Light pollution is one of the most rapidly increasing types of environmental degradation. To limit this pollution several effective practices have been defined: shields on lighting fixtures to prevent direct upward light; no over lighting, i.e. avoid using higher lighting levels than strictly needed for the task, constraining illumination to the area where and when it is needed. Nevertheless, even after the best control of the light distribution is reached and when the proper quantity of light is used, upward light emission remains, due to reflections from the lit surfaces and atmospheric scatter. The environmental impact of this "residual light pollution" cannot be neglected and should be limited too. We propose a new way to limit the effects of this residual light pollution on wildlife, human health and stellar visibility. We performed analysis of the spectra of common types of lamps for external use, including the new LEDs. We evaluated their emissions relative to the spectral response functions of human eye photoreceptors, in the photopic, scotopic and melatonin suppressing bands finding that the amount of pollution is strongly dependent on the spectral characteristics of the lamps, with the more environmentally friendly lamps being low pressure sodium, followed by high pressure sodium. Most polluting are the lamps with a strong blue emission, like white LEDs. Migration from the now widely used sodium lamps to white lamps (Metal Halide and LEDs) would produce an increase of pollution in the scotopic and melatonin suppression bands of more than five times the present levels, supposing the same photopic installed flux. This increase will exacerbate known and possible unknown effects of light pollution on human health, environment and on starry sky visibility. We present quantitative criteria to evaluate the lamps based on their spectral emissions and we suggest regulatory limits.

Light pollution is a worldwide problem that has a range of adverse effects on human health and natural ecosystems. Using data from the New World Atlas of Artificial Night Sky Brightness, VIIRS-recorded radiance and Gross Domestic Product (GDP) data, we compared light pollution levels, and the light flux to the population size and GDP at the State and County levels in the USA and at Regional (NUTS2) and Province (NUTS3) levels in Europe. We found 6800-fold differences between the most and least polluted regions in Europe, 120-fold differences in their light flux per capita, and 267-fold differences in flux per GDP unit. Yet, we found even greater differences between US counties: 200,000-fold differences in sky pollution, 16,000-fold differences in light flux per capita, and 40,000-fold differences in light flux per GDP unit. These findings may inform policy-makers, helping to reduce energy waste and adverse environmental, cultural and health consequences associated with light pollution.

Modelling techniques for the propagation of light pollution in the atmosphere allow the computation of maps of artificial night sky brightness in any direction of the sky, involving a large number of details from satellite data. Cinzano et al. (2001a) introduced a method of mapping naked eye star visibility at the zenith from large areas based on satellite radiance measurements and Garstang models of the propagation of light pollution. It takes into account the altitude of each land area from digital elevation data, natural sky brightness in the chosen sky direction based on the Garstang approach, eye capability after Garstang and Schaefer, and atmospheric extinction in the visual photometric band. Here we discuss how to use these methods to obtain maps of the average number of visible stars when looking at the night sky hemisphere, finally answering, site by site, the question of how many stars are visible in the sky. This is not trivial, as the number of stars visible depends on the limiting magnitude in each direction in the sky, and this depends on sky brightness in that direction, atmospheric extinction at that zenith distance and the observer's visual acuity and experience. We present, as an example, a map of the number of visible stars in Italy to an average observer on clear nights with a resolution of approximately 1 km.

Artificial lights raise night sky luminance, creating the most visible effect of light pollution-artificial skyglow. Despite the increasing interest among scientists in fields such as ecology, astronomy, health care, and land-use planning, light pollution lacks a current quantification of its magnitude on a global scale. To overcome this, we present the world atlas of artificial sky luminance, computed with our light pollution propagation software using new high-resolution satellite data and new precision sky brightness measurements. This atlas shows that more than 80% of the world and more than 99% of the U.S. and European populations live under light-polluted skies. The Milky Way is hidden from more than one-third of humanity, including 60% of Europeans and nearly 80% of North Americans. Moreover, 23% of the world's land surfaces between 75{\deg}N and 60{\deg}S, 88% of Europe, and almost half of the United States experience light-polluted nights.

Methods to map artificial night sky brightness and stellar visibility across large territories or their distribution over the entire sky at any site are based on the computation of the propagation of light pollution with Garstang models, a simplified solution of the radiative transfer problem in the atmosphere which allows a fast computation by reducing it to a ray-tracing approach. We present here up-to-date Extended Garstang Models (EGM) which provide a more general numerical solution for the radiative transfer problem applied to the propagation of light pollution in the atmosphere. We also present the LPTRAN software package, an application of EGM to high-resolution DMSP-OLS satellite measurements of artificial light emissions and to GTOPO30 digital elevation data, which provides an up-to-date method to predict the artificial brightness distribution of the night sky at any site in the World at any visible wavelength for a broad range of atmospheric situations and the artificial radiation density in the atmosphere across the territory. EGM account for (i) multiple scattering, (ii) wavelength from 250 nm to infrared, (iii) Earth curvature and its screening effects, (iv) sites and sources elevation, (v) many kinds of atmosphere with the possibility of custom setup (e.g. including thermal inversion layers), (vi) mix of different boundary layer aerosols and tropospheric aerosols, with the possibility of custom setup, (vii) up to 5 aerosol layers in upper atmosphere including fresh and aged volcanic dust and meteoric dust, (viii) variations of the scattering phase function with elevation, (ix) continuum and line gas absorption from many species, ozone included, (x) up to 5 cloud layers, (xi) wavelength dependant bidirectional reflectance of the ground surface from NASA/MODIS satellites, main models or custom data (snow included), (xii) geographically variable upward light emission function.

We apply the sky brightness modelling technique introduced and developed by Roy Garstang to high-resolution DMSP-OLS satellite measurements of upward artificial light flux and to GTOPO30 digital elevation data in order to predict the brightness distribution of the night sky at a given site in the primary astronomical photometric bands for a range of atmospheric aerosol contents. This method, based on global data and accounting for elevation, Earth curvature and mountain screening, allows the evaluation of sky glow conditions over the entire sky for any site in the World, to evaluate its evolution, to disentangle the contribution of individual sources in the surrounding territory, and to identify main contributing sources. Sky brightness, naked eye stellar visibility and telescope limiting magnitude are produced as 3-dimensional arrays whose axes are the position on the sky and the atmospheric clarity. We compared our results to available measurements.

We present the first World Atlas of the zenith artificial night sky brightness at sea level. Based on radiance calibrated high resolution DMSP satellite data and on accurate modelling of light propagation in the atmosphere, it provides a nearly global picture of how mankind is proceeding to envelope itself in a luminous fog. Comparing the Atlas with the U.S. Department of Energy (DOE) population density database we determined the fraction of population who are living under a sky of given brightness. About two thirds of the World population and 99% of the population in US (excluding Alaska and Hawaii) and EU live in areas where the night sky is above the threshold set for polluted status. Assuming average eye functionality, about one fifth of the World population, more than two thirds of the US population and more than one half of the EU population have already lost naked eye visibility of the Milky Way. Finally, about one tenth of the World population, more than 40% of the US population and one sixth of the EU population no longer view the heavens with the eye adapted to night vision because the sky brightness.

We extend the method introduced by Cinzano et al. (2000a) to map the artificial sky brightness in large territories from DMSP satellite data, in order to map the naked eye star visibility and telescopic limiting magnitudes. For these purposes we take into account the altitude of each land area from GTOPO30 world elevation data, the natural sky brightness in the chosen sky direction, based on Garstang modelling, the eye capability with naked eye or a telescope, based on the Schaefer (1990) and Garstang (2000b) approach, and the stellar extinction in the visual photometric band. For near zenith sky directions we also take into account screening by terrain elevation. Maps of naked eye star visibility and telescopic limiting magnitudes are useful to quantify the capability of the population to perceive our Universe, to evaluate the future evolution, to make cross correlations with statistical parameters and to recognize areas where astronomical observations or popularisation can still acceptably be made. We present, as an application, maps of naked eye star visibility and total sky brightness in V band in Europe at the zenith with a resolution of approximately 1 km.

We present a method to map the artificial sky brightness across large territories in astronomical photometric bands with a resolution of approximately 1 km. This is useful to quantify the situation of night sky pollution, to recognize potential astronomical sites and to allow future monitoring of trends. The artificial sky brightness present in the chosen direction at a given position on the Earth's surface is obtained by the integration of the contributions produced by every surface area in the surrounding. Each contribution is computed based on detailed models for the propagation in the atmosphere of the upward light flux emitted by the area. The light flux is measured with top of atmosphere radiometric observations made by the Defense Meteorological Satellite Program (DMSP) Operational Linescan System. We applied the described method to Europe obtaining the maps of artificial sky brightness in V and B bands.

We present the map of the artificial sky brightness in Europe in V band with a resolution of approximately 1 km. The aim is to understand the state of night sky pollution in Europe, to quantify the present situation and to allow future monitoring of trends. The artificial sky brightness in each site at a given position on the sky is obtained by integration of the contributions produced by every surface area in the surroundings of the site. Each contribution is computed taking into account based on detailed models the propagation in the atmosphere of the upward light flux emitted by the area and measured by the Operational Linescan System of DMSP satellites. The modelling technique, introduced and developed by Garstang and also applied by Cinzano, takes into account the extinction along light paths, a double scattering of light from atmospheric molecules and aerosols, Earth curvature and allows to associate the predictions to the aerosol content of the atmosphere.

We present a project to map the artificial sky brightness in Europe in the main astronomical photometrical bands with a resolution better than 3 km. The aim is to understand the state of night sky pollution in Europe, to quantify the present situation and to allow future monitoring of trends. The artificial sky brightness in each site at a given position on the sky is obtained by the integration of the contributions produced by every surface area in the surroundings of the site. Each contribution is computed taking in account the propagation in the atmosphere of the upward light flux emitted by the area and measured from DMSP satellites. The project is a long term study in which we plan to take in account successively of many different details in order to improve the maps. We present, as a preliminary result, a map of the V-band artificial sky brightness in Italy in 1998 and we compare it with the map obtained 27 years earlier by Bertiau, Treanor and De Graeve. Predictions for the artificial sky brightness within the next 27 years are also shown.

We obtained the map of the zenith brightness of the night sky in Italy. The artificial sky brightness in each site is computed by integration of the contributions by each unitary area of surface obtained by applying a propagation function to the upward emission of the area as obtained from DMSP satellite night-time images. We also evaluated the emission versus population relationship comparing the relative emissions of a number of cities of various populations.

We present the kinematics and photometry of the stars and of the ionized gas near the centre of the S0 galaxy NGC4036. Dynamical models based on the Jeans Equation have been constructed from the stellar data to determine the gravitational potential in which the ionized gas is expected to orbit. Inside 10'', the observed gas rotation curve falls well short of the predicted circular velocity. Over a comparable radial region the observed gas velocity dispersion is far higher than the one expected from thermal motions or small scale turbulence, corroborating that the gas cannot be following the streamlines of nearly closed orbits. We explore several avenues to understand the dynamical state of the gas: (1) We treat the gas as a collisionless ensemble of cloudlets and apply the Jeans Equation to it; this modeling shows that inside 4'' the gas velocity dispersion is just high enough to explain quantitatively the absence of rotation. (2) Alternatively, we explore whether the gas may arise from the `just shed' mass-loss envelopes of the bulge stars, in which case their kinematics should simply mimic that of the stars. he latter approach matches the data better than (1), but still fails to explain the low velocity dispersion and slow rotation velocity of the gas for 5''<r<10''. (3) Finally, we explore, whether drag forces on the ionized gas may aid in explaining its peculiar kinematics. While all these approaches provide a much better description of the data than cold gas on closed orbits, we do not yet have a definitive model to describe the observed gas kinematics at all radii.

The kinematics of stars and ionized gas has been studied near the center of the S0 galaxy NGC 4036. Dynamical models based both on stellar photometry and kinematics have been built in order to derive the gravitational potential in which the gas is expected to orbit. The observed gas rotation curve falls short of the circular velocity curve inferred from these models. Inside 10'' the observed gas velocity dispersion is found to be comparable to the predicted circular velocity, showing that the gas cannot be considered on circular orbits. The understanding of the observed gas kinematics is improved by models based on the Jeans Equations, which assume the ionized gas as an ensemble of collisionless cloudlets distributed in a spheroidal and in a disk component.

The direction of the upward light emission has different polluting effects on the sky depending on the distance of the observation site. We studied with detailed models for light pollution propagation the ratio $(b_{H})/(b_{L})$, at given distances from a city, between the artificial sky luminance $b_{H}$ produced by its upward light emission between a given threshold angle $\theta_{0}$ and the vertical and the artificial sky luminance $b_{L}$ produced by its upward light emission between the horizontal and the threshold angle $\theta_{0}$. Our results show that as the distance from the city increases the effects of the emission at high angles above the horizontal decrease relative to the effects of emission at lower angles above the horizontal. Outside some kilometers from cities or towns the light emitted between the horizontal and 10\deg ~is as important as the light emitted at all the other angles in producing the artificial sky luminance. Therefore the protection of a site requires also a careful control of this emission which needs to be reduced to at most 1/10 of the remaining emission. The emission between the horizontal and 10\deg ~is mostly produced by spill light from luminaires, so fully shielded fixtures (e.g. flat glass luminaires or asymmetric spot-lights installed without any tilt) are needed for this purpose.

The knowledge of the contribution $b_d(d)$ to the artificial sky luminance in a given point of the sky of a site produced by the sources beyond a given distance $d$ from it is important to understand the behaviour of light pollution in diffusely urbanized areas and to estimate which fraction of the artificial luminance would be regulated by norms or laws limiting the light wasted upward within protection areas of given radii. I studied the behaviour of $b_d(d)$ constructing a model for the propagation of the light pollution based on the modelling technique introduced by Garstang which allows to calculate the contribution to the artificial luminance in a given point of the sky of a site of given altitude above sea level, produced by a source of given emission and geographic position. I obtained $b_d(d)$ integrating the contribution to the artificial luminance from every source situated at a distance greater than $d$. I also presented an analitical expression for $b_d(d)$ depending mainly from one parameter, a core radius, well reproducing model's results. In this paper I present the results for $b_d(d)$ at some Italian Astronomical Observatories. In a diffusely urbanised territory the artificial sky luminance produced by sources located at large distances from the site is not negligible due at the additive character of light pollution and its propagation at large distances. Only when the core radius is small, e.g. for sites in the inner outskirts of a city, the sky luminance from sources beyond few kilometers is negligible. The radii of protection zones around Observatories needs to be large in order that prescriptions limiting upward light be really effective.

We present stellar and ionized-gas velocity curves and velocity dispersion profiles for the Sa galaxies NGC 2179 and NGC 2775. Using their luminosity profiles and modeling both their stellar and gaseous kinematics, we have derived the mass distribution of the dark and the luminous matter. This unambiguously shows that, inside one disk length-scale R_D, the stellar bulge and disk account for the whole gravitating mass. The dark matter halo, likely present also at inner radii, becomes an important mass component only for R > 2 R_D. Giving the quantity and quality of the data, our results on these two luminous galaxies serve as strong counter-example to the recent claim according to which also high-luminosity spirals are dark matter dominated at essentially all radii.