Any high-contrast imaging instrument in a future large space-based telescope will include an integral field spectrograph (IFS) for measuring broadband starlight residuals and characterizing the exoplanet's atmospheric spectrum. In this paper, we report the development of a high-contrast integral field spectrograph (HCIFS) at Princeton University and demonstrate its application in multi-spectral wavefront control. Moreover, we propose and experimentally validate a new reduced-dimensional system identification algorithm for an IFS imaging system, which improves the system's wavefront control speed, contrast and computational and data storage efficiency.

Space coronagraphs are projected to detect exoplantes that are at least 1e10 times dimmer than their host stars. Yet, the actual detection threshold depends on the instrument's wavefront stability and varies by an order of magnitude with the choice of observation strategy and post-processing method. In this paper the authors consider the performance of the previously introduced observation strategy (dark hole maintenance) and post-processing algorithm (electric field order reduction) in the presence of various realistic effects. In particular, it will be shown that under some common assumptions, the telescope's averaged pointing jitter translates into an additional light source incoherent with the residual light from the star (speckles), and that jitter "modes" can be identified in post-processing and distinguished from a planet signal. We also show that the decrease in contrast due to drift of voltages in deformable mirror actuators can be mitigated by recursive estimation of the electric field in the high-contrast region of the image (dark hole) using Electric Field Conjugation (EFC). Moreover, this can be done even when the measured intensity is broadband, as long as it is well approximated by an incoherent sum of monochromatic intensities. Finally, we assess the performance of closed-loop vs. open-loop observation scenarios through a numerical simulation of the Wide-Field Infra-Red Survey Telescope (WFIRST). In particular, we compare the post-processing factors of Angular Differential Imaging (ADI) with and without Electric Field Order Reduction (EFOR), which we extended to account for possible telescope rolls and the presence of pointing jitter. For all observation parameters considered in this paper, close-loop dark hole maintenance resulted in significantly higher post-processing accuracy.

Exoplanets are very dim. An Electron Multiplying Charged Coupled Device (EMCCD) operating in photon counting (PC) mode reduces the noise level and enables their detection. Typically, PC images are added together as a co-added image before processing. We present here a signal detection and estimation technique working directly with the PC images. The method is based on the generalized maximum likelihood ratio test (GLRT) and uses a binomial distribution between PC images. It can be applied online, so it is possible to stop observations once we have reached a threshold confidence for the existence (or absence) of planets, and thus the observation time is efficiently used. It directly uses the detector model, which more accurately represents its noise characteristics. We show that it outperforms our previous GLRT method using co-added images under Gaussian noise assumption.

Astrophysics spans an enormous range of questions on scales from individual planets to the entire cosmos. To address the richness of 21st century astrophysics requires a corresponding richness of telescopes spanning all bands and all messengers. Much scientific benefit comes from having the multi-wavelength capability available at the same time. Most of these bands,or measurement sensitivities, require space-based missions. Historically, NASA has addressed this need for breadth with a small number of flagship-class missions and a larger number of Explorer missions. While the Explorer program continues to flourish, there is a large gap between Explorers and strategic missions. A fortunate combination of new astrophysics technologies with new, high capacity, low dollar-per-kg to orbit launchers, and new satellite buses allow for cheaper missions with capabilities approaching strategic mission levels. NASA has recognized these developments by calling for Probe-class mission ideas for mission studies, spanning most of the electromagnetic spectrum from GeV gamma-rays to the far infrared, and the new messengers of neutrinos and ultra-high energy cosmic rays. The key insight from the Probes exercise is that order-of-magnitude advances in science performance metrics are possible across the board for initial total cost estimates in the range 500M-1B dollars.

Future large space telescopes will be equipped with adaptive optics (AO) to overcome wavefront aberrations and achieve high contrast for imaging faint astronomical objects, such as earth-like exoplanets and debris disks. In contrast to AO that is widely used in ground telescopes, space-based AO systems will use focal plane wavefront sensing to measure the wavefront aberrations. Focal plane wavefront sensing is a class of techniques that reconstruct the light field based on multiple focal plane images distorted by deformable mirror (DM) probing perturbations. In this paper, we report an efficient focal plane wavefront sensing approach for space-based AO which optimizes the DM probing perturbation and thus also the integration time for each image. Simulation of the AO system equipped with a vortex coronagraph has demonstrated that our new approach enables efficient information acquisition and significantly reduces the time needed for achieving high contrast in space.

We describe the current performance of the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument on the Subaru telescope on Maunakea, Hawaii and present early science results for SCExAO coupled with the CHARIS integral field spectrograph. SCExAO now delivers H band Strehl ratios up to $\sim$ 0.9 or better, extreme AO corrections for optically faint stars, and planet-to-star contrasts rivaling that of GPI and SPHERE. CHARIS yield high signal-to-noise detections and 1.1--2.4 $\mu m$ spectra of benchmark directly-imaged companions like HR 8799 cde and kappa And b that clarify their atmospheric properties. We also show how recently published as well as unpublished observations of LkCa 15 lead to a re-evaluation of its claimed protoplanets. Finally, we briefly describe plans for a SCExAO-focused direct imaging campaign to directly image and characterize young exoplanets, planet-forming disks, and (later) mature planets in reflected light.

In high-contrast space-based coronagraphs, one of the main limiting factors for imaging the dimmest exoplanets is the time varying nature of the residual starlight (speckles). Modern methods try to differentiate between the intensities of starlight and other sources, but none incorporate models of space-based systems which can take into account actuations of the deformable mirrors. Instead, we propose formulating the estimation problem in terms of the electric field while allowing for dithering of the deformable mirrors. Our reduced-order approach is similar to intensity-based PCA (e.g. KLIP) although, under certain assumptions, it requires a considerably lower number of modes of the electric field. We illustrate this by a FALCO simulation of the WFIRST hybrid Lyot coronagraph.

Two studies utilizing sparse aperture masking (SAM) interferometry and $H_{\rm \alpha}$ differential imaging have reported multiple jovian companions around the young solar-mass star, LkCa 15 (LkCa 15 bcd): the first claimed direct detection of infant, newly-formed planets ("protoplanets"). We present new near-infrared direct imaging/spectroscopy from the SCExAO system coupled with the CHARIS integral field spectrograph and multi-epoch thermal infrared imaging from Keck/NIRC2 of LkCa 15 at high Strehl ratios. These data provide the first direct imaging look at the same wavelengths and in the same locations where previous studies identified the LkCa 15 protoplanets and thus offer the first decisive test of their existence. The data do not reveal these planets. Instead, we resolve extended emission tracing a dust disk with a brightness and location comparable to that claimed for LkCa 15 bcd. Forward-models attributing this signal to orbiting planets are inconsistent with the combined SCExAO/CHARIS and Keck/NIRC2 data. An inner disk provides a more compelling explanation for the SAM detections and perhaps also the claimed $H_{\alpha}$ detection of LkCa 15 b. We conclude that there is currently no clear, direct evidence for multiple protoplanets orbiting LkCa 15, although the system likely contains at least one unseen jovian companion. To identify jovian companions around LkCa 15 from future observations, the inner disk should be detected and its effect modeled, removed, and shown to be distinguishable from planets. Protoplanet candidates identified from similar systems should likewise be clearly distinguished from disk emission through modeling.

Ground-based telescopes coupled with adaptive optics (AO) have been playing a leading role in exoplanet direct imaging science and technological development for the past two decades and will continue to have an indispensable role for the next decade and beyond. Over the next decade, extreme AO systems on 8-10m telescopes will 1) mitigate risk for WFIRST-CGI by identifying numerous planets the mission can spectrally characterize, 2) validate performance requirements and motivate improvements to atmosphere models needed to unambiguously characterize solar system-analogues from space, and 3) mature novel technological innovations useful for space. Extremely Large Telescopes can deliver the first thermal infrared (10 $\mu m$) images of rocky planets around Sun-like stars and identify biomarkers. These data provide a future NASA direct imaging flagship mission (i.e. HabEx, LUVOIR) with numerous exo-Earth candidates and critical ancillary information to help clarify whether these planets are habitable.

Direct exoplanet imaging via coronagraphy requires maintenance of high contrast in a dark hole for lengthy integration periods. Wavefront errors that change slowly over that time accumulate and cause systematic errors in the star's Point Spread Function (PSF) which limit the achievable signal-to-noise ratio of the planet. In this paper we show that estimating the speckle drift can be achieved via intensity measurements in the dark hole together with dithering of the deformable mirrors to increase phase diversity. A scheme based on an Extended Kalman Filter and Electric Field Conjugation is proposed for maintaining the dark hole during the integration phase. For the post-processing phase, an a posteriori approach is proposed to estimate the realization of the PSF drift process and the intensity of the planet light incoherent with the speckles.

The Wide Field Infrared Survey Telescope (WFIRST) Coronagraph Instrument (CGI) is a high-contrast imager and integral field spectrograph that will enable the study of exoplanets and circumstellar disks at visible wavelengths. Ground-based high-contrast instrumentation has fundamentally limited performance at small working angles, even under optimistic assumptions for 30m-class telescopes. There is a strong scientific driver for better performance, particularly at visible wavelengths. Future flagship mission concepts aim to image Earth analogues with visible light flux ratios of more than 10^10. CGI is a critical intermediate step toward that goal, with a predicted 10^8-9 flux ratio capability in the visible. CGI achieves this through improvements over current ground and space systems in several areas: (i) Hardware: space-qualified (TRL9) deformable mirrors, detectors, and coronagraphs, (ii) Algorithms: wavefront sensing and control; post-processing of integral field spectrograph, polarimetric, and extended object data, and (iii) Validation of telescope and instrument models at high accuracy and precision. This white paper, submitted to the 2018 NAS Exoplanet Science Strategy call, describes the status of key CGI technologies and presents ways in which performance is likely to evolve as the CGI design matures.

We present new, near-infrared (1.1--2.4 $\mu m$) high-contrast imaging of the bright debris disk surrounding HIP 79977 with the Subaru Coronagraphic Extreme Adaptive Optics system (SCExAO) coupled with the CHARIS integral field spectrograph. SCExAO/CHARIS resolves the disk down to smaller angular separations of (0.11"; $r \sim 14$ au) and at a higher significance than previously achieved at the same wavelengths. The disk exhibits a marginally significant east-west brightness asymmetry in $H$ band that requires confirmation. Geometrical modeling suggests a nearly edge-on disk viewed at a position angle of $\sim$ 114.6$^{o}$ east of north. The disk is best-fit by scattered-light models assuming strongly forward-scattering grains ($g$ $\sim$ 0.5--0.65) confined to a torus with a peak density at $r_{0}$ $\sim$ 53--75 au. We find that a shallow outer density power law of $\alpha_{out}=$-1-- -3 and flare index of $\beta = 1$ are preferred. Other disk parameters (e.g.~inner density power law and vertical scale height) are more poorly constrained. The disk has a slightly blue intrinsic color and its profile is broadly consistent with predictions from birth ring models applied to other debris disks. While HIP 79977's disk appears to be more strongly forward-scattering than most resolved disks surrounding 5--30 Myr-old stars, this difference may be due to observational biases favoring forward-scattering models for inclined disks vs. lower inclination, ostensibly neutral-scattering disks like HR 4796A's. Deeper, higher signal-to-noise SCExAO/CHARIS data can better constrain the disk's dust composition.

We present SCExAO/CHARIS high-contrast imaging/$JHK$ integral field spectroscopy of $\kappa$ And b, a directly-imaged low-mass companion orbiting a nearby B9V star. We detect $\kappa$ And b at a high signal-to-noise and extract high precision spectrophotometry using a new forward-modeling algorithm for (A-)LOCI complementary to KLIP-FM developed by Pueyo (2016). $\kappa$ And b's spectrum best resembles that of a low-gravity L0--L1 dwarf (L0--L1$\gamma$). Its spectrum and luminosity are very well matched by 2MASSJ0141-4633 and several other 12.5--15 $M_{\rm J}$ free floating members of the 40 $Myr$-old Tuc-Hor Association, consistent with a system age derived from recent interferometric results for the primary, a companion mass at/near the deuterium-burning limit (13$^{+12}_{-2}$ M$_{\rm J}$), and a companion-to-primary mass ratio characteristic of other directly-imaged planets ($q$ $\sim$ 0.005$^{+0.005}_{-0.001}$). We did not unambiguously identify additional, more closely-orbiting companions brighter and more massive than $\kappa$ And b down to $\rho$ $\sim$ 0.3" (15 au). SCExAO/CHARIS and complementary Keck/NIRC2 astrometric points reveal clockwise orbital motion. Modeling points towards a likely eccentric orbit: a subset of acceptable orbits include those that are aligned with the star's rotation axis. However, $\kappa$ And b's semimajor axis is plausibly larger than 75 au and in a region where disk instability could form massive companions. Deeper $\kappa$ And high-contrast imaging and low-resolution spectroscopy from extreme AO systems like SCExAO/CHARIS and higher resolution spectroscopy from Keck/OSIRIS or, later, IRIS on the Thirty Meter Telescope could help clarify $\kappa$ And b's chemistry and whether its spectrum provides an insight into its formation environment.

All coronagraphic instruments for exoplanet high-contrast imaging need wavefront correction systems to reject optical aberrations and create sufficiently dark holes. Since the most efficient wavefront correction algorithms (controllers and estimators) are usually model-based, the modeling accuracy of the system influences the ultimate wavefront correction performance. Currently, wavefront correction systems are typically approximated as linear systems using Fourier optics. However, the Fourier optics model is usually biased due to inaccuracies in the layout measurements, the imperfect diagnoses of inherent optical aberrations, and a lack of knowledge of the deformable mirrors (actuator gains and influence functions). Moreover, the telescope optical system varies over time because of instrument instabilities and environmental effects. In this paper, we present an expectation-maximization (E-M) approach for identifying and real-time adapting the linear telescope model from data. By iterating between the E-step (a Kalman filter and a Rauch smoother) and the M-step (analytical or gradient-based optimization), the algorithm is able to recover the system even if the model depends on the electric fields, which are unmeasurable hidden variables. Simulations and experiments in Princeton's High Contrast Imaging Lab demonstrate that this algorithm improves the model accuracy and increases the efficiency and speed of the wavefront correction.

The coronagraphic instrument (CGI) on the Wide-Field Infrared Survey Telescope (WFIRST) will demonstrate technologies and methods for high-contrast direct imaging and spectroscopy of exoplanet systems in reflected light, including polarimetry of circumstellar disks. The WFIRST management and CGI engineering and science investigation teams have developed requirements for the instrument, motivated by the objectives and technology development needs of potential future flagship exoplanet characterization missions such as the NASA Habitable Exoplanet Imaging Mission (HabEx) and the Large UV/Optical/IR Surveyor (LUVOIR). The requirements have been refined to support recommendations from the WFIRST Independent External Technical/Management/Cost Review (WIETR) that the WFIRST CGI be classified as a technology demonstration instrument instead of a science instrument. This paper provides a description of how the CGI requirements flow from the top of the overall WFIRST mission structure through the Level 2 requirements, where the focus here is on capturing the detailed context and rationales for the CGI Level 2 requirements. The WFIRST requirements flow starts with the top Program Level Requirements Appendix (PLRA), which contains both high-level mission objectives as well as the CGI-specific baseline technical and data requirements (BTR and BDR, respectively)... We also present the process and collaborative tools used in the L2 requirements development and management, including the collection and organization of science inputs, an open-source approach to managing the requirements database, and automating documentation. The tools created for the CGI L2 requirements have the potential to improve the design and planning of other projects, streamlining requirement management and maintenance. [Abstract Abbreviated]

The Wide Field Infrared Survey Telescope (WFIRST) was the top ranked large space mission in the 2010 New Worlds, New Horizons decadal survey, and it was formed by merging the science programs of 3 different mission concepts, including the Microlensing Planet Finder (MPF) concept (Bennett \etal\ 2010). The WFIRST science program (Spergel \etal\ 2015) consists of a general observer program, a wavefront controlled technology program, and two targeted science programs: a program to study dark energy, and a statistical census of exoplanets with a microlensing survey, which uses nearly one quarter of WFIRST's observing time in the current design reference mission. The New Worlds, New Horizons (decadal survey) midterm assessment summarizes the science case for the WFIRST exoplanet microlensing survey with this statement: "WFIRST's microlensing census of planets beyond 1 AU will perfectly complement Kepler's census of compact systems, and WFIRST will also be able to detect free-floating planets unbound from their parent stars\rlap."

Ground-based telescopes have been playing a leading role in exoplanet direct imaging science and technological development for the past two decades and will continue to have an indispensable role for the next decade and beyond. Extreme adaptive optics (AO) systems will advance focal-plane wavefront control and coronagraphy, augmenting the performance of and mitigating risk for WFIRST-CGI, while validating performance requirements and motivating improvements to atmosphere models needed to unambiguously characterize solar system-analogues with HabEx/LUVOIR. Specialized instruments for Extremely Large Telescopes may deliver the first thermal infrared images of rocky planets around Sun-like stars, providing HabEx/LUVOIR with numerous exo-Earth candidates and key ancillary information that can help clarify whether the planets are habitable.

We present early laboratory simulations and extensive on-sky tests validating of the performance of a shaped pupil coronagraph (SPC) behind an extreme-AO corrected beam of the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system. In tests with the SCExAO internal source/wavefront error simulator, the normalized intensity profile for the SPC degrades more slowly than for the Lyot coronagraph as low-order aberrations reduce the Strehl ratio from extremely high values (S.R. $\sim$ 0.93--0.99) to those characteristic of current ground-based extreme AO systems (S.R. $\sim$ 0.74--0.93) and then slightly lower values down to S.R. $\sim$ 0.57. On-sky SCExAO data taken with the SPC and other coronagraphs for brown dwarf/planet-hosting stars HD 1160 and HR 8799 provide further evidence for the SPC's robustness to low-order aberrations. From H-band Strehl ratios of 80% to 70%, the Lyot coronagraph's performance vs. that of the SPC may degrade even faster on sky than is seen in our internal source simulations. The 5-$\sigma$ contrast also degrades faster (by a factor of two) for the Lyot than the SPC. The SPC we use was designed as a technology demonstrator only, with a contrast floor, throughput, and outer working angle poorly matched for SCExAO's current AO performance and poorly tuned for imaging the HR 8799 planets. Nevertheless, we detect HR 8799 cde with SCExAO/CHARIS using the SPC in broadband mode, where the S/N for planet e is within 30% of that obtained using the vortex coronagraph. The shaped-pupil coronagraph is a promising design demonstrated to be robust in the presence of low-order aberrations and may be well-suited for future ground and space-based direct imaging observations, especially those focused on follow-up exoplanet characterization and technology demonstration of deep contrast within well-defined regions of the image plane.

We present the data reduction pipeline for CHARIS, a high-contrast integral-field spectrograph for the Subaru Telescope. The pipeline constructs a ramp from the raw reads using the measured nonlinear pixel response, and reconstructs the data cube using one of three extraction algorithms: aperture photometry, optimal extraction, or $\chi^2$ fitting. We measure and apply both a detector flatfield and a lenslet flatfield and reconstruct the wavelength- and position-dependent lenslet point-spread function (PSF) from images taken with a tunable laser. We use these measured PSFs to implement a $\chi^2$-based extraction of the data cube, with typical residuals of ~5% due to imperfect models of the undersampled lenslet PSFs. The full two-dimensional residual of the $\chi^2$ extraction allows us to model and remove correlated read noise, dramatically improving CHARIS' performance. The $\chi^2$ extraction produces a data cube that has been deconvolved with the line-spread function, and never performs any interpolations of either the data or the individual lenslet spectra. The extracted data cube also includes uncertainties for each spatial and spectral measurement. CHARIS' software is parallelized, written in Python and Cython, and freely available on github with a separate documentation page. Astrometric and spectrophotometric calibrations of the data cubes and PSF subtraction will be treated in a forthcoming paper.

For imaging faint exoplanets and disks, a coronagraph-equipped observatory needs focal plane wavefront correction to recover high contrast. The most efficient correction methods iteratively estimate the stellar electric field and suppress it with active optics. The estimation requires several images from the science camera per iteration. To maximize the science yield, it is desirable both to have fast wavefront correction and to utilize all the correction images for science target detection. Exoplanets and disks are incoherent with their stars, so a nonlinear estimator is required to estimate both the incoherent intensity and the stellar electric field. Such techniques assume a high level of stability found only on space-based observatories and possibly ground-based telescopes with extreme adaptive optics. In this paper, we implement a nonlinear estimator, the iterated extended Kalman filter (IEKF), to enable fast wavefront correction and a recursive, nearly-optimal estimate of the incoherent light. In Princeton's High Contrast Imaging Laboratory we demonstrate that the IEKF allows wavefront correction at least as fast as with a Kalman filter and provides the most accurate detection of a faint companion. The nonlinear IEKF formalism allows us to pursue other strategies such as parameter estimation to improve wavefront correction.

Coronagraphs of the apodized pupil and shaped pupil varieties use the Fraunhofer diffraction properties of amplitude masks to create regions of high contrast in the vicinity of a target star. Here we present a hybrid coronagraph architecture in which a binary, hard-edged shaped pupil mask replaces the gray, smooth apodizer of the apodized pupil Lyot coronagraph (APLC). For any contrast and bandwidth goal in this configuration, as long as the prescribed region of contrast is restricted to a finite area in the image, a shaped pupil is the apodizer with the highest transmission. We relate the starlight cancellation mechanism to that of the conventional APLC. We introduce a new class of solutions in which the amplitude profile of the Lyot stop, instead of being fixed as a padded replica of the telescope aperture, is jointly optimized with the apodizer. Finally, we describe shaped pupil Lyot coronagraph (SPLC) designs for the baseline architecture of the Wide-Field Infrared Survey Telescope-Astrophysics Focused Telescope Assets (WFIRST-AFTA) coronagraph. These SPLCs help to enable two scientific objectives of the WFIRST-AFTA mission: (1) broadband spectroscopy to characterize exoplanet atmospheres in reflected starlight and (2) debris disk imaging.

The coronagraph instrument on the WFIRST-AFTA mission study has two coronagraphic architectures, shaped pupil and hybrid Lyot, which may be interchanged for use in different observing scenarios. Each architecture relies on newly-developed mask components to function in the presence of the AFTA aperture, and so both must be matured to a high technology readiness level (TRL) in advance of the mission. A series of milestones were set to track the development of the technologies required for the instrument; in this paper, we report on completion of WFIRST-AFTA Coronagraph Milestone 2---a narrowband $10^{-8}$ contrast test with static aberrations for the shaped pupil---and the plans for the upcoming broadband Coronagraph Milestone 5.

Stellar coronagraph performance is highly sensitive to optical aberrations. In order to effectively suppress starlight for exoplanet imaging applications, low-order wavefront aberrations entering a coronagraph such as tip-tilt, defocus and coma must be determined and compensated. Previous authors have established the utility of pupil-plane masks (both non-redundant/sparse-aperture and generally asymmetric aperture masks) for wavefront sensing. Here we show how a sparse aperture mask (SAM) can be integrated with a coronagraph to measure low-order, differential phase aberrations. Starlight rejected by the coronagraph's focal plane stop is collimated to a relay pupil, where the mask forms an interference fringe pattern on a subsequent detector. Our numerical Fourier propagation models show that the information encoded in the fringe intensity distortions is sufficient to accurately discriminate and estimate Zernike phase modes extending from tip-tilt up to radial degree $n=5$, with amplitude up to $\lambda/20$ RMS. The SAM sensor can be integrated with both Lyot and shaped pupil coronagraphs (SPC) at no detriment to the science beam quality. We characterize the reconstruction accuracy and the performance under low flux/short exposure time conditions, and place it in context of other coronagraph wavefront sensing schemes.

This report describes the 2014 study by the Science Definition Team (SDT) of the Wide-Field Infrared Survey Telescope (WFIRST) mission. It is a space observatory that will address the most compelling scientific problems in dark energy, exoplanets and general astrophysics using a 2.4-m telescope with a wide-field infrared instrument and an optical coronagraph. The Astro2010 Decadal Survey recommended a Wide Field Infrared Survey Telescope as its top priority for a new large space mission. As conceived by the decadal survey, WFIRST would carry out a dark energy science program, a microlensing program to determine the demographics of exoplanets, and a general observing program utilizing its ultra wide field. In October 2012, NASA chartered a Science Definition Team (SDT) to produce, in collaboration with the WFIRST Study Office at GSFC and the Program Office at JPL, a Design Reference Mission (DRM) for an implementation of WFIRST using one of the 2.4-m, Hubble-quality telescope assemblies recently made available to NASA. This DRM builds on the work of the earlier WFIRST SDT, reported by Green et al. (2012) and the previous WFIRST-2.4 DRM, reported by Spergel et. (2013). The 2.4-m primary mirror enables a mission with greater sensitivity and higher angular resolution than the 1.3-m and 1.1-m designs considered previously, increasing both the science return of the primary surveys and the capabilities of WFIRST as a Guest Observer facility. The addition of an on-axis coronagraphic instrument to the baseline design enables imaging and spectroscopic studies of planets around nearby stars.

We describe the expected scientific capabilities of CHARIS, a high-contrast integral-field spectrograph (IFS) currently under construction for the Subaru telescope. CHARIS is part of a new generation of instruments, enabled by extreme adaptive optics (AO) systems (including SCExAO at Subaru), that promise greatly improved contrasts at small angular separation thanks to their ability to use spectral information to distinguish planets from quasistatic speckles in the stellar point-spread function (PSF). CHARIS is similar in concept to GPI and SPHERE, on Gemini South and the Very Large Telescope, respectively, but will be unique in its ability to simultaneously cover the entire near-infrared $J$, $H$, and $K$ bands with a low-resolution mode. This extraordinarily broad wavelength coverage will enable spectral differential imaging down to angular separations of a few $\lambda/D$, corresponding to $\sim$$0.\!\!''1$. SCExAO will also offer contrast approaching $10^{-5}$ at similar separations, $\sim$$0.\!\!''1$--$0.\!\!''2$. The discovery yield of a CHARIS survey will depend on the exoplanet distribution function at around 10 AU. If the distribution of planets discovered by radial velocity surveys extends unchanged to $\sim$20 AU, observations of $\sim$200 mostly young, nearby stars targeted by existing high-contrast instruments might find $\sim$1--3 planets. Carefully optimizing the target sample could improve this yield by a factor of a few, while an upturn in frequency at a few AU could also increase the number of detections. CHARIS, with a higher spectral resolution mode of $R \sim 75$, will also be among the best instruments to characterize planets and brown dwarfs like HR 8799 cde and $\kappa$ And b.

Searching for nearby habitable worlds with direct imaging and spectroscopy will require a telescope large enough to provide angular resolution and sensitivity to planets around a significant sample of stars. Segmented telescopes are a compelling option to obtain such large apertures. However, these telescope designs have a complex geometry (central obstruction, support structures, segmentation) that makes high-contrast imaging more challenging. We are developing a new high-contrast imaging testbed at STScI to provide an integrated solution for wavefront control and starlight suppression on complex aperture geometries. We present our approach for the testbed optical design, which defines the surface requirements for each mirror to minimize the amplitude-induced errors from the propagation of out-of-pupil surfaces. Our approach guarantees that the testbed will not be limited by these Fresnel propagation effects, but only by the aperture geometry. This approach involves iterations between classical ray-tracing optical design optimization, and end-to-end Fresnel propagation with wavefront control (e.g. Electric Field Conjugation / Stroke Minimization). The construction of the testbed is planned to start in late Fall 2013.

High-contrast imaging techniques now make possible both imaging and spectroscopy of planets around nearby stars. We present the optical design for the Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS), a lenslet-based, cryogenic integral field spectrograph (IFS) for imaging exoplanets on the Subaru telescope. The IFS will provide spectral information for 138x138 spatial elements over a 2.07 arcsec x 2.07 arcsec field of view (FOV). CHARIS will operate in the near infrared (lambda = 1.15 - 2.5 microns) and will feature two spectral resolution modes of R = 18 (low-res mode) and R = 73 (high-res mode). Taking advantage of the Subaru telescope adaptive optics systems and coronagraphs (AO188 and SCExAO), CHARIS will provide sufficient contrast to obtain spectra of young self-luminous Jupiter-mass exoplanets. CHARIS will undergo CDR in October 2013 and is projected to have first light by the end of 2015. We report here on the current optical design of CHARIS and its unique innovations.

The Astro2010 Decadal Survey recommended a Wide Field Infrared Survey Telescope (WFIRST) as its top priority for a new large space mission. As conceived by the decadal survey, WFIRST would carry out a dark energy science program, a microlensing program to determine the demographics of exoplanets, and a general observing program utilizing its ultra wide field. In October 2012, NASA chartered a Science Definition Team (SDT) to produce, in collaboration with the WFIRST Project Office at GSFC and the Program Office at JPL, a Design Reference Mission (DRM) for an implementation of WFIRST using one of the 2.4-m, Hubble-quality mirror assemblies recently made available to NASA. This DRM builds on the work of the earlier WFIRST SDT, reported by Green et al. (2012). The 2.4-m primary mirror enables a mission with greater sensitivity and higher angular resolution than the 1.3-m and 1.1-m designs considered previously, increasing both the science return of the primary surveys and the capabilities of WFIRST as a Guest Observer facility. The option of adding an on-axis, coronagraphic instrument would enable imaging and spectroscopic studies of planets around nearby stars. This document presents the final report of the SDT.

The Astro2010 Decadal Survey recommended a Wide Field Infrared Survey Telescope (WFIRST) as its top priority for a new large space mission. The report of the WFIRST-AFTA Science Definition Team (SDT) presents a Design Reference Mission for WFIRST that employs one of the 2.4-m, Hubble-quality mirror assemblies recently made available to NASA. The 2.4-m primary mirror enables a mission with greater sensitivity and higher angular resolution than the smaller aperture designs previously considered for WFIRST, increasing both the science return of the primary surveys and the capabilities of WFIRST as a Guest Observer facility. The option of adding an on-axis, coronagraphic instrument would enable imaging and spectroscopic studies of planets around nearby stars. This short article, produced as a companion to the SDT report, summarizes the key points of the WFIRST-2.4 DRM. It highlights the remarkable opportunity that the 2.4-m telescope affords for advances in many fields of astrophysics and cosmology, including dark energy, the demographics and characterization of exoplanets, the evolution of galaxies and quasars, and the stellar populations of the Milky Way and its neighbors.

For a coronagraph to detect faint exoplanets, it will require focal plane wavefront control techniques to continue reaching smaller angular separations and higher contrast levels. These correction algorithms are iterative and the control methods need an estimate of the electric field at the science camera, which requires nearly all of the images taken for the correction. The best way to make such algorithms the least disruptive to science exposures is to reduce the number required to estimate the field. We demonstrate a Kalman filter estimator that uses prior knowledge to create the estimate of the electric field, dramatically reducing the number of exposures required to estimate the image plane electric field while stabilizing the suppression against poor signal-to-noise (SNR). In addition to a significant reduction in exposures, we discuss the relative merit of this algorithm to estimation schemes that do not incorporate prior state estimate history, particularly in regard to estimate error and covariance. Ultimately the filter will lead to an adaptive algorithm which can estimate physical parameters in the laboratory for robustness to variance in the optical train.

We discuss scientific, technical and programmatic issues related to the use of an NRO 2.4m telescope for the WFIRST initiative of the 2010 Decadal Survey. We show that this implementation of WFIRST, which we call "NEW WFIRST," would achieve the goals of the NWNH Decadal Survey for the WFIRST core programs of Dark Energy and Microlensing Planet Finding, with the crucial benefit of deeper and/or wider near-IR surveys for GO science and a potentially Hubble-like Guest Observer program. NEW WFIRST could also include a coronagraphic imager for direct detection of dust disks and planets around neighboring stars, a high-priority science and technology precursor for future ambitious programs to image Earth-like planets around neighboring stars.

Space-based coronagraphs for future earth-like planet detection will require focal plane wavefront control techniques to achieve the necessary contrast levels. These correction algorithms are iterative and the control methods require an estimate of the electric field at the science camera, which requires nearly all of the images taken for the correction. We demonstrate a Kalman filter estimator that uses prior knowledge to create the estimate of the electric field, dramatically reducing the number of exposures required to estimate the image plane electric field. In addition to a significant reduction in exposures, we discuss the relative merit of this algorithm to other estimation schemes, particularly in regard to estimate error and covariance. As part of the reduction in exposures we also discuss a novel approach to generating the diversity required for estimating the field in the image plane. This uses the stroke minimization control algorithm to choose the probe shapes on the deformable mirrors, adding a degree of optimality to the problem and once again reducing the total number of exposures required for correction. Choosing probe shapes has been largely unexplored up to this point and is critical to producing a well posed set of measurements for the estimate. Ultimately the filter will lead to an adaptive algorithm which can estimate physical parameters in the laboratory and optimize estimation.

The Stroke Minimization algorithm developed at the Princeton High Contrast Imaging Laboratory has proven symmetric dark hole generation using minimal stroke on two deformable mirrors (DM) in series. The windowed approach to Stroke Minimization has proven symmetric dark holes over small bandwidths by using three wavelengths to define the bandwidth of correction in the optimization problem. We address the relationship of amplitude and phase aberrations with wavelength, how this changes with multiple DMs, and the implications for simultaneously correcting both to achieve symmetric dark holes. Operating Stroke Minimization in the windowed configuration requires multiple wavelength estimates. To save on exposures, a single estimate is extrapolated to bounding wavelengths using the established relationship in wavelength to produce multiple estimates of the image plane electric field. Here we demonstrate better performance by improving this extrapolation of the estimate to other wavelengths. The accuracy of the functional relationship will ultimately bound the achievable bandwidth, therefore as a metric these results are also compared to estimating each wavelength separately. In addition to these algorithm improvements, we also discuss a laboratory upgrade and how it can better simulate broadband starlight. We also discuss the possibility of leveraging two DMs in series to directly estimate the electric field over a narrow bandwidth and the challenges associated with it.

Recent developments in high-contrast imaging techniques now make possible both imaging and spectroscopy of planets around nearby stars. We present the conceptual design of the Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS), a lenslet-based, cryogenic integral field spectrograph (IFS) for imaging exoplanets on the Subaru telescope. The IFS will provide spectral information for 140x140 spatial elements over a 1.75 arcsecs x 1.75 arcsecs field of view (FOV). CHARIS will operate in the near infrared (lambda = 0.9 - 2.5 microns) and provide a spectral resolution of R = 14, 33, and 65 in three separate observing modes. Taking advantage of the adaptive optics systems and advanced coronagraphs (AO188 and SCExAO) on the Subaru telescope, CHARIS will provide sufficient contrast to obtain spectra of young self-luminous Jupiter-mass exoplanets. CHARIS is in the early design phases and is projected to have first light by the end of 2015. We report here on the current conceptual design of CHARIS and the design challenges.

Ground-based telescopes equipped with adaptive-optics (AO) systems and specialized science cameras are now capable of directly detecting extrasolar planets. We present the expected scientific capabilities of CHARIS, the Coronagraphic High Angular Resolution Imaging Spectrograph, which is being built for the Subaru 8.2 m telescope of the National Astronomical Observatory of Japan. CHARIS will be implemented behind the new extreme adaptive optics system at Subaru, SCExAO, and the existing 188-actuator system AO188. CHARIS will offer three observing modes over near-infrared wavelengths from 0.9 to 2.4 microns (the y-, J-, H-, and K-bands), including a low-spectral-resolution mode covering this entire wavelength range and a high-resolution mode within a single band. With these capabilities, CHARIS will offer exceptional sensitivity for discovering giant exoplanets, and will enable detailed characterization of their atmospheres. CHARIS, the only planned high-contrast integral field spectrograph on an 8m-class telescope in the Northern Hemisphere, will complement the similar instruments such as Project 1640 at Palomar, and GPI and SPHERE in Chile.

The past decade has seen a significant growth in research targeted at space based observatories for imaging exo-solar planets. The challenge is in designing an imaging system for high-contrast. Even with a perfect coronagraph that modifies the point spread function to achieve high-contrast, wavefront sensing and control is needed to correct the errors in the optics and generate a "dark hole". The high-contrast imaging laboratory at Princeton University is equipped with two Boston Micromachines Kilo-DMs. We review here an algorithm designed to achieve high-contrast on both sides of the image plane while minimizing the stroke necessary from each deformable mirror (DM). This algorithm uses the first DM to correct for amplitude aberrations and the second DM to create a flat wavefront in the pupil plane. We then show the first results obtained at Princeton with this correction algorithm, and we demonstrate a symmetric dark hole in monochromatic light.

The purpose of this paper is to present the results of a theoretical study pertaining to the feasibility of PIAA units using Deformable Mirrors. We begin by reviewing the general derivation of the design equations driving PIAA. We then show how to solve these equations for square apertures and show the performance of pure PIAA systems in the ray optics regime. We tie these design equations into the study of edge diffraction effects, and provide a general expression for the field after a full propagation through a PIAA coronagraph. Third, we illustrate how a combination of pre and post apodisers yields to a contrast of 10^10 even in the presence of diffractive effects, for configuration with neither wavefront errors or wavefront control. Finally we present novel PIAA configurations over square apertures which circumvent the constraints on the manufacturing of PIAA optics by inducing the apodisation with two square Deformable Mirrors (DM). Such solutions rely on pupil size smaller than currently envisioned static PIAA solutions and thus require aggressive pre and post-apodizing screens in order to mitigate for diffractive effect between the two mirrors. As a result they are associated to significant loss in performance, throughput in particular.

The specification of polishing requirements for the optics in coronagraphs dedicated to exo-planet detection requires careful and accurate optical modelling. Numerical representations of the propagation of aberrations through the system as well as simulations of the broadband wavefront compensation system using multiple DMs are critical when one devises an error budget for such a class of instruments. In this communication we introduce an analytical tool that serves this purpose for Phase Induced Amplitude Apodisation (PIAA) coronagraphs. We first start by deriving the analytical form of the propagation of a harmonic ripple through a PIAA unit. Using this result we derive the chromaticity of the field at any plane in the optical train of a telescope equipped with such a coronagraph. Finally we study the chromatic response of a sequential DM wavefront actuator correcting such a corrugated field and thus quantify the requirements on the manufacturing of PIAA mirrors

We present here fully optimized two-dimensional pupil apodizations for which no specific geometric constraints are put on the pupil plane apodization, apart from the shape of the aperture itself. Masks for circular and segmented apertures are displayed, with and without central obstruction and spiders. Examples of optimal masks are shown for Subaru, SPICA and JWST. Several high-contrast regions are considered with different sizes, positions, shapes and contrasts. It is interesting to note that all the masks that result from these optimizations tend to have a binary transmission profile.

Observations of binary stars for faint companions with conventional coronagraphic methods are challenging, as both targets will be bright enough to obscure any nearby faint companions if their scattered light is not suppressed. We propose coronagraphic examination of binary stars using an apodized pupil Lyot coronagraph and a pair of actively-controlled image plane masks to suppress both stars simultaneously. The performance is compared to imaging with a band-limited mask, a dual-mask Lyot coronagraph and with no coronagraph at all. An imaging procedure and control system for the masks are also described.

Starting with just the assumption of uniformly distributed orbital orientations, we derive expressions for the distributions of the Keplerian orbital elements as functions of arbitrary distributions of eccentricity and semi-major axis. We present methods for finding the probability density functions of the true anomaly, eccentric anomaly, orbital radius, and other parameters used in describing direct planetary observations. We also demonstrate the independence of the distribution of phase angle, which is highly significant in the study of direct searches, and present examples validating the derived expressions.

We present a vector formulation of an interferometric observation of a star, including the effects of the barycentric motion of the observatory, the proper motions of the star, and the reflex motions of the star due to orbiting planets. We use this model to empirically determine the magnitude and form of the signal due to a single Earth-mass planet orbiting about a sun-mass star. Using bounding values for the known components of the model, we perform a series of expansions, comparing the residuals to this signal. We demonstrate why commonly used first order linearizations of similar measurement models are insufficient for signals of the magnitude of the one due to an Earth-mass planet, and present a consistent expansion which is linear in the unknown quantities, with residuals multiple orders of magnitude below the Earth-mass planet signal. We also discuss numerical issues that can arise when simulating or analyzing these measurements.

We present a framework for the analysis of direct detection planet finding missions using space telescopes. This framework generates simulations of complete missions, with varying populations of planets, to produce ensembles of mission simulations, which are used to calculate distributions of mission science yields. We describe the components of a mission simulation, including the complete description of an arbitrary planetary system, the description of a planet finding instrument, and the modeling of a target system observation. These components are coupled with a decision modeling algorithm, which allows us to automatically generate mission timelines with simple mission rules that lead to an optimized science yield. Along with the details of our implementation of this algorithm, we discuss validation techniques and possible future refinements. We apply this analysis technique to four mission concepts whose common element is a 4m diameter telescope aperture: an internal pupil mapping coronagraph with two different inner working angles, an external occulter, and the THEIA XPC multiple distance occulter. The focus of this study is to determine the ability of each of these designs to achieve one of their most difficult mission goals - the detection and characterization of Earth-like planets in the habitable zone. We find that all four designs are capable of detecting on the order of 5 Earth-like planets within a 5 year mission, even if we assume that only 1 out of every 10 stars has such a planet. The designs do differ significantly in their ability to characterize the planets they find. Along with science yield, we also analyze fuel usage for the two occulter designs, and discuss the strengths and weaknesses of each of the mission concepts.

The Telescope for Habitable Exoplanets and Interstellar/Intergalactic Astronomy (THEIA) is a mission concept study for a flagship-class telescope-occulter system to search for terrestrial planets and perform general astrophysics with a space-based 4m telescope. A number of design options were considered for the occulter and telescope optical systems; in this paper we discuss the design of occulters and coronagraphs for THEIA and examine their merits. We present two optimized occulters: a 25.6m-radius occulter with 19m petals that achieves 10^-12 suppression from 250-1000nm with a 75mas inner working angle, and a 20.0m-radius occulter with 10m petals that achieves 10^-12 suppression from 250-700nm with a 75mas inner working angle. For more widely separated planets (IWA > 108mas), this second occulter is designed to operate at a second closer distance where it provides 10^-12 suppression from 700-1000nm. We have also explored occulter/coronagraph hybrid systems, and found that an AIC coronagraph that exploits the symmetry of the PSF at the occulter can improve performance; however, it requires very accurate tolerances on the occulter manufacturing of the telescope/occulter system as the AIC does not cancel asymmetric terms. Other coronagraphs proved infeasible, primarily due to the fact that the residual starlight from the occulter is not a plane wave, and so is poorly suppressed by the coronagraph.

Over 300 extrasolar planets (exoplanets) have been detected orbiting nearby stars. We now hope to conduct a census of all planets around nearby stars and to characterize their atmospheres and surfaces with spectroscopy. Rocky planets within their star's habitable zones have the highest priority, as these have the potential to harbor life. Our science goal is to find and characterize all nearby exoplanets; this requires that we measure the mass, orbit, and spectroscopic signature of each one at visible and infrared wavelengths. The techniques for doing this are at hand today. Within the decade we could answer long-standing questions about the evolution and nature of other planetary systems, and we could search for clues as to whether life exists elsewhere in our galactic neighborhood.

The Gemini Planet Imager (GPI) is an instrument designed for the Gemini South telescope to image young Jupiter-mass planets in the infrared. To achieve the high contrast needed for this, it employs an apodized pupil Lyot coronagraph (APLC) to remove most of the starlight. Current designs use a partially-transmitting apodizer in the pupil; we examine the use of binary apodizations in the form of starshaped shaped pupils, and present a design that could achieve comparable performance, along with a series of design guidelines for creating shaped pupil versions of APLCs in other systems.

We ask if Earth-like planets (terrestrial mass and habitable-zone orbit) can be detected in multi-planet systems, using astrometric and radial velocity observations. We report here the preliminary results of double-blind calculations designed to answer this question.

A multitude of coronagraphic techniques for the space-based direct detection and characterization of exo-solar terrestrial planets are actively being pursued by the astronomical community. Typical coronagraphs have internal shaped focal plane and/or pupil plane occulting masks which block and/or diffract starlight thereby increasing the planet's contrast with respect to its parent star. Past studies have shown that any internal technique is limited by the ability to sense and control amplitude, phase (wavefront) and polarization to exquisite levels - necessitating stressing optical requirements. An alternative and promising technique is to place a starshade, i.e. external occulter, at some distance in front of the telescope. This starshade suppresses most of the starlight before entering the telescope - relaxing optical requirements to that of a more conventional telescope. While an old technique it has been recently been advanced by the recognition that circularly symmetric graded apodizers can be well approximated by shaped binary occulting masks. Indeed optimal shapes have been designed that can achieve smaller inner working angles than conventional coronagraphs and yet have high effective throughput allowing smaller aperture telescopes to achieve the same coronagraphic resolution and similar sensitivity as larger ones. Herein we report on our ongoing modeling, simulation and optimization of external occulters and show sensitivity results with respect to number and shape errors of petals, spectral passband, accuracy of Fresnel propagation, and show results for both filled and segmented aperture telescopes and discuss acquisition and sensing of the occulter's location relative to the telescope.

One proposed method for finding terrestrial planets around nearby stars is to use two spacecraft--a telescope and a specially shaped occulter that is specifically designed to prevent all but a tiny fraction of the starlight from diffracting into the telescope. As the cost and observing cadence for such a mission will be driven largely by the separation between the two spacecraft, it is critically important to design an occulter that can meet the observing goals while flying as close to the telescope as possible. In this paper, we explore this tradeoff between separation and occulter diameter. More specifically, we present a method for designing the shape of the outer edge of an occulter that is as small as possible and gives a shadow that is deep enough and large enough for a 4m telescope to survey the habitable zones of many stars for Earth-like planets. In particular, we show that in order for a 4m telescope to detect in broadband visible light a planet 0.06 arcseconds from a star shining $10^{10}$ times brighter than the planet requires a specially-shaped occulter 50m in diameter positioned about $72,000$ km in front of the telescope.

Pupil mapping is a promising and unconventional new method for high contrast imaging being considered for terrestrial exoplanet searches. It employs two (or more) specially designed aspheric mirrors to create a high-contrast amplitude profile across the telescope pupil that does not appreciably attenuate amplitude. As such, it reaps significant benefits in light collecting efficiency and inner working angle, both critical parameters for terrestrial planet detection. While much has been published on various aspects of pupil mapping systems, the problem of sensitivity to wavefront aberrations remains an open question. In this paper, we present an efficient method for computing the sensitivity of a pupil mapped system to Zernike aberrations. We then use this method to study the sensitivity of a particular pupil mapping system and compare it to the concentric-ring shaped pupil coronagraph. In particular, we quantify how contrast and inner working angle degrade with increasing Zernike order and rms amplitude. These results have obvious ramifications for the stability requirements and overall design of a planet-finding observatory.

Pupil mapping is a promising and unconventional new method for high contrast imaging being considered for terrestrial exoplanet searches. It employs two (or more) specially designed aspheric mirrors to create a high-contrast amplitude profile across the telescope pupil that does not appreciably attenuate amplitude. As such, it reaps significant benefits in light collecting efficiency and inner working angle, both critical parameters for terrestrial planet detection. While much has been published on various aspects of pupil mapping systems, the problem of sensitivity to wavefront aberrations remains an open question. In this paper, we present an efficient method for computing the sensitivity of a pupil mapped system to Zernike aberrations. We then use this method to study the sensitivity of a particular pupil mapping system and compare it to the concentric-ring shaped pupil coronagraph. In particular, we show how contrast and inner working angle degrade with increasing Zernike order and rms amplitude, which has obvious ramifications for the stability requirements and overall design of a planet-finding observatory.

Current plans call for the first Terrestrial Planet Finder mission, TPF-C, to be a monolithic space telescope with a coronagraph for achieving high contrast. The coronagraph removes the diffracted starlight allowing the nearby planet to be detected. In this paper, we present a model of the planet measurement and noise statistics. We utilize this model to develop two planet detection algorithms, one based on matched filtering of the PSF and one using Bayesian techniques. These models are used to formulate integration time estimates for a planet detection with desired small probabilities of false alarms and missed detections.

The realization that direct imaging of extrasolar planets could be technologically feasible within the next decade or so has inspired a great deal of recent research into high-contrast imaging. We ourselves have contributed several design ideas, all of which can be described as shaped pupil coronagraphs. In this paper, we offer a complete and unified survey of asymmetric shaped pupils designs, some of which have been published in our previous papers. We also introduce a promising new design, which we call barcode masks. These masks achieve the required contrast with a fairly large discovery zone and throughput but most importantly they are perhaps the easiest to manufacture and might therefore stand up best to a refined analysis based on vector propogation techniques.

The past five years has seen a surge in research and innovative ideas for the imaging of extrasolar planets, particular terrestrial ones. We expect that within the next decade a space observatory will be launched with the objective of imaging earthlike planets. Because of the limited lifetime of such a mission and the large number of potential targets, integration time is a critical parameter. In fact, integration time is the primary metric in evaluating various design approaches for the high contrast imaging system. In this paper we present a new approach to determining the existence of a planet in an observed system using Bayesian hypothesis testing. Rather than perform photometry, or rely on vision to determine the existence of a planet, this approach evaluates the image plane data statistically under certain assumptions about the prior probability distributions. We show that extremely high confidence can be achieved in substantially shorter integration times than conventional photometric methods.

We present yet another new family of masks for high-contrast imaging as required for the to-be-built terrestrial planet finder space telescope. The ``best'' design involves a square entrance pupil having a 4-vane spider, a square image-plane mask containing a plus-sign shaped occulter to block the starlight inside 0.6 lambda/D, and a Lyot-plane mask consisting of a rectangular array of rectangular opennings. Using Fraunhofer analysis, we show that the optical system can image a planet 10^{-10} times as bright as an on-axis star in four rectangular regions given by {(xi,zeta): 1.4 < | xi | < 20, 1.4 < | zeta | < 20}. Since the design involves an image plane mask, pointing error is an issue. We show that the design can tolerate pointing errors of about 0.05 lambda/D. The inclusion of a 4-vane spider in the entrance pupil provides the possibility to build a mirror-only on-axis system thereby greatly reducing the negative effects of polarization. Each of the masks can be realized as two masks consisting of stripes of opaque material with the stripes oriented at right angles to each other. We call these striped masks barcode masks. We show that it is sufficient for the barcode masks by themselves to provide 10^{-5} contrast. This then guarantees that the full system will provide the required 10^{-10} contrast.

Recently, we introduced a class of shaped pupil masks, called spiderweb masks, that produce point spread functions having annular dark zones. With such masks, a single image can be used to probe a star for extrasolar planets. In this paper, we introduce a new class of shaped pupil masks that also provide annular dark zones. We call these masks starshaped masks. Given any circularly symmetric apodization function, we show how to construct a corresponding starshaped mask that has the same point-spread function (out to any given outer working distance) as obtained by the apodization.

Motivated by the desire to image exosolar planets, recent work by us and others has shown that high-contrast imaging can be achieved using specially shaped pupil masks. To date, the masks we have designed have been symmetric with respect to a cartesian coordinate system but were not rotationally invariant, thus requiring that one take multiple images at different angles of rotation about the central point in order to obtain high-contrast in all directions. In this paper, we present a new class of masks that have rotational symmetry and provide high-contrast in all directions with just one image. These masks provide the required 10^{-10} level of contrast to within 4 lambda/D, and in some cases 3 lambda/D, of the central point, which is deemed necessary for exosolar planet finding/imaging. They are also well-suited for use on ground-based telescopes, and perhaps NGST too, since they can accommodate central obstructions and associated support spiders.