Studying the atmospheric Planetary Boundary Layer (PBL) is crucial to understand the climate of a planet. The meteorological measurements by the instruments onboard InSight make a uniquely rich dataset to study the active turbulent dynamics of the daytime PBL on Mars. Here we use the high-sensitivity continuous pressure, wind, temperature measurements in the first 400 sols of InSight operations to analyze convective gusts, cells, and vortices in Mars' daytime PBL. We compare the InSight measurements to turbulence-resolving Large-Eddy Simulations (LES). The daytime PBL turbulence at the InSight landing site is found to be very active, with clearly identified signatures of convective cells and a vast population of almost 10,000 recorded vortex encounters, adequately represented by a power-law with a 3.5 exponent in agreement with LES results. While the daily variability of vortex encounters at the InSight landing site can be explained by the statistical nature of turbulence, the seasonal variability is strongly correlated with ambient wind speed, which is supported by LES. However, wind gustiness is more correlated to surface temperature than ambient wind speed, confirming the radiative control of the daytime martian PBL; and fewer convective vortices are forming in LES when the background wind is doubled. Thus, the long-term seasonal variability of vortex encounters at the InSight landing site is mainly controlled by the advection of convective vortices by the ambient wind speed. Typical tracks followed by vortices forming in the LES show a similar distribution in direction and length as orbital imagery of the InSight region.

Before deploying to the surface of Mars, the short-period (SP) seismometer of the InSight mission operated on deck for a total of 48 hours. This dataset can be used to understand how deck-mounted seismometers can be used in future landed missions to Mars, Europa, and other planetary bodies. While operating on deck, the SP seismometer showed signals comparable to the Viking-2 seismometer near 3 Hz where the sensitivity of the Viking instrument peaked. Wind sensitivity showed similar patterns to the Viking instrument, although amplitudes on InSight were ~80% larger for a given wind velocity. However, during the low wind evening hours the instrument noise levels at frequencies between 0.1 and 1 Hz were comparable to quiet stations on Earth, although deployment to the surface below the Wind and Thermal Shield lowered installation noise by roughly 40 dB in acceleration power. With the observed noise levels and estimated seismicity rates for Mars, detection probability for quakes for a deck-mounted instrument are low enough that up to years of on-deck recordings may be necessary to observe an event. Because the noise is dominated by wind acting on the lander, though, deck-mounted seismometers may be more practical for deployment on airless bodies, and it is important to evaluate the seismicity of the target body and the specific design of the lander. Detection probabilities for operation on Europa reach over 99% for some proposed seismicity models for a similar duration of operation if noise levels are comparable to low-wind time periods on Mars.

Asteroids and other Small Solar System Bodies (SSSBs) are of high general and scientific interest in many aspects. The origin, formation, and evolution of our Solar System (and other planetary systems) can be better understood by analysing the constitution and physical properties of small bodies in the Solar System. Currently, two space missions (Hayabusa2, OSIRIS-REx) have recently arrived at their respective targets and will bring a sample of the asteroids back to Earth. Other small body missions have also been selected by, or proposed to, space agencies. The threat posed to our planet by near-Earth objects (NEOs) is also considered at the international level, and this has prompted dedicated research on possible mitigation techniques. The DART mission, for example, will test the kinetic impact technique. Even ideas for industrial exploitation have risen during the last years. Lastly, the origin of water and life on Earth appears to be connected to asteroids. Hence, future space mission projects will undoubtedly target some asteroids or other SSSBs. In all these cases and research topics, specific knowledge of the structure and mechanical behaviour of the surface as well as the bulk of those celestial bodies is crucial. In contrast to large telluric planets and dwarf planets, a large proportion of such small bodies is believed to consist of gravitational aggregates ('rubble piles') with no -- or low -- internal cohesion, with varying macro-porosity and surface properties (from smooth regolith covered terrain, to very rough collection of boulders), and varying topography (craters, depressions, ridges) [...].

CASTAway is a mission concept to explore our Solar System's main asteroid belt. Asteroids and comets provide a window into the formation and evolution of our Solar System and the composition of these objects can be inferred from space-based remote sensing using spectroscopic techniques. Variations in composition across the asteroid populations provide a tracer for the dynamical evolution of the Solar System. The mission combines a long-range (point source) telescopic survey of over 10,000 objects, targeted close encounters with 10 to 20 asteroids and serendipitous searches to constrain the distribution of smaller (e.g. 10 m) size objects into a single concept. With a carefully targeted trajectory that loops through the asteroid belt, CASTAway would provide a comprehensive survey of the main belt at multiple scales. The scientific payload comprises a 50 cm diameter telescope that includes an integrated low-resolution (R = 30 to 100) spectrometer and visible context imager, a thermal (e.g. 6 to 16 microns) imager for use during the flybys, and modified star tracker cameras to detect small (approx. 10 m) asteroids. The CASTAway spacecraft and payload have high levels of technology readiness and are designed to fit within the programmatic and cost caps for a European Space Agency medium class mission, whilst delivering a significant increase in knowledge of our Solar System.

The atmospheric pressure fluctuations on Mars induce an elastic response in the ground that creates a ground tilt, detectable as a seismic signal on the InSight seismometer SEIS. The seismic pressure noise is modeled using Large Eddy Simulations of the wind and surface pressure at the InSight landing site and a Green's function ground deformation approach that is subsequently validated via a detailed comparison with two other methods based on Sorrells' theory (Sorrels 1971; Sorrels et al. 1971). The horizontal acceleration as a result of the ground tilt due to the LES turbulence-induced pressure fluctuations are found to be typically ~2 - 40 nm/s^2 in amplitude, whereas the direct horizontal acceleration is two orders of magnitude smaller and is thus negligible in comparison. The vertical accelerations are found to be ~0.1 - 6 nm/s^2 in amplitude. We show that under calm conditions, a single-pressure measurement is representative of the large-scale pressure field (to a distance of several kilometers), particularly in the prevailing wind direction. However, during windy conditions, small-scale turbulence results in a reduced correlation between the pressure signals, and the single-pressure measurement becomes less representative of the pressure field. Nonetheless, the correlation between the seismic signal and the pressure signal is found to be higher for the windiest period because the seismic pressure noise reflects the atmospheric structure close to the seismometer. In the same way that we reduce the atmospheric seismic signal by making use of a pressure sensor that is part of the InSight APSS (Auxiliary Payload Sensor Suite), we also the use the synthetic noise data obtained from the LES pressure field to demonstrate a decorrelation strategy.

In order to improve our understanding of landing on small bodies and of asteroid evolution, we use our novel drop tower facility to perform low-velocity (2-40 cm s^-1), shallow impact experiments of a 10 cm diameter aluminum sphere into quartz sand in low effective gravities (~0.2-1 m s^-2). Using in situ accelerometers, we measure the acceleration profile during the impacts and determine the peak accelerations, collision durations and maximum penetration depth. We find that the penetration depth scales linearly with the collision velocity but is independent of the effective gravity for the experimental range tested, and that the collision duration is independent of both the effective gravity and the collision velocity. No rebounds are observed in any of the experiments. Our low-gravity experimental results indicate that the transition from the quasi-static regime to the inertial regime occurs for impact energies two orders of magnitude smaller than in similar impact experiments under terrestrial gravity. The lower energy regime change may be due to the increased hydrodynamic drag of the surface material in our experiments, but may also support the notion that the quasi-static regime reduces as the effective gravity becomes lower.

The aim of the Asteroid Science Intersections with In-Space Mine Engineering (ASIME) 2016 conference on September 21-22, 2016 in Luxembourg City was to provide an environment for the detailed discussion of the specific properties of asteroids, with the engineering needs of space missions that utilize asteroids. The ASIME 2016 Conference produced a layered record of discussions from the asteroid scientists and the asteroid miners to understand each other's key concerns and to address key scientific questions from the asteroid mining companies: Planetary Resources, Deep Space Industries and TransAstra. These Questions were the focus of the two day conference, were addressed by scientists inside and outside of the ASIME Conference and are the focus of this White Paper. The Questions from the asteroid mining companies have been sorted into the three asteroid science themes: 1) survey, 2) surface and 3) subsurface and 4) Other. The answers to those Questions have been provided by the scientists with their conference presentations or edited directly into an early open-access collaborative Google document (August 2016-October 2016), or inserted by A. Graps using additional reference materials. During the ASIME 2016 last two-hours, the scientists turned the Questions from the Asteroid Miners around by presenting their own key concerns: Questions from the Asteroid Scientists . These answers in this White Paper will point to the Science Knowledge Gaps (SKGs) for advancing the asteroid in-space resource utilisation domain.

The SEIS (Seismic Experiment for Interior Structures) instrument onboard the InSight mission to Mars is the critical instrument for determining the interior structure of Mars, the current level of tectonic activity and the meteorite flux. Meeting the performance requirements of the SEIS instrument is vital to successfully achieve these mission objectives. Here we analyse in-situ wind measurements from previous Mars space missions to understand the wind environment that we are likely to encounter on Mars, and then we use an elastic ground deformation model to evaluate the mechanical noise contributions on the SEIS instrument due to the interaction between the Martian winds and the InSight lander. Lander mechanical noise maps that will be used to select the best deployment site for SEIS once the InSight lander arrives on Mars are also presented. We find the lander mechanical noise may be a detectable signal on the InSight seismometers. However, for the baseline SEIS deployment position, the noise is expected to be below the total noise requirement >97% of the time and is, therefore, not expected to endanger the InSight mission objectives.

This work presents an experimental design for studying low-velocity collisions into granular surfaces in low-gravity. In the experiment apparatus, reduced-gravity is simulated by releasing a free-falling projectile into a surface container with a downward acceleration less than that of Earth's gravity. The acceleration of the surface is controlled through the use of an Atwood machine, or a system of pulleys and counterweights. The starting height of the surface container and the initial separation distance between the projectile and surface are variable and chosen to accommodate collision velocities up to 20 cm/s and effective accelerations of ~0.1 - 1.0 m/s^2. Accelerometers, placed on the surface container and inside the projectile, provide acceleration data, while high-speed cameras capture the collision and act as secondary data sources. The experiment is built into an existing 5.5 m drop-tower frame and requires the custom design of all components, including the projectile, surface sample container, release mechanism and deceleration system. Data from calibration tests verify the efficiency of the experiment's deceleration system and provide a quantitative understanding of the performance of the Atwood system.

We report seismic signals on a desert playa caused by convective vortices and dust devils. The long-period (10-100s) signatures, with tilts of ~10$^{-7}$ radians, are correlated with the presence of vortices, detected with nearby sensors as sharp temporary pressure drops (0.2-1 mbar) and solar obscuration by dust. We show that the shape and amplitude of the signals, manifesting primarily as horizontal accelerations, can be modeled approximately with a simple quasi-static point-load model of the negative pressure field associated with the vortices acting on the ground as an elastic half space. We suggest the load imposed by a dust devil of diameter D and core pressure {\Delta}Po is ~({\pi}/2){\Delta}PoD$^2$, or for a typical terrestrial devil of 5 m diameter and 2 mbar, about the weight of a small car. The tilt depends on the inverse square of distance, and on the elastic properties of the ground, and the large signals we observe are in part due to the relatively soft playa sediment and the shallow installation of the instrument. Ground tilt may be a particularly sensitive means of detecting dust devils. The simple point-load model fails for large dust devils at short ranges, but more elaborate models incorporating the work of Sorrells (1971) may explain some of the more complex features in such cases, taking the vortex winds and ground velocity into account. We discuss some implications for the InSight mission to Mars.

The regolith-covered surfaces of asteroids preserve records of geophysical processes that have occurred both at their surfaces and sometimes also in their interiors. As a result of the unique micro-gravity environment that these bodies posses, a complex and varied geophysics has given birth to fascinating features that we are just now beginning to understand. The processes that formed such features were first hypothesised through detailed spacecraft observations and have been further studied using theoretical, numerical and experimental methods that often combine several scientific disciplines. These multiple approaches are now merging towards a further understanding of the geophysical states of the surfaces of asteroids. In this chapter we provide a concise summary of what the scientific community has learned so far about the surfaces of these small planetary bodies and the processes that have shaped them. We also discuss the state of the art in terms of experimental techniques and numerical simulations that are currently being used to investigate regolith processes occurring on small-body surfaces and that are contributing to the interpretation of observations and the design of future space missions.

Seismic shaking is an attractive mechanism to explain the destabilisation of regolith slopes and the regolith migration found on the surfaces of asteroids (Richardson et al. 2004; Miyamoto et al. 2007). Here, we use a continuum mechanics method to simulate the seismic wave propagation in an asteroid. Assuming that asteroids can be described by a cohesive core surrounded by a thin non-cohesive regolith layer, our numerical simulations of vibrations induced by micro-meteoroids suggest that the surface peak ground accelerations induced by micro-meteoroid impacts may have been previously under-estimated. Our lower bound estimate of vertical accelerations induced by seismic waves is about 50 times larger than previous estimates. It suggests that impact events triggering seismic activity are more frequent than previously assumed for asteroids in the kilometric and sub-kilometric size range. The regolith lofting is also estimated by a first order ballistic approximation. Vertical displacements are small, but lofting times are long compared to the duration of the seismic signals. The regolith movement has a non-linear dependence on the distance to the impact source which is induced by the type of seismic wave generating the first movement. The implications of regolith concentration in lows of surface acceleration potential are also discussed. We suggest that the resulting surface thermal inertia variations of small fast rotators may induce an increased sensitivity of these objects to the Yarkovsky effect.

We present a new particle-based (discrete element) numerical method for the simulation of granular dynamics, with application to motions of particles on small solar system body and planetary surfaces. The method employs the parallel N-body tree code pkdgrav to search for collisions and compute particle trajectories. Collisions are treated as instantaneous point-contact events between rigid spheres. Particle confinement is achieved by combining arbitrary combinations of four provided wall primitives, namely infinite plane, finite disk, infinite cylinder, and finite cylinder, and degenerate cases of these. Various wall movements, including translation, oscillation, and rotation, are supported. We provide full derivations of collision prediction and resolution equations for all geometries and motions. Several tests of the method are described, including a model granular "atmosphere" that achieves correct energy equipartition, and a series of tumbler simulations that show the expected transition from tumbling to centrifuging as a function of rotation rate.

Surfaces of planets and small bodies of our Solar System are often covered by a layer of granular material that can range from a fine regolith to a gravel-like structure of varying depths. Therefore, the dynamics of granular materials are involved in many events occurring during planetary and small-body evolution thus contributing to their geological properties. We demonstrate that the new adaptation of the parallel N-body hard-sphere code pkdgrav has the capability to model accurately the key features of the collective motion of bidisperse granular materials in a dense regime as a result of shaking. As a stringent test of the numerical code we investigate the complex collective ordering and motion of granular material by direct comparison with laboratory experiments. We demonstrate that, as experimentally observed, the scale of the collective motion increases with increasing small-particle additive concentration. We then extend our investigations to assess how self-gravity and external gravity affect collective motion. In our reduced-gravity simulations both the gravitational conditions and the frequency of the vibrations roughly match the conditions on asteroids subjected to seismic shaking, though real regolith is likely to be much more heterogeneous and less ordered than in our idealised simulations. We also show that collective motion can occur in a granular material under a wide range of inter-particle gravity conditions and in the absence of an external gravitational field. These investigations demonstrate the great interest of being able to simulate conditions that are to relevant planetary science yet unreachable by Earth-based laboratory experiments.

Despite their very low surface gravities, asteroids exhibit a number of different geological processes involving granular matter. Understanding the response of this granular material subject to external forces in microgravity conditions is vital to the design of a successful asteroid sub-surface sampling mechanism, and in the interpretation of the fascinating geology on an asteroid. We have designed and flown a Taylor-Couette shear cell to investigate granular flow due to rotational shear forces under the conditions of parabolic flight microgravity. The experiments occur under weak compression. First, we present the technical details of the experimental design with particular emphasis on how the equipment has been specifically designed for the parabolic flight environment. Then, we investigate how a steady state granular flow induced by rotational shear forces differs in varying gravitational environments. We find that the effect of constant shearing on the granular material, in a direction perpendicular to the effective acceleration, does not seem to be strongly influenced by gravity. This means that shear bands can form in the presence of a weak gravitational field just as on Earth.

We investigate the role of gravity on convection in a dense granular shear flow. Using a microgravity modified Taylor-Couette shear cell under the conditions of parabolic flight microgravity, we demonstrate experimentally that secondary, convective-like flows in a sheared granular material are close to zero in microgravity and enhanced under high-gravity conditions, though the primary flow fields are unaffected by gravity. We suggest that gravity tunes the frictional particle-particle and particle-wall interactions, which have been proposed to drive the secondary flow. In addition, the degree of plastic deformation increases with increasing gravitational forces, supporting the notion that friction is the ultimate cause.

Despite their very low surface gravities, the surfaces of asteroids and comets are covered by granular materials - regolith - that can range from a fine dust to a gravel-like structure of varying depths. Understanding the dynamics of granular materials is, therefore, vital for the interpretation of the surface geology of these small bodies and is also critical for the design and/or operations of any device planned to interact with their surfaces. We present the first measurements of transient weakening of granular material after shear reversal in microgravity as well as a summary of experimental results recently published in other journals, which may have important implications for small-body surfaces. Our results suggest that the force contact network within a granular material may be weaker in microgravity, although the influence of any change in the contact network is felt by the granular material over much larger distances. This could mean that small body surfaces are even more unstable than previously imagined. However, our results also indicate that the consequences of, e.g., a meteorite impact or a spacecraft landing, may be very different depending on the impact angle and location, and depending on the prior history of the small body surface.