IUCAA Digital Sampling Array Controller (IDSAC) is a flexible and generic yet powerful CCD controller which can handle a wide range of scientific detectors. Based on an easily scalable modular backplane architecture consisting of Single Board Controllers (SBC), IDSAC can control large detector arrays and mosaics. Each of the SBCs offers the full functionality required to control a CCD independently. The SBCs can be cold swapped without the need to reconfigure them. Each SBC can handle data from up to four video channels with or without dummy outputs at speeds up to 500 kilo Pixels Per Second (kPPS) Per Channel with a resolution of 16 bits. Communication with Linux based host computer is through a USB3.0 interface, with the option of using copper or optical fibers. A Field Programmable Gate Array (FPGA) is used as the master controller in each SBC which allows great flexibility in optimizing performance by adjusting gain, timing signals, bias levels, etc. using user-editable configuration files without altering the circuit topology. Elimination of thermal kTC noise is achieved via Digital Correlated Double Sampling (DCDS). We present the results of noise performance characterization of IDSAC through simulation, theoretical modeling, and actual measurements. The contribution of different types of noise sources is modeled using a tool to predict noise of a generic DCDS signal chain analytically. The analytical model predicts the net input referenced noise of the signal chain to be 5 electrons for 200k pixels per second per channel readout rate with 3 samples per pixel. Using a cryogenic test set up in the lab, the noise is measured to be 5.4 e (24.3 \muV), for the same readout configuration.

IUCAA Digital Sampling Array Controller (IDSAC) is a generic CCD Controller which is flexible and powerful enough to control a wide variety of CCDs and CMOS detectors used for ground-based astronomy. It has a fully scalable architecture, which can control multiple CCDs and can be easily expanded. The controller has a modular backplane architecture consists of Single Board Controller Cards (SBCs) and can control a mosaic or independent of 5 CCDs. Key features of IDSAC contains usage of FPGA as a reconfigurable master controller, implementation of Digital CDS to achieve low noise and ability to process upto four CCD output at 1Mpixels/Sec/Channel with 16-bit resolution. The best feature of IDSAC is it uses the technique of Digital Correlated Double Sampling(DCDS). It is known that CCD video output is dominated by thermal KTC noise contributed from the summing well capacitor of the CCD output circuitry. To eliminate thermal KTC noise Correlated Double Sampling (CDS) is a very standard technique. CDS performed in Digital domain (DCDS) has several advantages over its analog counterpart, such as - less electronics, faster readout and easier post processing. It is also flexible with sampling rate and pixel throughput while maintaining the core circuit topology intact. The noise characterization of the IDSAC CDS signal chain has been performed by analytical modelling, software simulation and practical measurements. Various types of noise such as white, pink, power supply, bias etc. has been considered while creating a analytical noise model tool to predict noise of a controller system like IDSAC. Standard test bench softwares like Pspice and Multisim are used to simulate the noise performance while several tests are performed to measure the actual noise of IDSAC.The theoretical calculation matches very well with component level simulation as well as practical measurements within 10% accuracy.

Although the astronomy community is witnessing an era of large telescopes, smaller and medium sized telescopes still maintain their utility being larger in numbers. In order to obtain better scientific outputs it is necessary to incorporate modern and advanced technologies to the back-end instruments and to their interfaces with the telescopes through various control processes. However often tight financial constraints on the smaller and medium size observatories limit the scope and utility of these systems. Most of the time for every new development on the telescope the back-end control systems are required to be built from scratch leading to high costs and efforts. Therefore a simple, low cost control system for small and medium size observatory needs to be developed to minimize the cost and efforts while going for the expansion of the observatory. Here we report on the development of a modern, multipurpose instrument control system UNICS (Unified Instrument Control System) to integrate the controls of various instruments and devices mounted on the telescope. UNICS consists of an embedded hardware unit called Common Control Unit (CCU) and Linux based data acquisition and User Interface. The Hardware of the CCU is built around the Atmel make ATmega 128 micro-controller and is designed with a back-plane, Master Slave architecture. The Graphical User Interface (GUI) has been developed based on QT and the back end application software is based on C/C++. UNICS provides feedback mechanisms which give the operator a good visibility and a quick-look display of the status and modes of instruments. UNICS is being used for regular science observations since March 2008 on 2m, f/10 IUCAA Telescope located at Girawali, Pune India.