to investigate the performance of these devices, with a special attention to the low signal-to-noise regime. We characterized the device performance in the lab, by determining the relative throughput, efficiency, and orientation of every pixel, as a function of wavelength. Using the resulting pixel response model, we developed demodulation procedures for aperture photometry and imaging polarimetry observing modes. We found that, using the current calibration, RITPIC is capable of detecting polarization signals as small as $\sim0.3\%$. The relative ease of data collection, calibration, and analysis provided by these sensors suggest than they may become an important tool for a number of astronomical targets.

The astronomical community continues to be interested in suitable programmable slit masks for use in multi-object spectrometers (MOSs) on space missions. There have been ground-based MOS utilizing digital micromirror devices (DMDs) and they have proven to be highly accurate and reliable instruments. This paper summarizes the results of a continuing study to investigate the performance of DMDs under conditions associated with space deployment. This includes the response of DMDs to radiation, to the vibration and mechanical shock loads associated with launch, and the operability of DMD under cryogenic temperatures. The optical contrast ratio and a study of the long-term reflectance of a bare device have also been investigated. The results of the radiation testing demonstrate that DMDs in orbit would experience negligible heavy-ion induced single event upset (SEU) rate burden, we predict SEU rate of 5.6 micromirrors per 24 hours. Vibration and mechanical shock testing was performed according to the NASA General Environmental Verification Standard (GEVS), no mirrors failed in the devices tested. The results of low temperature testing suggest that DMDs are not affected by the thermal load and operate smoothly at temperatures at least as low as 78 K. The reflectivity of a bare DMD did not measurably change even after being exposed to ambient conditions over a period of 13 months. The measured contrast ratio (on state vs off state of the DMD micromirrors) was greater than 6000/:1 when illuminated with an f/4 optical beam. Overall, DMDs are extremely robust and promise to provide a reliable alternative to micro shutter arrays (MSA) to be used in space as remotely programmable slit masks for MOS design.

Inter pixel capacitance (IPC) is a deterministic electronic coupling resulting in a portion of signal incident on one pixel of a hybridized detector array being measured in adjacent pixels. Data collected by light sensitive HgCdTe arrays which exhibit this coupling typically goes uncorrected or is corrected by treating the coupling as a fixed point spread function. Evidence suggests that this coupling is not uniform across signal and background levels. Sub-arrays of pixels using design parameters based upon HgCdTe indium hybridized arrays akin to those contained in the James Webb Space Telescope's NIRcam have been modeled from first principles using Lumerical DEVICE software. This software simultaneously solves Poisson's Equation and the Drift Diffusion Equations yielding charge distributions and electric fields. Modeling of this sort generates the local point spread function across a range of detector parameters. This results in predictive characterization of IPC across scene and device parameters that would permit proper photometric correction and signal restoration to the data. Additionally, the ability to visualize potential distributions and couplings as generated by the models yields insight that can be used to minimize IPC coupling in the design of future detectors.

The next fundamental steps forward in understanding our place in the universe could be a result of advances in extreme contrast ratio (ECR) imaging and point spread function (PSF) suppression. For example, blinded by quasar light we have yet to fully understand the processes of galaxy formation and evolution, and there is an ongoing race to obtain a direct image of an exoearth lost in the glare of its host star. To fully explore the features of these systems we must perform observations in which contrast ratios of at least one billion can be regularly achieved with sub 0.1" inner working angles. Here we present the details of a latest generation 32-bit charge injection device (CID) that could conceivably achieve contrast ratios on the order of one billion. We also demonstrate some of its ECR imaging abilities for astronomical imaging. At a separation of two arc minutes, we report a direct contrast ratio of Delta(m_v)=18.3, log(CR)=7.3, or 1 part in 20 million, from observations of the Sirius field. The atmospheric conditions present during the collection of this data prevented less modest results, and we expect to be able to achieve higher contrast ratios, with improved inner working angles, simply by operating a CID at a world-class observing site. However, CIDs do not directly provide any PSF suppression. Therefore, combining CID imaging with a simple PSF suppression technique like angular differential imaging, could provide a cheap and easy alternative to the complex ECR techniques currently being employed.

A lightcurve of the eclipsing binary CM Draconis has been analyzed for the presence of transits of planets of size >= 2.5 Earth-radii (Re), with periods of 60 days or less, and in co-planar orbits around the binary system. About 400 million model lightcurves, representing transits from planets with periods ranging from 7 to 60 days, have been matched/correlated against these data. This process we call the "transit detection algorithm" or TDA. The resulting `transit-statistics' for each planet candidate allow the quantification of detection probabilities, and of false alarm rates. Our current lightcurve of CM Dra has a coverage of 1014 hours with 26,043 individual points, at a photometric precision between 0.2% and 0.7%. Planets significantly larger then 3Re would constitute a `supra-noise' detection, and for periods of 60 days or less, they would have been detected with a probability of 90%. `Subnoise' detections of smaller planets are more constrained. For example, 2.5 Re planets with 10-day periods or less would have been detected with an 80% probability. The necessity for predicted observations is illustrated with the nine top planet candidates that emerged from our TDA analysis. They are the planet candidates with the highest transit-statistics from the 1994-1998 observing seasons and, for them, transits for the 1999 observing season were predicted. Of the seven candidates that were then observationally tested in 1999, all were ruled out except one, which needs further observational confirmation. We conclude that the photometric transit method is a viable way to search for relatively small, inner extrasolar planets with moderate-sized telescopes using CCD photometry with a matching-filter analysis.

Results from a photometric search for extrasolar planetary transits across the eclipsing binary CM Dra are presented. The TEP (Transits of Extrasolar Planets) network has observed this star since 1994, and a lightcurve with 617 hours of coverage has been obtained. The data give a complete phase coverage of the CM Dra system at each of the 3 years of observations, with a noise of less than 5 mmag. New epoch and period values for CM Dra are derived, and a low flare rate of 0.025/hr has been confirmed. The absence of periodic variations in eclipse minimum times excludes the presence of very massive planets with periods of less than a few years. The lightcurve was visually scanned for the presence of unusual events which may be indicative of transits of extrasolar planets with 'massive earth' sizes. Six suspicious events were found which are being followed up for future transits, by planets with sizes between 1.5 and 2.5 RE (Earth Radii). However, none of these events has amplitudes compatible with planets larger than 2.5 RE. Coplanar planets larger than 2.5 RE and with orbital periods of less than 60 days can therefore be ruled out with a confidence of about 80%. Planets smaller than 1.5 RE cannot be detected in the data without a sub-noise detection algorithm. A preliminary signal detection analysis shows that there is a 50% detection confidence for 2 RE planets with a period from 10 to 30 days with the current data. This data-set demonstrates that it is possible to detect terrestrial sized planets with ground based photometry, and that strong constraints on the sizes of planets orbiting in the plane of the CM Dra system can be set.