We develop an original apparatus of the granular impact experiment by which the incident angle of the solid projectile and inclination angle of the target granular layer can be systematically varied. Whereas most of the natural cratering events occur on inclined surfaces with various incident angles, there have not been any experiments on oblique impacts on an inclined target surface. To perform systematic impact experiments, a novel experimental apparatus has to be developed. Therefore, we build an apparatus for impact experiments where both the incident angle and the inclination angle can be independently varied. The projectile-injection unit accelerates a plastic ball (6~mm in diameter) up to $v_i\simeq 100$~m~s$^{-1}$ impact velocity. The barrel of the injection unit is made with a three-dimensional printer. The impact dynamics is captured by high-speed cameras to directly measure the impact velocity and incident angle. The rebound dynamics of the projectile (restitution coefficient and rebound angle) is also measured. The final crater shapes are measured using a line-laser profiler mounted on the electric stages. By scanning the surface using this system, a three-dimensional crater shape (height map) can be constructed. From the measured result, we can define and measure the characteristic quantities of the crater. The analyzed result on the restitution dynamics is presented as an example of systematic experiments using the developed system.

Although a large number of astronomical craters are actually produced by the oblique impacts onto inclined surfaces, most of the laboratory experiments mimicking the impact cratering have been performed by the vertical impact onto a horizontal target surface. In previous studies on the effects of oblique impact and inclined terrain, only one of the impact angle $\varphi$ or target inclination angle $\theta$ has been varied in the experiments. Therefore, we perform impact-cratering experiments by systematically varying both $\varphi$ and $\theta$. A solid projectile of diameter $D_{\rm i}=6$~mm is impacted onto a sand surface with the range of impact velocity $v_{\rm i}=7$--$97$~m~s$^{-1}$. From the experimental result, we develop scaling laws for the crater dimensions on the basis of $\Pi$-group scaling. As a result, the crater dimensions such as cavity volume, diameter, aspect ratio, and depth-diameter ratio can be scaled by the factors $\sin \varphi$ and $\cos \theta$ as well as the usual impact parameters ($v_{\rm i}$, $D_{\rm i}$, density of projectile, and surface gravity). Finally, we consider the possible application of the obtained scaling laws to the estimate of impact conditions (e.g., impact speed and impact angle) in natural crater records.

The impact-induced energy transfer and dissipation in granular targets without any confining walls are studied by microgravity experiments. A solid projectile impacts into a granular target at low impact speed ($0.045 \leq v_p \leq 1.6$~m~s$^{-1}$) in a laboratory drop tower. Granular clusters consisting of soft or hard particles are used as targets. Porous dust agglomerates and glass beads are used for soft and hard particles, respectively. The expansion of the granular target cluster is recorded by a high-speed camera. Using the experimental data, we find that (i)~a simple energy scaling can explain the energy transfer in both, soft- and hard-particles granular targets, (ii)~the kinetic impact energy is isotropically transferred to the target from the impact point, and (iii)~the transferred kinetic energy is $2$~-~$7$\% of the projectile's initial kinetic energy. The dissipative-diffusion model of energy transfer can quantitatively explain these behaviors.

Dynamic characterization of mechanical properties of dust aggregates has been one of the most important problems to quantitatively discuss the dust growth in protoplanetary disks. We experimentally investigate the dynamic properties of dust aggregates by low-speed ($\lesssim 3.2$ m s$^{-1}$) impacts of solid projectiles. Spherical impactors made of glass, steel, or lead are dropped onto a dust aggregate of packing fraction $\phi=0.35$ under vacuum conditions. The impact results in cratering or fragmentation of the dust aggregate, depending on the impact energy. The crater shape can be approximated by a spherical segment and no ejecta are observed. To understand the underlying physics of impacts into dust aggregates, the motion of the solid projectile is acquired by a high-speed camera. Using the obtained position data of the impactor, we analyze the drag-force law and dynamic pressure induced by the impact. We find that there are two characteristic strengths. One is defined by the ratio between impact energy and crater volume and is $\simeq 120$ kPa. The other strength indicates the fragmentation threshold of dynamic pressure and is $\simeq 10$ kPa. The former characterizes the apparent plastic deformation and is consistent with the drag force responsible for impactor deceleration. The latter corresponds to the dynamic tensile strength to create cracks. Using these results, a simple model for the compaction and fragmentation threshold of dust aggregates is proposed. In addition, the comparison of drag-force laws for dust aggregates and loose granular matter reveals the similarities and differences between the two materials.

A model for the asteroid resurfacing by regolith convection is built to estimate its timescale. In the model, regolith convection is driven by the impact-induced global seismic shaking. The model consists of three steps: (i) intermittent impact of meteoroids, (ii) impact-induced global vibration (seismic shaking), and (iii) vibration-induced regolith convection. In order to assess the feasibility of the resurfacing process driven by regolith convection, we estimate the resurfacing timescale as a function of the size of a target asteroid. In the estimate, a set of parameter values is assumed on the basis of previous works. However, some of them (e.g., seismic quality factor $Q$, seismic efficiency $\eta$, and seismic frequency $f$) are very uncertain. Although these parameter values might depend on asteroid size, we employ the standard values to estimate the representative behavior. To clarify the parameter dependences, we develop an approximated scaling form for the resurfacing timescale. According to the estimated result, we find that the regolith-convection-based resurfacing timescale is shorter than the mean collisional lifetime in most of the parameter uncertainty ranges. These parameter ranges are within those reported by previous works for small asteroids. This means that the regolith convection can be a possible mechanism for the asteroid resurfacing process.