AstroSat is a multi-wavelength satellite launched on 2015 September 28. The CZT Imager of AstroSat on its very first day of operation detected a long duration gamma-ray burst (GRB) namely GRB 151006A. Using the off-axis imaging and spectral response of the instrument, we demonstrate that CZT Imager can localise this GRB correct to about a few degrees and it can provide, in conjunction with Swift, spectral parameters similar to that obtained from Fermi/GBM. Hence CZT Imager would be a useful addition to the currently operating GRB instruments (Swift and Fermi). Specifically, we argue that the CZT Imager will be most useful for the short hard GRBs by providing localisation for those detected by Fermi and spectral information for those detected only by Swift. We also provide preliminary results on a new exciting capability of this instrument: CZT Imager is able to identify Compton scattered events thereby providing polarisation information for bright GRBs. GRB 151006A, in spite of being relatively faint, shows hints of a polarisation signal at 100-300 keV (though at a low significance level). We point out that CZT Imager should provide significant time resolved polarisation measurements for GRBs that have fluence 3 times higher than that of GRB 151006A. We estimate that the number of such bright GRBs detectable by CZT Imager is 5 - 6 per year. CZT Imager can also act as a good hard X-ray monitoring device for possible electromagnetic counterparts of Gravitational Wave events.

Charged Particle Monitor (CPM) on-board the AstroSat satellite is an instrument designed to detect the flux of charged particles at the satellite location. A Cesium Iodide Thallium (CsI(Tl)) crystal is used with a Kapton window to detect protons with energies greater than 1 MeV. The ground calibration of CPM was done using gamma-rays from radioactive sources and protons from particle accelerators. Based on the ground calibration results, energy deposition above 1 MeV are accepted and particle counts are recorded. It is found that CPM counts are steady and the signal for the onset and exit of South Atlantic Anomaly (SAA) region are generated in a very reliable and stable manner.

The Cadmium Zinc Telluride Imager (CZTI) is a high energy, wide-field imaging instrument on AstroSat. CZT's namesake Cadmium Zinc Telluride detectors cover an energy range from 20 keV to > 200 keV, with 11% energy resolution at 60 keV. The coded aperture mask attains an angular resolution of 17' over a 4.6 deg x 4.6 deg (FWHM) field of view. CZTI functions as an open detector above 100 keV, continuously sensitive to GRBs and other transients in about 30% of the sky. The pixellated detectors are sensitive to polarisation above ~100 keV, with exciting possibilities for polarisation studies of transients and bright persistent sources. In this paper, we provide details of the complete CZTI instrument, detectors, coded aperture mask, mechanical and electronic configuration, as well as data and products.

Cadmium Zinc Telluride (CZT) detectors are high sensitivity and high resolution devices for hard X-ray imaging and spectroscopic studies. The new series of CZT detector modules (OMS40G256) manufactured by Orbotech Medical Solutions (OMS), Israel, are used in the RT-2/CZT payload onboard the CORONAS-PHOTON satellite. The CZT detectors, sensitive in the energy range of 20 keV to 150 keV, are used to image solar flares in hard X-rays. Since these modules are essentially manufactured for commercial applications, we have carried out a series of comprehensive tests on these modules so that they can be confidently used in space-borne systems. These tests lead us to select the best three pieces of the 'Gold' modules for the RT-2/CZT payload. This paper presents the characterization of CZT modules and the criteria followed for selecting the ones for the RT-2/CZT payload. The RT-2/CZT payload carries, along with three CZT modules, a high spatial resolution CMOS detector for high resolution imaging of transient X-ray events. Therefore, we discuss the characterization of the CMOS detector as well.

The onboard software and data communication in the RT-2 Experiment onboard the Coronas-Photon satellite is organized in a hierarchical way to effectively handle and communicate asynchronous data generated by the X-ray detectors. A flexible data handling system is organized in the X-ray detector packages themselves and the processing electronic device, namely RT-2/E, has the necessary intelligence to communicate with the 3 scientific payloads by issuing commands and receiving data. It has direct interfacing with the Satellite systems and issues commands to the detectors and processes the detector data before sending to the satellite systems. The onboard software is configured with several novel features like a) device independent communication scheme, b) loss-less data compression and c) Digital Signal Processor. Functionality of the onboard software along with the data structure, command structure, complex processing scheme etc. are discussed in this paper.

We present the results of an analysis of the prompt gamma-ray emission from GRB 090618 using the RT-2 Experiment onboard the Coronas-Photon satellite. GRB 090618 shows multiple peaks and a detailed study of the temporal structure as a function of energy is carried out. As the GRB was incident at an angle of 77 degree to the detector axis, we have generated appropriate response functions of the detectors to derive the spectrum of this GRB. We have augmented these results using the publicly available data from the Swift BAT detector and show that a combined spectral analysis can measure the spectral parameters quite accurately. We also attempt a spectral and timing analysis of individual peaks and find evidence for a systematic change in the pulse emission characteristics for the successive pulses. In particular, we find that the peak energy of the spectrum, E_p, is found to monotonically decrease with time, for the successive pulses of this GRB.

Phoswich detectors (RT-2/S & RT-2/G) are major scientific payloads of the RT-2 Experiment onboard the CORONAS-PHOTON mission, which was launched into a polar Low Earth Orbit of around 550 km on 2009 January 30. These RT-2 instruments are designed and developed to observe solar flares in hard X-rays and to understand the energy transport processes associated with these flares. Apart from this, these instruments are capable of observing Gamma Ray Bursts (GRBs) and Cosmic diffuse X-ray background (CDXRB). Both detectors consist of identical NaI(Tl) and CsI(Na) scintillation crystals in a Phoswich combination, having the same diameter (116 mm) but different thicknesses. The normal working energy range is from 15 keV to 150 keV, but may be extendable up to ~ 1 MeV. In this paper, we present the RT-2/S and RT-2/G instruments and discuss their testing and calibration results. We used different radio-active sources to calibrate both detectors. The radio-active source Co^57 (122 keV) is used for onboard calibration of both instruments. During its lifetime (~ 3-5 years), RT-2 is expected to cover the peak of the 24th solar cycle.

We present the results of an analysis of hard X-ray observations of the C2.7 solar flare detected by the RT-2 Experiment onboard the Coronas - Photon satellite. We detect hard X-ray pulsations at periods of ~12 s and ~15 s. We find a marginal evidence for a decrease in period with time. We have augmented these results using the publicly available data from the RHESSI satellite. We present a spectral analysis and measure the spectral parameters.

Calibration of X-ray detectors is very important to understand the performance characteristics of the detectors and their variation with time and changing operational conditions. This enables the most accurate translation of the measurements to absolute and relative values of the incident X-ray photon energy so that physical models of the source emission can be tested. It is a general practice to put a known X-ray source (radio active source) in the detector housing for the calibration purpose. This, however, increases the background. Tagging the calibration source with the signal from a simultaneously emitted charge particle (like alpha particle) can identify the X-ray event used for calibration. Here in this paper, we present a new design for an alpha-tagged X-ray source using Am^241 radio active source and describe its performance characteristics. Its application for the upcoming Astrosat satellite is also discussed.

RT-2 Experiment (RT - Roentgen Telescope) is a low energy gamma-ray instrument which is designed and developed as a part of Indo-Russian collaborative project of CORONAS-PHOTON Mission to study the Solar flares in wide energy band of electromagnetic spectrum ranging from UV to high-energy gamma-rays (~2000 MeV). RT-2 instruments will cover the energy range of 15 keV to 150 keV extendable up to ~1 MeV. It consists of three detectors (two Phoswich detectors, namely, RT-2/S, RT-2/G and one solid-state imaging detector RT-2/CZT) and one processing electronic device (RT-2/E). Both Phoswich detectors will have time resolved spectrum, whereas the solid-state imaging detector will have high resolved image of the solar flares in hard X-rays. We have used Co-57 (122 keV) radio-active source for onboard calibration of all three detectors. In this paper, we briefly discuss the in-flight performance of RT-2 instruments and present initial flight data from the instruments. This mission was launched into polar LEO (Low Earth Orbit) (~550 km) on 30th January 2009 from Plesetsk Cosmodrome, Russia.

New generation Cadmium Telluride (CZT & CdTe) solid state detectors can provide high quantum efficiency with reasonably good energy resolution and can operate at near room temperature; an unique advantage for space experiments. We present here results of our study of small diode detectors as well as large area pixel detectors. Our study is aimed at developing near room temperature hard X-ray spectroscopy detectors for ASTROSAT and other future Indian space science missions.We have studied a Si-PIN detector in the energy range 5 - 60 keV and CZT & CdTe Schottky diode detectors in the energy region 10 - 1330 keV. We have studied large area (64 cm$^2$) CZT pixel detectors with pixel size close to the small CZT detector. We have studied individual pixels as well as CZT detector as a whole (summed over all the 1024 pixels). The energy resolution behaviour of the large area CZT detector is similar to that of small diode detectors in the low energy region. The change in operating temperature from room temperature ~20 to ~70$ degree C drastically affects both the energy resolutionas well as the peak area due to a sharp rise in the thermal noise.These results suggest that the cooling of detector system will provide better energy resolution as well as detection efficiency.