Low energy ground-based cosmic ray air shower experiments generally have energy threshold in the range of a few tens to a few hundreds of TeV. The shower observables are measured indirectly with an array of detectors. The atmospheric absorption of low energy secondaries limits their detection frequencies at the Earth's surface. However, due to selection effects, a tiny fraction of low energy showers, which are produced in the lower atmosphere can reach the observational level. But, due to less information of shower observables, the reconstruction of these showers are arduous. Hence, it is believed that direct measurements by experiments aboard on satellites and balloon flights are more reliable at low energies. Despite having very small efficiency ($\sim$0.1%) at low energies, the large acceptance ($\sim$5 m$^2$sr) of GRAPES-3 experiment allows observing primary cosmic rays down below to $\sim$1 TeV and opens up the possibility to measure primary energy spectrum spanning from a few TeV to beyond cosmic ray knee (up to 10$^{16}$ eV), covering five orders of magnitude. The GRAPES-3 energy threshold for primary protons through Monte Carlo simulations are calculated, which gives reasonably good agreement with data. Furthermore, the total efficiencies and acceptance are also calculated for protons primaries. The ability of GRAPES-3 experiment to cover such a broader energy range may provide a unique handle to bridge the energy spectrum between direct measurements at low energies and indirect measurements at ultra-high energies.

We present the timing and spectral studies of RX J0209.6-7427 during its rare 2019 outburst using observations with the Soft X-ray Telescope (SXT) and Large Area X-ray Proportional Counter (LAXPC) instruments on the AstroSat satellite. Pulsations having a periodicity of 9.29 s were detected for the first time by the NICER mission in the 0.2-10 keV energy band and, as reported here, by AstroSat over a broad energy band covering 0.3-80 keV. The pulsar exhibits a rapid spin-up during the outburst. Energy resolved folded pulse profiles are generated in several energy bands in 3-80 keV. To the best of our knowledge this is the first report of the timing and spectral characteristics of this Be binary pulsar in hard X-rays. There is suggestion of evolution of the pulse profile with energy. The energy spectrum of the pulsar is determined and from the best fit spectral values, the X-ray luminosity of RX J0209.6-7427 is inferred to be ${1.6}\times 10^{39}$ ergs s$^{-1}$. Our timing and spectral studies suggest that this source has features of an ultraluminous X-ray pulsar in the Magellanic Bridge. Details of the results are presented and discussed in terms of the current ideas.

Near-Earth small-body mission targets 162173 Ryugu, 101955 Bennu, and 25143 Itokawa produce gravity fields around 4 orders of magnitude below that of Earth and their irregular shapes, combined with rotational effects produce varying surface potentials. Still, we observe familiar geologic textures and landforms that are the result of the granular physical processes that take place on their surfaces. The nature of these landforms, however, their origins, and how these surfaces react to interrogation by probes, landers, rovers, and penetrators, remain largely unknown, and therefore landing on an asteroid and manipulating its surface material remains a daunting challenge. The AOSAT+ design is a 12U CubeSat that will be in Low-Earth Orbit (LEO) and that will operate as a spinning on-orbit centrifuge. Part of this 12U CubeSat will contain a laboratory that will recreate asteroid surface conditions using crushed meteorite as a regolith proxy. The spinning of the laboratory will simulate the surface gravity of asteroids 2 km and smaller. The result is a bed of realistic regolith, the environment that landers and diggers and maybe astronauts will interact with. A crucial component of this mission involves the reproduction of the experimental results in numerical simulation in order to extract the material parameters of the regolith and its behavior in a sustained, very low but nonzero-gravity environment.

Exploration of terrestrial planets such as Mars are conducted using orbiters, landers and rovers. Cameras and instruments onboard orbiters have enabled global mapping of Mars at low spatial resolution. Landers and rovers such as the Mars Science Laboratory (MSL) carry state-of-the-art instruments to characterize small localized areas. This leaves a critical gap in exploration capabilities: mapping regions in the hundreds of kilometers range. In this paper, we extend our work on CubeSat-sized sailplanes with detailed design studies of different aircraft configurations and payloads, identifying generalized design principles for autonomous sailplane-based surface reconnaissance and science applications. We further analyze potential wing deployment technologies, including conventional inflatables with hardened membranes, use of composite inflatables, and quick-setting foam. We perform detailed modeling of the Martian atmosphere and possible flight patterns at Jerezo crater using the Mars Regional Atmospheric Modeling System (MRAMS) to provide realistic atmospheric conditions at the landing site for NASA's 2020 rover. We revisit the feasibility of the Mars Sailplane concept, comparing it to previously proposed solutions, and identifying pathways to build laboratory prototypes for high-altitude Earth based testing. Finally, our work will analyze the implications of this technology for exploring other planetary bodies with atmospheres, including Venus and Titan.

There is growing demand for satellite swarms and constellations for global positioning, remote sensing and relay communication in higher LEO orbits. This will result in many obsolete, damaged and abandoned satellites that will remain on-orbit beyond 25 years. These abandoned satellites and space debris maybe economically valuable orbital real-estate and resources that can be reused, repaired or upgraded for future use. Space traffic management is critical to repair damaged satellites, divert satellites into warehouse orbits and effectively de-orbit satellites and space debris that are beyond repair and salvage. Current methods for on-orbit capture, servicing and repair require a large service satellite. However, by accessing abandoned satellites and space debris, there is an inherent heightened risk of damage to a servicing spacecraft. Sending multiple small-robots with each robot specialized in a specific task is a credible alternative, as the system is simple and cost-effective and where loss of one or more robots does not end the mission. In this work, we outline an end to end multirobot system to capture damaged and abandoned spacecraft for salvaging, repair and for de-orbiting. We analyze the feasibility of sending multiple, decentralized robots that can work cooperatively to perform capture of the target satellite as a first step, followed by crawling onto damage satellites to perform detailed mapping. After obtaining a detailed map of the satellite, the robots will proceed to either repair and replace or dismantle components for salvage operations. Finally, the remaining components will be packaged with a de-orbit device for accelerated de-orbit.

Exploration of Mars has been made possible using a series of landers, rovers and orbiters. The HiRise camera on the Mars Reconnaissance Orbiter (MRO) has captured high-resolution images covering large tracts of the surface. However, orbital images lack the depth and rich detail obtained from in-situ exploration. Rovers such as Mars Science Laboratory and upcoming Mars 2020 carry state-of-the-art science laboratories to perform in-situ exploration and analysis. However, they can only cover a small area of Mars through the course of their mission. A critical capability gap exists in our ability to image, provide services and explore large tracts of the surface of Mars required for enabling a future human mission. A promising solution is to develop a reconnaissance sailplane that travels tens to hundreds of kilometers per sol. The aircraft would be equipped with imagers that provide that in-situ depth of field, with coverage comparable to orbital assets such as MRO. A major challenge is that the Martian carbon dioxide atmosphere is thin, with a pres-sure of 1% of Earth at sea level. To compensate, the aircraft needs to fly at high-velocities and have sufficiently large wing area to generate the required lift. Inflatable wings are an excellent choice as they have the lowest mass and can be used to change shape (morph) depending on aerodynamic or con-trol requirements. In this paper, we present our design of an inflatable sail-plane capable of deploying from a 12U CubeSat platform. A pneumatic de-ployment mechanism ensures highly compact stowage volumes and minimizes complexity.

The science and origins of asteroids is deemed high priority in the Planetary Science Decadal Survey. Major scientific goals for the study of planetesimals are to decipher geological processes in SSSBs not determinable from investigation via in-situ experimentation, and to understand how planetesimals contribute to the formation of planets. Ground based observations are not sufficient to examine SSSBs, as they are only able to measure what is on the surface of the body; however, in-situ analysis allows for further, close up investigation as to the surface characteristics and the inner composure of the body. To this end, the Asteroid Mobile Imager and Geologic Observer (AMIGO) an autonomous semi-inflatable robot will operate in a swarm to efficiently characterize the surface of an asteroid. The stowed package is 10x10x10 cm (equivalent to a 1U CubeSat) that deploys an inflatable sphere of ~1m in diameter. Three mobility modes are identified and designed: ballistic hopping, rotation during hops, and up-righting maneuvers. Ballistic hops provide the AMIGO robot the ability to explore a larger portion of the asteroid's surface to sample a larger area than a stationary lander. Rotation during the hop entails attitude control of the robot, utilizing propulsion and reaction wheel actuation. In the event of the robot tipping or not landing up-right, a combination of thrusters and reaction wheels will correct the robot's attitude. The AMIGO propulsion system utilizes sublimate-based micro-electromechanical systems (MEMS) technology as a means of lightweight, low-thrust ballistic hopping and coarse attitude control. Each deployed AMIGO will hop across the surface of the asteroid multiple times.

The exponential rise in small-satellites and CubeSats in Low Earth Orbit (LEO) poses important challenges for future space traffic management. At altitudes of 600 km and lower, aerodynamic drag accelerates de-orbiting of satellites. However, placement of satellites at higher altitudes required for constellations pose important challenges. The satellites will require on-board propulsion to lower their orbits to 600 km and let aerodynamic drag take-over. In this work we analyze solutions for de-orbiting satellites at altitudes of up to 3000 km. We consider a modular robotic de-orbit device that has stowed volume of a regular CubeSat. The de-orbit device would be externally directed towards a dead satellite or placed on one by an external satellite servicing system. Our solutions are intended to be simple, high-reliability devices that operate in a passive manner, requiring no active electronics or utilize external beamed power in the form of radio frequency, microwave or laser to operate. Utilizing this approach, it is possible for an external, even ground based system to direct the de-orbit of a spacecraft. The role of an external system to direct the de-orbit is important to avoid accidental collisions. Some form of propulsion is needed to lower the orbit of the dead satellite or orbital debris. We considered green (non-toxic) propulsion methods including solar radiation pressure, solar-thermal propulsion using water steam, solar-electrolysis propulsion using water and use of electrodynamic tethers. Based on this trade-study we identify multiple solutions that can be used to de-orbit a spacecraft or orbital debris.

There is an every-growing need to construct large space telescopes and structures for observation of exo-planets, main-belt asteroids and NEOs. Space observation capabilities can significant enhanced by large-aperture structures. Structures extending to several meters in size could potentially revolutionize observation enabling technologies. These include star-shades for imaging distant objects such as exo-planets and high-resolution large aperture telescopes. In addition to size, such structures require controllable precision surfaces and high packing efficiencies. A promising approach to achieving high compaction for large surface areas is by incorporating compliant materials or gossamers. Gossamer structures on their own do not meet stiffness requirements for controlled deployment. Supporting stiffening mechanisms are required to fully realize their structural potential. The accuracy of the 'active' surface constructed out of a gossamer additionally also depends on the load bearing structure that supports it. This paper investigates structural assemblies constructed from modular inflatable membranes stiffened pneumatically using inflation gas. These units assembled into composites can yield desirable characteristics. We present the design of large assemblies of these modular elements.

Small-satellites and CubeSats offer a low-cost pathway to access Low Earth Orbit at altitudes of 450 km and lower thanks to miniaturization and advancement in reliability of commercial electronics. However, at these low altitudes, atmospheric drag has a critical effect on the satellite resulting in natural deorbits within months. As these small systems further increase in reliability and radiation tolerance they will be able readily access higher orbits at altitudes of 700 km and higher, where atmospheric drag has little to no effect. This requires alternative technologies to either de-orbit these small spacecrafts at the end of life or move them to a safe parking orbit. Use of propulsion and de-orbit mechanisms have been proposed, however they require active control systems to be trigged. Other typical de-orbit mechanism relies on complex mechanisms with many moving parts. In this work, we analyze the feasibility of using inflatable de-orbit devices that are triggered passively when a spacecraft is tumbling. Inflatables have already been proposed as hypersonic deccelerators that would carry large payload to the Martian surface. However, these systems are quite complex and need to withstand high-forces, temperature and enable survival of a critical payload. Furthermore, inflatables have been proposed as communication antennas and as structures using a class of sublimates that turn into gas under the vacuum of space. These inflatables system are relatively simple and does not require a specialized inflation system.

We advocate a low-cost strategy for long-duration research into the 'milligravity' environment of asteroids, comets and small moons, where surface gravity is a vector field typically less than 1/1000 the gravity of Earth. Unlike the microgravity environment of space, there is a directionality that gives rise, over time, to strangely familiar geologic textures and landforms. In addition to advancing planetary science, and furthering technologies for hazardous asteroid mitigation and in-situ resource utilization, simplified access to long-duration milligravity offers significant potential for advancing human spaceflight, biomedicine and manufacturing. We show that a commodity 3U ($10\times10\times34$ cm$^3$) cubesat containing a laboratory of loose materials can be spun to 1 rpm = $2\pi/60$ s$^{-1}$ on its long axis, creating a centrifugal force equivalent to the surface gravity of a kilometer-sized asteroid. We describe the first flight demonstration, where small meteorite fragments will pile up to create a patch of real regolith under realistic asteroid conditions, paving the way for subsequent missions where landing and mobility technology can be flight-proven in the operational environment, in Low-Earth Orbit (LEO). The 3U design can be adapted for use onboard the International Space Station (ISS) to allow for variable gravity experiments under ambient temperature and pressure for a broader range of experiments.

The effect of fractal space time of the quantum particles on the variation of the fine structure constant $\alpha$ has been studied. The variation of fine structure constant has been investigated around De Broglie length $\lambda$ and compton length $\lambda_{c}$ and it has been suggested that the variation may be attributed to the dimensional transition of the particle trajectories between these two quantum domains. Considering the Fractal universe with a small inhomogeneity in the mass distribution in the early universe, the variation of the fine structure constant have been investigated between matter and radiation dominated era. The fine structure constant shows a critical behaviour with critical exponent which is fractional and shows a discontinuity. It has been suggested that the variation of the fine structure constant may be attributed to the intrinsic scale dependance of the fundamental constants of nature.

The shell-to-shell energy transfer rates for magnetohydrodynamic (MHD) turbulence are computed analytically, which shows local energy transfer rates from velocity to velocity, velocity to magnetic, magnetic to velocity, and magnetic to magnetic fields for nonhelical MHD in the inertial range. It is also found that for kinetic-energy dominated MHD fluid, there is a preferential shell-to-shell energy transfer from kinetic to magnetic energy; the transfer is reversed for magnetic-energy dominated MHD fluid. This property is the reason for the asymptotic value of Alfven ratio to be close to 0.5. The analytical results are in close agreement with recent numerical results. When magnetic and kinetic helicities are turned on, the helical contributions are opposite to the corresponding nonhelical contributions. The helical energy transfers have significant nonlocal components.

An interferometer system for use at the 2.34 meter Vainu Bappu Telescope (VBT), situated at Vainu Bappu Observatory (VBO), Kavalur, to obtain speckle-grams of astronomical objects in the visible wavelength, has been developed. Laboratory tests of resultant intensity distributions due to a point source, with phase modulation screens, as well as the images obtained using this interferometer at the cassegrain end of the said telescope are discussed.

A new optical speckle interferometer for use at the 2.34 meter Vainu Bappu Telescope (VBT), at Vainu Bappu Observatory (VBO), Kavalur, India, has been designed and developed. Provisions have been made for observation both at the prime focus (f/3.25), as well as at the Cassegrain focus (f/13) of the said telescope. The technical details of this sensitive instrument and the design features are described. An interface between the telescope and the afore-mentioned interferometer is made based on a concept of eliminating the formation of eddies due to the hot air entrapment. The performances of this instrument has been tested both at the laboratory, as well as at the Cassegrain end of the telescope. It is being used routinely to observe the speckle-grams of close-binary (separation $<$1 arc second) stars. The size of the Fried's parameter, r$_{o}$, is also measured.