Modern extreme adaptive optics (AO) systems achieving diffraction-limited performance open up new possibilities for instrumentation. Especially important for the fields of spectroscopy and interferometry is that it enables the prospect to couple light into single-mode fibers (SMFs). However, due to their small size, efficient coupling is very sensitive to the quality of the fiber alignment, beam drifts and higher-frequency tip-tilt aberrations caused by telescope mechanics and vibrations. These residual aberrations are not always sensed and corrected by the AO system, leading to unacceptable losses. This is particularly severe for the Extremely Large Telescopes, where their huge structure will mean vibrations increase and optimal AO solutions are even more difficult to implement. We have created a focal plane sensor to correct for residual aberrations by surrounding the SMF with six Multi-mode fibers (MMFs). On each of the MMFs sits a printed freeform lens, making up a six-element micro-lens ring to refract the light into these surrounding MMFs and thus minimizing light loss in the gap between the fiber cores. This means when the beam is near diffraction limited and centered almost all light couples to the SMF. When the beam is misaligned, it couples to the surrounding cores, which are read out by a detector and processed by the DARC software driving a tip-tilt mirror. Currently we are aiming to detect and correct only tip-tilt aberrations. However, choosing to surround the central fiber with six sensing locations potentially allows us to investigate higher order correction modes. Here we present the design and performance our prototype system. This has been designed for use with the iLocater fiber injection system at the LBT and can easily be scaled to larger telescopes. We present test results from the KOOL laboratory and initial integration with the iLocater instrument.

Closed-loop adaptive optics systems which use minimum mean square error wavefront reconstruction require the computation of pseudo open loop wavefront slopes. These techniques incorporate a knowledge of atmospheric statistics which must therefore be represented within the wavefront slope measurements. These pseudo open loop slopes are computed from the sum of the measured residual slopes and the reconstructed slopes that would be given if the deformable mirror was flat, generally involving the multiplication of an interaction matrix with actuator demands from the previous time-step. When using dense algebra, this multiplication is computationally expensive for Extremely Large Telescopes, requiring a large memory bandwidth. Here we show that this requirement can be significantly reduced, maintaining mathematical correctness and significantly reducing system complexity. This therefore reduces the cost of these systems and increases robustness and reliability.

We propose a many-core CPU architecture for Extremely Large Telescope (ELT) scale adaptive optics (AO) real-time control (RTC) for the multi-conjugate AO (MCAO) and laser-tomographic AO (LTAO) modes. MCAO and LTAO differ from the more conventional single-conjugate (SCAO) mode by requiring more wavefront sensor (WFS) measurements and more deformable mirrors to achieve a wider field of correction, further increasing the computational requirements of ELT-scale AO. We demonstrate results of our CPU based AO RTC operating firstly in SCAO mode, using either Shack-Hartmann or Pyramid style WFS processing, and then in MCAO mode and in LTAO mode using the specifications of the proposed ELT instruments, MAORY and HARMONI. All results are gathered using a CPU based camera simulator utilising UDP packets to better demonstrate the pixel streaming and pipe-lining of the RTC software. We demonstrate the effects of switching parameters, streaming telemetry and implicit pseudo open-loop control (POLC) computation on the MCAO and LTAO modes. We achieve results of < 600$\mu$s latency with an ELT scale SCAO setup using Shack-Hartman processing and < 800$\mu$s latency with SCAO Pyramid WFS processing. We show that our MCAO and LTAO many core CPU architecture can achieve full system latencies of < 1000$\mu$s with jitters < 40$\mu$s RMS. We find that a CPU based AO RTC architecture has a good combination of performance, flexibility and maintainability for ELT-scale AO systems.

Advanced adaptive optics (AO) instruments on ground-based telescopes require accurate knowledge of the atmospheric turbulence strength as a function of altitude. This information assists point spread function reconstruction, AO temporal control techniques and is required by wide-field AO systems to optimize the reconstruction of an observed wavefront. The variability of the atmosphere makes it important to have a measure of the optical turbulence profile in real time. This measurement can be performed by fitting an analytically generated covariance matrix to the cross-covariance of Shack-Hartmann wavefront sensor (SHWFS) centroids. In this study we explore the benefits of reducing cross-covariance data points to a covariance map region of interest (ROI). A technique for using the covariance map ROI to measure and compensate for SHWFS misalignments is also introduced. We compare the accuracy of covariance matrix and map ROI optical turbulence profiling using both simulated and on-sky data from CANARY, an AO demonstrator on the 4.2 m William Herschel telescope, La Palma. On-sky CANARY results are compared to contemporaneous profiles from Stereo-SCIDAR - a dedicated high-resolution optical turbulence profiler. It is shown that the covariance map ROI optimizes the accuracy of AO telemetry optical turbulence profiling. In addition, we show that the covariance map ROI reduces the fitting time for an extremely large telescope-scale system by a factor of 72. The software package we developed to collect all of the presented results is now open source.

We propose a solution to the increased computational demands of Extremely Large Telescope (ELT) scale adaptive optics (AO) real-time control with the Intel Xeon Phi Knights Landing (KNL) Many Integrated Core (MIC) Architecture. The computational demands of an AO real-time controller (RTC) scale with the fourth power of telescope diameter and so the next generation ELTs require orders of magnitude more processing power for the RTC pipeline than existing systems. The Xeon Phi contains a large number (> 64) of low power x86 CPU cores and high bandwidth memory integrated into a single socketed server CPU package. The increased parallelism and memory bandwidth are crucial to providing the performance for reconstructing wavefronts with the required precision for ELT scale AO. Here, we demonstrate that the Xeon Phi KNL is capable of performing ELT scale single conjugate AO real-time control computation at over 1.0 kHz with less than 20 {\mu}s RMS jitter. We have also shown that with a wavefront sensor camera attached the KNL can process the real-time control loop at up to 966 Hz, the maximum frame-rate of the camera, with jitter remaining below 20 {\mu}s RMS. Future studies will involve exploring the use of a cluster of Xeon Phis for the real-time control of the MCAO and MOAO regimes of AO. We find that the Xeon Phi is highly suitable for ELT AO real time control.

Astronomical adaptive optics systems are used to increase effective telescope resolution. However, they cannot be used to observe the whole sky since one or more natural guide stars of sufficient brightness must be found within the telescope field of view for the AO system to work. Even when laser guide stars are used, natural guide stars are still required to provide a constant position reference. Here, we introduce a technique to overcome this problem by using rotary unmanned aerial vehicles (UAVs) as a platform from which to produce artificial guide stars. We describe the concept, which relies on the UAV being able to measure its precise relative position. We investigate the adaptive optics performance improvements that can be achieved, which in the cases presented here can improve the Strehl ratio by a factor of at least 2 for a 8~m class telescope. We also discuss improvements to this technique, which is relevant to both astronomical and solar adaptive optics systems.

The Durham Adaptive Optics Simulation Platform (DASP) is a Monte-Carlo modelling tool used for the simulation of astronomical and solar adaptive optics systems. In recent years, this tool has been used to predict the expected performance of the forthcoming extremely large telescope adaptive optics systems, and has seen the addition of several modules with new features, including Fresnel optics propagation and extended object wavefront sensing. Here, we provide an overview of the features of DASP and the situations in which it can be used. Additionally, the user tools for configuration and control are described.

The performance of adaptive optics systems is partially dependant on the algorithms used within the real-time control system to compute wavefront slope measurements. We demonstrate use of a matched filter algorithm for the processing of elongated laser guide star (LGS) Shack-Hartmann images, using the CANARY adaptive optics instrument on the 4.2m William Herschel Telescope and the European Southern Observatory Wendelstein LGS Unit placed 40m away. This algorithm has been selected for use with the forthcoming Thirty Meter Telescope, but until now had not been demonstrated on-sky. From the results of a first observing run, we show that the use of matched filtering improves our adaptive optics system performance, with increases in on-sky H-band Strehl measured up to about a factor of 1.1 with respect to a conventional centre of gravity approach. We describe the algorithm used, and the methods that we implemented to enable on-sky demonstration.

CANARY is the multi-object adaptive optics (MOAO) on-sky pathfinder developed in the perspective of Multi-Object Spectrograph on Extremely Large Telescopes~(ELTs). In 2013, CANARY was operated on-sky at the William Herschel telescope~(WHT), using three off-axis natural guide stars~(NGS) and four off-axis Rayleigh laser guide stars~(LGS), in open-loop, with the on-axis compensated turbulence observed with a H-band imaging camera and a Truth wave-front sensor~(TS) for diagnostic purposes. Our purpose is to establish a reliable and accurate wave-front error breakdown for LGS MOAO. This will enable a comprehensive analysis of \cana on-sky results and provide tools for validating simulations of MOAO systems for ELTs. To evaluate the MOAO performance, we compared the CANARY on-sky results running in MOAO, in Single Conjugated Adaptive Optics~(SCAO) and in Ground Layer Adaptive Optics~(GLAO) modes, over a large set of data acquired in 2013. We provide a statistical study of the seeing. We also evaluated the wave-front error breakdown from both analytic computations, one based on a MOAO system modelling and the other on the measurements from the CANARY TS. We have focussed especially on the tomographic error and we detail its vertical error decomposition~(VED). We show that CANARY obtained 30.1\%, 21.4\% and 17.1\% H-band Strehl ratios in SCAO, MOAO and GLAO respectively, for median seeing conditions with 0.66" of total seeing including 0.59" at the ground. Moreover, we get 99\% of correlation over 4,500 samples, for any AO modes, between two analytic computations of residual phase variance. Based on these variances, we obtain a reasonable Strehl-ratio~(SR) estimation when compared to the measured IR image SR. We evaluate the gain in compensation for the altitude turbulence brought by MOAO when compared to GLAO.

Canary is the Multi-Object Adaptive Optics (MOAO) pathfinder for the future MOAO-assisted Integral-Field Units (IFU) proposed for Extremely Large Telescopes (ELT). The MOAO concept relies on tomographically reconstructing the turbulence using multiple measurements along different lines of sight. Tomography requires the knowledge of the statistical turbulence parameters, commonly recovered from the system telemetry using a dedicated profiling technique. For demonstration purposes with the MOAO pathfinder Canary , this identification is performed thanks to the Learn & Apply (L&A) algorithm, that consists in model- fitting the covariance matrix of WFS measurements dependent on relevant parameters: $C_n^2(h)$ profile, outer scale profile and system mis-registration. We explore an upgrade of this algorithm, the Learn 3 Steps (L3S) approach, that allows one to dissociate the identification of the altitude layers from the ground in order to mitigate the lack of convergence of the required empirical covariance matrices therefore reducing the required length of data time-series for reaching a given accuracy. For nominal observation conditions, the L3S can reach the same level of tomographic error in using five times less data frames than the L&A approach. The L3S technique has been applied over a large amount of Canary data to characterize the turbu- lence above the William Herschel Telescope (WHT). These data have been acquired the 13th, 15th, 16th, 17th and 18th September 2013 and we find 0.67"/8.9m/3.07m/s of total seeing/outer scale/wind-speed, with 0.552"/9.2m/2.89m/s below 1.5 km and 0.263"/10.3m/5.22m/s between 1.5 and 20 km. We have also de- termined the high altitude layers above 20 km, missed by the tomographic reconstruction on Canary , have a median seeing of 0.187" and have occurred 16% of observation time.

In preparation of future Multi-Object Spectrographs (MOS) whose one of the major role is to provide an extensive statistical studies of high redshifted galaxies surveyed, the demonstrator Canary has been designed to tackle technical challenges related to open-loop Adaptive-Optics (AO) control with jointed Natural Guide Star (NGS) and Laser Guide Star (LGS) tomography. We have developed a Point Spread Function (PSF)-Reconstruction algorithm dedicated to MOAO systems using system telemetry to estimate the PSF potentially anywhere in the observed field, a prerequisite to post- process AO-corrected observations in Integral Field Spectroscopy (IFS). In this paper we show how to handle off-axis data to estimate the PSF using atmospheric tomography and compare it to a classical approach that uses on-axis residual phase from a truth sensor observing a natural bright source. We have reconstructed over 450 on-sky Canary PSFs and we get bias/1-${\sigma}$ standard-deviation (std) of 1.3/4.8 on the H-band Strehl ratio (SR) with 92.3% of correlation between reconstructed and sky SR. On the Full Width at Half Maximum (FWHM), we get respectively 2.94 mas, 19.9 mas and 88.3% for the bias, std and correlation. The reference method achieves 0.4/3.5/95% on the SR and 2.71 mas/14.9 mas/92.5% on the FWHM for the bias/std/correlation.

The performance of a wide-field adaptive optics system depends on input design parameters. Here we investigate the performance of a multi-object adaptive optics system design for the European Extremely Large Telescope, using an end-to-end Monte-Carlo adaptive optics simulation tool, DASP, with relevance for proposed instruments such as MOSAIC. We consider parameters such as the number of laser guide stars, sodium layer depth, wavefront sensor pixel scale, actuator pitch and natural guide star availability. We provide potential areas where costs savings can be made, and investigate trade-offs between performance and cost, and provide solutions that would enable such an instrument to be built with currently available technology. Our key recommendations include a trade-off for laser guide star wavefront sensor pixel scale of about 0.7 arcseconds per pixel, and a field of view of at least 7 arcseconds, that EMCCD technology should be used for natural guide star wavefront sensors even if reduced frame rate is necessary, and that sky coverage can be improved by a slight reduction in natural guide star sub-aperture count without significantly affecting tomographic performance. We find that adaptive optics correction can be maintained across a wide field of view, up to 7 arcminutes in diameter. We also recommend the use of at least 4 laser guide stars, and include ground-layer and multi-object adaptive optics performance estimates.

Recent advances in adaptive optics (AO) have led to the implementation of wide field-of-view AO systems. A number of wide-field AO systems are also planned for the forthcoming Extremely Large Telescopes. Such systems have multiple wavefront sensors of different types, and usually multiple deformable mirrors (DMs). Here, we report on our experience integrating cameras and DMs with the real-time control systems of two wide-field AO systems. These are CANARY, which has been operating on-sky since 2010, and DRAGON, which is a laboratory adaptive optics real-time demonstrator instrument. We detail the issues and difficulties that arose, along with the solutions we developed. We also provide recommendations for consideration when developing future wide-field AO systems.

The spectral resolution of a dispersive astronomical spectrograph is limited by the trade-off between throughput and the width of the entrance slit. Photonic guided-wave transitions have been proposed as a route to bypass this trade-off, by enabling the efficient reformatting of incoherent seeing-limited light collected by the telescope into a linear array of single modes: a pseudo-slit which is highly multimode in one axis but diffraction-limited in the dispersion axis of the spectrograph. It is anticipated that the size of a single-object spectrograph fed with light in this manner would be essentially independent of the telescope aperture size. A further anticipated benefit is that such spectrographs would be free of `modal noise', a phenomenon that occurs in high-resolution multimode fibre-fed spectrographs due to the coherent nature of the telescope point-spread-function (PSF). We address these aspects by integrating a multicore fibre photonic lantern with an ultrafast laser inscribed three-dimensional waveguide interconnect to spatially reformat the modes within the PSF into a diffraction-limited pseudo-slit. Using the CANARY adaptive optics (AO) demonstrator on the William Herschel Telescope, and 1530 $\pm$ 80 nm stellar light, the device is found to exhibit a transmission of 47-53 % depending upon the mode of AO correction applied. We also show the advantage of using AO to couple light into such a device by sampling only the core of the CANARY PSF. This result underscores the possibility that a fully-optimised guided-wave device can be used with AO to provide efficient spectroscopy at high spectral resolution.

The performance of a wide-field adaptive optics system depends on input design parameters. Here we investigate the performance of a multi-conjugate adaptive optics system design for the European Extremely Large Telescope, using an end-to-end Monte-Carlo adaptive optics simulation tool, DASP. We consider parameters such as the number of laser guide stars, sodium layer depth, wavefront sensor pixel scale, number of deformable mirrors, mirror conjugation and actuator pitch. We provide potential areas where costs savings can be made, and investigate trade-offs between performance and cost. We conclude that a 6 laser guide star system using 3 DMs seems to be a sweet spot for performance and cost compromise.

The forthcoming Extremely Large Telescopes all require adaptive optics systems for their successful operation. The real-time control for these systems becomes computationally challenging, in part limited by the memory bandwidths required for wavefront reconstruction. We investigate new POWER8 processor technologies applied to the problem of real-time control for adaptive optics. These processors have a large memory bandwidth, and we show that they are suitable for operation of first-light ELT instrumentation, and propose some potential real-time control system designs. A CPU-based real-time control system significantly reduces complexity, improves maintainability, and leads to increased longevity for the real-time control system.

In recent years, detectors with sub-electron readout noise have been used very effectively in astronomical adaptive optics systems. Here, we compare readout noise models for the two key faint flux level detector technologies that are commonly used: EMCCD and scientific CMOS (sCMOS) detectors. We find that in almost all situations, EMCCD technology is advantageous, and that the commonly used simplified model for EMCCD readout is appropriate. We also find that the commonly used simple models for sCMOS readout noise are optimistic, and recommend that a proper treatment of the sCMOS rms readout noise probability distribution should be considered during instrument performance modelling and development.

The spectral resolution of a dispersive spectrograph is dependent on the width of the entrance slit. This means that astronomical spectrographs trade-off throughput with spectral resolving power. Recently, optical guided-wave transitions known as photonic lanterns have been proposed to circumvent this trade-off, by enabling the efficient reformatting of multimode light into a pseudo-slit which is highly multimode in one axis, but diffraction-limited in the other. Here, we demonstrate the successful reformatting of a telescope point spread function into such a slit using a three-dimensional integrated optical waveguide device, which we name the photonic dicer. Using the CANARY adaptive optics demonstrator on the William Herschel Telescope, and light centred at 1530 nm with a 160 nm FWHM, the device shows a transmission of between 10 and 20\% depending upon the type of AO correction applied. Most of the loss is due to the overfilling of the input aperture in poor and moderate seeing. Taking this into account, the photonic device itself has a transmission of 57 $\pm$ 4\%.We show how a fully-optimised device can be used with AO to provide efficient spectroscopy at high spectral resolution.

We investigate the improvements in Shack-Hartmann wavefront sensor image processing that can be realised using total variation minimisation techniques to remove noise from these images. We perform Monte-Carlo simulation to demonstrate that at certain signal-to-noise levels, sensitivity improvements of up to one astronomical magnitude can be realised. We also present on-sky measurements taken with the CANARY adaptive optics system that demonstrate an improvement in performance when this technique is employed, and show that this algorithm can be implemented in a real-time control system. We conclude that total variation minimisation can lead to improvements in sensitivity of up to one astronomical magnitude when used with adaptive optics systems.

This White Paper presents the scientific motivations for a multi-object spectrograph (MOS) on the European Extremely Large Telescope (E-ELT). The MOS case draws on all fields of contemporary astronomy, from extra-solar planets, to the study of the halo of the Milky Way and its satellites, and from resolved stellar populations in nearby galaxies out to observations of the earliest 'first-light' structures in the partially-reionised Universe. The material presented here results from thorough discussions within the community over the past four years, building on the past competitive studies to agree a common strategy toward realising a MOS capability on the E-ELT. The cases have been distilled to a set of common requirements which will be used to define the MOSAIC instrument, entailing two observational modes ('high multiplex' and 'high definition'). When combined with the unprecedented sensitivity of the E-ELT, MOSAIC will be the world's leading MOS facility. In analysing the requirements we also identify a high-multiplex MOS for the longer-term plans for the E-ELT, with an even greater multiplex (>1000 targets) to enable studies of large-scale structures in the high-redshift Universe. Following the green light for the construction of the E-ELT the MOS community, structured through the MOSAIC consortium, is eager to realise a MOS on the E-ELT as soon as possible. We argue that several of the most compelling cases for ELT science, in highly competitive areas of modern astronomy, demand such a capability. For example, MOS observations in the early stages of E-ELT operations will be essential for follow-up of sources identified by the James Webb Space Telescope (JWST). In particular, multi-object adaptive optics and accurate sky subtraction with fibres have both recently been demonstrated on sky, making fast-track development of MOSAIC feasible.

A multi-object spectrograph on the forthcoming European Extremely Large Telescope will be required to operate with good sky coverage. Many of the interesting deep cosmological fields were deliberately chosen to be free of bright foreground stars, and therefore are potentially challenging for adaptive optics (AO) systems. Here we investigate multi-object AO performance using sub-fields chosen at random from within the Great Observatories Origins Deep Survey (GOODS)-S field, which is the worst case scenario for five deep fields used extensively in studies of high-redshift galaxies. Our AO system model is based on that of the proposed MOSAIC instrument but our findings are equally applicable to plans for multi-object spectroscopy on any of the planned Extremely Large Telescopes. Potential guide stars within these sub-fields are identified and used for simulations of AO correction. We achieve ensquared energies within 75~mas of between 25-35\% depending on the sub-field, which is sufficient to probe sub-kpc scales in high-redshift galaxies. We also investigate the effect of detector readout noise on AO system performance, and consider cases where natural guide stars are used for both high-order and tip-tilt-only AO correction. We also consider how performance scales with ensquared energy box size. In summary, the expected AO performance is sufficient for a MOSAIC-like instrument, even within deep fields characterised by a lack of bright foreground stars.

Over the past 18 months we have revisited the science requirements for a multi-object spectrograph (MOS) for the European Extremely Large Telescope (E-ELT). These efforts span the full range of E-ELT science and include input from a broad cross-section of astronomers across the ESO partner countries. In this contribution we summarise the key cases relating to studies of high-redshift galaxies, galaxy evolution, and stellar populations, with a more expansive presentation of a new case relating to detection of exoplanets in stellar clusters. A general requirement is the need for two observational modes to best exploit the large (>40 sq. arcmin) patrol field of the E-ELT. The first mode ('high multiplex') requires integrated-light (or coarsely resolved) optical/near-IR spectroscopy of >100 objects simultaneously. The second ('high definition'), enabled by wide-field adaptive optics, requires spatially-resolved, near-IR of >10 objects/sub-fields. Within the context of the conceptual study for an ELT-MOS called MOSAIC, we summarise the top-level requirements from each case and introduce the next steps in the design process.

The first on-sky results obtained by CANARY, the Multi-Object Adaptive Optics (MOAO) demonstrator, are analysed. The data were recorded at the William Herschel Telescope, at the end of September 2010. We describe the command and calibrations algorithms used during the run and present the observing conditions. The processed data are MOAO-loop engaged or disengaged slope buffers, comprising the synchronised measurements of the four Natural Guide Stars (NGS) wavefront sensors running in parallel, and near Infra-Red (IR) images. We describe the method we use to establish the error budget of CANARY. We are able to evaluate the to- mographic and the open loop errors, having median values around 216 nm and 110 nm respectively. In addition, we identify an unexpected residual quasi-static field aberration term of mean value 110 nm. We present the detailed error budget analysed for three sets of data for three different asterisms. We compare the experimental budgets with the numerically simulated ones and demonstrate a good agreement. We find also a good agreement between the computed error budget from the slope buffers and the measured Strehl ratio on the IR images, ranging between 10% and 20% at 1 530 nm. These results make us confident in our ability to establish the error budget of future MOAO instruments.

We present recent results from the initial testing of an Artificial Neural Network (ANN) based tomographic reconstructor Complex Atmospheric Reconstructor based on Machine lEarNing (CARMEN) on Canary, an Adaptive Optics demonstrator operated on the 4.2m William Herschel Telescope, La Palma. The reconstructor was compared with contemporaneous data using the Learn and Apply (L&A) tomographic reconstructor. We find that the fully optimised L&A tomographic reconstructor outperforms CARMEN by approximately 5% in Strehl ratio or 15nm rms in wavefront error. We also present results for Canary in Ground Layer Adaptive Optics mode to show that the reconstructors are tomographic. The results are comparable and this small deficit is attributed to limitations in the training data used to build the ANN. Laboratory bench tests show that the ANN can out perform L&A under certain conditions, e.g. if the higher layer of a model two layer atmosphere was to change in altitude by ~300~m (equivalent to a shift of approximately one tenth of a subaperture).

Both lucky imaging techniques and adaptive optics require natural guide stars, limiting sky coverage, even when laser guide stars are used. Lucky imaging techniques become less successful on larger telescopes unless adaptive optics is used, as the fraction of images obtained with well behaved turbulence across the whole telescope pupil becomes vanishingly small. Here, we introduce a technique combining lucky imaging techniques with tomographic laser guide star adaptive optics systems on large telescopes. This technique does not require any natural guide star for the adaptive optics, and hence offers full sky-coverage adaptive optics correction. In addition, we introduce a new method for lucky image selection based on residual wavefront phase measurements from the adaptive optics wavefront sensors. We perform Monte-Carlo modelling of this technique, and demonstrate I-band Strehl ratios of up to 35% in 0.7~arcsecond mean seeing conditions with 0.5~m deformable mirror pitch and full adaptive optics sky-coverage. We show that this technique is suitable for use with lucky imaging reference stars as faint as Magnitude 18, and fainter if more advanced image selection and centring techniques are used.

Planned instruments utilising multi-object adaptive optics systems on the forthcoming extremely large telescopes require large numbers of high order deformable mirrors. These devices are a significant cost driver, particularly if specifications regarding the number of faulty actuators are stringent. Here, we investigate the effect on adaptive optics performance that such faulty actuators have, and draw conclusions about how far faulty actuator specifications (and hence cost) can be relaxed without having a significant effect on adaptive optics performance. We also provide performance estimates using a map of faulty actuators from an existing deformable mirror. We investigate the effect of faulty actuators using an end-to-end Monte Carlo adaptive optics simulation code. We find that for actuators stuck at a fixed height above the deformable mirror surface, between $1--2\%$ of actuators can be faulty before significant performance degradation occurs. For actuators that a coupled to nearest neighbours, up to about $5\%$, can be faulty before \ao performance begins to be affected.

In this paper we introduce the concept of real-time hardware-in-the-loop simulation for astronomical adaptive optics, and present the case for the requirement for such a facility. This real-time simulation, when linked with an adaptive optics real-time control system, provides an essential tool for the validation, verification and integration of the Extremely Large Telescope real-time control systems prior to commissioning at the telescope. We demonstrate that such a facility is crucial for the success of the future extremely large telescopes.

The use of laser guide stars in astronomical adaptive optics results in elongated Shack-Hartmann wavefront sensor image patterns. Image correlation techniques can be used to determine local wavefront slope by correlating each sub-aperture image with its expected elongated shape, or reference image. Here, we present a technique which allows the correlation reference images to be updated while the adaptive optics loop is closed. We show that this can be done without affecting the resulting point spread functions. On-sky demonstration is reported. We compare different techniques for obtaining the reference images, and investigate performance over a wide range of adaptive optics system parameters. We find that image correlation techniques perform better than the standard centre-of-gravity algorithm and are highly suited for use with open-loop multiple object adaptive optics systems.

Multi-object adaptive optics (MOAO) has been demonstrated by the CANARY instrument on the William Herschel Telescope. However, for proposed MOAO systems on the next generation Extremely Large Telescopes, such as EAGLE, many challenges remain. Here we investigate requirements that MOAO operation places on deformable mirrors (DMs) using a full end-to-end Monte-Carlo AO simulation code. By taking into consideration a prior global ground-layer (GL) correction, we show that actuator density for the MOAO DMs can be reduced with little performance loss. We note that this reduction is only possible with the addition of a GL DM, whose order is greater than or equal to that of the original MOAO mirrors. The addition of a GL DM of lesser order does not affect system performance (if tip/tilt star sharpening is ignored). We also quantify the maximum mechanical DM stroke requirements (3.5 $\mu$m desired) and provide tolerances for the DM alignment accuracy, both lateral (to within an eighth of a sub-aperture) and rotational (to within 0.2$^\circ$). By presenting results over a range of laser guide star asterism diameters, we ensure that these results are equally applicable for laser tomographic AO systems. We provide the opportunity for significant cost savings to be made in the implementation of MOAO systems, resulting from the lower requirement for DM actuator density.

The Durham adaptive optics real-time controller is a generic, high performance real-time control system for astronomical adaptive optics systems. It has recently had new features added as well as performance improvements, and here we give details of these, as well as ways in which optimisations can be made for specific adaptive optics systems and hardware implementations. We also present new measurements that show how this real-time control system could be used with any existing adaptive optics system, and also show that when used with modern hardware, it has high enough performance to be used with most Extremely Large Telescope adaptive optics systems.

Astronomical adaptive optics systems with open-loop deformable mirror control have recently come on-line. In these systems, the deformable mirror surface is not included in the wavefront sensor paths, and so changes made to the deformable mirror are not fed back to the wavefront sensors. This gives rise to all sorts of linearity and control issues mainly centred on one question: Has the mirror taken the shape requested? Non-linearities in wavefront measurement and in the deformable mirror shape can lead to significant deviations in mirror shape from the requested shape. Here, wavefront sensor measurements made using a brightest pixel selection method are discussed along with the implications that this has for open-loop AO systems. Discussion includes elongated laser guide star spots and also computational efficiency.

The Durham adaptive optics real-time controller was initially a proof of concept design for a generic adaptive optics control system. It has since been developed into a modern and powerful CPU based real-time control system, capable of using hardware acceleration (including FPGAs and GPUs), based primarily around commercial off the shelf hardware. It is powerful enough to be used as the real-time controller for all currently planned 8~m class telescope adaptive optics systems. Here we give details of this controller and the concepts behind it, and report on performance including latency and jitter, which is less than 10~$\mu$s for small adaptive optics systems.

The EAGLE instrument for the E-ELT is a multi-IFU spectrograph, that uses a MOAO system for wavefront correction of interesting lines of sight. We present a Monte-Carlo AO simulation package that has been used to model the performace of EAGLE, and provide results, including comparisons with an analytical code. These results include an investigation of the performance of compressed reconstructor representations that have the potential to significantly reduce the complexity of a real-time control system when implemented.

Adaptive optics systems are essential on all large telescopes where image quality is important. These are complex systems with many design parameters requiring optimisation before good performance can be achieved. The simulation of adaptive optics systems is therefore necessary to categorise the expected performance. This paper describes an adaptive optics simulation platform, developed at Durham University, which can be used to simulate adaptive optics systems on the largest proposed future extremely large telescopes (ELTs) as well as current systems. This platform is modular, object oriented and has the benefit of hardware application acceleration which can be used to improve the simulation performance, essential for ensuring that the run time of a given simulation is acceptable. The simulation platform described here can be highly parallelised using parallelisation techniques suited for adaptive optics simulation, whilst still offering the user complete control while the simulation is running. Results from the simulation of a ground layer adaptive optics system are provided as an example to demonstrate the flexibility of this simulation platform.

A technique used to accelerate an adaptive optics simulation platform using reconfigurable logic is described. The performance of parts of this simulation have been improved by up to 600 times (reducing computation times by this factor) by implementing algorithms within hardware and enables adaptive optics simulations to be carried out in a reasonable timescale. This demonstrates that it is possible to use reconfigurable logic to accelerate computational codes by very large factors when compared with conventional software approaches, and this has relevance for many computationally intensive applications. The use of reconfigurable logic for high performance computing is currently in its infancy and has never before been applied to this field.

Numerical Simulation is an essential part of the design and optimisation of astronomical adaptive optics systems. Simulations of adaptive optics are computationally expensive and the problem scales rapidly with telescope aperture size, as the required spatial order of the correcting system increases. Practical realistic simulations of AO systems for extremely large telescopes are beyond the capabilities of all but the largest of modern parallel supercomputers. Here we describe a more cost effective approach through the use of hardware acceleration using field programmable gate arrays. By transferring key parts of the simulation into programmable logic, large increases in computational bandwidth can be expected. We show that the calculation of wavefront sensor image centroids can be accelerated by a factor of four by transferring the algorithm into hardware. Implementing more demanding parts of the adaptive optics simulation in hardware will lead to much greater performance improvements, of up to 1000 times.

Group delay fringe tracking using spectrally-dispersed fringes is suitable for stabilising the optical path difference in ground-based astronomical optical interferometers in low light situations. We discuss the performance of group delay tracking algorithms when the effects of atmospheric dispersion, high-frequency atmospheric temporal phase variations, non-ideal path modulation, non-ideal spectral sampling, and the detection artifacts introduced by electron-multiplying CCDs (EMCCDs) are taken into account, and we present ways in which the tracking capability can be optimised in the presence of these effects.

Recently, low light level charge coupled devices (L3CCDs) capable of on-chip gain have been developed, leading to sub-electron effective readout noise, allowing for the detection of single photon events. Optical interferometry usually requires the detection of faint signals at high speed and so L3CCDs are an obvious choice for these applications. Here we analyse the effect that using an L3CCD has on visibility parameter estimation (amplitude and triple product phase), including situations where the L3CCD raw output is processed in an attempt to reduce the effect of stochastic multiplication noise introduced by the on-chip gain process. We establish that under most conditions, fringe parameters are estimated accurately, whilst at low light levels, a bias correction which we determine here, may need to be applied to the estimate of fringe visibility amplitude. These results show that L3CCDs are potentially excellent detectors for astronomical interferometry at optical wavelengths.

Low light level charge coupled devices (L3CCDs) have recently been developed, incorporating on-chip gain. They may be operated to give an effective readout noise much less than one electron by implementing an on-chip gain process allowing the detection of individual photons. However, the gain mechanism is stochastic and so introduces significant extra noise into the system. In this paper we examine how best to process the output signal from an L3CCD so as to minimize the contribution of stochastic noise, while still maintaining photometric accuracy. We achieve this by optimising a transfer function which translates the digitised output signal levels from the L3CCD into a value approximating the photon input as closely as possible by applying thresholding techniques. We identify several thresholding strategies and quantify their impact on photon counting accuracy and effective signal-to-noise. We find that it is possible to eliminate the noise introduced by the gain process at the lowest light levels. Reduced improvements are achieved as the light level increases up to about twenty photons per pixel and above this there is negligible improvement. Operating L3CCDs at very high speeds will keep the photon flux low, giving the best improvements in signal-to-noise ratio.