In this paper, we propose a beamforming method for the calibration of the direction-independent gain of the analog chains of aperture arrays. The gain estimates are obtained by cross-correlating the output voltage of each antenna with a voltage beamformed using the other antennas of the array. When the beamforming weights are equal to the average cross-correlated power, a relation is drawn with the StEFCal algorithm. An example illustrates this approach for few point sources and a 256-element array.

This report was submitted as part of the SKA Low Frequency Aperture Array Critical Design Review describing the design of the SKA1-LOW station that took place between 2013 and 2018. The SKA1 LOW field station is inscribed in a circular area having an effective station diameter (centre to centre) of 38 meters and has 256 SKALA4 elements. This document describes the electromagnetic design of the field station. In particular it describes the layout design and the electromagnetic modelling and characteristics of the station. This document describes the effects associated with the layout and array such as mutual coupling effects, side lobe pattern and beam shape (eg. smoothness, calibration models) and presents the state of the art of our ability to measure the array performance and validate the simulation work. The current LFAA field node requirements, derived from the SKA L1 requirements, have evolved over the last years since the LFAA PDR and the System Baseline Design. The SKA1 LOW field station has been designed to meet those requirements and has therefore tracked their evolution (eg. sensitivity requirements, array diameter, etc.). The aforementioned requirements represent a very tight space with a desire for very high sensitivity over a large frequency range (7 to 1) and wide field of view (90 degrees cone around zenith) while keeping the station diameter to a minimum, so as the filling factor but at the same time allowing for sufficient space between antennas to allow for easy maintenances, amongst many others. This results in a complex design.

LaRa (Lander Radioscience) is an experiment on the ExoMars 2020 mission that uses the Doppler shift on the radio link due to the motion of the ExoMars platform tied to the surface of Mars with respect to the Earth ground stations (e.g. the deep space network stations of NASA), in order to precisely measure the relative velocity of the lander on Mars with respect to the Earth. The LaRa measurements shall improve the understanding of the structure and processes in the deep interior of Mars by obtaining the rotation and orientation of Mars with a better precision compared to the previous missions. In this paper, we provide the analysis done until now for the best realization of these objectives. We explain the geophysical observation that will be reached with LaRa (Length-of-day variations, precession, nutation, and possibly polar motion). We develop the experiment set up, which includes the ground stations on Earth (so-called ground segment). We describe the instrument, i.e. the transponder and its three antennas. We further detail the link budget and the expected noise level that will be reached. Finally, we detail the expected results, which encompasses the explanation of how we shall determine Mars' orientation parameters, and the way we shall deduce Mars' interior structure and Mars' atmosphere from them. Lastly, we explain briefly how we will be able to determine the Surface platform position.

Large radio telescopes in the 21st century such as the Low-Frequency Array (LOFAR) or the Murchison Widefield Array (MWA) make use of phased aperture arrays of antennas to achieve superb survey speeds. The Square Kilometer Array low frequency instrument (SKA1-LOW) will consist of a collection of non-regular phased array systems. The prediction of the main beam of these arrays using a few coefficients is crucial for the calibration of the telescope. An effective approach to model the main beam and first few sidelobes for large non-regular arrays is presented. The approach exploits Zernike polynomials to represent the array pattern. Starting from the current defined on an equivalence plane located just above the array, the pattern is expressed as a sum of Fourier transforms of Zernike functions of different orders. The coefficients for Zernike polynomials are derived by two different means: least-squares and analytical approaches. The analysis shows that both approaches provide a similar performance for representing the main beam and first few sidelobes. Moreover, numerical results for different array configurations are provided, which demonstrate the performance of the proposed method, also for arrays with shapes far from circular.

A fast full-wave simulation technique is presented for the analysis of large irregular planar arrays of identical 3-D metallic antennas. The solution method relies on the Macro Basis Functions (MBF) approach and an interpolatory technique to compute the interactions between MBFs. The Harmonic-polynomial (HARP) model is established for the near-field interactions in a modified system of coordinates. For extremely large arrays made of complex antennas, two approaches assuming a limited radius of influence for mutual coupling are considered: one is based on a sparse-matrix LU decomposition and the other one on a tessellation of the array in the form of overlapping sub-arrays. The computation of all embedded element patterns is sped up with the help of the non-uniform FFT algorithm. Extensive validations are shown for arrays of log-periodic antennas envisaged for the low-frequency SKA (Square Kilometer Array) radio-telescope. The analysis of SKA stations with such a large number of elements has not been treated yet in the literature. Validations include comparison with results obtained with commercial software and with experiments. The proposed method is particularly well suited to array synthesis, in which several orders of magnitude can be saved in terms of computation time.