Context. The wind driven halo is a feature observed within the images delivered by the latest generation of ground-based instruments equipped with an extreme adaptive optics system and a coronagraphic device, such as SPHERE at the VLT. This signature appears when the atmospheric turbulence conditions are varying faster than the adaptive optics loop can correct. The wind driven halo shows as a radial extension of the point spread function along a distinct direction (sometimes referred to as the butterfly pattern). When present, it significantly limits the contrast capabilities of the instrument and prevents the extraction of signals at close separation or extended signals such as circumstellar disks. This limitation is consequential because it contaminates the data a substantial fraction of the time: about 30% of the data produced by the VLT/SPHERE instrument are affected by the wind driven halo.Aims. This paper reviews the causes of the wind driven halo and presents a method to analyze its contribution directly from the scientific images. Its effect on the raw contrast and on the final contrast after post-processing is demonstrated.Methods. We used simulations and on-sky SPHERE data to verify that the parameters extracted with our method are capable of describing the wind driven halo present in the images. We studied the temporal, spatial and spectral variation of these parameters to point out its deleterious effect on the final contrast.Results. The data driven analysis we propose does provide information to accurately describe the wind driven halo contribution in the images. This analysis justifies why this is a fundamental limitation to the final contrast performance reached.Conclusions. With the established procedure, we will analyze a large sample of data delivered by SPHERE in order to propose, in the future, post-processing techniques tailored to remove the wind driven halo.

Modern extreme adaptive optics (AO) systems achieving diffraction-limited performance open up new possibilities for instrumentation. Especially important for the fields of spectroscopy and interferometry is that it enables the prospect to couple light into single-mode fibers (SMFs). However, due to their small size, efficient coupling is very sensitive to the quality of the fiber alignment, beam drifts and higher-frequency tip-tilt aberrations caused by telescope mechanics and vibrations. These residual aberrations are not always sensed and corrected by the AO system, leading to unacceptable losses. This is particularly severe for the Extremely Large Telescopes, where their huge structure will mean vibrations increase and optimal AO solutions are even more difficult to implement. We have created a focal plane sensor to correct for residual aberrations by surrounding the SMF with six Multi-mode fibers (MMFs). On each of the MMFs sits a printed freeform lens, making up a six-element micro-lens ring to refract the light into these surrounding MMFs and thus minimizing light loss in the gap between the fiber cores. This means when the beam is near diffraction limited and centered almost all light couples to the SMF. When the beam is misaligned, it couples to the surrounding cores, which are read out by a detector and processed by the DARC software driving a tip-tilt mirror. Currently we are aiming to detect and correct only tip-tilt aberrations. However, choosing to surround the central fiber with six sensing locations potentially allows us to investigate higher order correction modes. Here we present the design and performance our prototype system. This has been designed for use with the iLocater fiber injection system at the LBT and can easily be scaled to larger telescopes. We present test results from the KOOL laboratory and initial integration with the iLocater instrument.

Focus anisoplanatism is a significant measurement error when using one single laser guide star (LGS) in an Adaptive Optics (AO) system, especially for the next generation of extremely large telescopes. An alternative LGS configuration, called Projected Pupil Plane Pattern (PPPP) solves this problem by launching a collimated laser beam across the full pupil of the telescope. If using a linear, modal reconstructor, the high laser power requirement ($\sim1000\,\mbox{W}$) renders PPPP uncompetitive with Laser Tomography AO. This work discusses easing the laser power requirements by using an artificial Neural Network (NN) as a non-linear reconstructor. We find that the non-linear NN reduces the required measurement signal-to-noise ratio (SNR) significantly to reduce PPPP laser power requirements to $\sim200\,\mbox{W}$ for useful residual wavefront error (WFE). At this power level, the WFE becomes 160\,nm root mean square (RMS) and 125\,nm RMS when $r_0=0.098$\,m and $0.171$\,m respectively for turbulence profiles which are representative of conditions at the ESO Paranal observatory. In addition, it is shown that as a non-linear reconstructor, a NN can perform useful wavefront sensing using a beam-profile from one height as the input instead of the two profiles required as a minimum by the linear reconstructor.

Atmospheric profiling is a requirement for controlling wide-field Adaptive Optics (AO) instruments, analyzing the AO performance with respect to the observing conditions and predicting the Point Spread Function (PSF) spatial variations. We present PEPITO, a new concept for profiling atmospheric turbulence from {\em post~facto} tip-tilt (TT) corrected short-exposure images. PEPITO utilizes the anisokinetism effect in the images between several stars separated from a reference star, and then produces the profile estimation using a model-fitting methodology, by fitting to the long exposure TT-corrected PSF. PEPITO has a high sensitivity to both $C_n^2(h)$ and $L_0(h)$ by relying on the full telescope aperture and a large field of view. It then obtains a high vertical resolution (1\,m-400\,m) configurable by the camera pixel scale, taking advantage of fast statistical convergence (of order of tens of seconds). With only a short exposure-capable large format detector and a numerical complexity independent of the telescope diameter, PEPITO perfectly suits accurate profiling for night optical turbulence site characterization or adaptive optics instruments operations. We demonstrate, in simulation, that the $C_n^2(h)$ and $L_0(h)$ can be estimated to better than 1\% accuracy, from fitted PSFs of magnitude V=11 on a D=0.5\,m telescope with a 10 arcmin field of view.

The latest generation of high contrast instruments dedicated to exoplanets and circumstellar disks imaging are equipped with extreme adaptive optics and coronagraphs to reach contrasts of up to 10^--4 at a few tenths of arc-seconds in the near infrared. The resulting image shows faint features, only revealed with this combination, such as the wind driven halo. The wind driven halo is due to the lag between the adaptive optics correction and the turbulence speed over the telescope pupil. However we observe an asymmetry of this wind driven halo that was not expected when the instrument was designed. In this letter, we describe and demonstrate the physical origin of this asymmetry and support our explanation by simulating the asymmetry with an end-to-end approach. From this work, we found out that the observed asymmetry is explained by the interference between the AO-lag error and scintillation effects, mainly originating from the fast jet stream layer located at about 12 km in altitude. Now identified and interpreted, this effect can be taken into account for further design of high contrast imaging simulators, next generation or upgrade of high contrast instruments, predictive control algorithms for adaptive optics or image post-processing techniques.

The Durham Adaptive Optics Simulation Platform (DASP) is a Monte-Carlo modelling tool used for the simulation of astronomical and solar adaptive optics systems. In recent years, this tool has been used to predict the expected performance of the forthcoming extremely large telescope adaptive optics systems, and has seen the addition of several modules with new features, including Fresnel optics propagation and extended object wavefront sensing. Here, we provide an overview of the features of DASP and the situations in which it can be used. Additionally, the user tools for configuration and control are described.

Recent advances in adaptive optics (AO) have led to the implementation of wide field-of-view AO systems. A number of wide-field AO systems are also planned for the forthcoming Extremely Large Telescopes. Such systems have multiple wavefront sensors of different types, and usually multiple deformable mirrors (DMs). Here, we report on our experience integrating cameras and DMs with the real-time control systems of two wide-field AO systems. These are CANARY, which has been operating on-sky since 2010, and DRAGON, which is a laboratory adaptive optics real-time demonstrator instrument. We detail the issues and difficulties that arose, along with the solutions we developed. We also provide recommendations for consideration when developing future wide-field AO systems.

Laser Guide Stars (LGS) have greatly increased the sky-coverage of Adaptive Optics (AO) systems. Due to the up-link turbulence experienced by LGSs, a Natural Guide Star (NGS) is still required, preventing full sky-coverage. We present a method of obtaining partial tip-tilt information from LGSs alone in multi-LGS tomographic LGS AO systems. The method of LGS up-link tip-tilt determination is derived using a geometric approach, then an alteration to the Learn and Apply algorithm for tomographic AO is made to accommodate up-link tip-tilt. Simulation results are presented, verifying that the technique shows good performance in correcting high altitude tip-tilt, but not that from low altitudes. We suggest that the method is combined with multiple far off-axis tip-tilt NGSs to provide gains in performance and sky-coverage over current tomographic AO systems.

Multi-object adaptive optics (MOAO) has been demonstrated by the CANARY instrument on the William Herschel Telescope. However, for proposed MOAO systems on the next generation Extremely Large Telescopes, such as EAGLE, many challenges remain. Here we investigate requirements that MOAO operation places on deformable mirrors (DMs) using a full end-to-end Monte-Carlo AO simulation code. By taking into consideration a prior global ground-layer (GL) correction, we show that actuator density for the MOAO DMs can be reduced with little performance loss. We note that this reduction is only possible with the addition of a GL DM, whose order is greater than or equal to that of the original MOAO mirrors. The addition of a GL DM of lesser order does not affect system performance (if tip/tilt star sharpening is ignored). We also quantify the maximum mechanical DM stroke requirements (3.5 $\mu$m desired) and provide tolerances for the DM alignment accuracy, both lateral (to within an eighth of a sub-aperture) and rotational (to within 0.2$^\circ$). By presenting results over a range of laser guide star asterism diameters, we ensure that these results are equally applicable for laser tomographic AO systems. We provide the opportunity for significant cost savings to be made in the implementation of MOAO systems, resulting from the lower requirement for DM actuator density.