Normalized to: Henault, F.
[1]
oai:arXiv.org:1909.05224 [pdf] - 1959914
New concepts for calibrating non-common path aberrations in adaptive
optics and coronagraph systems
Submitted: 2019-09-11
Non Common Path Aberrations (NCPA) are often considered as a critical issue
in Adaptive Optics (AO) systems, since they introduce bias errors between real
wavefronts propagating to the science detectors and those measured by the
Wavefront Sensor (WFS). This is especially true when the AO system is coupled
to a coronagraph instrument intended for the discovery and characterization of
extra-solar planets, because useful planet signals could be mistaken with
residual speckles generated by NCPA. Therefore, compensating for those errors
is of prime importance and is already the scope of a few theoretical studies
and experimental validations on-sky. This communication presents the conceptual
optical design of a pseudo-interferometer arrangement suitable to accurate NCPA
calibration, based on two WFS cooperating in real-time. The concept is
applicable to both classical imaging and spectroscopy assisted by AO, and to
high-contrast coronagraphs searching for habitable extra-solar planets.
Practical aspects are discussed, such as the choice of WFS and coronagraph
types, or specific requirements on additional hardware components, e.g.
dichroic beamsplitters
[2]
oai:arXiv.org:1909.05175 [pdf] - 1959911
Hartmann vs. reverse Hartmann test: a Fourier optics point of view
Submitted: 2019-09-11
The Shack-Hartmann Wavefront Sensor (WFS) is well-known in the fields of
optical metrology, wavefront sensing in astronomy, and ophthalmologic control
applications. The purpose of this communication is to bring new insights on the
historical Hartmann test and to compare it with the less known reverse Hartmann
test, where the locations of the pupil mask and observed image planes are
exchanged. Both tests can actually be interpreted by using the formalism of
Fourier optics, i.e. Fraunhofer diffraction for the Shack-Hartmann and Fresnel
diffraction in the reverse configuration. The principles of these models are
firstly described in the communication. The results of numerical simulations
are then presented, allowing comparing both optical arrangements from the
Fourier optics point of view, in terms of achievable wavefront measurement
accuracy. They show that a WFS based on the reverse Hartmann test may globally
achieve the same performance as the classical Shack-Hartmann
[3]
oai:arXiv.org:1805.11994 [pdf] - 1694205
Analysis of azimuthal phase mask coronagraphs
Submitted: 2018-05-30
In this paper is presented an analytical study of the azimuthal phase-mask
coronagraph currently envisioned for detecting and characterizing extra-solar
planets. Special emphasis is put on the physical and geometrical interpretation
of the mathematical development. Two necessary conditions are defined for
achieving full extinction in the pupil plane of the coronagraph, stating that
the complex amplitude generated by the phase mask should have zero average, on
the one hand, and its Fourier coefficients should only be even, on the other
hand. Examples of such phase functions are reviewed, including optical
vortices, four-quadrant phase masks, and azimuthal cosine phase functions.
Hints for building more sophisticated functions are also given. Finally, a
simplified expression of light leaks due to mask imperfection is proposed
[6]
oai:arXiv.org:1609.02477 [pdf] - 1510370
A detector interferometric calibration experiment for high precision
astrometry
Crouzier, A.;
Malbet, F.;
Henault, F.;
Leger, A.;
Cara, C.;
LeDuigou, J. M.;
Preis, O.;
Kern, P.;
Delboulbe, A.;
Martin, G.;
Feautrier, P.;
Stadler, E.;
Lafrasse, S.;
Rochat, S.;
Ketchazo, C.;
Donati, M.;
Doumayrou, E.;
Lagage, P. O.;
Shao, M.;
Goullioud, R.;
Nemati, B.;
Zhai, C.;
Behar, E.;
Potin, S.;
Saint-Pe, M.;
Dupont, J.
Submitted: 2016-09-08
Context: Exoplanet science has made staggering progress in the last two
decades, due to the relentless exploration of new detection methods and
refinement of existing ones. Yet astrometry offers a unique and untapped
potential of discovery of habitable-zone low-mass planets around all the
solar-like stars of the solar neighborhood. To fulfill this goal, astrometry
must be paired with high precision calibration of the detector.
Aims: We present a way to calibrate a detector for high accuracy astrometry.
An experimental testbed combining an astrometric simulator and an
interferometric calibration system is used to validate both the hardware needed
for the calibration and the signal processing methods. The objective is an
accuracy of 5e-6 pixel on the location of a Nyquist sampled polychromatic point
spread function.
Methods: The interferometric calibration system produced modulated Young
fringes on the detector. The Young fringes were parametrized as products of
time and space dependent functions, based on various pixel parameters. The
minimization of func- tion parameters was done iteratively, until convergence
was obtained, revealing the pixel information needed for the calibration of
astrometric measurements.
Results: The calibration system yielded the pixel positions to an accuracy
estimated at 4e-4 pixel. After including the pixel position information, an
astrometric accuracy of 6e-5 pixel was obtained, for a PSF motion over more
than five pixels. In the static mode (small jitter motion of less than 1e-3
pixel), a photon noise limited precision of 3e-5 pixel was reached.
[7]
oai:arXiv.org:1608.00360 [pdf] - 1494781
The latest results from DICE (Detector Interferometric Calibration
Experiment)
Crouzier, A.;
Malbet, F.;
Henault, F.;
Leger, A.;
Cara, C.;
LeDuigou, J. M.;
Preis, O.;
Kern, P.;
Delboulbe, A.;
Martin, G.;
Feautrier, P.;
Stadler, E.;
Lafrasse, S.;
Rochat, S.;
Ketchazo, C.;
Donati, M.;
Doumayrou, E.;
Lagage, P. O.;
Shao, M.;
Goullioud, R.;
Nemati, B.;
Zhai, C.;
Behar, E.;
Potin, S.;
Saint-Pe, M.;
Dupont, J.
Submitted: 2016-08-01
Theia is an astrometric mission proposed to ESA in 2014 for which one of the
scientific objectives is detecting Earth-like exoplanets in the habitable zone
of nearby solar-type stars. This objective requires the capability to measure
stellar centroids at the precision of 1e-5 pixel. Current state-of-the-art
methods for centroid estimation have reached a precision of about 3e-5 pixel at
two times Nyquist sampling, this was shown at the JPL by the VESTA experiment.
A metrology system was used to calibrate intra and inter pixel quantum
efficiency variations in order to correct pixelation errors. The Theia
consortium is operating a testbed in vacuum in order to achieve 1e-5 pixel
precision for the centroid estimation. The goal is to provide a proof of
concept for the precision requirement of the Theia spacecraft.
The testbed consists of two main sub-systems. The first one produces pseudo
stars: a blackbody source is fed into a large core fiber and lights-up a
pinhole mask in the object plane, which is imaged by a mirror on the CCD. The
second sub-system is the metrology, it projects young fringes on the CCD. The
fringes are created by two single mode fibers facing the CCD and fixed on the
mirror. In this paper we present the latest experiments conducted and the
results obtained after a series of upgrades on the testbed was completed. The
calibration system yielded the pixel positions to an accuracy estimated at 4e-4
pixel. After including the pixel position information, an astrometric accuracy
of 6e-5 pixel was obtained, for a PSF motion over more than 5 pixels. In the
static mode (small jitter motion of less than 1e-3 pixel), a photon noise
limited precision of 3e-5 pixel was reached.
[8]
oai:arXiv.org:1607.07198 [pdf] - 1528119
Collimating Slicer for Optical Integral Field Spectroscopy
Submitted: 2016-07-25
Integral Field Spectroscopy (IFS) is a technique that gives simultaneously
the spectrum of each spatial sampling element in a given object field. It is a
powerful tool which rearranges the data cube (x, y, lambda) represented by two
spatial dimensions defining the field and the spectral decomposition in a
detector plane. In IFS, the spatial unit reorganizes the field and the spectral
unit is being composed of a classical spectrograph.The development of a
Collimating Slicer aims at proposing a new type of integral field spectrograph
which should be more compact. The main idea is to combine the image slicer with
the collimator of the spectrograph, thus mixing the spatial and spectral units.
The traditional combination of slicer, pupil and slit elements and the
spectrograph collimator is replaced by a new one composed of a slicer and
collimator only. In this paper, the state of the art of integral field
spectroscopy using image slicers is described. The new system based onto the
development of a Collimating Slicer for optical integral field spectroscopy is
depicted. First system analysis results and future improvements are discussed.
It finally turns out that this new system looks very promising for low
resolution spectroscopy.
[9]
oai:arXiv.org:1607.02357 [pdf] - 1530987
Optical design of a multi-resolution, single shot spectrograph
Submitted: 2016-07-06
Multi-object or integral field spectrographs are recognized techniques for
achieving simultaneous spectroscopic observations of different or extended sky
objects with a high multiplex factor. In this communication is described a
complementary approach for realizing similar measurements under different
spectral resolutions at the same time. We describe the basic principle of this
new type of spectrometer, that is based on the utilization of an optical pupil
slicer. An optical design inspired from an already studied instrument is then
presented and commented for the sake of illustration. Technical issues about
the pupil slicer and diffractive components are also discussed. We finally
conclude on the potential advantages and drawbacks of the proposed system.
[10]
oai:arXiv.org:1607.01554 [pdf] - 1528099
Analysis of nulling phase functions suitable to image plane coronagraphy
Submitted: 2016-07-06
Coronagraphy is a very efficient technique for identifying and characterizing
extra-solar planets orbiting in the habitable zone of their parent star,
especially when used in a space environment. An important family of
coronagraphs is based on phase plates located at an intermediate image plane of
the optical system, that spread the starlight outside the "Lyot" exit pupil
plane of the instrument. In this communication we present a set of candidate
phase functions generating a central null at the Lyot plane, and study how it
propagates to the image plane of the coronagraph. These functions include
linear azimuthal phase ramps (the well-known optical vortex), azimuthally
cosine-modulated phase profiles, and circular phase gratings. Numerical
simulations of the expected null depth, inner working angle, sensitivity to
pointing errors, effect of central obscuration located at the pupil or image
planes, and effective throughput including image mask and Lyot stop
transmissions are presented and discussed. The preliminary conclusion is that
azimuthal cosine functions appear as an interesting alternative to the
classical optical vortex of integer topological charge.
[11]
oai:arXiv.org:1607.01560 [pdf] - 1530963
Experimental demonstration of a crossed cubes nuller for coronagraphy
and interferometry
Submitted: 2016-07-06
In this communication we present the first experimental results obtained on
the Crossed-cubes nuller (CCN), that is a new type of Achromatic phase shifter
(APS) based on a pair of crossed beamsplitter cubes. We review the general
principle of the CCN, now restricted to two interferometric outputs for
achieving better performance, and describe the experimental apparatus developed
in our laboratory. It is cheap, compact, and easy to align. The results
demonstrate a high extinction rate in monochromatic light and confirm that the
device is insensitive to its polarization state. Finally, the first lessons
from the experiment are summarized and discussed in view of future space
missions searching for extra-solar planets located in the habitable zone,
either based on a coronagraphic telescope or a sparse-aperture nulling
interferometer
[13]
oai:arXiv.org:1407.2719 [pdf] - 1268472
Cheapest nuller in the world: Crossed beamsplitter cubes
Submitted: 2014-07-10, last modified: 2015-08-29
In this communication is described a new type of Achromatic phase shifter
(APS) suitable for both nulling interferometry and coronagraphy, based on a
couple of crossed beamsplitter cubes, well-suited for equipping future
spaceborne instruments searching for extra-solar planets located in a habitable
zone. We present the general principle of this APS and discuss possible
implementations into a nulling coronagraph telescope or into a sparse-aperture
interferometer, either of the Fizeau or Michelson type. Expected performance in
terms of transmission maps and a preliminary tolerance analysis are also
provided. It turns out that the device is cheap, compact, and presents
reasonable manufacturing tolerances and costs
[14]
oai:arXiv.org:1508.07487 [pdf] - 1342821
Fully achromatic nulling interferometer (FANI) for high SNR exoplanet
characterization
Submitted: 2015-08-29
Space-borne nulling interferometers have long been considered as the best
option for searching and characterizing extra-solar planets located in the
habitable zone of their parent stars. Solutions for achieving deep starlight
extinction are now numerous and well demonstrated. However they essentially aim
at realizing an achromatic central null in order to extinguish the star. In
this communication is described a major improvement of the technique, where the
achromatization process is extended to the entire fringe pattern. Therefore
higher Signal-to-noise ratios (SNR) and appreciable simplification of the
detection system should result. The basic principle of this Fully achromatic
nulling interferometer (FANI) consists in inserting dispersive elements along
the arms of the interferometer. Herein this principle is explained and
illustrated by a preliminary optical system design. The typical achievable
performance and limitations are discussed and some initial tolerance
requirements are also provided
[15]
oai:arXiv.org:1508.06555 [pdf] - 1267007
NectarCAM : a camera for the medium size telescopes of the Cherenkov
Telescope Array
Glicenstein, J-F.;
Abril, O.;
Barrio, J-A.;
Blanch~Bigas, O.;
Bolmont, J.;
Bouyjou, F.;
Brun, P.;
Chabanne, E.;
Champion, C.;
Colonges, S.;
Corona, P.;
Delagnes, E.;
Delgado, C.;
Ginzov, C. Diaz;
Durand, D.;
Ernenwein, J-P.;
Fegan, S.;
Ferreira, O.;
Fesquet, M.;
Fiasson, A.;
Fontaine, G.;
Fouque, N.;
Gascon, D.;
Giebels, B.;
Henault, F.;
Hermel, R.;
Hoffmann, D.;
Horan, D.;
Houles, J.;
Jean, P.;
Jocou, L.;
Karkar, S.;
Knoedlseder, J.;
Kossakowski, R.;
Lamanna, G.;
LeFlour, T.;
Lenain, J-P.;
Leveque, A.;
Louis, F.;
Martinez, G.;
Moudden, Y.;
Moulin, E.;
Nayman, P.;
Nunio, F.;
Olive, J-F.;
Panazol, J-L.;
Pavy, S.;
Petrucci, P-O.;
Pierre, E.;
Prast, J.;
Punch, M.;
Ramon, P.;
Rateau, S.;
Ravel, T.;
Rosier-Lees, S.;
Sanuy, A.;
Shayduk, M.;
Sizun, P-Y.;
Sulanke, K-H.;
Tavernet, J-P.;
Tejedor~Alvarez, L-A.;
Toussenel, F.;
Vasileiadis, G.;
Voisin, V.;
Waegebert, V.;
Wischnewski, R.
Submitted: 2015-08-26
NectarCAM is a camera proposed for the medium-sized telescopes of the
Cherenkov Telescope Array (CTA) covering the central energy range of ~100 GeV
to ~30 TeV. It has a modular design and is based on the NECTAr chip, at the
heart of which is a GHz sampling Switched Capacitor Array and a 12-bit Analog
to Digital converter. The camera will be equipped with 265 7-photomultiplier
modules, covering a field of view of 8 degrees. Each module includes the
photomultiplier bases, high voltage supply, pre-amplifier, trigger, readout and
Ethernet transceiver. The recorded events last between a few nanoseconds and
tens of nanoseconds. The camera trigger will be flexible so as to minimize the
read-out dead-time of the NECTAr chips. NectarCAM is designed to sustain a data
rate of more than 4 kHz with less than 5\% dead time. The camera concept, the
design and tests of the various subcomponents and results of thermal and
electrical prototypes are presented. The design includes the mechanical
structure, cooling of the electronics, read-out, clock distribution, slow
control, data-acquisition, triggering, monitoring and services.
[16]
oai:arXiv.org:1407.2720 [pdf] - 1215579
Imaging and nulling properties of sparse-aperture Fizeau interferometers
Submitted: 2014-07-10
In this communication are presented rigorous and approximate analytical
expressions of the Point Spread Function (PSF) and Field of View (FoV)
achievable by multi-aperture Fizeau interferometers, either of the imaging or
nulling types. The described formalism can be helpful for dimensioning future
space missions in search of habitable extra-solar planets. Herein the
characteristics of PSF and FoV are derived from simple analytical expressions
that are further computed numerically in order to evidence the critical role of
pupil re-imaging along the interferometer arms. The formalism is also well
suited to simulating pseudo-images generated by a nulling Fizeau
interferometer, and numerical computations demonstrate that it is only
efficient for very short baselines. Finally, two different designs improving
the nulling capacities of such exoplanet observing instruments are briefly
presented and discussed
[17]
oai:arXiv.org:1407.1387 [pdf] - 1215424
Metrology calibration and very high accuracy centroiding with the NEAT
testbed
Crouzier, A.;
Malbet, F.;
Preis, O.;
Henault, F.;
Kern, P.;
Martin, G.;
Feautrier, P.;
Stadler, E.;
Lafrasse, S.;
Delboulbe, A.;
Behar, E.;
Saint-Pe, M.;
Dupont, J.;
Potin, S.;
Cara, C.;
Donati, M.;
Doumayrou, E.;
Lagage, P. O.;
Léger, A.;
LeDuigou, J. M.;
Shao, M.;
Goullioud, R.
Submitted: 2014-07-05
NEAT is an astrometric mission proposed to ESA with the objectives of
detecting Earth-like exoplanets in the habitable zone of nearby solar-type
stars. NEAT requires the capability to measure stellar centroids at the
precision of 5e-6 pixel. Current state-of-the-art methods for centroid
estimation have reached a precision of about 2e-5 pixel at two times Nyquist
sampling, this was shown at the JPL by the VESTA experiment. A metrology system
was used to calibrate intra and inter pixel quantum efficiency variations in
order to correct pixelation errors. The European part of the NEAT consortium is
building a testbed in vacuum in order to achieve 5e-6 pixel precision for the
centroid estimation. The goal is to provide a proof of concept for the
precision requirement of the NEAT spacecraft.
The testbed consists of two main sub-systems. The first one produces pseudo
stars: a blackbody source is fed into a large core fiber and lights-up a
pinhole mask in the object plane, which is imaged by a mirror on the CCD. The
second sub-system is the metrology, it projects young fringes on the CCD. The
fringes are created by two single mode fibers facing the CCD and fixed on the
mirror. In this paper we present the experiments conducted and the results
obtained since July 2013 when we had the first light on both the metrology and
pseudo stars. We explain the data reduction procedures we used.
[18]
oai:arXiv.org:1309.3448 [pdf] - 1179205
First experimental results of very high accuracy centroiding
measurements for the neat astrometric mission
Crouzier, A.;
Malbet, F.;
Preis, O.;
Henault, F.;
Kern, P.;
Martin, G.;
Feautrier, P.;
Stadler, E.;
Lafrasse, S.;
Delboulbe, A.;
Behar, E.;
Saint-Pe, M.;
Dupont, J.;
Potin, S.;
Cara, C.;
Donati, M.;
Doumayrou, E.;
Lagage, P. O.;
Leger, A.;
LeDuigou, J. M.;
Shao, M.;
Goullioud, R.
Submitted: 2013-09-13, last modified: 2013-09-18
NEAT is an astrometric mission proposed to ESA with the objectives of
detecting Earth-like exoplanets in the habitable zone of nearby solar-type
stars. NEAT requires the capability to measure stellar centroids at the
precision of 5e-6 pixel. Current state-of-the-art methods for centroid
estimation have reached a precision of about 2e-5 pixel at two times Nyquist
sampling, this was shown at the JPL by the VESTA experiment. A metrology system
was used to calibrate intra and inter pixel quantum efficiency variations in
order to correct pixelation errors. The European part of the NEAT consortium is
building a testbed in vacuum in order to achieve 5e-6 pixel precision for the
centroid estimation. The goal is to provide a proof of concept for the
precision requirement of the NEAT spacecraft. In this paper we present the
metrology and the pseudo stellar sources sub-systems, we present a performance
model and an error budget of the experiment and we report the present status of
the demonstration. Finally we also present our first results: the experiment
had its first light in July 2013 and a first set of data was taken in air. The
analysis of this first set of data showed that we can already measure the pixel
positions with an accuracy of about 1e-4 pixel.
[20]
oai:arXiv.org:1307.4545 [pdf] - 1941894
The NectarCAM camera project
Glicenstein, J-F.;
Barcelo, M.;
Barrio, J-A.;
Blanch, O.;
Boix, J.;
Bolmont, J.;
Boutonnet, C.;
Cazaux, S.;
Chabanne, E.;
Champion, C.;
Chateau, F.;
Colonges, S.;
Corona, P.;
Couturier, S.;
Courty, B.;
Delagnes, E.;
Delgado, C.;
Ernenwein, J-P.;
Fegan, S.;
Ferreira, O.;
Fesquet, M.;
Fontaine, G.;
Fouque, N.;
Henault, F.;
Gascón, D.;
Herranz, D.;
Hermel, R.;
Hoffmann, D.;
Houles, J.;
Karkar, S.;
Khelifi, B.;
Knödlseder, J.;
Martinez, G.;
Lacombe, K.;
Lamanna, G.;
LeFlour, T.;
Lopez-Coto, R.;
Louis, F.;
Mathieu, A.;
Moulin, E.;
Nayman, P.;
Nunio, F.;
Olive, J-F.;
Panazol, J-L.;
Petrucci, P-O.;
Punch, M.;
Prast, J.;
Ramon, P.;
Riallot, M.;
Ribó, M.;
Rosier-Lees, S.;
Sanuy, A.;
Siero, J.;
Tavernet, J-P.;
Tejedor, L. A.;
Toussenel, F.;
Vasileiadis, G.;
Voisin, V.;
Waegebert, V.;
Zurbach, C.
Submitted: 2013-07-17
In the framework of the next generation of Cherenkov telescopes, the
Cherenkov Telescope Array (CTA), NectarCAM is a camera designed for the medium
size telescopes covering the central energy range of 100 GeV to 30 TeV.
NectarCAM will be finely pixelated (~ 1800 pixels for a 8 degree field of view,
FoV) in order to image atmospheric Cherenkov showers by measuring the charge
deposited within a few nanoseconds time-window. It will have additional
features like the capacity to record the full waveform with GHz sampling for
every pixel and to measure event times with nanosecond accuracy. An array of a
few tens of medium size telescopes, equipped with NectarCAMs, will achieve up
to a factor of ten improvement in sensitivity over existing instruments in the
energy range of 100 GeV to 10 TeV. The camera is made of roughly 250
independent read-out modules, each composed of seven photo-multipliers, with
their associated high voltage base and control, a read-out board and a
multi-service backplane board. The read-out boards use NECTAr (New Electronics
for the Cherenkov Telescope Array) ASICs which have the dual functionality of
analogue memories and Analogue to Digital Converter (ADC). The camera trigger
to be used will be flexible so as to minimize the read-out dead-time of the
NECTAr chips. We present the camera concept and the design and tests of the
various subcomponents. The design includes the mechanical parts, the cooling of
the electronics, the readout, the data acquisition, the trigger, the monitoring
and services.
[21]
oai:arXiv.org:1208.0099 [pdf] - 719910
An experimental testbed for NEAT to demonstrate micro-pixel accuracy
Crouzier, A.;
Malbet, F.;
Preis, O.;
Henault, F.;
Kern, P.;
Martin, G.;
Feautrier, P.;
Cara, c.;
Lagage, P.;
Leger, A.;
LeDuigou, J. M.;
Shao, M.;
Goullioud, R.
Submitted: 2012-08-01, last modified: 2012-08-30
NEAT is an astrometric mission proposed to ESA with the objectives of
detecting Earth-like exoplanets in the habitable zone of nearby solar-type
stars. In NEAT, one fundamental aspect is the capability to measure stellar
centroids at the precision of 5e-6 pixel. Current state-of-the-art methods for
centroid estimation have reached a precision of about 4e-5 pixel at Nyquist
sampling. Simulations showed that a precision of 2 micro-pixels can be reached,
if intra and inter pixel quantum efficiency variations are calibrated and
corrected for by a metrology system. The European part of the NEAT consortium
is designing and building a testbed in vacuum in order to achieve 5e-6 pixel
precision for the centroid estimation. The goal is to provide a proof of
concept for the precision requirement of the NEAT spacecraft. In this paper we
give the basic relations and trade-offs that come into play for the design of a
centroid testbed and its metrology system. We detail the different conditions
necessary to reach the targeted precision, present the characteristics of our
current design and describe the present status of the demonstration.
[22]
oai:arXiv.org:1109.3131 [pdf] - 1521897
Current results of the PERSEE testbench: the cophasing control and the
polychromatic null rate
Lozi, Julien;
Cassaing, Frederic;
Duigou, Jean-Michel Le;
Sorrente, Beatrice;
Montri, Jospeh;
Reess, Jean-Michel;
Lhome, Emilie;
Buey, Tristan;
Henault, Francois;
Marcotto, Aurelie;
Girard, Paul;
Barillot, Marc;
Ollivier, Marc;
Foresto, Vincent Coude du
Submitted: 2011-09-14
Stabilizing a nulling interferometer at a nanometric level is the key issue
to obtain deep null depths. The PERSEE breadboard has been designed to study
and optimize the operation of a cophased nulling bench in the most realistic
disturbing environment of a space mission. This presentation focuses on the
current results of the PERSEE bench. In terms of metrology, we cophased at 0.33
nm rms for the piston and 80 mas rms for the tip/tilt (0.14% of the Airy disk).
A Linear Quadratic Gaussian (LQG) control coupled with an unsupervised
vibration identification allows us to maintain that level of correction, even
with characteristic vibrations of nulling interferometry space missions. These
performances, with an accurate design and alignment of the bench, currently
lead to a polychromatic unpolarised null depth of 8.9E-6 stabilized at 3E-7 on
the [1.65-2.45] \mum spectral band (37% bandwidth).
[23]
oai:arXiv.org:1107.4626 [pdf] - 1078162
Imaging power of multi-fibered nulling telescopes for extra-solar planet
characterization
Submitted: 2011-07-22
In this paper are discussed the nulling and imaging properties of monolithic
pupil telescopes equipped with a focal plane waveguide array, which could be
envisaged as precursor space missions for future nulling interferometers or
coronagraphs searching for habitable planets outside of our solar system. Three
different concepts of nulling telescopes are reviewed, namely the
Super-Resolving Telescope (SRT) having multiple, non-overlapping exit
sub-apertures and the Sheared-Pupil Telescope (SPT), either unmasked or masked
with a Lyot stop placed at its exit pupil plane. For each case simple
theoretical relationships allowing to estimate the nulling rate,
Signal-to-Noise Ratio (SNR) and Inner Working Angle (IWA) of the telescope are
established or recalled, and numerical simulations are conducted. The
preliminary results of this study show that the most promising designs should
either be a SRT of high radiometric efficiency associated with an adequate
leakage calibration procedure, or a masked SPT with potentially deeper nulling
rates but lower SNR, depending on what kind of performance is to be preferred.
[24]
oai:arXiv.org:1105.2442 [pdf] - 1076574
Phase-shifting technique for improving the imaging capacity of
sparse-aperture optical interferometers
Submitted: 2011-05-12, last modified: 2011-06-24
In this paper, we describe the principle of a multi-aperture interferometer
that uses a phase-shifting technique and is suitable for quick, snapshot
imaging of astrophysical objects at extreme angular resolution through Fourier
inversion. A few advantages of the proposed design are highlighted, among which
are radiometric efficiency, Field of View equivalent to those of Fizeau
interferometers, and a preliminary calibration procedure allowing
characterization of instrumental errors. For large telescope numbers, the
proposed design also results in considerable simplification of the optical and
mechanical design. Numerical simulations suggest that it should be possible to
couple hundreds of telescopes on a single 4K x 4K detector array, using only
conventional optical components or emerging technologies.
[25]
oai:arXiv.org:0904.3888 [pdf] - 1342705
Simple Fourier optics formalism for high angular resolution systems and
nulling interferometry
Submitted: 2009-04-24, last modified: 2009-08-27
In this paper are reviewed various designs of advanced, multi-aperture
optical systems dedicated to high angular resolution imaging or to the
detection of exo-planets by nulling interferometry. A simple Fourier optics
formalism applicable to both imaging arrays and nulling interferometers is
presented, allowing to derive their basic theoretical relationships as
convolution or cross correlation products suitable for fast and accurate
computation. Several unusual designs, such as a super-resolving telescope
utilizing a mosaicking observation procedure or a free-flying, axially
recombined interferometer are examined, and their performance in terms of
imaging and nulling capacity are assessed. In all considered cases, it is found
that the limiting parameter is the diameter of the individual telescopes. The
entire study is only valid in the frame of first-order geometrical optics and
scalar diffraction theory. Furthermore, it is assumed that all entrance
sub-apertures are optically conjugated with their associated exit pupils, a
particularity inducing an instrumental behavior comparable with those of
diffraction gratings.
[26]
oai:arXiv.org:0908.4040 [pdf] - 1017265
Multi-spectral piston sensor for co-phasing giant segmented mirrors and
multi-aperture interferometric arrays
Submitted: 2009-08-27
This paper presents the optical design of a multi-spectral piston sensor
suitable to co-phasing giant segmented mirrors equipping the Future Extremely
Large Telescopes (ELTs). The general theory of the sensor is described in
detail and numerical simulations have been carried out, demonstrating that
direct piston and tip-tilt measurements are feasible within accuracies
respectively close to 20 nm and 10 nano-radians. Those values are compatible
with the co-phasing requirements, although the method seems to be perturbed by
uncorrected atmospheric seeing
[27]
oai:arXiv.org:0808.4107 [pdf] - 359442
Telescope interferometers: an alternative to classical wavefront sensors
Submitted: 2008-08-29
Several types of Wavefront Sensors (WFS) are nowadays available in the field
of Adaptive Optics (AO). Generally speaking, their basic principle consists in
measuring slopes or curvatures of Wavefront Errors (WFE) transmitted by a
telescope, subsequently reconstructing WFEs digitally. Such process, however,
does not seem to be well suited for evaluating co-phasing or piston errors of
future large segmented telescopes in quasi real-time. This communication
presents an original, recently proposed technique for direct WFE sensing. The
principle of the device, which is named "Telescope-Interferometer" (TI), is
based on the addition of a reference optical arm into the telescope pupil
plane. Then incident WFEs are deduced from Point Spread Function (PSF)
measurements at the telescope focal plane. Herein are described two different
types of TIs, and their performance are discussed in terms of intrinsic
measurement accuracy and spatial resolution. Various error sources are studied
by means of numerical simulations, among which photon noise sounds the most
critical. Those computations finally help to define the application range of
the TI method in an AO regime, including main and auxiliary telescope diameters
and magnitude of the guide star. Some practical examples of optical
configurations are also described and commented.
[28]
oai:arXiv.org:0802.2054 [pdf] - 403877
Computing extinction maps of star nulling interferometers
Submitted: 2008-02-14
Herein is discussed the performance of spaceborne nulling interferometers
searching for extra-solar planets, in terms of their extinction maps projected
on-sky. In particular, it is shown that the designs of Spatial Filtering (SF)
and Achromatic Phase Shifter (APS) subsystems, both required to achieve planet
detection and characterization, can sensibly affect the nulling maps produced
by a simple Bracewell interferometer. Analytical relationships involving cross
correlation products are provided and numerical simulations are performed,
demonstrating marked differences in the aspect of extinction maps and the
values of attained fringes contrasts. It is concluded that depending on their
basic principles and designs, FS and APS will result in variable capacities for
serendipitous discoveries of planets orbiting around their parent star. The
mathematical relationships presented in this paper are assumed to be general,
i.e. they should apply to other types of multi-apertures nulling
interferometers.
[29]
oai:arXiv.org:0802.2051 [pdf] - 359439
Signal-to-noise ratio of phase sensing telescope interferometers
Submitted: 2008-02-14
This paper is the third part of a trilogy dealing with the principles,
performance and limitations of what I named "Telescope-Interferometers" (TIs).
The basic idea consists in transforming one telescope into a Wavefront Error
(WFE) sensing device. This can be achieved in two different ways, namely the
off axis and phase-shifting TIs. In both cases the Point-Spread Function (PSF)
measured in the focal plane of the telescope carries information about the
transmitted WFE, which is retrieved by fast and simple algorithms suitable to
an Adaptive Optics (AO) regime. Herein are evaluated the uncertainties of both
types of TIs, in terms of noise and systematic errors. Numerical models are
developed in order to establish the dependence of driving parameters such as
useful spectral range, angular size of the observed star, or detector noise on
the total WFE measurement error. The latter is found particularly sensitive to
photon noise, which rapidly governs the achieved accuracy for telescope
diameters higher than 10 m. We study a few practical examples, showing that TI
method is applicable to AO systems on telescope diameters ranging from 10 to 50
m, depending on seeing conditions and magnitude of the observed stars. We also
discuss the case of a space-borne coronagraph where TI technique provides high
sampling of the input WFE map.
[30]
oai:arXiv.org:physics/0511231 [pdf] - 361077
Conceptual design of a phase shifting telescope-interferometer
Submitted: 2005-11-28
This paper deals with the theoretical principle and optical design of a
phase-shifting telescope-interferometer. What is called a
"Telescope-Interferometer" (T-I) is indeed a novel, recently proposed Wavefront
Error (WFE) sensing technique, whose basic idea consists in combining the main
pupil of a telescope with a second, off-axis reference arm. Then a weak
modulation of the Point Spread Function (PSF) is generated at the focal plane,
allowing for direct phase measurements. We propose a notable improvement of the
method, inspired from classical principles of phase shifting interferometry.
Herein are presented the alternative principle and its achievable measurement
accuracy. The technique shows high performance excepted on narrow areas located
near the pupil boundary. It is applicable to both ground or space telescopes
and is suitable for the co-phasing of segmented mirrors, which is of prime
importance in view of future giant telescope projects.
[31]
oai:arXiv.org:physics/0510226 [pdf] - 361076
An analysis of stellar interferometers as wavefront sensors
Submitted: 2005-10-25
This paper presents the basic principle and theoretical relationships of an
original method allowing to retrieve the Wavefront Errors (WFE) of a ground or
space-borne telescope when combining its main pupil with a second, decentered
reference optical arm. The measurement accuracy of such a
"telescope-interferometer" is then estimated by means of various numerical
simulations, demonstrating a high performance excepted on limited areas near
the telescope pupil rim. In particular, it allows direct phase evaluation (thus
avoiding the use of first or second-order derivatives), which is of special
interest for the co-phasing of segmented mirrors in future giant telescopes
projects. We finally define the useful practical domain of the method, which
seems to be better suited for periodical diagnostics of space or ground based
telescopes, or to real-time scientific observations in some very specific cases
(e.g. the central star in extrasolar planets searching instruments).
[32]
oai:arXiv.org:physics/0510224 [pdf] - 363383
Wavefront sensor based on varying transmission filters: theory and
expected performance
Submitted: 2005-10-25
The use of Wavefront Sensors (WFS) is nowadays fundamental in the field of
instrumental optics. This paper discusses the principle of an original and
recently proposed new class of WFS. Their principle consists in evaluating the
slopes of the wavefront errors by means of varying density filters placed into
the image plane of the tested optical system. The device, sometimes called
'optical differentiation WFS' is completed by a digital data-processing system
reconstructing the wavefront from the obtained slopes. Various luminous sources
of different wavelengths and spectral widths can be employed. The capacities of
the method are discussed from the geometrical and Fourier optics points of
view, then by means of numerical simulations showing that the ultimate accuracy
can be well below lambda/10 and lambda/100 Peak-to-Valley (PTV) and RMS
respectively, provided that certain precautions are taken.
