Comparing chemical abundances of a planet and the host star reveals the origin and formation path. Stellar abundance is measured with high-resolution spectroscopy. Planet abundance, on the other hand, is usually inferred from low-resolution data. For directly imaged exoplanets, the data are available from a slew of high-contrast imaging/spectroscopy instruments. Here, we study the chemical abundance of HR 8799 and its planet c. We measure stellar abundance using LBT/PEPSI (R=120,000) and archival HARPS data: stellar [C/H], [O/H], and C/O are 0.11$\pm$0.12, 0.12$\pm$0.14, and 0.54$^{+0.12}_{-0.09}$, all consistent with solar values. We conduct atmospheric retrieval using newly obtained Subaru/CHARIS data together with archival Gemini/GPI and Keck/OSIRIS data. We model the planet spectrum with petitRADTRANS and conduct retrieval using PyMultiNest. Retrieved planetary abundance can vary by $\sim$0.5 dex, from sub-stellar to stellar C and O abundances. The variation depends on whether strong priors are chosen to ensure a reasonable planet mass. Moreover, comparison with previous works also reveals inconsistency in abundance measurements. We discuss potential issues that can cause the inconsistency, e.g., systematics in individual data sets and different assumptions in the physics and chemistry in retrieval. We conclude that no robust retrieval can be obtained unless the issues are fully resolved.

High-contrast imaging (HCI) observations of exoplanets can be limited by the island effect (IE). On the current generation of telescopes, the IE becomes a severe problem when the ground wind speed is below a few meters per second. This is referred to as the low-wind effect (LWE). The LWE severely distorts the point spread function (PSF), significantly lowering the Strehl ratio and degrading the contrast. In this article, we aim to show that the focal-plane wavefront sensing (FPWFS) algorithm, Fast and Furious (F&F), can be used to measure and correct the IE/LWE. We deployed the algorithm on the SCExAO HCI instrument at the Subaru Telescope using the internal near-infrared camera in H-band. We tested F&F with the internal source, and it was deployed on-sky to test its performance with the full end-to-end system and atmospheric turbulence. The performance of the algorithm was evaluated by two metrics based on the PSF quality: 1) the Strehl ratio approximation ($SRA$), and 2) variance of the normalized first Airy ring ($VAR$). Random LWE phase screens with a peak-to-valley wavefront error between 0.4 $\mu$m and 2 $\mu$m were all corrected to a $SRA$ $>$90\% and an $VAR\lessapprox0.05$. Furthermore, the on-sky results show that F&F is able to improve the PSF quality during very challenging atmospheric conditions (1.3-1.4'' seeing at 500 nm). Closed-loop tests show that F&F is able to improve the $VAR$ from 0.27 to 0.03 and therefore significantly improve the symmetry of the PSF. Simultaneous observations of the PSF in the {optical} ($\lambda = $ 750 nm, $\Delta \lambda =$ 50 nm) show that during these tests we were correcting aberrations common to the optical and NIR paths within SCExAO. Going forward, the algorithm is suitable for incorporation into observing modes, which will enable PSFs of higher quality and stability during science observations.

To reach its optimal performance, Fizeau interferometry requires that we work to resolve instrumental biases through calibration. One common technique used in high contrast imaging is angular differential imaging, which calibrates the point spread function and flux leakage using a rotation in the focal plane. Our aim is to experimentally demonstrate and validate the efficacy of an angular differential kernel-phase approach, a new method for self-calibrating interferometric observables that operates similarly to angular differential imaging, while retaining their statistical properties. We used linear algebra to construct new observables that evolve outside of the subspace spanned by static biases. On-sky observations of a binary star with the SCExAO instrument at the Subaru telescope were used to demonstrate the practicality of this technique. We used a classical approach on the same data to compare the effectiveness of this method. The proposed method shows smaller and more Gaussian residuals compared to classical calibration methods, while retaining compatibility with the statistical tools available. We also provide a measurement of the stability of the SCExAO instrument that is relevant to the application of the technique. Angular differential kernel phases provide a reliable method for calibrating biased observables. Although the sensitivity at small separations is reduced for small field rotations, the calibration is effectively improved and the number of subjective choices is reduced.

We analyzed the young (2.8-Myr-old) binary system FS Tau A using near-infrared (H-band) high-contrast polarimetry data from Subaru/HiCIAO and sub-millimeter CO (J=2-1) line emission data from ALMA. Both the near-infrared and sub-millimeter observations reveal several clear structures extending to $\sim$240 AU from the stars. Based on these observations at different wavelengths, we report the following discoveries. One arm-like structure detected in the near-infrared band initially extends from the south of the binary with a subsequent turn to the northeast, corresponding to two bar-like structures detected in ALMA observations with an LSRK velocity of 1.19-5.64 km/s. Another feature detected in the near-infrared band extends initially from the north of the binary, relating to an arm-like structure detected in ALMA observations with an LSRK velocity of 8.17-16.43 km/s. From their shapes and velocities, we suggest that these structures can mostly be explained by two streamers that connect the outer circumbinary disk and the central binary components. These discoveries will be helpful for understanding the evolution of streamers and circumstellar disks in young binary systems.

The Low Wind Effect (LWE) refers to a phenomenon that occurs when the wind speed inside a telescope dome drops below $3$m/s creating a temperature gradient near the telescope spider. This produces phase discontinuities in the pupil plane that are not detected by traditional Adaptive Optics (AO) systems such as the pyramid wavefront sensor or the Shack-Hartmann. Considering the pupil as divided in 4 quadrants by regular spiders, the phase discontinuities correspond to piston, tip and tilt aberrations in each quadrant of the pupil. Uncorrected, it strongly decreases the ability of high contrast imaging instruments utilizing coronagraphy to detect exoplanets at small angular separations. Multiple focal plane wavefront sensors are currently being developed and tested on the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument at Subaru Telescope: Among them, the Zernike Asymmetric Pupil (ZAP) wavefront sensor already showed on-sky that it could measure the LWE induced aberrations in focal plane images. The Fast and Furious algorithm, using previous deformable mirror commands as temporal phase diversity, showed in simulations its efficiency to improve the wavefront quality in the presence of LWE. A Neural Network algorithm trained with SCExAO telemetry showed promising PSF prediction on-sky. The Linearized Analytic Phase Diversity (LAPD) algorithm is a solution for multi-aperture cophasing and is studied to correct for the LWE aberrations by considering the Subaru Telescope as a 4 sub-aperture instrument. We present the different algorithms, show the latest results and compare their implementation on SCExAO/SUBARU as real-time wavefront sensors for the LWE compensation.

The SR24 multi-star system hosts both circumprimary and circumsecondary disks, which are strongly misaligned from each other. The circumsecondary disk is circumbinary in nature. Interestingly, both disks are interacting, and they possibly rotate in opposite directions. To investigate the nature of this unique twin disk system, we present 0.''1 resolution near-infrared polarized intensity images of the circumstellar structures around SR24, obtained with HiCIAO mounted on the Subaru 8.2 m telescope. Both the circumprimary disk and the circumsecondary disk are resolved and have elongated features. While the position angle of the major axis and radius of the NIR polarization disk around SR24S are 55$^{\circ}$ and 137 au, respectively, those around SR24N are 110$^{\circ}$ and 34 au, respectively. With regard to overall morphology, the circumprimary disk around SR24S shows strong asymmetry, whereas the circumsecondary disk around SR24N shows relatively strong symmetry. Our NIR observations confirm the previous claim that the circumprimary and circumsecondary disks are misaligned from each other. Both the circumprimary and circumsecondary disks show similar structures in $^{12}$CO observations in terms of its size and elongation direction. This consistency is because both NIR and $^{12}$CO are tracing surface layers of the flared disks. As the radius of the polarization disk around SR24N is roughly consistent with the size of the outer Roche lobe, it is natural to interpret the polarization disk around SR24N as a circumbinary disk surrounding the SR24Nb-Nc system.

We present $\kappa$ Andromeda b's photometry and astrometry taken with Subaru/SCExAO+HiCIAO and Keck/NIRC2, combined with recently published SCExAO/CHARIS low-resolution spectroscopy and published thermal infrared photometry to further constrain the companion's atmospheric properties and orbit. $\kappa$ And b's Y/Y-K colors are redder than field dwarfs, consistent with its youth and lower gravity. Empirical comparisons of its Y-band photometry and CHARIS spectrum to a large spectral library of isolated field dwarfs reaffirm the conclusion from Currie et al. (2018) that it likely has a low gravity but admit a wider range of most plausible spectral types (L0-L2). Our gravitational classification also suggests that the best-fit objects for $\kappa$ And b may have lower gravity than those previously reported. Atmospheric models lacking dust/clouds fail to reproduce its entire 1--4.7 $\mu m$ spectral energy distribution, cloudy atmosphere models with temperatures of $\sim$ 1700--2000 $K$ better match $\kappa$ And b data. Most well-fitting model comparisons favor 1700--1900 $K$, a surface gravity of log(g) $\sim$ 4--4.5, and a radius of 1.3--1.6\,$R_{\rm Jup}$; the best-fit model (DRIFT-Phoenix) yields the coolest and lowest-gravity values: $T_{\rm eff}$=1700 K and $\log g$=4.0. An update to $\kappa$ And b's orbit with ExoSOFT using new astrometry spanning seven years reaffirms its high eccentricity ($0.77\pm0.08$). We consider a scenario where unseen companions are responsible for scattering $\kappa$ And b to a wide separation and high eccentricity. If three planets, including $\kappa$ And b, were born with coplanar orbits and one of them was ejected by gravitational scattering, a potential inner companion with mass $\gtrsim10M_{\rm Jup}$ could be located at $\lesssim$ 25 au.

The characterisation of exoplanets is critical to understanding planet diversity and formation, their atmospheric composition and the potential for life. This endeavour is greatly enhanced when light from the planet can be spatially separated from that of the host star. One potential method is nulling interferometry, where the contaminating starlight is removed via destructive interference. The GLINT instrument is a photonic nulling interferometer with novel capabilities that has now been demonstrated in on-sky testing. The instrument fragments the telescope pupil into sub-apertures that are injected into waveguides within a single-mode photonic chip. Here, all requisite beam splitting, routing and recombination is performed using integrated photonic components. We describe the design, construction and laboratory testing of our GLINT pathfinder instrument. We then demonstrate the efficacy of this method on sky at the Subaru Telescope, achieving a null-depth precision on sky of $\sim10^{-4}$ and successfully determining the angular diameter of stars (via their null-depth measurements) to milli-arcsecond accuracy. A statistical method for analysing such data is described, along with an outline of the next steps required to deploy this technique for cutting-edge science.

We describe the current performance of the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument on the Subaru telescope on Maunakea, Hawaii and present early science results for SCExAO coupled with the CHARIS integral field spectrograph. SCExAO now delivers H band Strehl ratios up to $\sim$ 0.9 or better, extreme AO corrections for optically faint stars, and planet-to-star contrasts rivaling that of GPI and SPHERE. CHARIS yield high signal-to-noise detections and 1.1--2.4 $\mu m$ spectra of benchmark directly-imaged companions like HR 8799 cde and kappa And b that clarify their atmospheric properties. We also show how recently published as well as unpublished observations of LkCa 15 lead to a re-evaluation of its claimed protoplanets. Finally, we briefly describe plans for a SCExAO-focused direct imaging campaign to directly image and characterize young exoplanets, planet-forming disks, and (later) mature planets in reflected light.

In this article we show that the vector-Apodizing Phase Plate (vAPP) coronagraph can be designed such that the coronagraphic point spread functions (PSFs) can act as a wavefront sensor to measure and correct the (quasi-)static aberrations, without dedicated wavefront sensing holograms nor modulation by the deformable mirror. The absolute wavefront retrieval is performed with a non-linear algorithm. The focal-plane wavefront sensing (FPWFS) performance of the vAPP and the algorithm are evaluated with numerical simulations, to test various photon and read noise levels, the sensitivity to the 100 lowest Zernike modes and the maximum wavefront error (WFE) that can be accurately estimated in one iteration. We apply these methods to the vAPP within SCExAO, first with the internal source and subsequently on-sky. In idealised simulations we show that for $10^7$ photons the root-mean-square (RMS) WFE can be reduced to $\sim\lambda/1000$, which is 1 nm RMS in the context of the SCExAO system. We find that the maximum WFE that can be corrected in one iteration is $\sim\lambda/8$ RMS or $\sim$200 nm RMS (SCExAO). Furthermore, we demonstrate the SCExAO vAPP capabilities by measuring and controlling the lowest 30 Zernike modes with the internal source and on-sky. On-sky, we report a raw contrast improvement of a factor $\sim$2 between 2 and 4 $\lambda/D$ after 5 iterations of closed-loop correction. When artificially introducing 150 nm RMS WFE, the algorithm corrects it within 5 iterations of closed-loop operation. FPWFS with the vAPP's coronagraphic PSFs is a powerful technique since it integrates coronagraphy and wavefront sensing, eliminating the need for additional probes and thus resulting in a $100\%$ science duty cycle and maximum throughput for the target.

The fields of Astronomy and Astrophysics are technology limited, where the advent and application of new technologies to astronomy usher in a flood of discoveries altering our understanding of the Universe (e.g., recent cases include LIGO and the GRAVITY instrument at the VLTI). Currently, the field of astronomical spectroscopy is rapidly approaching an impasse: the size and cost of instruments, especially multi-object and integral field spectrographs for extremely large telescopes (ELTs), are pushing the limits of what is feasible, requiring optical components at the very edge of achievable size and performance. For these reasons, astronomers are increasingly looking for innovative solutions like photonic technologies that promote instrument miniaturization and simplification, while providing superior performance. Astronomers have long been aware of the potential of photonic technologies. The goal of this white paper is to draw attention to key photonic technologies and developments over the past two decades and demonstrate there is new momentum in this arena. We outline where the most critical efforts should be focused over the coming decade in order to move towards realizing a fully photonic instrument. A relatively small investment in this technology will advance astronomical photonics to a level where it can reliably be used to solve challenging instrument design limitations. For the benefit of both ground and space borne instruments alike, an endorsement from the National Academy of Sciences decadal survey will ensure that such solutions are set on a path to their full scientific exploitation, which may one day address a broad range of science cases outlined in the KSPs.

Optical and near-IR Microwave Kinetic Inductance Detectors, or MKIDs, are superconducting photon counting detectors capable of measuring the energy and arrival time of individual OIR photons without read noise or dark current. In this whitepaper we will discuss the current status of OIR MKIDs and MKID-based instruments.

We present an analysis of instrument performance using new observations taken with the Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS) instrument and the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system. In a correlation analysis of our datasets (which use the broadband mode covering J through K band in a single spectrum), we find that chromaticity in the SCExAO/CHARIS system is generally worse than temporal stability. We also develop a point spread function (PSF) subtraction pipeline optimized for the CHARIS broadband mode, including a forward modelling-based exoplanet algorithmic throughput correction scheme. We then present contrast curves using this newly developed pipeline. An analogous subtraction of the same datasets using only the H band slices yields the same final contrasts as the full JHK sequences; this result is consistent with our chromaticity analysis, illustrating that PSF subtraction using spectral differential imaging (SDI) in this broadband mode is generally not more effective than SDI in the individual J, H, or K bands. In the future, the data processing framework and analysis developed in this paper will be important to consider for additional SCExAO/CHARIS broadband observations and other ExAO instruments which plan to implement a similar integral field spectrograph broadband mode.

Over the past three decades instruments on the ground and in space have discovered thousands of planets outside the solar system. These observations have given rise to an astonishingly detailed picture of the demographics of short-period planets, but are incomplete at longer periods where both the sensitivity of transit surveys and radial velocity signals plummet. Even more glaring is that the spectra of planets discovered with these indirect methods are either inaccessible (radial velocity detections) or only available for a small subclass of transiting planets with thick, clear atmospheres. Direct detection can be used to discover and characterize the atmospheres of planets at intermediate and wide separations, including non-transiting exoplanets. Today, a small number of exoplanets have been directly imaged, but they represent only a rare class of young, self-luminous super-Jovian-mass objects orbiting tens to hundreds of AU from their host stars. Atmospheric characterization of planets in the <5 AU regime, where radial velocity (RV) surveys have revealed an abundance of other worlds, is technically feasible with 30-m class apertures in combination with an advanced AO system, coronagraph, and suite of spectrometers and imagers. There is a vast range of unexplored science accessible through astrometry, photometry, and spectroscopy of rocky planets, ice giants, and gas giants. In this whitepaper we will focus on one of the most ambitious science goals --- detecting for the first time habitable-zone rocky (<1.6 R_Earth) exoplanets in reflected light around nearby M-dwarfs

Two studies utilizing sparse aperture masking (SAM) interferometry and $H_{\rm \alpha}$ differential imaging have reported multiple jovian companions around the young solar-mass star, LkCa 15 (LkCa 15 bcd): the first claimed direct detection of infant, newly-formed planets ("protoplanets"). We present new near-infrared direct imaging/spectroscopy from the SCExAO system coupled with the CHARIS integral field spectrograph and multi-epoch thermal infrared imaging from Keck/NIRC2 of LkCa 15 at high Strehl ratios. These data provide the first direct imaging look at the same wavelengths and in the same locations where previous studies identified the LkCa 15 protoplanets and thus offer the first decisive test of their existence. The data do not reveal these planets. Instead, we resolve extended emission tracing a dust disk with a brightness and location comparable to that claimed for LkCa 15 bcd. Forward-models attributing this signal to orbiting planets are inconsistent with the combined SCExAO/CHARIS and Keck/NIRC2 data. An inner disk provides a more compelling explanation for the SAM detections and perhaps also the claimed $H_{\alpha}$ detection of LkCa 15 b. We conclude that there is currently no clear, direct evidence for multiple protoplanets orbiting LkCa 15, although the system likely contains at least one unseen jovian companion. To identify jovian companions around LkCa 15 from future observations, the inner disk should be detected and its effect modeled, removed, and shown to be distinguishable from planets. Protoplanet candidates identified from similar systems should likewise be clearly distinguished from disk emission through modeling.

We present H-band polarized scattered light imagery and JHK high-contrast spectroscopy of the protoplanetary disk around HD 163296 observed with the HiCIAO and SCExAO/CHARIS instruments at Subaru Observatory. The polarimetric imagery resolve a broken ring structure surrounding HD 163296 that peaks at a distance along the major axis of 0.65 (66 AU) and extends out to 0.98 (100 AU) along the major axis. Our 2011 H-band data exhibit clear axisymmetry, with the NW- and SE- side of the disk exhibiting similar intensities. Our data are clearly different than 2016 epoch H-band observations from VLT/SPHERE that found a strong 2.7x asymmetry between the NW- and SE-side of the disk. Collectively, these results indicate the presence of time variable, non-azimuthally symmetric illumination of the outer disk. Based on our 3D-MCRT modeling of contemporaneous IR spectroscopic and H-band polarized intensity imagery of the system, we suggest that while the system could plausibly host an inclined inner disk component, such a component is unlikely to be responsible for producing the observed time-dependent azimuthal variations in the outer scattered light disk of the system. While our SCExAO/CHARIS data are sensitive enough to recover the planet candidate identified from NIRC2 in the thermal IR, we fail to detect an object with a corresponding JHK brightness estimated from the atmospheric models of Baraffe et al. 2003. This suggests that the candidate is either fainter in JHK bands than model predictions, possibly due to extinction from the disk or atmospheric dust/clouds, or that it is an artifact of the dataset/data processing. Our SCExAO/CHARIS data lower the IR mass limits for planets inferred at larger stellocentric separations; however, these ALMA-predicted protoplanet candidates are currently still consistent with direct imaging constraints.

We have now accumulated a wealth of observations of the planet-formation environment and of mature planetary systems. These data allow us to test and refine theories of gas-giant planet formation by placing constraints on the conditions and timescale of this process. Yet a number of fundamental questions remain unanswered about how protoplanets accumulate material, their photospheric properties and compositions, and how they interact with protoplanetary disks. While we have begun to detect protoplanet candidates during the last several years, we are presently only sensitive to the widest separation, highest mass / accretion rate cases. Current observing facilities lack the angular resolution and inner working angle to probe the few-AU orbital separations where giant planet formation is thought to be most efficient. They also lack the contrast to detect accretion rates that would form lower mass gas giants and ice giants. Instruments and telescopes coming online over the next decade will provide high contrast in the inner giant-planet-forming regions around young stars, allowing us to build a protoplanet census and to characterize planet formation in detail for the first time.

Wavefront sensing and control are important for enabling one of the key advantages of using large apertures, namely higher angular resolutions. Pyramid wavefront sensors are becoming commonplace in new instrument designs owing to their superior sensitivity. However, one remaining roadblock to their widespread use is the fabrication of the pyramidal optic. This complex optic is challenging to fabricate due to the pyramid tip, where four planes need to intersect in a single point. Thus far, only a handful of these have been produced due to the low yields and long lead times. To address this, we present an alternative implementation of the pyramid wavefront sensor that relies on two roof prisms instead. Such prisms are easy and inexpensive to source. We demonstrate the successful operation of the roof prism pyramid wavefront sensor on a 8-m class telescope, at visible and near infrared wavelengths ---for the first time using a SAPHIRA HgCdTe detector without modulation for a laboratory demonstration---, and elucidate how this sensor can be used more widely on wavefront control test benches and instruments.

We present SCExAO/CHARIS 1.1--2.4 micron integral field direct spectroscopy of the young HIP 79124 triple system. HIP 79124 is a member of the Scorpius-Centaurus association, consisting of an A0V primary with two low-mass companions at a projected separation of <1 arcsecond. Thanks to the high quality wavefront corrections provided by SCExAO, both companions are decisively detected without the employment of any PSF-subtraction algorithm to eliminate quasi-static noise. The spectrum of the outer C object is very well matched by Upper Scorpius M4 pm 0.5 standard spectra, with a Teff = 2945 pm 100 and a mass of 350 MJup. HIP 79124 B is detected at a separation of only 180 mas in a highly-correlated noise regime, and it falls in the spectral range M6 pm 0.5 with Teff = 2840 pm 190 and 100 MJup. Previous studies of stellar populations in Sco-Cen have highlighted a discrepancy in isochronal ages between the lower-mass and higher-mass populations. This could be explained either by an age spread in the region, or by conventional isochronal models failing to reproduce the evolution of low-mass stars. The HIP 79124 system should be coeval, and therefore it provides an ideal laboratory to test these scenarios. We place the three components in a color-magnitude diagram and find that the models predict a younger age for the two low-mass companions (3 Myr) than for the primary star (6 Myr). These results imply that the omission of magnetic effects in conventional isochronal models inhibit them from reproducing early low-mass stellar evolution, which is further supported by the fact that new models that include such effects provide more consistent ages in the HIP 79124 system.

We present new, near-infrared (1.1--2.4 $\mu m$) high-contrast imaging of the bright debris disk surrounding HIP 79977 with the Subaru Coronagraphic Extreme Adaptive Optics system (SCExAO) coupled with the CHARIS integral field spectrograph. SCExAO/CHARIS resolves the disk down to smaller angular separations of (0.11"; $r \sim 14$ au) and at a higher significance than previously achieved at the same wavelengths. The disk exhibits a marginally significant east-west brightness asymmetry in $H$ band that requires confirmation. Geometrical modeling suggests a nearly edge-on disk viewed at a position angle of $\sim$ 114.6$^{o}$ east of north. The disk is best-fit by scattered-light models assuming strongly forward-scattering grains ($g$ $\sim$ 0.5--0.65) confined to a torus with a peak density at $r_{0}$ $\sim$ 53--75 au. We find that a shallow outer density power law of $\alpha_{out}=$-1-- -3 and flare index of $\beta = 1$ are preferred. Other disk parameters (e.g.~inner density power law and vertical scale height) are more poorly constrained. The disk has a slightly blue intrinsic color and its profile is broadly consistent with predictions from birth ring models applied to other debris disks. While HIP 79977's disk appears to be more strongly forward-scattering than most resolved disks surrounding 5--30 Myr-old stars, this difference may be due to observational biases favoring forward-scattering models for inclined disks vs. lower inclination, ostensibly neutral-scattering disks like HR 4796A's. Deeper, higher signal-to-noise SCExAO/CHARIS data can better constrain the disk's dust composition.

We present SCExAO/CHARIS high-contrast imaging/$JHK$ integral field spectroscopy of $\kappa$ And b, a directly-imaged low-mass companion orbiting a nearby B9V star. We detect $\kappa$ And b at a high signal-to-noise and extract high precision spectrophotometry using a new forward-modeling algorithm for (A-)LOCI complementary to KLIP-FM developed by Pueyo (2016). $\kappa$ And b's spectrum best resembles that of a low-gravity L0--L1 dwarf (L0--L1$\gamma$). Its spectrum and luminosity are very well matched by 2MASSJ0141-4633 and several other 12.5--15 $M_{\rm J}$ free floating members of the 40 $Myr$-old Tuc-Hor Association, consistent with a system age derived from recent interferometric results for the primary, a companion mass at/near the deuterium-burning limit (13$^{+12}_{-2}$ M$_{\rm J}$), and a companion-to-primary mass ratio characteristic of other directly-imaged planets ($q$ $\sim$ 0.005$^{+0.005}_{-0.001}$). We did not unambiguously identify additional, more closely-orbiting companions brighter and more massive than $\kappa$ And b down to $\rho$ $\sim$ 0.3" (15 au). SCExAO/CHARIS and complementary Keck/NIRC2 astrometric points reveal clockwise orbital motion. Modeling points towards a likely eccentric orbit: a subset of acceptable orbits include those that are aligned with the star's rotation axis. However, $\kappa$ And b's semimajor axis is plausibly larger than 75 au and in a region where disk instability could form massive companions. Deeper $\kappa$ And high-contrast imaging and low-resolution spectroscopy from extreme AO systems like SCExAO/CHARIS and higher resolution spectroscopy from Keck/OSIRIS or, later, IRIS on the Thirty Meter Telescope could help clarify $\kappa$ And b's chemistry and whether its spectrum provides an insight into its formation environment.

The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument is an extremely modular high-contrast instrument installed on the Subaru telescope in Hawaii. SCExAO has a dual purpose. Its position in the northern hemisphere on a 8-meter telescope makes it a prime instrument for the detection and characterization of exoplanets and stellar environments over a large portion of the sky. In addition, SCExAO's unique design makes it the ideal instrument to test innovative technologies and algorithms quickly in a laboratory setup and subsequently deploy them on-sky. SCExAO benefits from a first stage of wavefront correction with the facility adaptive optics AO188, and splits the 600-2400 nm spectrum towards a variety of modules, in visible and near infrared, optimized for a large range of science cases. The integral field spectrograph CHARIS, with its J, H or K-band high-resolution mode or its broadband low-resolution mode, makes SCExAO a prime instrument for exoplanet detection and characterization. Here we report on the recent developments and scientific results of the SCExAO instrument. Recent upgrades were performed on a number of modules, like the visible polarimetric module VAMPIRES, the high-performance infrared coronagraphs, various wavefront control algorithms, as well as the real-time controller of AO188. The newest addition is the 20k-pixel Microwave Kinetic Inductance Detector (MKIDS) Exoplanet Camera (MEC) that will allow for previously unexplored science and technology developments. MEC, coupled with novel photon-counting speckle control, brings SCExAO closer to the final design of future high-contrast instruments optimized for Giant Segmented Mirror Telescopes (GSMTs).

Vibrations are a key source of image degradation in ground-based instrumentation, especially for high-contrast imaging instruments. Vibrations reduce the quality of the correction provided by the adaptive optics system, blurring the science image and reducing the sensitivity of most science modules. We studied vibrations using the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument at the Subaru Telescope as it is the most vibration sensitive system installed on the telescope. We observed vibrations for all targets, usually at low frequency, below 10 Hz. Using accelerometers on the telescope, we confirmed that these vibrations were introduced by the telescope itself, and not the instrument. It was determined that they were related to the pitch of the encoders of the telescope drive system, both in altitude and azimuth, with frequencies evolving proportionally to the rotational speed of the telescope. Another strong vibration was found in the altitude axis of the telescope, around the time of transit of the target, when the altitude rotation speed is below 0.12 arcsec/s. These vibrations are amplified by the 10-Hz control loop of the telescope, especially in a region between 4 and 6 Hz. In this work, we demonstrate an accurate characterization of the frequencies of the telescope vibrations using only the coordinates -right ascension and declination- of the target, and provide a means by which we can predict them for any telescope pointing. This will be a powerful tool that can be used by more advanced wavefront control algorithms, especially predictive control, that uses informations about the disturbance to calculate the best correction.

Direct detection, also known as direct imaging, is a method for discovering and characterizing the atmospheres of planets at intermediate and wide separations. It is the only means of obtaining spectra of non-transiting exoplanets. Characterizing the atmospheres of planets in the <5 AU regime, where RV surveys have revealed an abundance of other worlds, requires a 30-m-class aperture in combination with an advanced adaptive optics system, coronagraph, and suite of spectrometers and imagers - this concept underlies planned instruments for both TMT (the Planetary Systems Imager, or PSI) and the GMT (GMagAO-X). These instruments could provide astrometry, photometry, and spectroscopy of an unprecedented sample of rocky planets, ice giants, and gas giants. For the first time habitable zone exoplanets will become accessible to direct imaging, and these instruments have the potential to detect and characterize the innermost regions of nearby M-dwarf planetary systems in reflected light. High-resolution spectroscopy will not only illuminate the physics and chemistry of exo-atmospheres, but may also probe rocky, temperate worlds for signs of life in the form of atmospheric biomarkers (combinations of water, oxygen and other molecular species). By completing the census of non-transiting worlds at a range of separations from their host stars, these instruments will provide the final pieces to the puzzle of planetary demographics. This whitepaper explores the science goals of direct imaging on 30-m telescopes and the technology development needed to achieve them.

MagAO-X is an entirely new "extreme" adaptive optics system for the Magellan Clay 6.5 m telescope, funded by the NSF MRI program starting in Sep 2016. The key science goal of MagAO-X is high-contrast imaging of accreting protoplanets at H$\alpha$. With 2040 actuators operating at up to 3630 Hz, MagAO-X will deliver high Strehls (>70%), high resolution (19 mas), and high contrast ($< 1\times10^{-4}$) at H$\alpha$ (656 nm). We present an overview of the MagAO-X system, review the system design, and discuss the current project status.

Phase-Induced Amplitude Apodization Complex Mask Coronagraphs (PIAACMC) offer high-contrast performance at a small inner-working angle ($\approx$ 1 $\lambda$/D) with high planet throughput ($>$ 70%). The complex mask is a multi-zone, phase-shifting mask comprised of tiled hexagons which vary in depth. Complex masks can be difficult to fabricate as there are many micron-scale hexagonal zones ($>$ 500 on average) with continuous depths ranging over a few microns. Ensuring the broadband PIAACMC design performance carries through to fabricated devices requires that these complex masks are manufactured to within well-defined tolerances. We report on a simulated tolerance analysis of a "toy" PIAACMC design which characterizes the effect of common microfabrication errors on on-axis contrast performance using a simple Monte Carlo method. Moreover, the tolerance analysis provides crucial information for choosing a fabrication process which yields working devices while potentially reducing process complexity. The common fabrication errors investigated are zone depth discretization, zone depth errors, and edge artifacts between zones.

We present early laboratory simulations and extensive on-sky tests validating of the performance of a shaped pupil coronagraph (SPC) behind an extreme-AO corrected beam of the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system. In tests with the SCExAO internal source/wavefront error simulator, the normalized intensity profile for the SPC degrades more slowly than for the Lyot coronagraph as low-order aberrations reduce the Strehl ratio from extremely high values (S.R. $\sim$ 0.93--0.99) to those characteristic of current ground-based extreme AO systems (S.R. $\sim$ 0.74--0.93) and then slightly lower values down to S.R. $\sim$ 0.57. On-sky SCExAO data taken with the SPC and other coronagraphs for brown dwarf/planet-hosting stars HD 1160 and HR 8799 provide further evidence for the SPC's robustness to low-order aberrations. From H-band Strehl ratios of 80% to 70%, the Lyot coronagraph's performance vs. that of the SPC may degrade even faster on sky than is seen in our internal source simulations. The 5-$\sigma$ contrast also degrades faster (by a factor of two) for the Lyot than the SPC. The SPC we use was designed as a technology demonstrator only, with a contrast floor, throughput, and outer working angle poorly matched for SCExAO's current AO performance and poorly tuned for imaging the HR 8799 planets. Nevertheless, we detect HR 8799 cde with SCExAO/CHARIS using the SPC in broadband mode, where the S/N for planet e is within 30% of that obtained using the vortex coronagraph. The shaped-pupil coronagraph is a promising design demonstrated to be robust in the presence of low-order aberrations and may be well-suited for future ground and space-based direct imaging observations, especially those focused on follow-up exoplanet characterization and technology demonstration of deep contrast within well-defined regions of the image plane.

A suite of science instruments is critical to any high contrast imaging facility, as it defines the science capabilities and observing modes available. SCExAO uses a modular approach which allows for state-of-the-art visitor modules to be tested within an observatory environment on an 8-m class telescope. This allows for rapid prototyping of new and innovative imaging techniques that otherwise take much longer in traditional instrument design. With the aim of maturing science modules for an advanced high contrast imager on an giant segmented mirror telescopes (GSMTs) that will be capable of imaging terrestrial planets, we offer an overview and status update on the various science modules currently under test within the SCExAO instrument.

Spectroscopic observations are extremely important for determining the composition, structure, and surface gravity of exoplanetary atmospheres. High resolution spectroscopy of the planet itself has only been demonstrated a handful of times. By using advanced high contrast imagers, it is possible to conduct high resolution spectroscopy on imageable exoplanets, after the star light is first suppressed with an advanced coronagraph. Because the planet is spatially separated in the focal plane, a single mode fiber could be used to collect the light from the planet alone, reducing the photon noise by orders of magnitude. In addition, speckle control applied to the location where an exoplanet is known to exist, can be used to preferentially reject the stellar flux from the fiber further. In this paper we will present the plans for conducting high resolution spectroscopic studies of this nature with the combination of SCExAO and IRD in the H-band on the Subaru Telescope. This technique will be critical to the characterization of terrestrial planets on ELTs and future space missions.

Island effect (IE) aberrations are induced by differential pistons, tips, and tilts between neighboring pupil segments on ground-based telescopes, which severely limit the observations of circumstellar environments on the recently deployed exoplanet imagers (e.g., VLT/SPHERE, Gemini/GPI, Subaru/SCExAO) during the best observing conditions. Caused by air temperature gradients at the level of the telescope spiders, these aberrations were recently diagnosed with success on VLT/SPHERE, but so far no complete calibration has been performed to overcome this issue. We propose closed-loop focal plane wavefront control based on the asymmetric Fourier pupil wavefront sensor (APF-WFS) to calibrate these aberrations and improve the image quality of exoplanet high-contrast instruments in the presence of the IE. Assuming the archetypal four-quadrant aperture geometry in 8m class telescopes, we describe these aberrations as a sum of the independent modes of piston, tip, and tilt that are distributed in each quadrant of the telescope pupil. We calibrate these modes with the APF-WFS before introducing our wavefront control for closed-loop operation. We perform numerical simulations and then experimental tests on a real system using Subaru/SCExAO to validate our control loop in the laboratory and on-sky. Closed-loop operation with the APF-WFS enables the compensation for the IE in simulations and in the laboratory for the small aberration regime. Based on a calibration in the near infrared, we observe an improvement of the image quality in the visible range on the SCExAO/VAMPIRES module with a relative increase in the image Strehl ratio of 37%. Our first IE calibration paves the way for maximizing the science operations of the current exoplanet imagers. Such an approach and its results prove also very promising in light of the Extremely Large Telescopes (ELTs) and the presence of similar artifacts.

The vector vortex is a coronagraphic imaging mode of the recently commissioned Subaru Coronagraphic Extreme-Adaptive Optics (SCExAO) platform on the 8-m Subaru Telescope. This multi-purpose high-contrast visible and near-infrared (R- to K-band) instrument is not only intended to serve as a VLT-class "planet-imager" instrument in the Northern hemisphere, but also to operate as a technology demonstration testbed ahead of the ELTs-era, with a particular emphasis on small inner-working angle (IWA) coronagraphic capabilities. The given priority to small-IWA imaging led to the early design choice to incorporate focal-plane phase-mask coronagraphs. In this context, a test H-band vector vortex liquid crystal polymer waveplate was provided to SCExAO, to allow a one-to-one comparison of different small-IWA techniques on the same telescope instrument, before considering further steps. Here we present a detailed overview of the vector vortex coronagraph, from its installation and performances on the SCExAO optical bench, to the on-sky results in the extreme AO regime, as of late 2016/early 2017. To this purpose, we also provide a few recent on-sky imaging examples, notably high-contrast ADI detection of the planetary-mass companion \kappa Andromedae b, with a signal-to-noise ratio above 100 reached in less than 10 mn exposure time.

Adaptive optic (AO) systems delivering high levels of wavefront correction are now common at observatories. One of the main limitations to image quality after wavefront correction comes from atmospheric refraction. An Atmospheric dispersion compensator (ADC) is employed to correct for atmospheric refraction. The correction is applied based on a look-up table consisting of dispersion values as a function of telescope elevation angle. The look-up table based correction of atmospheric dispersion results in imperfect compensation leading to the presence of residual dispersion in the point-spread function (PSF) and is insufficient when sub-milliarcsecond precision is required. The presence of residual dispersion can limit the achievable contrast while employing high-performance coronagraphs or can compromise high-precision astrometric measurements. In this paper, we present the first on-sky closed-loop correction of atmospheric dispersion by directly using science path images. The concept behind the measurement of dispersion utilizes the chromatic scaling of focal plane speckles. An adaptive speckle grid generated with a deformable mirror (DM) that has a sufficiently large number of actuators is used to accurately measure the residual dispersion and subsequently correct it by driving the ADC. We have demonstrated with the Subaru Coronagraphic Extreme AO (SCExAO) system on-sky closed-loop correction of residual dispersion to < 1 mas across H-band. This work will aid in the direct detection of habitable exoplanets with upcoming extremely large telescopes (ELTs) and also provide a diagnostic tool to test the performance of instruments which require sub-milliarcsecond correction.

The EXoplanetary Circumstellar Environments and Disk Explorer (EXCEDE) science mission concept uses a visible-wavelength Phase-Induced Amplitude Apodization (PIAA) coronagraph to enable high-contrast imaging of circumstellar debris systems and some giant planets at angular separations reaching into the habitable zones of some of the nearest stars. We report on the experimental results obtained in the vacuum chamber at the Lockheed Martin Advanced Technology Center in 10% broadband light centered about 650 nm, with a median contrast of $1 \times 10^{-5}$ between 1.2 and 2.0 $\lambda$/D simultaneously with $3 \times 10^{-7}$ contrast between 2 and 11 $\lambda/D$ for a single-sided dark hole using a deformable mirror (DM) upstream of the PIAA coronagraph. These results are stable and repeatable as demonstrated by three measurements runs with DM settings set from scratch and maintained on the best 90% out of the 1000 collected frames. We compare the reduced experimental data with simulation results from modeling observed experimental limits; observed performance is consistent with uncorrected low-order modes not estimated by the Low Order Wavefront Sensor (LOWFS). Modeled sensitivity to bandwidth and residual tip/tilt modes is well-matched to the experiment.

Photonic technologies offer numerous advantages for astronomical instruments such as spectrographs and interferometers owing to their small footprints and diverse range of functionalities. Operating at the diffraction-limit, it is notoriously difficult to efficiently couple such devices directly with large telescopes. We demonstrate that with careful control of both the non-ideal pupil geometry of a telescope and residual wavefront errors, efficient coupling with single-mode devices can indeed be realised. A fibre injection was built within the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument. Light was coupled into a single-mode fibre operating in the near-IR (J-H bands) which was downstream of the extreme adaptive optics system and the pupil apodising optics. A coupling efficiency of 86% of the theoretical maximum limit was achieved at 1550 nm for a diffraction-limited beam in the laboratory, and was linearly correlated with Strehl ratio. The coupling efficiency was constant to within <30% in the range 1250-1600 nm. Preliminary on-sky data with a Strehl ratio of 60% in the H-band produced a coupling efficiency into a single-mode fibre of ~50%, consistent with expectations. The coupling was >40% for 84% of the time and >50% for 41% of the time. The laboratory results allow us to forecast that extreme adaptive optics levels of correction (Strehl ratio >90% in H-band) would allow coupling of >67% (of the order of coupling to multimode fibres currently). For Strehl ratios <20%, few-port photonic lanterns become a superior choice but the signal-to-noise must be considered. These results illustrate a clear path to efficient on-sky coupling into a single-mode fibre, which could be used to realise modal-noise-free radial velocity machines, very-long-baseline optical/near-IR interferometers and/or simply exploit photonic technologies in future instrument design.

We demonstrate for the first time an efficient, photonic-based astronomical spectrograph on the 8-m Subaru Telescope. An extreme adaptive optics system is combined with pupil apodiziation optics to efficiently inject light directly into a single-mode fiber, which feeds a compact cross-dispersed spectrograph based on array waveguide grating technology. The instrument currently offers a throughput of 5% from sky-to-detector which we outline could easily be upgraded to ~13% (assuming a coupling efficiency of 50%). The isolated spectrograph throughput from the single-mode fiber to detector was 42% at 1550 nm. The coupling efficiency into the single-mode fiber was limited by the achievable Strehl ratio on a given night. A coupling efficiency of 47% has been achieved with ~60% Strehl ratio on-sky to date. Improvements to the adaptive optics system will enable 90% Strehl ratio and a coupling of up to 67% eventually. This work demonstrates that the unique combination of advanced technologies enables the realization of a compact and highly efficient spectrograph, setting a precedent for future instrument design on very-large and extremely-large telescopes.

We present $H$-band scattered light imaging of a bright debris disk around the A0 star HD 36546 obtained from the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system with data recorded by the HiCIAO camera using the vector vortex coronagraph. SCExAO traces the disk from $r$ $\sim$ 0.3" to $r$ $\sim$ 1" (34--114 au). The disk is oriented in a near east-west direction (PA $\sim$ 75$^{o}$), is inclined by $i$ $\sim$ 70--75$^{o}$ and is strongly forward-scattering ($g$ $>$ 0.5). It is an extended disk rather than a sharp ring; a second, diffuse dust population extends from the disk's eastern side. While HD 36546 intrinsic properties are consistent with a wide age range ($t$ $\sim$ 1--250 $Myr$), its kinematics and analysis of coeval stars suggest a young age (3--10 $Myr$) and a possible connection to Taurus-Auriga's star formation history. SCExAO's planet-to-star contrast ratios are comparable to the first-light Gemini Planet Imager contrasts; for an age of 10 $Myr$, we rule out planets with masses comparable to HR 8799 b beyond a projected separation of 23 au. A massive icy planetesimal disk or an unseen superjovian planet at $r$ $>$ 20 au may explain the disk's visibility. The HD 36546 debris disk may be the youngest debris disk yet imaged, is the first newly-identified object from the now-operational SCExAO extreme AO system, is ideally suited for spectroscopic follow up with SCExAO/CHARIS in 2017, and may be a key probe of icy planet formation and planet-disk interactions.

We present high signal-to-noise ratio, precise $YJH$ photometry and $Y$ band (\gpiwave~$\mu$m) spectroscopy of HD 1160 B, a young substellar companion discovered from the Gemini NICI Planet Finding Campaign, using the Subaru Coronagraphic Extreme Adaptive Optics instrument and the Gemini Planet Imager. HD 1160 B has typical mid-M dwarf-like infrared colors and a spectral type of M5.5$^{+1.0}_{-0.5}$, where the blue edge of our $Y$ band spectrum rules out earlier spectral types. Atmospheric modeling suggests HD 1160 B having an effective temperature of 3000--3100 $K$, a surface gravity of log $g$ = 4--4.5, a radius of~\bestfitradius~$R_{\rm J}$, and a luminosity of log $L$/$L_{\odot} = -2.76 \pm 0.05$. Neither the primary's Hertzspring-Russell diagram position nor atmospheric modeling of HD 1160 B show evidence for a sub-solar metallicity. The interpretation of the HD 1160 B depends on which stellar system components are used to estimate an age. Considering HD 1160 A, B and C jointly, we derive an age of 80--125 Myr, implying that HD 1160 B straddles the hydrogen-burning limit (70--90 $M_{\rm J}$). If we consider HD 1160 A alone, younger ages (20--125 Myr) and a brown dwarf-like mass (35--90 $M_{\rm J}$) are possible. Interferometric measurements of the primary, a precise GAIA parallax, and moderate resolution spectroscopy can better constrain the system's age and how HD 1160 B fits within the context of (sub)stellar evolution.

Direct detection and spectroscopy of exoplanets requires high contrast imaging. For habitable exoplanets in particular, located at small angular separation from the host star, it is crucial to employ small inner working angle (IWA) coronagraphs that efficiently suppress starlight. These coronagraphs, in turn, require careful control of the wavefront which directly impacts their performance. For ground-based telescopes, atmospheric refraction is also an important factor, since it results in a smearing of the PSF, that can no longer be efficiently suppressed by the coronagraph. Traditionally, atmospheric refraction is compensated for by an atmospheric dispersion compensator (ADC). ADC control relies on an a priori model of the atmosphere whose parameters are solely based on the pointing of the telescope, which can result in imperfect compensation. For a high contrast instrument like the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system, which employs very small IWA coronagraphs, refraction-induced smearing of the PSF has to be less than 1 mas in the science band for optimum performance. In this paper, we present the first on-sky measurement and correction of residual atmospheric dispersion. Atmospheric dispersion is measured from the science image directly, using an adaptive grid of artificially introduced speckles as a diagnostic to feedback to the telescope's ADC. With our current setup, we were able to reduce the initial residual atmospheric dispersion from 18.8 mas to 4.2 in broadband light (y- to H-band), and to 1.4 mas in H-band only. This work is particularly relevant to the upcoming extremely large telescopes (ELTs) that will require fine control of their ADC to reach their full high contrast imaging potential.

We present new radial velocity measurements of eight stars secured with the spectrograph SOPHIE at the 193-cm telescope of the Haute-Provence Observatory allowing the detection and characterization of new giant extrasolar planets. The host stars are dwarfs of spectral types between F5 and K0 and magnitudes between 6.7 and 9.6; the planets have minimum masses M_p sin i between 0.4 to 3.8 M_Jup and orbital periods of several days to several months. The data allow only single planets to be discovered around the first six stars (HD143105, HIP109600, HD35759, HIP109384, HD220842, and HD12484), but one of them shows the signature of an additional substellar companion in the system. The seventh star, HIP65407, allows the discovery of two giant planets, just outside the 12:5 resonance in weak mutual interaction. The last star, HD141399, was already known to host a four-planetary system; our additional data and analyses allow new constraints to be put on it. We present Keplerian orbits of all systems, together with dynamical analyses of the two multi-planetary systems. HD143105 is one of the brightest stars known to host a hot Jupiter, which could allow numerous follow-up studies to be conducted despite this is not a transiting system. The giant planets HIP109600b, HIP109384b, and HD141399c are located in the habitable zone of their host star.

The scientific interest in directly image and identifying Earth-like planets within the Habitable Zone (HZ) around nearby stars is driving the design of specialized direct imaging mission such as ACESAT, EXO-C, EXO-S and AFTA-C. The inner edge of Alpha Cen A and B Habitable Zone is found at exceptionally large angular separations of 0.7 and 0.4 arcseconds respectively. This enables direct imaging of the system with a 0.3m class telescope. Contrast ratios in the order of 1e-10 are needed to image Earth-brightness planets. Low-resolution (5-band) spectra of all planets, will allow establishing the presence and amount of an atmosphere. This star system configuration is optimal for a specialized small, and stable space telescope, that can achieve high-contrast but has limited resolution. This paper describes an innovative instrument design and a mission concept based on a full Silicon Carbide off-axis telescope, which has a Phase Induce Amplitude Apodization coronagraph embedded in the telescope. This architecture maximizes stability and throughput. A Multi-Star Wave Front algorithm is implemented to drive a deformable mirror controlling simultaneously diffracted light from the on-axis and binary companion star. The instrument has a Focal Plane Occulter to reject starlight into a high-precision pointing control camera. Finally we utilize a Orbital Differential Imaging (ODI) post-processing method that takes advantage of a highly stable environment (Earth-trailing orbit) and a continuous sequence of images spanning 2 years, to reduce the final noise floor in post processing to 2e-11 levels, enabling high confidence and at least 90 percent completeness detections of Earth-like planets.

Several mission concepts are being studied to directly image planets around nearby stars. It is commonly thought that directly imaging a potentially habitable exoplanet around a Sun-like star requires space telescopes with apertures of at least 1m. A notable exception to this is Alpha Centauri (A and B), which is an extreme outlier among FGKM stars in terms of apparent habitable zone size: the habitable zones are ~3x wider in apparent size than around any other FGKM star. This enables a ~30-45cm visible light space telescope equipped with a modern high performance coronagraph or starshade to resolve the habitable zone at high contrast and directly image any potentially habitable planet that may exist in the system. We presents a brief analysis of the astrophysical and technical challenges involved with direct imaging of Alpha Centauri with a small telescope and describe two new technologies that address some of the key technical challenges. In particular, the raw contrast requirements for such an instrument can be relaxed to 1e-8 if the mission spends 2 years collecting tens of thousands of images on the same target, enabling a factor of 500-1000 speckle suppression in post processing using a new technique called Orbital Difference Imaging (ODI). The raw light leak from both stars is controllable with a special wavefront control algorithm known as Multi-Star Wavefront Control (MSWC), which independently suppresses diffraction and aberrations from both stars using independent modes on the deformable mirror. We also show an example of a small coronagraphic mission concept to take advantage of this opportunity.

The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument is a multipurpose high-contrast imaging platform designed for the discovery and detailed characterization of exoplanetary systems and serves as a testbed for high-contrast imaging technologies for ELTs. It is a multi-band instrument which makes use of light from 600 to 2500nm allowing for coronagraphic direct exoplanet imaging of the inner 3 lambda/D from the stellar host. Wavefront sensing and control are key to the operation of SCExAO. A partial correction of low-order modes is provided by Subaru's facility adaptive optics system with the final correction, including high-order modes, implemented downstream by a combination of a visible pyramid wavefront sensor and a 2000-element deformable mirror. The well corrected NIR (y-K bands) wavefronts can then be injected into any of the available coronagraphs, including but not limited to the phase induced amplitude apodization and the vector vortex coronagraphs, both of which offer an inner working angle as low as 1 lambda/D. Non-common path, low-order aberrations are sensed with a coronagraphic low-order wavefront sensor in the infrared (IR). Low noise, high frame rate, NIR detectors allow for active speckle nulling and coherent differential imaging, while the HAWAII 2RG detector in the HiCIAO imager and/or the CHARIS integral field spectrograph (from mid 2016) can take deeper exposures and/or perform angular, spectral and polarimetric differential imaging. Science in the visible is provided by two interferometric modules: VAMPIRES and FIRST, which enable sub-diffraction limited imaging in the visible region with polarimetric and spectroscopic capabilities respectively. We describe the instrument in detail and present preliminary results both on-sky and in the laboratory.

The ability to characterize exoplanets by spectroscopy of their atmospheres requires direct imaging techniques to isolate planet signal from the bright stellar glare. One of the limitations with the direct detection of exoplanets, either with ground- or space-based coronagraphs, is pointing errors and other low-order wavefront aberrations. The coronagraphic detection sensitivity at the diffraction limit therefore depends on how well low-order aberrations upstream of the focal plane mask are corrected. To prevent starlight leakage at the inner working angle of a phase mask coronagraph, we have introduced a Lyot-based low-order wavefront sensor (LLOWFS), which senses aberrations using the rejected starlight diffracted at the Lyot plane. In this paper, we present the implementation, testing and results of LLOWFS on the Subaru Coronagraphic Extreme Adaptive Optics system (SCExAO) at the Subaru Telescope. We have controlled thirty-five Zernike modes of a H-band vector vortex coronagraph in the laboratory and ten Zernike modes on sky with an integrator control law. We demonstrated a closed-loop pointing residual of 0.02 mas in the laboratory and 0.15 mas on sky for data sampled using the minimal 2-second exposure time of the science camera. We have also integrated the LLOWFS in the visible high-order control loop of SCExAO, which in closed-loop operation has validated the correction of the non-common path pointing errors between the infrared science channel and the visible wavefront sensing channel with pointing residual of 0.23 mas on sky.

The Large Binocular Telescope Interferometer is a NASA-funded nulling and imaging instrument designed to coherently combine the two 8.4-m primary mirrors of the LBT for high-sensitivity, high-contrast, and high-resolution infrared imaging (1.5-13 um). PHASECam is LBTI's near-infrared camera used to measure tip-tilt and phase variations between the two AO-corrected apertures and provide high-angular resolution observations. We report on the status of the system and describe its on-sky performance measured during the first semester of 2014. With a spatial resolution equivalent to that of a 22.8-meter telescope and the light-gathering power of single 11.8-meter mirror, the co-phased LBT can be considered to be a forerunner of the next-generation extremely large telescopes (ELT).

This paper is the third in the series on the technology development for the EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer) mission concept, which in 2011 was selected by NASA's Explorer program for technology development (Category III). EXCEDE is a 0.7m space telescope concept designed to achieve raw contrasts of 1e6 at an inner working angle of 1.2 l/D and 1e7 at 2 l/D and beyond. This will allow it to directly detect and spatially resolve low surface brightness circumstellar debris disks as well as image giant planets as close as in the habitable zones of their host stars. In addition to doing fundamental science on debris disks, EXCEDE will also serve as a technological and scientific precursor for any future exo-Earth imaging mission. EXCEDE uses a Starlight Suppression System (SSS) based on the PIAA coronagraph, enabling aggressive performance. We report on our continuing progress of developing the SSS for EXCEDE, and in particular (a) the reconfiguration of our system into a more flight-like layout, with an upstream deformable mirror and an inverse PIAA system, as well as a LOWFS, and (b) testing this system in a vacuum chamber, including IWA, contrast, and stability performance. The results achieved so far are 2.9e-7 contrast between 1.2-2.0 l/D and 9.7e-8 contrast between 2.0-6.0 l/D in monochromatic light; as well as 1.4e-6 between 2.0-6.0 l/D in a 10% band, all with a PIAA coronagraph operating at an inner working angle of 1.2 l/D. This constitutes better contrast than EXCEDE requirements (in those regions) in monochromatic light, and progress towards requirements in broadband light. Even though this technology development is primarily targeted towards EXCEDE, it is also germane to any exoplanet direct imaging space-based telescopes because of the many challenges common to different coronagraph architectures and mission requirements.

For the technology development of the mission EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer) - a 0.7 m telescope equipped with a Phase-Induced Amplitude Apodization Coronagraph (PIAA-C) and a 2000-element MEMS deformable mirror, capable of raw contrasts of 1e-6 at 1.2 lambda/D and 1e-7 above 2 lambda/D - we developed two test benches simulating its key components, one in air, the other in vacuum. To achieve this level of contrast, one of the main goals is to remove low-order aberrations, using a Low-Order WaveFront Sensor (LOWFS). We tested this key component, together with the coronagraph and the wavefront control, in air at NASA Ames Research Center and in vacuum at Lockheed Martin. The LOWFS, controlling tip/tilt modes in real time at 1~kHz, allowed us to reduce the disturbances in air to 1e-3 lambda/D rms, letting us achieve a contrast of 2.8e-7 between 1.2 and 2 lambda/D. Tests are currently being performed to achieve the same or a better level of correction in vacuum. With those results, and by comparing them to simulations, we are able to deduce its performances on different coronagraphs - different sizes of telescopes, inner working angles, contrasts, etc. - and therefore study its contribution beyond EXCEDE.

High-contrast imaging will be a challenge for future ELTs, because their vibrations create low-order aberrations - mostly tip/tilt - that reduce coronagraphic performances at 1.2 lambda/D and above. A Low-Order WaveFront Sensor (LOWFS) is essential to measure and control those aberrations. An experiment simulating a starlight suppression system is currently developed at NASA Ames Research Center, and includes a LOWFS controlling tip/tilt modes in real-time at 500 Hz. The LOWFS allowed us to reduce the tip/tilt disturbances to 1e-3 lambda/D rms, enhancing the previous contrast by a decade, to 8e-7 between 1.2 and 2 lambda/D. A Linear Quadratic Gaussian (LQG) controller is currently implemented to improve even more that result by reducing residual vibrations. This testbed is developed for the mission EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer), selected by NASA for technology development, and designed to study the formation, evolution and architectures of exoplanetary systems and characterize circumstellar environments into stellar habitable zones. It is composed of a 0.7 m telescope equipped with a Phase-Induced Amplitude Apodization Coronagraph (PIAA-C) and a 2000-element MEMS deformable mirror, capable of raw contrasts of 1e-6 at 1.2 lambda/D and 1e-7 above 2 lambda/D. Although the testbed simulates space conditions, its LOWFS has the same design than on the SCExAO instrument at Subaru telescope, with whom it shares the same kind of problematic. Experimental results show that a good knowledge of the low-order disturbances is a key asset for high contrast imaging, whether for real-time control or for post processing, both in space and on ground telescopes.

The mission EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer), selected by NASA for technology development, is designed to study the formation, evolution and architectures of exoplanetary systems and characterize circumstellar environments into stellar habitable zones. It is composed of a 0.7 m telescope equipped with a Phase-Induced Amplitude Apodization Coronagraph (PIAA-C) and a 2000-element MEMS deformable mirror, capable of raw contrasts of 1e-6 at 1.2 lambda/D and 1e-7 above 2 lambda/D. One of the key challenges to achieve those contrasts is to remove low-order aberrations, using a Low-Order WaveFront Sensor (LOWFS). An experiment simulating the starlight suppression system is currently developed at NASA Ames Research Center, and includes a LOWFS controlling tip/tilt modes in real time at 500 Hz. The LOWFS allowed us to reduce the tip/tilt disturbances to 1e-3 lambda/D rms, enhancing the previous contrast by a decade, to 8e-7 between 1.2 and 2 lambda/D. A Linear Quadratic Gaussian (LQG) controller is currently implemented to improve even more that result by reducing residual vibrations. This testbed shows that a good knowledge of the low-order disturbances is a key asset for high contrast imaging, whether for real-time control or for post processing.

Nowadays, astronomers want to observe gaps in exozodiacal disks to confirm the presence of exoplanets, or even make actual images of these companions. Four hundred and fifty years ago, Jean-Dominique Cassini did a similar study on a closer object: Saturn. After joining the newly created Observatoire de Paris in 1671, he discovered 4 of Saturn's satellites (Iapetus, Rhea, Tethys and Dione), and also the gap in its rings. He made these discoveries observing through the best optics at the time, made in Italy by famous opticians like Giuseppe Campani or Eustachio Divini. But was he really able to observe this black line in Saturn's rings? That is what a team of optical scientists from Observatoire de Paris - LESIA with the help of Onera and Institut d'Optique tried to find out, analyzing the lenses used by Cassini, and still preserved in the collection of the observatory. The main difficulty was that even if the lenses have diameters between 84 and 239 mm, the focal lengths are between 6 and 50 m, more than the focal lengths of the primary mirrors of future ELTs. The analysis shows that the lenses have an exceptionally good quality, with a wavefront error of approximately 50 nm rms and 200 nm peak-to-valley, leading to Strehl ratios higher than 0.8. Taking into account the chromaticity of the glass, the wavefront quality and atmospheric turbulence, reconstructions of his observations tend to show that he was actually able to see the division named after him.

Stabilizing a nulling interferometer at a nanometric level is the key issue to obtain deep null depths. The PERSEE breadboard has been designed to study and optimize the operation of a cophased nulling bench in the most realistic disturbing environment of a space mission. This presentation focuses on the current results of the PERSEE bench. In terms of metrology, we cophased at 0.33 nm rms for the piston and 80 mas rms for the tip/tilt (0.14% of the Airy disk). A Linear Quadratic Gaussian (LQG) control coupled with an unsupervised vibration identification allows us to maintain that level of correction, even with characteristic vibrations of nulling interferometry space missions. These performances, with an accurate design and alignment of the bench, currently lead to a polychromatic unpolarised null depth of 8.9E-6 stabilized at 3E-7 on the [1.65-2.45] \mum spectral band (37% bandwidth).

Nulling interferometry is still a promising method to characterize spectra of exoplanets. One of the main issues is to cophase at a nanometric level each arm despite satellite disturbances. The bench PERSEE aims to prove the feasibility of that technique for spaceborne missions. After a short description of PERSEE, we will first present the results obtained in a simplified configuration: we have cophased down to 0.22 nm rms in optical path difference (OPD) and 60 mas rms in tip/tilt, and have obtained a monochromatic null of 3E-5 stabilized at 3E-6. The goal of 1 nm with additional typical satellite disturbances requires the use of an optimal control law; that is why we elaborated a dedicated Kalman filter. Simulations and experiments show a good rejection of disturbances. Performance of the bench should be enhanced by using a Kalman control law, and we should be able to reach the desired nanometric stability. Following, we will present the first results of the final polychromatic configuration, which includes an achromatic phase shifter, perturbators and optical delay lines. As a conclusion, we give the first more general lessons we have already learned from this experiment, both at system and component levels for a future space mission.

High contrast coronagraphic imaging is challenging for telescopes with central obstructions and thick spider vanes, such as the Subaru Telescope. We present in this paper the first laboratory demonstration of a high efficiency PIAA-type coronagraph on such a pupil, using coronagraphic optics which will be part of the Subaru Coronagraphic Extreme-AO (SCExAO) system currently under assembly. Lossless pupil apodization is performed by a set of aspheric PIAA lenses specifically designed to also remove the pupil's central obstruction, coupled with a Spider Removal Plate (SRP) which removes spider vanes by translating four parts of the pupil with tilted plane-parallel plates. An "inverse-PIAA" system, located after the coronagraphic focal plane mask, is used to remove off-axis aberrations and deliver a wide field of view. Our results validate the concept adopted for the SCExAO system, and show that the Subaru Telescope pupil can properly be apodized for high contrast coronagraphic imaging as close as $\approx$ 1 $\lambda/D$ with no loss of sensitivity. We also verify that off-axis aberrations in the system are in agreement with theory, and that the inverse PIAA system recovers a wide usable field of view for exoplanet detection and disks imaging.

High contrast coronagraphic imaging is a challenging task for telescopes with central obscurations and thick spider vanes, such as the Subaru Telescope. Our group is currently assembling an extreme AO bench designed as an upgrade for the newly commissionned coronagraphic imager instrument HiCIAO, that addresses these difficulties. The so-called SCExAO system combines a high performance PIAA coronagraph to a MEMS-based wavefront control system that will be used in complement of the Subaru AO188 system. We present and demonstrate good performance of two key optical components that suppress the spider vanes, the central obscuration and apodize the beam for high contrast coronagraphy, while preserving the throughput and the angular resolution.