Single-ended circuit topologies, and a theorem for the development thereof, are presented with which one may realize constant-resistance (or reflectionless) filters, having ideally zero reflection coefficient at all frequencies and from all ports, suitable for elliptic and pseudo-elliptic filter responses. The proposed theorem produces topologies of a type known as the coupled-ladder, which has been previously studied for only polynomial responses (e.g. Butterworth, Chebyshev, etc.). A comparison between these topologies and another classical approach known as the economy bridge reveals that those proposed here have a number of theoretical and practical advantages. The theory is tested by the construction of a sixth-order, low-pass reflectionless filter exhibiting a pseudo-elliptic frequency response. Measured results are in excellent agreement with theory, and show return loss better than 20 dB throughout the pass-band, the transition-band, and up to two octaves into the stop-band.

Modifications of the authors' previously-published, generalized, lumped-element, reflectionless filter topologies are presented which remove the original constraints on the relative values of its prototype parameters. Thus, any transfer function which can be realized as the transmission or reflection coefficient of a conventional ladder prototype may now be implemented in reflectionless form --- that is, having the same transfer function in transmission but with identically zero reflection coefficient at both ports and at all frequencies from DC to infinity, given ideal elements. The theoretical basis of these modifications is explained, and then tested via the construction of passive, reflectionless low-pass filter prototypes that, in the prior topology, would have required negative reactive elements. The results show excellent agreement with theory.

A new 1.4 GHz 19-element, dual-polarization, cryogenic phased array feed (PAF) radio astronomy receiver has been developed for the Robert C. Byrd Green Bank Telescope (GBT) as part of FLAG (Focal L-band Array for the GBT) project. Commissioning observations of calibrator radio sources show that this receiver has the lowest reported beamformed system temperature ($T_{\rm sys}$) normalized by aperture efficiency ($\eta$) of any phased array receiver to date. The measured $T_{\rm sys}/\eta$ is $25.4 \pm 2.5$ K near 1350 MHz for the boresight beam, which is comparable to the performance of the current 1.4 GHz cryogenic single feed receiver on the GBT. The degradation in $T_{\rm sys}/\eta$ at $\sim$ 4 arcmin (required for Nyquist sampling) and $\sim$ 8 arcmin offsets from the boresight is, respectively, $\sim$ 1\% and $\sim$ 20\% of the boresight value. The survey speed of the PAF with seven formed beams is larger by a factor between 2.1 and 7 compared to a single beam system depending on the observing application. The measured performance, both in frequency and offset from boresight, qualitatively agree with predictions from a rigorous electromagnetic model of the PAF. The astronomical utility of the receiver is demonstrated by observations of the pulsar B0329+54 and an extended HII region, the Rosette Nebula. The enhanced survey speed with the new PAF receiver will enable the GBT to carry out exciting new science, such as more efficient observations of diffuse, extended neutral hydrogen emission from galactic in-flows and searches for Fast Radio Bursts.

In this paper, we describe the development of a new L-band (1.4 GHz) Cryogenic Phased Array Feed (PAF) system, referred to as the GBT2 array. Results from initial measurements made with the GBT2 array are also presented. The PAF was developed for the Green Bank Telescope (GBT) as part of the Focal L-band Array for the GBT (FLAG) project. During the first stage of the development work (Phase I), a prototype cryogenic 19 element dual-polarized array with "Kite" dipole elements was developed and tested on the GBT. The measured system temperature over efficiency ($T_{sys}/\eta$) ratio for the bore sight beam of the Kite array was 45.5 K at 1.55 GHz. The off-boresight $T_{sys}/\eta$ shows an increase by 13 K at an offset equal to the half power beam width (7$^{'}$.2 at 1.7 GHz). Our measurements indicate that the off-boresight degradation and field-of-view (FoV) limitation of the Kite array is simply due to the fixed array size. To increase the FoV, a new 19-element GBT2 array with larger array spacing was developed during FLAG Phase II. The frequency response of the array was optimized from 1.2 to 1.6 GHz. A system with larger cryostat, new low noise amplifiers (LNAs), down-conversion and digitization close to the front end, unformatted digital transmission over fiber, ROACH II based polyphase filter banks (PFBs) with bandwidth 150 MHz and a data acquisition system that records voltage samples from one of the PFB channels were all developed. The data presented here is processed off-line. The receiver temperature measured with the new system is 17 K at 1.4 GHz, an improvement $>$ 8 K over the previous Kite array. Measurements with the GBT2 array on the telescope are in progress. A real time 150 MHz beamformer is also being developed as part of an NSF-funded collaboration between NRAO/GBO/BYU \& West Virginia University (Beamformer Project) to support science observations.

We report on the development and characterization of a compact, full-waveguide bandwidth (WR-10) signal source for general-purpose testing of mm-wave components. The MMIC-based multichip module is designed for compactness and ease-of-use, especially in size-constrained test sets such as a wafer probe station. It takes as input a cm-wave CW reference and provides a factor of three frequency multiplication as well as amplification, output power adjustment, and in-situ output power monitoring. It utilizes a number of custom MMIC chips such as a Schottky-diode limiter and a broadband mm-wave detector, both designed explicitly for this module, as well as custom millimeter-wave multipliers and amplifiers reported in previous papers.

The design, fabrication, and measurement of a coax to double-ridged waveguide launcher and horn antenna is presented. The novel launcher design employs two symmetric field probes across the ridge gap to minimize spreading inductance in the transition, and achieves better than 15 dB return loss over a 10:1 bandwidth. The aperture-matched horn uses a half-cosine transition into a linear taper for the outer waveguide dimensions and ridge width, and a power-law scaled gap in order to realize monotonically-varying cutoff frequencies, thus avoiding the appearance of trapped mode resonances. It achieves a nearly constant beamwidth in both E- and H-planes for an overall directivity of about 16.5 dB from 10-100 GHz.

This paper expands on the previously described reflectionless filters - that is, filters having, in principle, identically-zero reflection coefficient at all frequencies - by introducing a wide variety of new reflectionless structures that were not part of the original publication. In addition to extending the lumped-element derivation to include transmission line filters, this is achieved by the introduction of a novel method wherein the left- and right-hand side stop-band terminations are coupled to each other using a two-port sub-network. Specific examples of the sub-network are given which increase the stop-band attenuation per filter cell and steepen the cutoff response without disrupting the reflectionless property or increasing the insertion-loss in the pass-band. It is noteworthy that a common feature of all the structures derived by these methods is that most, if not all, of the reactive elements are of equal normalized value. This greatly simplifies the tuning requirements, and has facilitated their implementation as monolithic microwave integrated circuits (MMICs). A number of examples of MMIC reflectionless filters constructed in this way are presented and their results compared to the theory.

In this paper we present a novel class of compact orthomode transducers which use digital calibration to synthesize the desired polarization vectors while maintaining high isolation and minimizing mass and volume. These digital orthomode transducers consist of an arbitrary number of planar probes in a circular waveguide, each of which is connected to an independent receiver chain designed for stability of complex gain. The outputs of each receiver chain are then digitized and combined numerically with calibrated, complex coefficients. Measurements on two prototype digital orthomode transducers, one with three probes and one with four, show better than 50 dB polarization isolation over a 10 C temperature range with a single calibration.

A design methodology and synthesis equations are described for lumped-element filter prototypes having low-pass, high-pass, band-pass, or band-stop characteristics with theoretically perfect input- and output-match at all frequencies. Such filters are a useful building block in a wide variety of systems in which the highly reactive out-of-band termination presented by a conventional filter is undesirable. The filter topology is first derived from basic principles. Then the relative merits of several implementations and tunings are compared via simulation. Finally, measured data on low-pass and band-pass filter examples are presented which illustrate the practical advantages as well as showing excellent agreement between measurement and theory.