Repeating fast radio bursts (FRBs) present excellent opportunities to identify FRB progenitors and host environments, as well as decipher the underlying emission mechanism. Detailed studies of repeating FRBs might also hold clues to the origin of FRBs as a population. We aim to detect the first two repeating FRBs: FRB 121102 (R1) and FRB 180814.J0422+73 (R2), and characterise their repeat statistics. We also want to significantly improve the sky localisation of R2. We use the Westerbork Synthesis Radio Telescope to conduct extensive follow-up of these two repeating FRBs. The new phased-array feed system, Apertif, allows covering the entire sky position uncertainty of R2 with fine spatial resolution in one pointing. We characterise the energy distribution and the clustering of detected R1 bursts. We detected 30 bursts from R1. Our measurements indicate a dispersion measure of 563.5(2) pc cm$^{-3}$, suggesting a significant increase in DM over the past few years. We place an upper limit of 8% on the linear polarisation fraction of the brightest burst. We did not detect any bursts from R2. A single power-law might not fit the R1 burst energy distribution across the full energy range or widely separated detections. Our observations provide improved constraints on the clustering of R1 bursts. Our stringent upper limits on the linear polarisation fraction imply a significant depolarisation, either intrinsic to the emission mechanism or caused by the intervening medium, at 1400 MHz that is not observed at higher frequencies. The non-detection of any bursts from R2 implies either a highly clustered nature of the bursts, a steep spectral index, or a combination of both. Alternatively, R2 has turned off completely, either permanently or for an extended period of time.

This paper discusses an outdoor test facility for the noise characterization of active antenna arrays, using measurement results of array noise temperatures in the order of 50 K for a number of small aperture arrays. The measurement results are obtained by a Y-factor method with hot and a cold noise sources, with an absorber at room temperature as the hot load and the cold sky as the cold load. The effect of shielding the arrays by the test facility, with respect to noise and RFI from the environment, will also be discussed.

Interferometry with phased-array feeds (PAFs) presents new calibration challenges in comparison with single-pixel feeds. In particular, temporal instability of the compound beam patterns due to element gain drifts (EGDs) can produce calibration artefacts in interferometric images. To translate imaging dynamic range requirements into PAF hardware and calibration requirements, we must learn to relate EGD levels to imaging artefact levels. We present a MeqTrees-based simulations framework that addresses this problem, and apply it to the APERTIF prototype currently in development for the WSRT.

The purpose of this report is to document the noise performance of a complex beamforming array antenna system and to characterize the recently developed noise measurement facility called THACO, which was developed at ASTRON. The receiver system includes the array antenna of strongly coupled 144 TSA elements, 144 Low Noise Amplifiers (LNAs) (Tmin =35-40K) and the data recording/storing facilities of the initial test station that allow for off-line digital beamforming. The primary goal of this study is to compare the measured receiver noise temperatures with the simulated values for several practical beamformers, and to predict the associated receiver noise coupling contribution, antenna thermal noise and ground noise pick-up (due to the back radiation).

Aperture arrays have been studied extensively for application in the next generation of large radio telescopes for astronomy, requiring extremely low noise performance. Prototype array systems need to demonstrate the low noise potential of aperture array technology. This paper presents noise measurements for an Aperture Array tile of 144 dual-polarized tapered slot antenna (TSA) elements, originally built and characterized for use as a Phased Array Feed for application in an L-band radio astronomical receiving system. The system noise budget is given and the dependency of the measured noise temperatures on the beam steering is discussed. A comparison is made of the measurement results with simulations of the noise behavior using a system noise model. This model includes the effect of receiver noise coupling, resulting from a changing active reflection coefficient and array noise contribution as a function of beam steering. Measurement results clearly demonstrate the validity of the model and thus the concept of active reflection coefficient for the calculation of effective system noise temperatures. The presented array noise temperatures, with a best measured value of 45 K, are state-of-the-art for room temperature aperture arrays in the 1 GHz range and illustrate their low noise potential.

A concept of an axi-symmetric dish as antenna reflector for the next generation radio telescope - the Square Kilometre Array (SKA) - is presented. The reflector is based on the use of novel thermoplastic composite material (reinforced with carbon fibre) in the context of the telescope design with wide band single pixel feeds. The baseline of this design represents an array of 100's to 1000's reflector antennas of 15-m diameter and covers frequencies from <1 to 10 GHz. The purpose of our study is the analysis of the production cost of the dish and its performance in combination with a realistic wideband feed (such as the 'Eleven Antenna' feed) over a wide frequency band and a range of elevation angles. The presented initial simulation results inidicate the potential of the proposed dish concept for low-cost and mass production and demonstrate sensitivity comparable to that of the presently considered off-set Gregorian reflector antenna with the same projected aperture area. We expect this observation to be independent of the choice of the feed, as several other single-pixel wideband feeds (that have been reported in the literature) have similar beamwidth and phase center location, both being rather constant with frequency.

The results of four recently introduced beamforming schemes for phased array systems are discussed, each of which is capable to provide high sensitivity and accurate polarimetric performance of array-based radio telescopes. Ideally, a radio polarimeter should recover the actual polarization state of the celestial source, and thus compensate for unwanted polarization degradation effects which are intrinsic to the instrument. In this paper, we compare the proposed beamforming schemes through an example of a practical phased array system (APERTIF prototype) and demonstrate that the optimal beamformer, the max-SLNR beamformer, the eigenvector beamformer, and the bi-scalar beamformer are sensitivity equivalent but lead to different polarization state solutions, some of which are sub-optimal.

We describe a focal plane array (FPA) system, called Apertif, that is being developed for the Westerbork Synthesis Radio Telescope (WSRT). The aim of Apertif is to increase the instantaneous field of view of the WSRT by a factor of 37 and its observing bandwidth to 300 MHz with high spectral resolution. This system will turn the WSRT into an effective survey telescope with scientific applications such as deep imaging surveys of the northern sky of HI and OH emission, of the polarised continuum and efficient searches for pulsars and transients. Such surveys will detect the HI in more than 100,000 galaxies out to z = 0.4, will allow to determine the detailed structure of the magnetic field of the Galaxy, and will discover more than 1,000 pulsars. We present experimental results obtained with a prototype FPA installed in one of the WSRT dishes. These results demonstrate that FPAs do have the performance that is required to make all these surveys possible.

In this paper we describe a focal plane array (FPA) prototype, based on Vivaldi elements, developed for the Westerbork Synthesis Radio Telescope (WSRT) to increase its instantaneous field of view by a factor 25 and double its current bandwidth. This prototype is the first step in a project that has the ambition to equip most of the WSRT antennas with FPAs to improve the survey speed of the telescope. Examples of scientific applications are surveys of the northern sky in polarised continuum and HI emission, and efficient searches for pulsars and transients.