V1180 Cas is a young variable that has shown strong photometric fluctuations (Delta_I~6mag) in the recent past, which have been attributed to events of enhanced accretion. The source has entered a new high-brightness state in Sept.2013, which we have previously analyzed through optical and near-IR spectroscopy. To investigate the current active phase of V1180 Cas, we performed observations with the Chandra satellite to study the X-ray emission from the object and its connection to accretion episodes. Chandra observations were performed in early Aug.2014. Complementary JHK photometry and J-band spectra were taken at our Campo Imperatore facility to relate the X-ray and near-IR emission from the target. We observe a peak of X-ray emission at the nominal position of V1180 Cas. This signal corresponds to an X-ray luminosity L_X(0.5-7 kev) in the range 0.8-2.2e30 erg/s. Based on the relatively short duration of the dim states in the light curve and on stellar luminosity considerations, we explored the possibility that the brightness minima of V1180 Cas are driven by extinction variations. From the analysis of the spectral energy distribution of the high state we infer a stellar luminosity of 0.8-0.9 Lsun and find that the derived L_X is comparable to the average X-ray luminosities of T Tauri stars. Moreover, the X-ray luminosity is lower than the X-ray emission levels of 5e30 -1e31 erg/s detected at outbursts in similar low-mass objects. Our analysis suggests that at least part of the photometric fluctuations of V1180 Cas might be extinction effects rather than the result of accretion excess emission. However, as the source displays spectral features indicative of active accretion, we speculate that its photometric variations might be the result of a combination of accretion-induced and extinction-driven effects, as suggested for other young variables, such as V1184 Tau and V2492 Cyg.

During the On-Station Thermal Test campaign of the LISA Pathfinder the data and diagnostics subsystem was tested in nearly space conditions for the first time after integration in the satellite. The results showed the compliance of the temperature measurement system, obtaining temperature noise around $10^{-4}\,{\rm K}\, {\rm Hz}^{-1/2}$ in the frequency band of $1-30\;{\rm mHz}$. In addition, controlled injection of heat signals to the suspension struts anchoring the LISA Technology Package (LTP) Core Assembly to the satellite structure allowed to experimentally estimate for the first time the phase noise contribution through thermo-elastic distortion of the LTP interferometer, the satellite's main instrument. Such contribution was found to be at $10^{-12}\,{\rm m}\, {\rm Hz}^{-1/2}$, a factor of 30 below the measured noise at the lower end of the measurement bandwidth ($1\,{\rm mHz}$).

LISA Pathfinder is a technology demonstration mission for the Laser Interferometer Space Antenna (LISA). The main experiment on-board LISA Pathfinder is the so-called LISA Technology Package (LTP) which has the aim to measure the differential acceleration between two free-falling test masses with an accuracy of 3x10^(-14) ms^(-2)/sqrt[Hz] between 1 mHz and 30 mHz. This measurement is performed interferometrically by the Optical Metrology System (OMS) on-board LISA Pathfinder. In this paper we present the development of an experimental end-to-end testbed of the entire OMS. It includes the interferometer and its sub-units, the interferometer back-end which is a phasemeter and the processing of the phasemeter output data. Furthermore, 3-axes piezo actuated mirrors are used instead of the free-falling test masses for the characterisation of the dynamic behaviour of the system and some parts of the Drag-free and Attitude Control System (DFACS) which controls the test masses and the satellite. The end-to-end testbed includes all parts of the LTP that can reasonably be tested on earth without free-falling test masses. At its present status it consists mainly of breadboard components. Some of those have already been replaced by Engineering Models of the LTP experiment. In the next steps, further Engineering Models and Flight Models will also be inserted in this testbed and tested against well characterised breadboard components. The presented testbed is an important reference for the unit tests and can also be used for validation of the on-board experiment during the mission.