The High Energy Stereoscopic System (H.E.S.S.) is one of the three arrays of imaging atmospheric Cherenkov telescopes (IACTs) currently in operation. It is composed of four 12-meter telescopes and a 28-meter one, and is sensitive to gamma rays in the energy range ~30 GeV - 100 TeV. The cameras of the 12-m telescopes recently underwent a substantial upgrade, with the goal of improving their performance and robustness. The upgrade involved replacing all camera components except for the photomultiplier tubes (PMTs). This meant developing new hardware for the trigger, readout, power, cooling and mechanical systems, and new software for camera control and data acquisition. Several novel technologies were employed in the cameras: the readout is built around the new NECTAr digitizer chip, developed for the next generation of IACTs; the camera electronics is fully controlled and read out via Ethernet using a combination of FPGA and embedded ARM computers; the software uses modern libraries such as Apache Thrift, ZMQ and Protocol buffers. This work describes in detail the design and the performance of the upgraded cameras.

The 14 years old cameras of the H.E.S.S. 12-m telescopes have been upgraded in 2015/2016, with the goals of reducing the system failure rate, reducing the dead time and improving the overall performance of the array. This conference contribution describes the various tests that were carried out on the cameras and their sub-components both in the lab and on site. It also gives an overview of the commissioning and calibration procedures adopted during and after the installation, including e.g. flat-fielding and trigger threshold scans. Finally, it reports in detail about the overall performance of the four new H.E.S.S. I cameras, using very recent data.

In 2015/16, the photomultiplier cameras of the H.E.S.S. Cherenkov telescopes CT1-4 have undergone a major upgrade. The entire electronics has been replaced, using NECTAr chips for the front-end readout. A new ventilation system has been installed and several auxiliary components have been replaced. Besides this, the internal control and readout software was rewritten from scratch in a modern and modular way. Ethernet technology was used wherever possible to ensure both flexibility, stability and high bandwidth. An overview of the installed components will be given.

The High Energy Stereoscopic System (H.E.S.S.) is an array of imaging atmospheric Cherenkov telescopes (IACTs) located in the Khomas Highland in Namibia. It consists of four 12-m telescopes (CT1-4), which started operations in 2003, and a 28-m diameter one (CT5), which was brought online in 2012. It is the only IACT system featuring telescopes of different sizes, which provides sensitivity for gamma rays across a very wide energy range, from ~30 GeV up to ~100 TeV. Since the camera electronics of CT1-4 are much older than the one of CT5, an upgrade is being carried out; first deployment was in 2015, full operation is planned for 2016. The goals of this upgrade are threefold: reducing the dead time of the cameras, improving the overall performance of the array and reducing the system failure rate related to aging. Upon completion, the upgrade will assure the continuous operation of H.E.S.S. at its full sensitivity until and possibly beyond the advent of CTA. In the design of the new components, several CTA concepts and technologies were used and are thus being evaluated in the field: The upgraded read-out electronics is based on the NECTAR readout chips; the new camera front- and back-end control subsystems are based on an FPGA and an embedded ARM computer; the communication between subsystems is based on standard Ethernet technologies. These hardware solutions offer good performance, robustness and flexibility. The design of the new cameras is reported here.

The Scientific Trigger Unit (UTS) is a satellite equipment designed to detect Gamma Ray Bursts (GRBs) observed by the onboard 6400 pixels camera ECLAIRs. It is foreseen to equip the low-Earth orbit French-Chinese satellite SVOM and acts as the GRB trigger unit for the mission. The UTS analyses in real-time and in great details the onboard camera data in order to select the GRBs, to trigger a spacecraft slew re-centering each GRB for the narrow field-of-view instruments, and to alert the ground telescope network for GRB follow-up observations. A few GRBs per week are expected to be observed by the camera; the UTS targets a close to 100% trigger efficiency, while being selective enough to avoid fake alerts. This is achieved by running the complex scientific algorithms on a radiation tolerant hardware, based on a FPGA data pre-processor and a CPU with a Real-Time Operating System. The UTS is a scientific software, firmware and hardware co-development. A Data Processing Model (DPM) has been developed to fully validate all the technical choices deeply impacted by the ITAR restriction applied to the development. The DPM permits to evaluate the processing power and the memory bandwidth, and to adjust the balance load between software and firmware. This paper presents the UTS DPM functionalities and architecture. It highlights the results obtained with the full GRB trigger algorithms implemented on a rad-tolerant ITAR-free processor.