The Particle Telescope (PATE) of FORESAIL-1 mission is described. FORESAIL-1 is a CubeSat mission to polar Low Earth Orbit. Its scientific objectives are to characterize electron precipitation from the radiation belts and to observe energetic neutral atoms (ENAs) originating from the Sun during the strongest solar flares. For that purpose, the 3-unit CubeSat carries a particle telescope that measures energetic electrons in the nominal energy range of 80--800 keV in seven energy channels and energetic protons at 0.3--10 MeV in ten channels. In addition, particles penetrating the whole telescope at higher energies will be measured in three channels: one $>$800 keV electron channel, two integral proton channels at $>$10 MeV energies. The instrument contains two telescopes at right angles to each other, one measuring along the spin axis of the spacecraft and one perpendicular to it. During a spin period (nominally 15 s), the rotating telescope will, thus, deliver angular distributions of protons and electrons, at 11.25-degree clock-angle resolution, which enables one to accurately determine the pitch-angle distribution and separate the trapped and precipitating particles. During the last part of the mission, the rotation axis will be accurately pointed toward the Sun, enabling the measurement of the energetic hydrogen from that direction. Using the geomagnetic field as a filter and comparing the rates observed by the two telescopes, the instrument can observe the solar ENA flux for events similar to the only one so far observed in December 2006. We present the Geant4-simulated energy and angular response functions of the telescope and assess its sensitivity showing that they are adequate to address the scientific objectives of the mission.

The electric solar wind sail (E-sail) is a way to propel a spacecraft by using the natural solar wind as a thrust source. The problem of secular spinrate change was identified earlier which is due to the orbital Coriolis effect and tends to slowly increase or decrease the sail's spinrate, depending on which way the sail is inclined with respect to the solar wind. Here we present an E-sail design and its associated control algorithm which enable spinrate control during propulsive flight by the E-sail effect itself. In the design, every other maintether ("T-tether") is galvanically connected through the remote unit with the two adjacent auxtethers, while the other maintethers ("I-tethers") are insulated from the tethers. This enables one to effectively control the maintether and auxtether voltages separately, which in turn enables spinrate control. We use a detailed numerical simulation to show that the algorithm can fully control the E-sail's spin state in real solar wind. The simulation includes a simple and realistic set of controller sensors: an imager to detect remote unit angular positions and a vector accelerometer. The imager resolution requirement is modest and the accelerometer noise requirement is feasible to achieve. The TI tether rig enables building E-sails that are able to control their spin state fully and yet are actuated by pure tether voltage modulation from the main spacecraft and requiring no functionalities from the remote units during flight.

The shape of a rotating electric solar wind sail under the centrifugal force and solar wind dynamic pressure is modeled to address the sail attitude maintenance and thrust vectoring. The sail rig assumes centrifugally stretched main tethers that extend radially outward from the spacecraft in the sail spin plane. Furthermore, the tips of the main tethers host remote units that are connected by auxiliary tethers at the sail rim. Here, we derive the equation of main tether shape and present both a numerical solution and an analytical approximation for the shape as parametrized both by the ratio of the electric sail force to the centrifugal force and the sail orientation with respect to the solar wind direction. The resulting shape is such that near the spacecraft, the roots of the main tethers form a cone, whereas towards the rim, this coning is flattened by the centrifugal force, and the sail is coplanar with the sail spin plane. Our approximation for the sail shape is parametrized only by the tether root coning angle and the main tether length. Using the approximate shape, we obtain the torque and thrust of the electric sail force applied to the sail. As a result, the amplitude of the tether voltage modulation required for the maintenance of the sail attitude is given as a torque-free solution. The amplitude is smaller than that previously obtained for a rigid single tether resembling a spherical pendulum. This implies that less thrusting margin is required for the maintenance of the sail attitude. For a given voltage modulation, the thrust vectoring is then considered in terms of the radial and transverse thrust components.

In Coulomb drag propulsion, a long high voltage tether or system of tethers gathers momentum from a natural plasma stream such as solar wind or ionospheric plasma ram flow. A positively polarised tether in the solar wind can be used for efficient general-purpose interplanetary propellantless propulsion (the electric solar wind sail or E-sail), whereas a negatively polarised tether in LEO can be used for efficient deorbiting of satellites (the plasma brake). Aalto-1 is a 3-U cubesat to be launched in May 2016. The satellite carries three scientific experiments including 100 m long Coulomb drag tether experiment. The tether is made of four 25 and 50 micrometre diameter aluminium wires that are ultrasonically bonded together every few centimetre intervals. The tether can be charged by an onboard voltage source up to one kilovolt positive and negative. The Coulomb drag is measured by monitoring the spin rate.

The solar wind electric sail (E-sail) is a planned in-space propulsion device that uses the natural solar wind momentum flux for spacecraft propulsion with the help of long, charged, centrifugally stretched tethers. The problem of accurately predicting the E-sail thrust is still somewhat open, however, due to a possible electron population trapped by the tether. Here we develop a new type of particle-in-cell (PIC) simulation for predicting E-sail thrust. In the new simulation, electrons are modelled as a fluid, hence resembling hydrid simulation, but in contrast to normal hybrid simulation, the Poisson equation is used as in normal PIC to calculate the self-consistent electrostatic field. For electron-repulsive parts of the potential, the Boltzmann relation is used. For electron-attractive parts of the potential we employ a power law which contains a parameter that can be used to control the number of trapped electrons. We perform a set of runs varying the parameter and select the one with the smallest number of trapped electrons which still behaves in a physically meaningful way in the sense of producing not more than one solar wind ion deflection shock upstream of the tether. By this prescription we obtain thrust per tether length values that are in line with earlier estimates, although somewhat smaller. We conclude that the Boltzmann PIC simulation is a new tool for simulating the E-sail thrust. This tool enables us to calculate solutions rapidly and allows to easily study different scenarios for trapped electrons.

The electric solar wind sail (E-sail) propellantless propulsion device uses long, charged metallic tethers to tap momentum from the solar wind to produce spacecraft propulsion. If flying through planetary or moon eclipse, the long E-sail tethers can undergo significant thermal contraction and expansion. Rapid shortening of the tether increases its tension due to inertia of the tether and a Remote Unit that is located on the tether tip (a Remote Unit is part of typical E-sail designs). We analyse by numerical simulation the conditions under which eclipse induced stresses are safe for E-sail tethers. We calculate the closest safe approach distances for Earth, Moon, Venus, Mars, Jupiter, Ceres and an exemplary 300 km main belt asteroid Interamnia for circular, parabolic and hyperbolic orbits. We find that any kind of eclipsing is safe beyond approximately 2.5 au distance, but for terrestrial planets safety depends on the parameters of the orbit. For example, for Mars the safe distance with 20 km E-sail tether lies between Phobos and Deimos orbits.

The novel propellantless electric solar wind sail concept promises efficient low thrust transportation in the Solar System outside Earth's magnetosphere. Combined with asteroid mining to provide water and synthetic cryogenic rocket fuel in orbits of Earth and Mars, possibilities for affordable continuous manned presence on Mars open up. Orbital fuel and water enable reusable bidirectional Earth-Mars vehicles for continuous manned presence on Mars and allow smaller fuel fraction of spacecraft than what is achievable by traditional means. Water can also be used as radiation shielding of the manned compartment, thus reducing the launch mass further. In addition, the presence of fuel in the orbit of Mars provides the option for an all-propulsive landing, thus potentially eliminating issues of heavy heat shields and augmenting the capability of pinpoint landing. With this E-sail enabled scheme, the recurrent cost of continuous bidirectional traffic between Earth and Mars might ultimately approach the recurrent cost of running the International Space Station, ISS.

The electric solar wind sail produces thrust by centrifugally spanned high voltage tethers interacting with the solar wind protons. The sail attitude can be controlled and attitude maneuvers are possible by tether voltage modulation synchronous with the sail rotation. Especially, the sail can be inclined with respect to the solar wind direction to obtain transverse thrust to change the osculating orbit angular momentum. Such an inclination has to be maintained by a continual control voltage modulation. Consequently, the tether voltage available for the thrust is less than the maximum voltage provided by the power system. Using a spherical pendulum as a model for a single rotating tether, we derive analytical estimations for the control efficiency for two separate sail control modes. One is a continuous control modulation that corresponds to strictly planar tether tip motion. The other is an on-off modulation with the tether tip moving along a closed loop on a saddle surface. The novel on-off mode is introduced here to both amplify the transverse thrust and reduce the power consumption. During the rotation cycle, the maximum voltage is applied to the tether only over two thrusting arcs when most of the transverse thrust is produced. In addition to the transverse thrust, we obtain the thrusting angle and electric power consumption for the two control modes. It is concluded that while the thrusting angle is about half of the sail inclination for the continuous modulation it approximately equals to the inclination angle for the on-off modulation. The efficiency of the on-off mode is emphasized when power consumption is considered, and the on-off mode can be used to improve the propulsive acceleration through the reduced power system mass.

A charged tether or wire experiences Coulomb drag when inserted into flowing plasma. In the solar wind the Coulomb drag can be utilised as efficient propellantless interplanetary propulsion as the electric solar wind sail (electric sail, E-sail). In low Earth orbit (LEO) the same plasma physical effect can be utilised for efficient low-thrust deorbiting of space debris objects (the plasma brake). The E-sail is rotationally stabilised while the deorbiting Coulomb drag devices According to numerical estimates, Coulomb drag devices have very promising performance figures, both for interplanetary propulsion and for deorbiting in LEO. Much of the technology is common to both applications. E-sail technology development was carried out in ESAIL FP7 project (2011-2013) which achieved TRL 4-5 for key hardware components that can enable 1 N class interplanetary E-sail weighing less than 200 kg. The thrust of the E-sail scales as inverse solar distance and its power consumption (nominally 700 W/N at 1 au) scales as the inverse distance squared. As part of the ESAIL project, a continuous 1 km sample of E-sail tether was produced by an automatic and scalable "tether factory". The manufacturing method uses ultrasonic wire to wire bonding which was developed from ordinary wire to plate bonding for the E-sail purpose. Also a "Remote Unit" device which takes care of deployment and spin rate control was prototyped and successfully environmentally tested. Our Remote Unit prototype is operable in the solar distance range of 0.9-4 au. The 1-U CubeSat ESTCube-1 was launched in May 2013 and it will try to measure the Coulomb drag acting on a 10 m long tether in LEO when charged to 500 V positive or negative. A more advanced version of the experiment with 100 m tether is under preparation and will be launched in 2015 with the Aalto-1 3-U CubeSat to polar LEO.

The plasma brake is a thin negatively biased tether which has been proposed as an efficient concept for deorbiting satellites and debris objects from low Earth orbit. We simulate the interaction with the ionospheric plasma ram flow with the plasma brake tether by a high performance electrostatic particle in cell code to evaluate the thrust. The tether is assumed to be perpendicular to the flow. We perform runs for different tether voltage, magnetic field orientation and plasma ion mass. We show that a simple analytical thrust formula reproduces most of the simulation results well. The interaction with the tether and the plasma flow is laminar (i.e., smooth and not turbulent) when the magnetic field is perpendicular to the tether and the flow. If the magnetic field is parallel to the tether, the behaviour is unstable and thrust is reduced by a modest factor. The case when the magnetic field is aligned with the flow can also be unstable, but does not result in notable thrust reduction. We also fix an error in an earlier reference. According to the simulations, the predicted thrust of the plasma brake is large enough to make the method promising for low Earth orbit (LEO) satellite deorbiting. As a numerical example we estimate that a 5 km long plasma brake tether weighing 0.055 kg could produce 0.43 mN breaking force which is enough to reduce the orbital altitude of a 260 kg object mass by 100 km during one year.

The electric solar wind sail is a novel propellantless space propulsion concept. According to numerical estimates, the electric solar wind sail can produce a large total impulse per propulsion system mass. Here we consider using a 0.5 N electric solar wind sail for boosting a 550 kg spacecraft to Uranus in less than 6 years. The spacecraft is a stack consisting of the electric solar wind sail module which is jettisoned roughly at Saturn distance, a carrier module and a probe for Uranus atmospheric entry. The carrier module has a chemical propulsion ability for orbital corrections and it uses its antenna for picking up the probe's data transmission and later relaying it to Earth. The scientific output of the mission is similar to what the Galileo Probe did at Jupiter. Measurements of the chemical and isotope composition of the Uranian atmosphere can give key constraints to different formation theories of the Solar System. A similar method could also be applied to other giant planets and Titan by using a fleet of more or less identical probes.

We show that by having the auxtethers made partly or completely of conducting material and by controlling their voltages, it is possible to control the spin rate of the electric solar wind sail by using the electric sail effect itself. The proposed intrinsic spin rate control scheme has enough control authority to overcome the secular change of the spin rate due to orbital Coriolis effect.

The scientific mission of ESTCube-1, launched in May 2013, is to measure the Electric solar wind sail (E-sail) force in orbit. The experiment is planned to push forward the development of E-sail, a propulsion method recently invented at the Finnish Meteorological Institute. E-sail is based on extracting momentum from the solar wind plasma flow by using long thin electrically charged tethers. ESTCube-1 is equipped with one such tether, together with hardware capable of deploying and charging it. At the orbital altitude of ESTCube-1 (660--680~km) there is no solar wind present. Instead, ESTCube-1 shall observe the interaction between the charged tether and the ionospheric plasma. The ESTCube-1 payload uses a 10-meter, partly two-filament E-sail tether and a motorized reel on which it is stored. The tether shall be deployed from a spinning satellite with the help of centrifugal force. An additional mass is added at the tip of the tether to assist with the deployment. During E-sail experiment the tether shall be charged to 500~V potential. Both positive and negative voltages shall be experimented with. The voltage is provided by a dedicated high voltage source and delivered to the tether through a slip ring contact. When the negative voltage is applied to the tether, the satellite body is expected to attract electron flow capable of compensating for the ion flow, which runs to the tether from the surrounding plasma. With the positive voltage applied, onboard cold cathode electron guns are used to remove excess electrons to maintain the positive voltage of the tether. In this paper we present the design and structure of the tether payload of ESTCube-1.

We analyse the potential of the electric solar wind sail for solar system space missions. Applications studied include fly-by missions to terrestrial planets (Venus, Mars and Phobos, Mercury) and asteroids, missions based on non-Keplerian orbits (orbits that can be maintained only by applying continuous propulsive force), one-way boosting to outer solar system, off-Lagrange point space weather forecasting and low-cost impactor probes for added science value to other missions. We also discuss the generic idea of data clippers (returning large volumes of high resolution scientific data from distant targets packed in memory chips) and possible exploitation of asteroid resources. Possible orbits were estimated by orbit calculations assuming circular and coplanar orbits for planets. Some particular challenge areas requiring further research work and related to some more ambitious mission scenarios are also identified and discussed.

We consider a freely guided photonic blade (FGPB) which is a centrifugally stretched sheet of photonic sail membrane that can be tilted by changing the centre of mass or by other means. The FGPB can be installed at the tip of each main tether of an electric solar wind sail (E-sail) so that one can actively manage the tethers to avoid their mutual collisions and to modify the spin rate of the sail if needed. This enables a more scalable and modular E-sail than the baseline approach where auxiliary tethers are used for collision avoidance. For purely photonic sail applications one can remove the tethers and increase the size of the blades to obtain a novel variant of the heliogyro that can have a significantly higher packing density than the traditional heliogyro. For satellite deorbiting in low Earth orbit (LEO) conditions, analogous designs exist where the E-sail effect is replaced by the negative polarity plasma brake effect and the photonic pressure by atmospheric drag. We conclude that the FGPB appears to be an enabling technique for diverse applications. We also outline a way of demonstrating it on ground and in LEO at low cost.

The electric solar wind sail (E-sail) is a novel, efficient propellantless propulsion concept which utilises the natural solar wind for spacecraft propulsion with the help of long centrifugally stretched charged tethers. The E-sail requires auxiliary propulsion applied to the tips of the main tethers for creating the initial angular momentum and possibly for modifying the spinrate later during flight to counteract the orbital Coriolis effect and possibly for mission specific reasons. We introduce the possibility of implementing the required auxiliary propulsion by small photonic blades (small radiation pressure solar sails). The blades would be stretched centrifugally. We look into two concepts, one with and one without auxiliary tethers. The use of photonic blades has the benefit of providing sufficient spin modification capability for any E-sail mission while keeping the technology fully propellantless. We conclude that the photonic blades appear to be a feasible and attractive solution to E-sail spinrate control.

The motivation to build spaceborne interferometric arrays for low-frequency radio astronomy is widely recognised because frequencies below the ionospheric cutoff are inaccessible for ground-based radio telescopes. We discuss the theoretical possibilities to use low-frequency spacecraft arrays to detect signals from magnetized extrasolar planets, including earthlike ones. A major uncertainty that prohibits us from knowing if it is possible to detect exoplanet cyclotron maser signals is the incomplete knowledge of the properties of the interstellar plasma. We also present some ideas of how to construct efficient and affordable space-based radio telescopes. We discuss two possibilities, a log-periodic antenna in the spin plane and a two-spacecraft concept where one spacecraft holds a large parabolic wire mesh reflector and the other one contains the receiver. In the latter case, the effective area could be of the order of 1 km$^2$. The purpose of the paper is to stress once more the importance of spaceborne low-frequency measurements by bringing in the intriguing possibility of detecting earthlike exoplanet radio emissions and to demonstrate that building even very large low-frequency antennas in space is not necessarily too expensive.