This paper reports the characterization of hollow metallic waveguides (HMW) to be used as single-mode wavefront filters for nulling interferometry in the 6-20 microns range. The measurements presented here were performed using both single-mode and multimode conductive waveguides at 10.6 microns. We found propagation losses of about 16dB/mm, which are mainly due to the theoretical skin effect absorption in addition to the roughness of the waveguide metallic walls. The input and output coupling efficiency of our samples has been improved by adding tapers to minimize the impedance mismatch. A proper distinction between propagation losses and coupling losses is presented. Despite their elevate propagation losses, HMW show excellent spatial filtering capabilities in a spectral range where photonics technologies are only emerging.

Nulling interferometry is a technique providing high angular resolution which is the core of the space missions Darwin and the Terrestrail Planet Finder. The first objective is to reach a deep degree of starlight cancelation in the range 6 -- 20 microns, in order to observe and to characterize the signal from an Earth-like planet. Among the numerous technological challenges involved in these missions, the question of the beam combination and wavefront filtering has an important place. A single-mode integrated optics (IO) beam combiner could support both the functions of filtering and the interferometric combination, simplifying the instrumental design. Such a perspective has been explored in this work within the project Integrated Optics for Darwin (IODA), which aims at developing a first IO combiner in the mid-infrared. The solutions reviewed here to manufacture the combiner are based on infrared dielectric materials on one side, and on metallic conductive waveguides on the other side. With this work, additional inputs are offered to pursue the investigation on mid-infrared photonics devices.

Aims: In the context of space interferometry missions devoted to the search of exo-Earths, this paper investigates the capabilities of new single mode conductive waveguides at providing modal filtering in an infrared and monochromatic nulling experiment; Methods: A Michelson laser interferometer with a co-axial beam combination scheme at 10.6 microns is used. After introducing a Pi phase shift using a translating mirror, dynamic and static measurements of the nulling ratio are performed in the two cases where modal filtering is implemented and suppressed. No additional active control of the wavefront errors is involved. Results: We achieve on average a statistical nulling ratio of 2.5e-4 with a 1-sigma upper limit of 6e-4, while a best null of 5.6e-5 is obtained in static mode. At the moment, the impact of external vibrations limits our ability to maintain the null to 10 to 20 seconds.; Conclusions: A positive effect of SM conductive waveguide on modal filtering has been observed in this study. Further improvement of the null should be possible with proper mechanical isolation of the setup.

Nulling interferometry is an astronomical technique that combines equal wavefronts to achieve a deep rejection ratio of an on-axis star, and that could permit to detect Earth-like planets in the mid-infrared band 5 -- 20 microns. Similarly to what is done in the near-infrared, high frequencies spatial filtering of the incoming beams can be achieved using single-mode waveguides operating in the mid-infrared. An appreciable reduction of the instrumental complexity is also possible using integrated optics (IO) devices in this spectral range. The relative lack of single-mode guided optics in the mid-infrared has motivated the present technological study to demonstrate the feasibility of dielectric waveguides functioning at longer wavelengths. We propose to use selenide and telluride components to pursue the development of more complex IO functions.

This paper presents the work achieved for the manufacturing and characterization of first single-mode waveguides to be used as modal filters for nulling interferometry in the mid-infrared range [4-20 um]. As very high dynamic range is mandatory for detection of Earth-like planets, modal filtering is one of the most stringent instrumental aspects. The hollow metallic waveguides (HMW) presented here are manufactured using micro-machining techniques. Single-mode behavior has been investigated in laboratory through a technique of polarization analysis while transmission features have been measured using flux relative comparison. The single-mode behavior have been assessed at lambda=10.6 um for rectangular waveguides with dimensions a=10 um and b<5.3 um with an accuracy of ~2.5 %. The tests have shown that a single-polarization state can be maintained in the waveguide. A comparison with results on multi-mode HMW is proposed. Excess losses of 2.4 dB (~ 58 % transmission) have been measured for a single-mode waveguide. In particular, the importance of coupling conditions into the waveguide is emphasized here. The goal of manufacturing and characterizing the first single-mode HMW for the mid-infrared has been achieved. This opens the road to the use of integrated optics for interferometry in the mentioned spectral range.