Note: This is a revised version of the paper that _corrects_a_calculation_error in translating observed Jansky units to EIRP in Watts. Mistakes are labeled below. Motivated by the hypothesis that Oumuamua could conceivably be an interstellar probe, we used the Allen Telescope Array to search for radio transmissions that would indicate a non-natural origin for this object. Observations were made at radio frequencies between 1 and 10 GHz using the Array's correlator receiver with a channel bandwidth of 100 kHz. In frequency regions not corrupted by man-made interference, we find no signal flux with frequency-dependent lower limits of 0.01 Jy at 1 GHz and 0.1 Jy at 7 GHz. For a putative isotropic object, these limits correspond to transmitter powers of (was mistakenly 30 mW) 10 W and (was mistakenly 300 mW) 100 W, respectively. In frequency ranges that are heavily utilized for satellite communications, our sensitivity to weak signals is badly impinged, but we can still place an upper limit of (was mistakenly 10 W) 3 kW for a transmitter on the asteroid. For comparison and validation should a transmitter be discovered, contemporaneous measurements were made on the solar system asteroids 2017 UZ and 2017 WC with comparable sensitivities. Because they are closer to Earth, we place upper limits on transmitter power to be 0.1 and 0.001 times the limits for Oumuamua, respectively.

We apply classical machine vision and machine deep learning methods to prototype signal classifiers for the search for extraterrestrial intelligence. Our novel approach uses two-dimensional spectrograms of measured and simulated radio signals bearing the imprint of a technological origin. The studies are performed using archived narrow-band signal data captured from real-time SETI observations with the Allen Telescope Array and a set of digitally simulated signals designed to mimic real observed signals. By treating the 2D spectrogram as an image, we show that high quality parametric and non-parametric classifiers based on automated visual analysis can achieve high levels of discrimination and accuracy, as well as low false-positive rates. The (real) archived data were subjected to numerous feature-extraction algorithms based on the vertical and horizontal image moments and Huff transforms to simulate feature rotation. The most successful algorithm used a two-step process where the image was first filtered with a rotation, scale and shift-invariant affine transform followed by a simple correlation with a previously defined set of labeled prototype examples. The real data often contained multiple signals and signal ghosts, so we performed our non-parametric evaluation using a simpler and more controlled dataset produced by simulation of complex-valued voltage data with properties similar to the observed prototypes. The most successful non-parametric classifier employed a wide residual (convolutional) neural network based on pre-existing classifiers in current use for object detection in ordinary photographs. These results are relevant to a wide variety of research domains that already employ spectrogram analysis from time-domain astronomy to observations of earthquakes to animal vocalization analysis.

We report a novel radio autocorrelation (AC) search for extraterrestrial intelligence (SETI). For selected frequencies across the terrestrial microwave window (1-10 GHz) observations were conducted at the Allen Telescope Array to identify artificial non-sinusoidal periodic signals with radio bandwidths greater than 4 Hz, which are capable of carrying substantial messages with symbol-rates from 4-1000000 Hz. Out of 243 observations, about half (101) were directed toward sources with known continuum flux > ~1 Jy over the sampled bandwidth (quasars, pulsars, supernova remnants, and masers), based on the hypothesis that they might harbor heretofore undiscovered natural or artificial, repetitive, phase or frequency modulation. The rest of the targets were mostly toward exoplanet stars with no previously discovered continuum flux. No signals attributable to extraterrestrial technology were found in this study. We conclude that the maximum probability that future observations like the ones described here will reveal repetitively modulated emissions is less than 1% for continuum sources and exoplanets, alike. The paper concludes by describing a new approach to expanding this survey to many more targets and much greater sensitivity using archived data from interferometers all over the world.

We describe a new approach and algorithm for the detection of artificial signals and their classification in the search for extraterrestrial intelligence (SETI). The characteristics of radio signals observed during SETI research are often most apparent when those signals are represented as spectrograms. Additionally, many observed signals tend to share the same characteristics, allowing for sorting of the signals into different classes. For this work, complex-valued time-series data were simulated to produce a corpus of 140,000 signals from seven different signal classes. A wide residual neural network was then trained to classify these signal types using the gray-scale 2D spectrogram representation of those signals. An average $F_1$ score of 95.11\% was attained when tested on previously unobserved simulated signals. We also report on the performance of the model across a range of signal amplitudes.

We present a photometric detection of the first brightness dips of the unique variable star KIC 8462852 since the end of the Kepler space mission in 2013 May. Our regular photometric surveillance started in October 2015, and a sequence of dipping began in 2017 May continuing on through the end of 2017, when the star was no longer visible from Earth. We distinguish four main 1-2.5% dips, named "Elsie," "Celeste," "Skara Brae," and "Angkor", which persist on timescales from several days to weeks. Our main results so far are: (i) there are no apparent changes of the stellar spectrum or polarization during the dips; (ii) the multiband photometry of the dips shows differential reddening favoring non-grey extinction. Therefore, our data are inconsistent with dip models that invoke optically thick material, but rather they are in-line with predictions for an occulter consisting primarily of ordinary dust, where much of the material must be optically thin with a size scale <<1um, and may also be consistent with models invoking variations intrinsic to the stellar photosphere. Notably, our data do not place constraints on the color of the longer-term "secular" dimming, which may be caused by independent processes, or probe different regimes of a single process.

We have developed a new generation of low noise, broadband feeds for the Allen Telescope Array at the Hat Creek Observatory in Northern California. The new feeds operate over the frequency range 0.9 to 14 GHz. The noise temperatures of the feeds have been substantially improved by cooling the entire feed structure as well as the low noise amplifiers to 70 K. To achieve this improved performance, the new feeds are mounted in glass vacuum bottles with plastic lenses that maximize the microwave transmission through the bottles. Both the cooled feeds and their low noise amplifiers produce total system temperatures that are in the range 25-30 K from 1 GHz to 5 GHz and 40-50 K up to 12.5 GHz.

We report radio SETI observations on a large number of known exoplanets and other nearby star systems using the Allen Telescope Array (ATA). Observations were made over about 19000 hours from May 2009 to Dec 2015. This search focused on narrow-band radio signals from a set totaling 9293 stars, including 2015 exoplanet stars and Kepler objects of interest and an additional 65 whose planets may be close to their Habitable Zone. The ATA observations were made using multiple synthesized beams and an anticoincidence filter to help identify terrestrial radio interference. Stars were observed over frequencies from 1- 9 GHz in multiple bands that avoid strong terrestrial communication frequencies. Data were processed in near-real time for narrow-band (0.7- 100 Hz) continuous and pulsed signals, with transmitter/receiver relative accelerations from -0.3 to 0.3 m/s^2. A total of 1.9 x 10^8 unique signals requiring immediate follow-up were detected in observations covering more than 8 x 10^6 star-MHz. We detected no persistent signals from extraterrestrial technology exceeding our frequency-dependent sensitivity threshold of 180 - 310 x 10^-26 W / m^2.

We report on a search for the presence of signals from extraterrestrial intelligence in the direction of the star system KIC 8462852. Observations were made at radio frequencies between 1-10 GHz using the Allen Telescope Array. No narrowband radio signals were found at a level of 180-300 Jy in a 1 Hz channel, or medium band signals above 10 Jy in a 100 kHz channel.

In the cm-wavelength range, an extraterrestrial electromagnetic narrow band (sine wave) beacon is an excellent choice to get alien attention across interstellar distances because 1) it is not strongly affected by interstellar / interplanetary dispersion or scattering, and 2) searching for narrowband signals is computationally efficient (scales as Ns log(Ns) where Ns = number of voltage samples). Here we consider a special case wideband signal where two or more delayed copies of the same signal are transmitted over the same frequency and bandwidth, with the result that ISM dispersion and scattering cancel out during the detection stage. Such a signal is both a good beacon (easy to find) and carries arbitrarily large information rate (limited only by the atmospheric transparency to about 10 GHz). The discovery process uses an autocorrelation algorithm, and we outline a compute scheme where the beacon discovery search can be accomplished with only 2x the processing of a conventional sine wave search, and discuss signal to background response for sighting the beacon. Once the beacon is discovered, the focus turns to information extraction. Information extraction requires similar processing as for generic wideband signal searches, but since we have already identified the beacon, the efficiency of information extraction is negligible.

The Allen Telescope Array is a multi-user instrument and will perform simultaneous radio astronomy and radio SETI (search for extra-terrestrial intelligence) observations. It is a multi-beam instrument, with 16 independently steerable dual-polarization beams at 4 different tunings. Given 4 beams at one tuning, it is possible to distinguish RFI from true ETI signals by pointing the beams in different directions. Any signal that appears in more than one beam can be identified as RFI and ignored during SETI. We discuss the effectiveness of this approach for RFI rejection using realistic simulations of the fully populated 350 element configuration of the ATA as well as the interim 32 element configuration. Over a 5 minute integration period, we find RFI rejection ratios exceeding 50 dB over most of the sky.

One of the exciting prospects for large N arrays is the potential for custom beam forming when operating in phased array mode. Pattern nulls may be generated by properly weighting the signals from all antennas with only minor degradation of gain in the main beam. Here we explore the limits of beam shape manipulation using the parameters of the Allen Telescope Array. To generate antenna weights, we apply an iterative method that is particularly easy to understand yet is comparable to linearly-constrained methods. In particular, this method elucidates how narrow band nulls may be extended to wider bandwidth. In practical RFI mitigation, the gain in the synthetic beam is obviously affected by the number and bandwidth of nulls placed elsewhere. Here we show how to predict the impact of a set of nulls in terms of the area of sky covered and null bandwidth. Most critical for design of the ATA, we find that high-speed (~10 ms) amplitude control of each array element over the full range 0-1 is critically important to allow testing of wide area / wide bandwidth nulling.

The Allen Telescope Array (ATA) is a cm-wave interferometer in California, comprising 42 antenna elements with 6-m diameter dishes. We characterize the antenna optical accuracy using two-antenna interferometry and radio holography. The distortion of each telescope relative to the average is small, with RMS differences of 1 percent of beam peak value. Holography provides images of dish illumination pattern, allowing characterization of as-built mirror surfaces. The ATA dishes can experience mm-scale distortions across -2 meter lengths due to mounting stresses or solar radiation. Experimental RMS errors are 0.7 mm at night and 3 mm under worst case solar illumination. For frequencies 4, 10, and 15 GHz, the nighttime values indicate sensitivity losses of 1, 10 and 20 percent, respectively. The ATA.s exceptional wide-bandwidth permits observations over a continuous range 0.5 to 11.2 GHz, and future retrofits may increase this range to 15 GHz. Beam patterns show a slowly varying focus frequency dependence. We probe the antenna optical gain and beam pattern stability as a function of focus and observation frequency, concluding that ATA can produce high fidelity images over a decade of simultaneous observation frequencies. In the day, the antenna sensitivity and pointing accuracy are affected. We find that at frequencies greater than 5 GHz, daytime observations greater than 5 GHz will suffer some sensitivity loss and it may be necessary to make antenna pointing corrections on a 1 to 2 hourly basis.

As a new generation radio telescope, the Allen Telescope Array (ATA) is a prototype for the square kilometer array (SKA). Here we describe recently developed design constraints for the ATA digital signal processing chain as a case study for SKA processing. As radio frequency interference (RFI) becomes increasingly problematical for radio astronomy, radio telescopes must support a wide range of RFI mitigation strategies including online adaptive RFI nulling. We observe that the requirements for digital accuracy and control speed are not driven by astronomical imaging but by RFI. This can be understood from the fact that high dynamic range and digital precision is necessary to remove strong RFI signals from the weak astronomical background, and because RFI signals may change rapidly compared with celestial sources. We review and critique lines of reasoning that lead us to some of the design specifications for ATA digital processing, including these: beamformer coefficients must be specified with at least 1{\deg} precision and at least once per millisecond to enable flexible RFI excision.

The Allen Telescope Array (ATA) is a Large-Number-Small-Diameter radio telescope array currently with 42 individual antennas and 5 independent back-end science systems (2 imaging FX correlators and 3 time domain beam formers) located at the Hat Creek Radio Observatory (HCRO). The goal of the ATA is to run multiple back-ends simultaneously, supporting multiple science projects commensally. The primary software control systems are based on a combination of Java, JRuby and Ruby on Rails. The primary control API is simplified to provide easy integration with new back-end systems while the lower layers of the software stack are handled by a master observing system. Scheduling observations for the ATA is based on finding a union between the science needs of multiple projects and automatically determining an efficient path to operating the various sub-components to meet those needs. When completed, the ATA is expected to be a world-class radio telescope, combining dedicated SETI projects with numerous radio astronomy science projects.

The Pi GHz Sky Survey (PiGSS) is a key project of the Allen Telescope Array. PiGSS is a 3.1 GHz survey of radio continuum emission in the extragalactic sky with an emphasis on synoptic observations that measure the static and time-variable properties of the sky. During the 2.5-year campaign, PiGSS will twice observe ~250,000 radio sources in the 10,000 deg^2 region of the sky with b > 30 deg to an rms sensitivity of ~1 mJy. Additionally, sub-regions of the sky will be observed multiple times to characterize variability on time scales of days to years. We present here observations of a 10 deg^2 region in the Bootes constellation overlapping the NOAO Deep Wide Field Survey field. The PiGSS image was constructed from 75 daily observations distributed over a 4-month period and has an rms flux density between 200 and 250 microJy. This represents a deeper image by a factor of 4 to 8 than we will achieve over the entire 10,000 deg^2. We provide flux densities, source sizes, and spectral indices for the 425 sources detected in the image. We identify ~100$ new flat spectrum radio sources; we project that when completed PiGSS will identify 10^4 flat spectrum sources. We identify one source that is a possible transient radio source. This survey provides new limits on faint radio transients and variables with characteristic durations of months.

We present the Allen Telescope Array Twenty-centimeter Survey (ATATS), a multi-epoch (12 visits), 690 square degree radio image and catalog at 1.4GHz. The survey is designed to detect rare, very bright transients as well as to verify the capabilities of the ATA to form large mosaics. The combined image using data from all 12 ATATS epochs has RMS noise sigma = 3.94mJy / beam and dynamic range 180, with a circular beam of 150 arcsec FWHM. It contains 4408 sources to a limiting sensitivity of S = 20 mJy / beam. We compare the catalog generated from this 12-epoch combined image to the NRAO VLA Sky Survey (NVSS), a legacy survey at the same frequency, and find that we can measure source positions to better than ~20 arcsec. For sources above the ATATS completeness limit, the median flux density is 97% of the median value for matched NVSS sources, indicative of an accurate overall flux calibration. We examine the effects of source confusion due to the effects of differing resolution between ATATS and NVSS on our ability to compare flux densities. We detect no transients at flux densities greater than 40 mJy in comparison with NVSS, and place a 2-sigma upper limit on the transient rate for such sources of 0.004 per square degree. These results suggest that the > 1 Jy transients reported by Matsumura et al. (2009) may not be true transients, but rather variable sources at their flux density threshold.

The first 42 elements of the Allen Telescope Array (ATA-42) are beginning to deliver data at the Hat Creek Radio Observatory in Northern California. Scientists and engineers are actively exploiting all of the flexibility designed into this innovative instrument for simultaneously conducting surveys of the astrophysical sky and conducting searches for distant technological civilizations. This paper summarizes the design elements of the ATA, the cost savings made possible by the use of COTS components, and the cost/performance trades that eventually enabled this first snapshot radio camera. The fundamental scientific program of this new telescope is varied and exciting; some of the first astronomical results will be discussed.