Normalized to: Mumby, G.
[1]
oai:arXiv.org:1607.05754 [pdf] - 1531066
Mechanical design and development of TES bolometer detector arrays for
the Advanced ACTPol experiment
Ward, Jonathan T.;
Austermann, Jason;
Beall, James A.;
Choi, Steve K.;
Crowley, Kevin T.;
Devlin, Mark J.;
Duff, Shannon M.;
Gallardo, Patricio M.;
Henderson, Shawn W.;
Ho, Shuay-Pwu Patty;
Hilton, Gene;
Hubmayr, Johannes;
Khavari, Niloufar;
Klein, Jeffrey;
Koopman, Brian J.;
Li, Dale;
McMahon, Jeffrey;
Mumby, Grace;
Nati, Federico;
Niemack, Michael D.;
Page, Lyman A.;
Salatino, Maria;
Schillaci, Alessandro;
Schmitt, Benjamin L.;
Simon, Sara M.;
Staggs, Suzanne T.;
Thornton, Robert;
Ullom, Joel N.;
Vavagiakis, Eve M.;
Wollack, Edward J.
Submitted: 2016-07-19
The next generation Advanced ACTPol (AdvACT) experiment is currently underway
and will consist of four Transition Edge Sensor (TES) bolometer arrays, with
three operating together, totaling ~5800 detectors on the sky. Building on
experience gained with the ACTPol detector arrays, AdvACT will utilize various
new technologies, including 150mm detector wafers equipped with multichroic
pixels, allowing for a more densely packed focal plane. Each set of detectors
includes a feedhorn array of stacked silicon wafers which form a spline profile
leading to each pixel. This is then followed by a waveguide interface plate,
detector wafer, back short cavity plate, and backshort cap. Each array is
housed in a custom designed structure manufactured from high purity copper and
then gold plated. In addition to the detector array assembly, the array package
also encloses cryogenic readout electronics. We present the full mechanical
design of the AdvACT high frequency (HF) detector array package along with a
detailed look at the detector array stack assemblies. This experiment will also
make use of extensive hardware and software previously developed for ACT, which
will be modified to incorporate the new AdvACT instruments. Therefore, we
discuss the integration of all AdvACT arrays with pre-existing ACTPol
infrastructure.
[2]
oai:arXiv.org:1511.04414 [pdf] - 1449883
Cosmology Large Angular Scale Surveyor (CLASS) Focal Plane Development
Chuss, D. T.;
Ali, A.;
Amiri, M.;
Appel, J.;
Bennett, C. L.;
Colazo, F.;
Denis, K. L.;
Dünner, R.;
Essinger-Hileman, T.;
Eimer, J.;
Fluxa, P.;
Gothe, D.;
Halpern, M.;
Harrington, K.;
Hilton, G.;
Hinshaw, G.;
Hubmayr, J.;
Iuliano, J.;
Marriage, T. A.;
Miller, N.;
Moseley, S. H.;
Mumby, G.;
Petroff, M.;
Reintsema, C.;
Rostem, K.;
U-Yen, K.;
Watts, D.;
Wagner, E.;
Wollack, E. J.;
Xu, Z.;
Zeng, L.
Submitted: 2015-11-13
The Cosmology Large Angular Scale Surveyor (CLASS) will measure the
polarization of the Cosmic Microwave Background to search for and characterize
the polarized signature of inflation. CLASS will operate from the Atacama
Desert and observe $\sim$70% of the sky. A variable-delay polarization
modulator (VPM) modulates the polarization at $\sim$10 Hz to suppress the 1/f
noise of the atmosphere and enable the measurement of the large angular scale
polarization modes. The measurement of the inflationary signal across angular
scales that span both the recombination and reionization features allows a test
of the predicted shape of the polarized angular power spectra in addition to a
measurement of the energy scale of inflation.
CLASS is an array of telescopes covering frequencies of 38, 93, 148, and 217
GHz. These frequencies straddle the foreground minimum and thus allow the
extraction of foregrounds from the primordial signal. Each focal plane contains
feedhorn-coupled transition-edge sensors that simultaneously detect two
orthogonal linear polarizations. The use of single-crystal silicon as the
dielectric for the on-chip transmission lines enables both high efficiency and
uniformity in fabrication. Integrated band definition has been implemented that
both controls the bandpass of the single mode transmission on the chip and
prevents stray light from coupling to the detectors.