The Spectral Imaging of the Coronal Environment (SPICE) instrument is a high-resolution imaging spectrometer operating at extreme ultraviolet (EUV) wavelengths. In this paper, we present the concept, design, and pre-launch performance of this facility instrument on the ESA/NASA Solar Orbiter mission. The goal of this paper is to give prospective users a better understanding of the possible types of observations, the data acquisition, and the sources that contribute to the instrument's signal. The paper discusses the science objectives, with a focus on the SPICE-specific aspects, before presenting the instrument's design, including optical, mechanical, thermal, and electronics aspects. This is followed by a characterisation and calibration of the instrument's performance. The paper concludes with descriptions of the operations concept and data processing. The performance measurements of the various instrument parameters meet the requirements derived from the mission's science objectives. The SPICE instrument is ready to perform measurements that will provide vital contributions to the scientific success of the Solar Orbiter mission.

Standing slow-mode waves have been recently observed in flaring loops by the Atmospheric Imaging Assembly (AIA) of the Solar Dynamics Observatory (SDO). By means of the coronal seismology technique transport coefficients in hot ($\sim$10 MK) plasma were determined by Wang et al.(2015, Paper I), revealing that thermal conductivity is nearly suppressed and compressive viscosity is enhanced by more than an order of magnitude. In this study we use 1D nonlinear MHD simulations to validate the predicted results from the linear theory and investigate the standing slow-mode wave excitation mechanism. We first explore the wave trigger based on the magnetic field extrapolation and flare emission features. Using a flow pulse driven at one footpoint we simulate the wave excitation in two types of loop models: model 1 with the classical transport coefficients and model 2 with the seismology-determined transport coefficients. We find that model 2 can form the standing wave pattern (within about one period) from initial propagating disturbances much faster than model 1, in better agreement with the observations. Simulations of the harmonic waves and the Fourier decomposition analysis show that the scaling law between damping time ($\tau$) and wave period ($P$) follows $\tau\propto{P^2}$ in model 2, while $\tau\propto{P}$ in model 1. This indicates that the largely enhanced viscosity efficiently increases the dissipation of higher harmonic components, favoring the quick formation of the fundamental standing mode. Our study suggests that observational constraints on the transport coefficients are important in understanding both, the wave excitation and damping mechanisms.

We have reported previously on a new method we are developing for using image-based information to improve global coronal magnetic field models. In that work we presented early tests of the method which proved its capability to improve global models based on flawed synoptic magnetograms, given excellent constraints on the field in the model volume. In this follow-up paper we present the results of similar tests given field constraints of a nature that could realistically be obtained from quality white-light coronagraph images of the lower corona. We pay particular attention to difficulties associated with the line-of-sight projection of features outside of the assumed coronagraph image plane, and the effect on the outcome of the optimization of errors in localization of constraints. We find that substantial improvement in the model field can be achieved with this type of constraints, even when magnetic features in the images are located outside of the image plane.

The analysis of a hot loop oscillation event using SOHO/SUMER, GOES/SXI, and RHESSI observations is presented. Damped Doppler shift oscillations were detected in the Fe XIX line by SUMER, and interpreted as a fundamental standing slow mode. The evolution of soft X-ray emission from GOES/SXI and hard X-ray sources from RHESSI suggests that the oscillations of a large loop are triggered by a small flare, which may be produced by interaction (local reconnection) of this large loop with a small loop at its footpoint. This study provides clear evidence supporting our early conjecture that the slow-mode standing waves in hot coronal loops are excited by impulsive heating (small or microflares) at the loop's footpoint.

Three dimensional electron density distributions in the solar corona are reconstructed for 100 Carrington Rotations (CR 2054$-$2153) during 2007/03$-$2014/08 using the spherically symmetric method from polarized white-light observations with the STEREO/COR1. These three-dimensional electron density distributions are validated by comparison with similar density models derived using other methods such as tomography and a MHD model as well as using data from SOHO/LASCO-C2. Uncertainties in the estimated total mass of the global corona are analyzed based on differences between the density distributions for COR1-A and -B. Long-term variations of coronal activity in terms of the global and hemispheric average electron densities (equivalent to the total coronal mass) reveal a hemispheric asymmetry during the rising phase of Solar Cycle 24, with the northern hemisphere leading the southern hemisphere by a phase shift of 7$-$9 months. Using 14-CR (~13-month) running averages, the amplitudes of the variation in average electron density between Cycle 24 maximum and Cycle 23/24 minimum (called the modulation factors) are found to be in the range of 1.6$-$4.3. These modulation factors are latitudinally dependent, being largest in polar regions and smallest in the equatorial region. These modulation factors also show a hemispheric asymmetry, being somewhat larger in the southern hemisphere. The wavelet analysis shows that the short-term quasi-periodic oscillations during the rising and maximum phases of Cycle 24 have a dominant period of 7$-$8 months. In addition, it is found that the radial distribution of mean electron density for streamers at Cycle 24 maximum is only slightly larger (by ~30%) than at cycle minimum.

The coronal magnetic field directly or indirectly affects a majority of the phenomena studied in space physics. It provides energy for coronal heating, controls the release of coronal mass ejections (CMEs), and drives heliospheric and magnetospheric activity, yet the coronal magnetic field itself has proven difficult to measure. This difficulty has prompted a decades-long effort to develop accurate, timely, models of the field - an effort that continues today. We have developed a method for improving global coronal magnetic field models by incorporating the type of morphological constraints which could be derived from coronal images. Here we report promising initial tests of this approach on two theoretical problems, and discuss opportunities for application.

Slow magnetoacoustic waves were first detected in hot ($>$6 MK) flare loops by the SOHO/SUMER spectrometer as Doppler shift oscillations in Fe XIX and Fe XXI lines. Recently, such longitudinal waves have been found by SDO/AIA in the 94 and 131 \AA\ channels. Wang et al. (2015) reported the first AIA event revealing signatures in agreement with a fundamental standing slow-mode wave, and found quantitative evidence for thermal conduction suppression from the temperature and density perturbations in the hot loop plasma of $\gtrsim$ 9 MK. The present study extends the work of Wang et al. (2015) by using an alternative approach. We determine the polytropic index directly based on the polytropic assumption instead of invoking the linear approximation. The same results are obtained as in the linear approximation, indicating that the nonlinearity effect is negligible. We find that the flare loop cools slower (by a factor of 2-4) than expected from the classical Spitzer conductive cooling, approximately consistent with the result of conduction suppression obtained from the wave analysis. The modified Spitzer cooling timescales based on the nonlocal conduction approximation are consistent with the observed, suggesting that nonlocal conduction may account for the observed conduction suppression in this event. In addition, the conduction suppression mechanism predicts that larger flares may tend to be hotter than expected by the EM-$T$ relation derived by Shibata & Yokoyama (2002)

Analysis of a longitudinal wave event observed by the Atmospheric Imaging Assembly (AIA) onboard the Solar Dynamics Observatory (SDO) is presented. A time sequence of 131 A images reveals that a C-class flare occurred at one footpoint of a large loop and triggered an intensity disturbance (enhancement) propagating along it. The spatial features and temporal evolution suggest that a fundamental standing slow-mode wave could be set up quickly after meeting of two initial disturbances from the opposite footpoints. The oscillations have a period of ~12 min and a decay time of ~9 min. The measured phase speed of 500$\pm$50 km/s matches the sound speed in the heated loop of ~10 MK, confirming that the observed waves are of slow mode. We derive the time-dependent temperature and electron density wave signals from six AIA extreme-ultraviolet (EUV) channels, and find that they are nearly in phase.The measured polytropic index from the temperature and density perturbations is 1.64$\pm$0.08 close to the adiabatic index of 5/3 for an ideal monatomic gas. The interpretation based on a 1D linear MHD model suggests that the thermal conductivity is suppressed by at least a factor of 3 in the hot flare loop at 9 MK and above. The viscosity coefficient is determined by coronal seismology from the observed wave when only considering the compressive viscosity dissipation. We find that to interpret the rapid wave damping, the classical compressive viscosity coefficient needs to be enhanced by a factor of 15 as the upper limit.

The analysis of multiwavelength properties of propagating disturbances (PDs) using Hinode/EIS observations is presented. Quasi-periodic PDs were mostly interpreted as slow magnetoacoustic waves in early studies, but recently suggested to be intermittent upflows of the order of 50-150 km/s based on the Red-Blue (RB) asymmetry analysis of spectral line profiles. Using the forward models, velocities of the secondary component derived from the RB analysis are found significantly overestimated due to the saturation effect when its offset velocities are smaller than the Gaussian width. We developed a different method to examine spectral features of the PDs. This method is assuming that the excessive emission of the PD profile against the background (taken as that prior to the PD) is caused by a hypothetic upflow. The derived LOS velocities of the flow are on the order of 10-30 km/s from the warm (1-1.5 MK) coronal lines, much smaller than those inferred from the RB analysis. This result does not support the flow interpretation but favors of the early wave interpretation.

We present a study of the 2014 January 6 solar energetic particle (SEP) event, which produced a small ground level enhancement (GLE), making it the second GLE of this unusual solar cycle 24. This event was primarily observed by the South Pole neutron monitors (increase of ~2.5%) whereas a few other neutron monitors recorded smaller increases. The associated coronal mass ejection (CME) originated behind the western limb and had the speed of 1960 km/s. The height of the CME at the start of the associated metric type II radio burst, which indicates the formation of a strong shock, was measured to be 1.61 Rs using a direct image from STEREO-A/EUVI. The CME height at the time of GLE particle release (determined using the South Pole neutron monitor data) was directly measured as 2.96 Rs, from the STEREO-A/COR1 white-light observations. These CME heights are consistent with those obtained for the GLE71, the only other GLE of the current cycle as well as cycle-23 GLEs derived using back-extrapolation. GLE72 is of special interest because it is one of the only two GLEs of cycle 24, one of the two behind-the-limb GLEs and one of the two smallest GLEs of cycles 23 and 24.

Determination of the coronal electron density by the inversion of white-light polarized brightness (pB) measurements by coronagraphs is a classic problem in solar physics. An inversion technique based on the spherically symmetric geometry (Spherically Symmetric Inversion, SSI) was developed in the 1950s, and has been widely applied to interpret various observations. However, to date there is no study about uncertainty estimation of this method. In this study we present the detailed assessment of this method using a three-dimensional (3D) electron density in the corona from 1.5 to 4 Rsun as a model, which is reconstructed by tomography method from STEREO/COR1 observations during solar minimum in February 2008. We first show in theory and observation that the spherically symmetric polynomial approximation (SSPA) method and the Van de Hulst inversion technique are equivalent. Then we assess the SSPA method using synthesized pB images from the 3D density model, and find that the SSPA density values are close to the model inputs for the streamer core near the plane of the sky (POS) with differences generally less than a factor of two or so; the former has the lower peak but more spread in both longitudinal and latitudinal directions than the latter. We estimate that the SSPA method may resolve the coronal density structure near the POS with angular resolution in longitude of about 50 degrees. Our results confirm the suggestion that the SSI method is applicable to the solar minimum streamer (belt) as stated in some previous studies. In addition, we demonstrate that the SSPA method can be used to reconstruct the 3D coronal density, roughly in agreement with that by tomography for a period of low solar activity. We suggest that the SSI method is complementary to the 3D tomographic technique in some cases, given that the development of the latter is still an ongoing research effort.

Measurement of the coronal magnetic field is a crucial ingredient in understanding the nature of solar coronal phenomena at all scales. We employed STEREO/COR1 data obtained during a deep minimum of solar activity in February 2008 (Carrington rotation CR 2066) to retrieve and analyze the three-dimensional (3D) coronal electron density in the range of heights from 1.5 to 4 Rsun using a tomography method. With this, we qualitatively deduced structures of the coronal magnetic field. The 3D electron density analysis is complemented by the 3D STEREO/EUVI emissivity in the 195 A band obtained by tomography for the same CR. A global 3D MHD model of the solar corona was used to relate the reconstructed 3D density and emissivity to open/closed magnetic field structures. We show that the density maximum locations can serve as an indicator of current sheet position, while the locations of the density gradient maximum can be a reliable indicator of coronal hole boundaries. We find that the magnetic field configuration during CR 2066 has a tendency to become radially open at heliocentric distances greater than 2.5 Rsun. We also find that the potential field model with a fixed source surface (PFSS) is inconsistent with the boundaries between the regions with open and closed magnetic field structures. This indicates that the assumption of the potential nature of the coronal global magnetic field is not satisfied even during the deep solar minimum. Results of our 3D density reconstruction will help to constrain solar coronal field models and test the accuracy of the magnetic field approximations for coronal modeling.

Using data from STEREO and SOHO spacecraft, we show that temporal organization of energy release events in the quiet solar corona is close to random, in contrast to the clustered behavior of flaring times in solar active regions. The locations of the quiet-Sun events follow the meso- and supergranulation pattern of the underling photosphere. Together with earlier reports of the scale-free event size statistics, our findings suggest that quiet solar regions responsible for bulk coronal heating operate in a driven self-organized critical state, possibly involving long-range Alfv\'{e}nic interactions.

Major solar eruptive events (SEEs), consisting of both a large flare and a near simultaneous large fast coronal mass ejection (CME), are the most powerful explosions and also the most powerful and energetic particle accelerators in the solar system, producing solar energetic particles (SEPs) up to tens of GeV for ions and hundreds of MeV for electrons. The intense fluxes of escaping SEPs are a major hazard for humans in space and for spacecraft. Furthermore, the solar plasma ejected at high speed in the fast CME completely restructures the interplanetary medium (IPM) - major SEEs therefore produce the most extreme space weather in geospace, the interplanetary medium, and at other planets. Thus, understanding the flare/CME energy release process(es) and the related particle acceleration processes are major goals in Heliophysics. To make the next major breakthroughs, we propose a new mission concept, SEE 2020, a single spacecraft with a complement of advanced new instruments that focus directly on the coronal energy release and particle acceleration sites, and provide the detailed diagnostics of the magnetic fields, plasmas, mass motions, and energetic particles required to understand the fundamental physical processes involved.

A set of co-aligned high resolution images from the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory (SDO) is used to investigate propagating disturbances (PDs) in warm fan loops at the periphery of a non-flaring active region NOAA AR 11082. To measure PD speeds at multiple coronal temperatures, a new data analysis methodology is proposed enabling quantitative description of subvisual coronal motions with low signal-to-noise ratios of the order of 0.1 %. The technique operates with a set of one-dimensional "surfing" signals extracted from position-time plots of several AIA channels through a modified version of Radon transform. The signals are used to evaluate a two-dimensional power spectral density distribution in the frequency - velocity space which exhibits a resonance in the presence of quasi-periodic PDs. By applying this analysis to the same fan loop structures observed in several AIA channels, we found that the traveling velocity of PDs increases with the temperature of the coronal plasma following the square root dependence predicted for the slow mode magneto-acoustic wave which seems to be the dominating wave mode in the studied loop structures. This result extends recent observations by Kiddie et al. (Solar Phys., 2012) to a more general class of fan loop systems not associated with sunspots and demonstrating consistent slow mode activity in up to four AIA channels.

Quasi-periodic propagating intensity disturbances (PDs) have been observed in large coronal loops in EUV images over a decade, and are widely accepted to be slow magnetosonic waves. However, spectroscopic observations from Hinode/EIS revealed their association with persistent coronal upflows, making this interpretation debatable. Motivated by the scenario that the coronal upflows could be cumulative result of numerous individual flow pulses generated by sporadic heating events (nanoflares) at the loop base, we construct a velocity driver with repetitive tiny pulses, whose energy frequency distribution follows the flare power-law scaling. We then perform 3D MHD modeling of an idealized bipolar active region by applying this broadband velocity driver at the footpoints of large coronal loops which appear open in the computational domain. Our model successfully reproduces the PDs with similar features as the observed, and shows that any upflow pulses inevitably excite slow magnetosonic wave disturbances propagating along the loop. We find that the generated PDs are dominated by the wave signature as their propagation speeds are consistent with the wave speed in the presence of flows, and the injected flows rapidly decelerate with height. Our simulation results suggest that the observed PDs and associated persistent upflows may be produced by small-scale impulsive heating events (nanoflares) at the loop base, and that the flows and waves may both contribute to the PDs at lower heights.

The observed solar activity is believed to be driven by the dissipation of nonpotential magnetic energy injected into the corona by dynamic processes in the photosphere. The enormous range of scales involved in the interaction makes it difficult to track down the photospheric origin of each coronal dissipation event, especially in the presence of complex magnetic topologies. In this paper, we propose an ensemble-based approach for testing the photosphere - corona coupling in a quiet solar region as represented by intermittent activity in SOHO MDI and STEREO EUVI image sets. For properly adjusted detection thresholds corresponding to the same degree of intermittency in the photosphere and corona, the dynamics of the two solar regions is described by the same occurrence probability distributions of energy release events but significantly different geometric properties. We derive a set of scaling relations reconciling the two groups of results and enabling statistical description of coronal dynamics based on photospheric observations. Our analysis suggests that multiscale intermittent dissipation in the corona at spatial scales > 3 Mm is controlled by turbulent photospheric convection. Complex topology of the photospheric network makes this coupling essentially nonlocal and non-deterministic. Our results are in an agreement with the Parker's coupling scenario in which random photospheric shuffling generates marginally stable magnetic discontinuities at the coronal level, but they are also consistent with an impulsive wave heating involving multiscale Alfvenic wave packets and/or MHD turbulent cascade. A back reaction on the photosphere due to coronal magnetic reconfiguration can be a contributing factor.

We report on the 2012 May 17 Ground Level Enhancement (GLE) event, which is the first of its kind in Solar Cycle 24. This is the first GLE event to be fully observed close to the surface by the Solar Terrestrial Relations Observatory (STEREO) mission. We determine the coronal mass ejection (CME) height at the start of the associated metric type II radio burst (i.e., shock formation height) as 1.38 Rs (from the Sun center). The CME height at the time of GLE particle release was directly measured from a STEREO image as 2.32 Rs, which agrees well with the estimation from CME kinematics. These heights are consistent with those obtained for cycle-23 GLEs using back-extrapolation. By contrasting the 2012 May 17 GLE with six other non-GLE eruptions from well-connected regions with similar or larger flare size and CME speed, we find that the latitudinal distance from the ecliptic is rather large for the non-GLE events due to a combination of non-radial CME motion and unfavorable solar B0 angle, making the connectivity to Earth poorer. We also find that the coronal environment may play a role in deciding the shock strength.

Recent EUV spectroscopic observations indicate that slow magnetosonic waves are present in active region (AR) loops. Some of the spectral data were also interpreted as evidence of fast (~100-300 km/s) quasi-periodic flows. We have performed three-dimensional magnetohydrodynamic (3D MHD) modeling of a bipolar AR that contains impulsively generated waves and flows in coronal loops. The model AR is initiated with a dipole magnetic field and gravitationally stratified density, with an upflow driven steadily or periodically in localized regions at the footpoints of magnetic loops. The resulting flows along the magnetic field lines of the AR produce higher density loops compared to the surrounding plasma by injection of material into the flux-tubes and the establishment of siphon flow. We find that the impulsive onset of flows with subsonic speeds result in the excitation of damped slow magnetosonic waves that propagate along the loops and coupled nonlinearly driven fast mode waves. The phase speed of the slow magnetosonic waves is close to the coronal sound speed. When the amplitude of the driving pulses is increased we find that slow shock-like wave trains are produced. When the upflows are driven periodically, undamped oscillations are produced with periods determined by the periodicity of the upflows. Based on the results of the 3D MHD model we suggest that the observed slow magnetosonic waves and persistent upflows may be produced by the same impulsive events at the bases of ARs.

It is difficult to measure the true speed of Earth-directed CMEs from a coronagraph located along the Sun-Earth line because of the occulting disk. However, the expansion speed (the speed with which the CME appears to spread in the sky plane) can be measured by such a coronagraph. In order to convert the expansion speed to radial speed (which is important for space weather applications) one can use an empirical relationship between the two that assumes an average width for all CMEs. If we have the width information from quadrature observations, we can confirm the relationship between expansion and radial speeds derived by Gopalswamy et al. (2009a). The STEREO spacecraft were in qudrature with SOHO (STEREO-A ahead of Earth by 87o and STEREO-B 94o behind Earth) on 2011 February 15, when a fast Earth-directed CME occurred. The CME was observed as a halo by the Large-Angle and Spectrometric Coronagraph (LASCO) on board SOHO. The sky-plane speed was measured by SOHO/LASCO as the expansion speed, while the radial speed was measured by STEREO-A and STEREO-B. In addition, STEREO-A and STEREO-B images provided the width of the CME, which is unknown from Earth view. From the SOHO and STEREO measurements, we confirm the relationship between the expansion speed (Vexp) and radial speed (Vrad) derived previously from geometrical considerations (Gopalswamy et al. 2009a): Vrad = 1/2 (1 + cot w)Vexp, where w is the half width of the CME. STEREO-B images of the CME, we found that CME had a full width of 76o, so w = 38o. This gives the relation as Vrad = 1.14 Vexp. From LASCO observations, we measured Vexp = 897 km/s, so we get the radial speed as 1023 km/s. Direct measurement of radial speed yields 945 km/s (STEREO-A) and 1058 km/s (STEREO-B). These numbers are different only by 7.6% and 3.4% (for STEREO-A and STEREO-B, respectively) from the computed value.

The first evidence of transverse oscillations of a multistranded loop with growing amplitudes and internal coupling observed by the Atomspheric Imaging Assembly (AIA) onboard the Solar Dynamics Observatory (SDO) is presented. The loop oscillation event occurred on 2011 March 8, triggered by a CME. The multiwavelength analysis reveals the presence of multithermal strands in the oscillating loop, whose dynamic behaviors are temperature-dependent, showing differences in their oscillation amplitudes, phases and emission evolution. The physical parameters of growing oscillations of two strands in 171 A are measured and the 3-D loop geometry is determined using STEREO-A/EUVI data. These strands have very similar frequencies, and between two 193 A strands a quarter-period phase delay sets up. These features suggest the coupling between kink oscillations of neighboring strands and the interpretation by the collective kink mode as predicted by some models. However, the temperature dependence of the multistarnded loop oscillations was not studied previously and needs further investigation. The transverse loop oscillations are associated with intensity and loop width variations. We suggest that the amplitude-growing kink oscillations may be a result of continuous non-periodic driving by magnetic deformation of the CME, which deposits energy into the loop system at a rate faster than its loss.

Quasi-periodic intensity disturbances propagating upward along the coronal structure have been extensively studied using EUV imaging observations from SOHO/EIT and TRACE. They were interpreted as either slow mode magnetoacoustic waves or intermittent upflows. In this study we aim at demonstrating that time series of spectroscopic observations are critical to solve this puzzle. Propagating intensity and Doppler shift disturbances in fanlike coronal loops are analyzed in multiple wavelengths using the sit-and-stare observations from Hinode/EIS. We find that the disturbances did not cause the blue-wing asymmetry of spectral profiles in the warm (~1.5 MK) coronal lines. The estimated small line-of-sight velocities also did not support the intermittent upflow interpretation. In the hot (~2 MK) coronal lines the disturbances did cause the blue-wing asymmetry, but the double fits revealed that a high-velocity minor component is steady and persistent, while the propagating intensity and Doppler shift disturbances are mainly due to variations of the core component, therefore, supporting the slow wave interpretation. However, the cause for blueward line asymmetries remains unclear.

Multiscale topological complexity of solar magnetic field is among the primary factors controlling energy release in the corona, including associated processes in the photospheric and chromospheric boundaries. We present a new approach for analyzing multiscale behavior of the photospheric magnetic flux underlying this dynamics as depicted by a sequence of high-resolution solar magnetograms. The approach involves two basic processing steps: (1) identification of timing and location of magnetic flux origin and demise events (as defined by DeForest et al., 2007) by tracking spatiotemporal evolution of unipolar and bipolar photospheric regions, and (2) analysis of collective behavior of the detected magnetic events using a generalized version of Grassberger - Procaccia correlation integral algorithm. The scale-free nature of the developed algorithms makes it possible to characterize the dynamics of the photospheric network across a wide range of distances and relaxation times. Three types of photospheric conditions are considered to test the method: a quiet photosphere, a solar active region (NOAA 10365) in a quiescent non-flaring state, and the same active region during a period of M-class flares. The results obtained show (1) the presence of a topologically complex asymmetrically fragmented magnetic network in the quiet photosphere driven by meso- and supergranulation, (2) the formation of non-potential magnetic structures with complex polarity separation lines inside the active region, and (3) statistical signatures of canceling bipolar magnetic structures coinciding with flaring activity in the active region. Each of these effects can represent an unstable magnetic configuration acting as an energy source for coronal dissipation and heating.

Flights of Goddard Space Flight Center's Extreme-Ultraviolet Normal-Incidence Spectrograph (EUNIS) sounding rocket in 2006 and 2007 provided updated radiometric calibrations for SOHO/CDS and Hinode/EIS. EUNIS carried two independent imaging spectrographs covering wavebands of 300-370 A in first order and 170-205 A in second order. After each flight, end-to-end radiometric calibrations of the rocket payload were carried out in the same facility used for pre-launch calibrations of CDS and EIS. During the 2007 flight, EUNIS, SOHO CDS and Hinode EIS observed the same solar locations, allowing the EUNIS calibrations to be directly applied to both CDS and EIS. The measured CDS NIS 1 line intensities calibrated with the standard (version 4) responsivities with the standard long-term corrections are found to be too low by a factor of 1.5 due to the decrease in responsivity. The EIS calibration update is performed in two ways. One is using the direct calibration transfer of the calibrated EUNIS-07 short wavelength (SW) channel. The other is using the insensitive line pairs, in which one member was observed by EUNIS-07 long wavelength (LW) channel and the other by EIS in either LW or SW waveband. Measurements from both methods are in good agreement, and confirm (within the measurement uncertainties) the EIS responsivity measured directly before the instrument's launch. The measurements also suggest that the EIS responsivity decreased by a factor of about 1.2 after the first year of operation. The shape of the EIS SW response curve obtained by EUNIS-07 is consistent with the one measured in laboratory prior to launch. The absolute value of the quiet-Sun He II 304 A intensity measured by EUNIS-07 is consistent with the radiance measured by CDS NIS in quiet regions near the disk center and the solar minimum irradiance obtained by CDS NIS and SDO/EVE recently.

Understanding the solar outer atmosphere requires concerted, simultaneous solar observations from the visible to the vacuum ultraviolet (VUV) and soft X-rays, at high spatial resolution (between 0.1" and 0.3"), at high temporal resolution (on the order of 10 s, i.e., the time scale of chromospheric dynamics), with a wide temperature coverage (0.01 MK to 20 MK, from the chromosphere to the flaring corona), and the capability of measuring magnetic fields through spectropolarimetry at visible and near-infrared wavelengths. Simultaneous spectroscopic measurements sampling the entire temperature range are particularly important. These requirements are fulfilled by the Japanese Solar-C mission (Plan B), composed of a spacecraft in a geosynchronous orbit with a payload providing a significant improvement of imaging and spectropolarimetric capabilities in the UV, visible, and near-infrared with respect to what is available today and foreseen in the near future. The Large European Module for solar Ultraviolet Research (LEMUR), described in this paper, is a large VUV telescope feeding a scientific payload of high-resolution imaging spectrographs and cameras. LEMUR consists of two major components: a VUV solar telescope with a 30 cm diameter mirror and a focal length of 3.6 m, and a focal-plane package composed of VUV spectrometers covering six carefully chosen wavelength ranges between 17 and 127 nm. The LEMUR slit covers 280" on the Sun with 0.14" per pixel sampling. In addition, LEMUR is capable of measuring mass flows velocities (line shifts) down to 2 km/s or better. LEMUR has been proposed to ESA as the European contribution to the Solar C mission.

Coronal mass ejections (CMEs) and corotating interaction regions (CIRs) as well as their source regions are important because of their space weather consequences. The current understanding of CMEs primarily comes from the Solar and Heliospheric Observatory (SOHO) and the Solar Terrestrial Relations Observatory (STEREO) missions, but these missions lacked some key measurements: STEREO did not have a magnetograph; SOHO did not have in-situ magnetometer. SOHO and other imagers such as the Solar Mass Ejection Imager (SMEI) located on the Sun-Earth line are also not well-suited to measure Earth-directed CMEs. The Earth-Affecting Solar Causes Observatory (EASCO) is a proposed mission to be located at the Sun-Earth L5 that overcomes these deficiencies. The mission concept was recently studied at the Mission Design Laboratory (MDL), NASA Goddard Space Flight Center, to see how the mission can be implemented. The study found that the scientific payload (seven remote-sensing and three in-situ instruments) can be readily accommodated and can be launched using an intermediate size vehicle; a hybrid propulsion system consisting of a Xenon ion thruster and hydrazine has been found to be adequate to place the payload at L5. Following a 2-year transfer time, a 4-year operation is considered around the next solar maximum in 2025.

The magnetic field plays a pivotal role in many fields of Astrophysics. This is especially true for the physics of the solar atmosphere. Measuring the magnetic field in the upper solar atmosphere is crucial to understand the nature of the underlying physical processes that drive the violent dynamics of the solar corona -- that can also affect life on Earth. SolmeX, a fully equipped solar space observatory for remote-sensing observations, will provide the first comprehensive measurements of the strength and direction of the magnetic field in the upper solar atmosphere. The mission consists of two spacecraft, one carrying the instruments, and another one in formation flight at a distance of about 200m carrying the occulter to provide an artificial total solar eclipse. This will ensure high-quality coronagraphic observations above the solar limb. Solmex integrates two spectro-polarimetric coronagraphs for off-limb observations, one in the EUV and one in the IR, and three instruments for observations on the disk. The latter comprises one imaging polarimeter in the EUV for coronal studies, a spectro-polarimeter in the EUV to investigate the low corona, and an imaging spectro-polarimeter in the UV for chromospheric studies. SOHO and other existing missions have investigated the emission of the upper atmosphere in detail (not considering polarization), and as this will be the case also for missions planned for the near future. Therefore it is timely that SolmeX provides the final piece of the observational quest by measuring the magnetic field in the upper atmosphere through polarimetric observations.

Theoretical emission-line ratios involving Fe XI transitions in the 257-407 A wavelength range are derived using fully relativistic calculations of radiative rates and electron impact excitation cross sections. These are subsequently compared with both long wavelength channel Extreme-Ultraviolet Imaging Spectrometer (EIS) spectra from the Hinode satellite (covering 245-291 A), and first-order observations (235-449 A) obtained by the Solar Extreme-ultraviolet Research Telescope and Spectrograph (SERTS). The 266.39, 266.60 and 276.36 A lines of Fe XI are detected in two EIS spectra, confirming earlier identifications of these features, and 276.36 A is found to provide an electron density diagnostic when ratioed against the 257.55 A transition. Agreement between theory and observation is found to be generally good for the SERTS data sets, with discrepancies normally being due to known line blends, while the 257.55 A feature is detected for the first time in SERTS spectra. The most useful Fe XI electron density diagnostic is found to be the 308.54/352.67 intensity ratio, which varies by a factor of 8.4 between N_e = 10^8 and 10^11 cm^-3, while showing little temperature sensitivity. However, the 349.04/352.67 ratio potentially provides a superior diagnostic, as it involves lines which are closer in wavelength, and varies by a factor of 14.7 between N_e = 10^8 and 10^11 cm^-3. Unfortunately, the 349.04 A line is relatively weak, and also blended with the second-order Fe X 174.52 A feature, unless the first-order instrument response is enhanced.

The Extreme-Ultraviolet Normal-Incidence Spectrograph sounding-rocket payload was flown on 2006 April 12 (EUNIS-06), carrying two independent imaging spectrographs covering wave bands of 300-370 A in first order and 170-205 A in second order, respectively. The absolute radiometric response of the EUNIS-06 long-wavelength (LW) channel was directly measured in the same facility used to calibrate CDS prior to the SOHO launch. Because the absolute calibration of the short-wavelength (SW) channel could not be obtained from the same lab configuration, we here present a technique to derive it using a combination of solar LW spectra and density- and temperature-insensitive line intensity ratios. The first step in this procedure is to use the coordinated, cospatial EUNIS and SOHO/CDS spectra to carry out an intensity calibration update for the CDS NIS-1 waveband, which shows that its efficiency has decreased by a factor about 1.7 compared to that of the previously implemented calibration. Then, theoretical insensitive line ratios obtained from CHIANTI allow us to determine absolute intensities of emission lines within the EUNIS SW bandpass from those of cospatial CDS/NIS-1 spectra after the EUNIS LW calibration correction. A total of 12 ratios derived from intensities of 5 CDS and 12 SW emission lines from Fe Fe X - Fe XIII yield an instrumental response curve for the EUNIS-06 SW channel that matches well to a relative calibration which relied on combining measurements of individual optical components. Taking into account all potential sources of error, we estimate that the EUNIS-06 SW absolute calibration is accurate to about 20%.

We report the first observation of multiple-periodic propagating disturbances along a fan-like coronal structure simultaneously detected in both intensity and Doppler shift in the Fe XII 195 A line with the EUV Imaging Spectrometer (EIS) onboard Hinode. A new application of coronal seismology is provided based on this observation. We analyzed the EIS sit-and-stare mode observation of oscillations using the running difference and wavelet techniques. Two harmonics with periods of 12 and 25 min are detected. We measured the Doppler shift amplitude of 1-2 km/s, the relative intensity amplitude of 3%-5% and the apparent propagation speed of 100-120 km/s. The amplitude relationship between intensity and Doppler shift oscillations provides convincing evidence that these propagating features are a manifestation of slow magnetoacoustic waves. Detection lengths (over which the waves are visible) of the 25 min wave are about 70-90 Mm, much longer than those of the 5 min wave previously detected by TRACE. This difference may be explained by the dependence of damping length on the wave period for thermal conduction. Based on a linear wave theory, we derive an inclination of the magnetic field to the line-of-sight about 59$\pm$8 deg, a true propagation speed of 128$\pm$25 km/s and a temperature of 0.7$\pm$0.3 MK near the loop's footpoint from our measurements.

We present the first Hinode/EIS observations of 5 min quasi-periodic oscillations detected in a transition-region line (He II) and five coronal lines (Fe X, Fe XII, Fe XIII, Fe XIV, and Fe XV) at the footpoint of a coronal loop. The oscillations exist throughout the whole observation, characterized by a series of wave packets with nearly constant period, typically persisting for 4-6 cycles with a lifetime of 20-30 min. There is an approximate in-phase relation between Doppler shift and intensity oscillations. This provides evidence for slow magnetoacoustic waves propagating upwards from the transition region into the corona. We find that the oscillations detected in the five coronal lines are highly correlated, and the amplitude decreases with increasing temperature. The amplitude of Doppler shift oscillations decrease by a factor of about 3, while that of relative intensity decreases by a factor of about 4 from Fe X to Fe XV. These oscillations may be caused by the leakage of the photospheric p-modes through the chromosphere and transition region into the corona, which has been suggested as the source for intensity oscillations previously observed by TRACE. The temperature dependence of the oscillation amplitudes can be explained by damping of the waves traveling along the loop with multithread structure near the footpoint. Thus, this property may have potential value for coronal seismology in diagnostic of temperature structure in a coronal loop.

Fully relativistic calculations of radiative rates and electron impact excitation cross sections for Fe X are used to derive theoretical emission-line ratios involving transitions in the 174-366 A wavelength range. A comparison of these with solar active region observations obtained during the 1989 and 1995 flights of the Solar Extreme-ultraviolet Research Telescope and Spectrograph (SERTS) reveals generally very good agreement between theory and experiment. Several Fe X emission features are detected for the first time in SERTS spectra, while the transition at 195.32 A is identified for the first time (to our knowledge) in an astronomical source. The most useful Fe X electron density diagnostic line ratios are assessed to be 175.27/174.53 and 175.27/177.24, which both involve lines close in wavelength and free from blends, vary by factors of 13 between Ne = 1E8 and 1E13 cm-3, and yet show little temperature sensitivity. Should these lines not be available, then the 257.25/345.74 ratio may be employed to determine Ne, although this requires an accurate evaluation of the instrument intensity calibration over a relatively large wavelength range. However, if the weak 324.73 A line of Fe X is reliably detected, the use of 324.73/345.74 or 257.25/324.73 is recommended over 257.25/345.74.

An extended data set of extreme ultraviolet images of the solar corona provided by the SOHO spacecraft are analyzed using statistical methods common to studies of self-organized criticality (SOC) and intermittent turbulence (IT). The data exhibits simultaneous hallmarks of both regimes, namely power law avalanche statistics as well as multiscaling of structure functions for spatial activity. This implies that both SOC and IT may be manifestations of a single complex dynamical process entangling avalanches of magnetic energy dissipation with turbulent particle flows.

Recent fully relativistic calculations of radiative rates and electron impact excitation cross sections for Fe {\sc xiii} are used to generate emission-line ratios involving 3s$^{2}$3p$^{2}$--3s3p$^{3}$ and 3s$^{2}$3p$^{2}$--3s$^{2}$3p3d transitions in the 170--225 \AA and 235--450 \AA wavelength ranges covered by the Solar Extreme-Ultraviolet Research Telescope and Spectrograph (SERTS). A comparison of these line ratios with SERTS active region observations from rocket flights in 1989 and 1995 reveals generally very good agreement between theory and experiment. Several new Fe {\sc xiii} emission features are identified, at wavelengths of 203.79, 259.94, 288.56 and 290.81 \AA. However, major discrepancies between theory and observation remain for several Fe {\sc xiii} transitions, as previously found by Landi (2002) and others, which cannot be explained by blending. Errors in the adopted atomic data appear to be the most likely explanation, in particular for transitions which have 3s$^{2}$3p3d $^{1}$D$_{2}$ as their upper level. The most useful Fe {\sc xiii} electron density diagnostics in the SERTS spectral regions are assessed, in terms of the line pairs involved being (i) apparently free of atomic physics problems and blends, (ii) close in wavelength to reduce the effects of possible errors in the instrumental intensity calibration, and (iii) very sensitive to changes in N$_{e}$ over the range 10$^{8}$--10$^{11}$ cm$^{-3}$. It is concluded that the ratios which best satisfy these conditions are 200.03/202.04 and 203.17/202.04 for the 170--225 \AA wavelength region, and 348.18/320.80, 348.18/368.16, 359.64/348.18 and 359.83/368.16 for 235--450 \AA.

New calculations of radiative rates and electron impact excitation cross sections for Fe XI are used to derive emission line intensity ratios involving 3s^23p^4 - 3s^23p^33d transitions in the 180-223 A wavelength range. These ratios are subsequently compared with observations of a solar active region, obtained during the 1995 flight Solar EUV Research Telescope and Spectrograph (SERTS). The version of SERTS flown in 1995 incorporated a multilayer grating that enhanced the instrumental sensitivity for features in the 170 - 225 A wavelength range, observed in second-order between 340 and 450 A. This enhancement led to the detection of many emission lines not seen on previous SERTS flights, which were measured with the highest spectral resolution (0.03 A) ever achieved for spatially resolved active region spectra in this wavelength range. However, even at this high spectral resolution, several of the Fe XI lines are found to be blended, although the sources of the blends are identified in the majority of cases. The most useful Fe XI electron density diagnostic line intensity ratio is I(184.80 A)/I(188.21 A). This ratio involves lines close in wavelength and free from blends, and which varies by a factor of 11.7 between N_e = 10^9 and 10^11 cm^-3, yet shows little temperature sensitivity. An unknown line in the SERTS spectrum at 189.00 A is found to be due to Fe XI, the first time (to our knowledge) this feature has been identified in the solar spectrum. Similarly, there are new identifications of the Fe XI 192.88, 198.56 and 202.42 A features, although the latter two are blended with S VIII/Fe XII and Fe XIII, respectively.