We present a new way to mitigate focal-ratio degradation (FRD) when using optical fibers to transport multimode light. Our approach exploits a custom multicore fiber (MCF) with six dissimilar cores that are single mode at ~1550 nm wavelength and minimally coupled over 7 m. We fabricated adiabatic mode-selective photonic lanterns (PLs) at each end of the MCF to create a fiber link with multimode ports, the PLs coupling each spatial mode of the multimode ports to a specific core of the MCF and vice versa. The PL-MCF-PL link exhibits superior FRD behavior compared to a conventional multimode fiber that also supports 6 modes, because it inhibits the transfer of light from lower-order modes to higher-order modes. These results open up a potentially powerful new approach to mitigate FRD in multimode fiber links, with particular applications in astronomical instruments.

Recently, we demonstrated how an astrophotonic light reformatting device, based on a multicore fibre photonic lantern and a three-dimensional waveguide component, can be used to efficiently reformat the point spread function of a telescope to a diffraction-limited psuedo-slit [arXiv:1512.07309]. Here, we demonstrate how such a device can also efficiently mitigate modal noise -- a potential source of instability in high resolution multi-mode fibre-fed spectrographs). To investigate the modal noise performance of the photonic reformatter, we have used it to feed light into a bench-top near-infrared spectrograph (R {\approx} 9,500, {\lambda} {\approx} 1550 nm). One approach to quantifying the modal noise involved the use of broadband excitation light and a statistical analysis of how the overall measured spectrum was affected by variations in the input coupling conditions. This approach indicated that the photonic reformatter could reduce modal noise by a factor of six when compared to a multi-mode fibre with a similar number of guided modes. Another approach to quantifying the modal noise involved the use of multiple spectrally narrow lines, and an analysis of how the measured barycentres of these lines were affected by variations in the input coupling. Using this approach, the photonic reformatter was observed to suppress modal noise to the level necessary to obtain spectra with stability close to that observed when using a single mode fibre feed. These results demonstrate the potential of using photonic reformatters to enable efficient multi-mode spectrographs that operate at the diffraction limit and are free of modal noise, with potential applications including radial velocity measurements of M-dwarfs.

Envisioning more compact and cost accessible astronomical instruments is now possible with existing photonic technologies like specialty optical fibres, photonic lanterns and ultrafast laser inscribed chips. We present an original design of a multicore fibre (MCF) terminated with multimode photonic lantern ports. It is designed to act as a relay fibre with the coupling effciency of a multimode fibre, modal stability similar to a single-mode fibre and low loss in a wide range of wavelengths (380 nm to 860 nm). It provides phase and amplitude scrambling to achieve a stable near field and far field output illumination pattern despite input coupling variations, and low modal noise for increased photometric stability for high signal-to-noise applications such as precision radial velocity (PRV) science. Preliminary results are presented for a 511-core MCF and compared with current state of the art octagonal fibre.

This paper reports on the modal noise characterisation of a hybrid reformatter. The device consists of a multicore-fibre photonic lantern and an ultrafast laser-inscribed slit reformatter. It operates around 1550 nm and supports 92 modes. Photonic lanterns transform a multimode signal into an array of single-mode signals, and thus combine the high coupling efficiency of multimode fibres with the diffraction-limited performance of single-mode fibres. This paper presents experimental measurements of the device point spread function properties under different coupling conditions, and its throughput behaviour at high spectral resolution. The device demonstrates excellent scrambling but its point spread function is not completely stable. Mode field diameter and mode barycentre position at the device output vary as the multicore-fibre is agitated due to the fabrication imperfections.

The spectral resolution of a dispersive astronomical spectrograph is limited by the trade-off between throughput and the width of the entrance slit. Photonic guided-wave transitions have been proposed as a route to bypass this trade-off, by enabling the efficient reformatting of incoherent seeing-limited light collected by the telescope into a linear array of single modes: a pseudo-slit which is highly multimode in one axis but diffraction-limited in the dispersion axis of the spectrograph. It is anticipated that the size of a single-object spectrograph fed with light in this manner would be essentially independent of the telescope aperture size. A further anticipated benefit is that such spectrographs would be free of `modal noise', a phenomenon that occurs in high-resolution multimode fibre-fed spectrographs due to the coherent nature of the telescope point-spread-function (PSF). We address these aspects by integrating a multicore fibre photonic lantern with an ultrafast laser inscribed three-dimensional waveguide interconnect to spatially reformat the modes within the PSF into a diffraction-limited pseudo-slit. Using the CANARY adaptive optics (AO) demonstrator on the William Herschel Telescope, and 1530 $\pm$ 80 nm stellar light, the device is found to exhibit a transmission of 47-53 % depending upon the mode of AO correction applied. We also show the advantage of using AO to couple light into such a device by sampling only the core of the CANARY PSF. This result underscores the possibility that a fully-optimised guided-wave device can be used with AO to provide efficient spectroscopy at high spectral resolution.

Using ultrafast laser inscription, we report the fabrication of a prototype three-dimensional 121-waveguide fan-out device capable of reformatting the output of a 120 core multicore fiber (MCF) into a one-dimensional linear array. When used in conjunction with an actual MCF, we demonstrate that the reformatting function using this prototype would result in an overall throughput loss of approximately 7.0 dB. However, if perfect coupling from the MCF into the fan-out could be achieved, the reformatting function would result in an overall loss of only approximately 1.7 dB. With adequate development, similar devices could efficiently reformat the output of so-called "photonic lanterns" fabricated using highly multicore fibers.

A long-standing and profound problem in astronomy is the difficulty in obtaining deep near-infrared observations due to the extreme brightness and variability of the night sky at these wavelengths. A solution to this problem is crucial if we are to obtain the deepest possible observations of the early Universe since redshifted starlight from distant galaxies appears at these wavelengths. The atmospheric emission between 1000 nm and 1800 nm arises almost entirely from a forest of extremely bright, very narrow hydroxyl emission lines that varies on timescales of minutes. The astronomical community has long envisaged the prospect of selectively removing these lines, while retaining high throughput between the lines. Here we demonstrate such a filter for the first time, presenting results from the first on-sky tests. Its use on current 8m telescopes and future 30m telescopes will open up many new research avenues in the years to come.