Accurate wavelength calibration is an important factor for any measurement with high resolution spectrographs. Stellar spectrum comprises of discrete absorption or emission lines whose position is precisely determined by calibrating the spectrograph using known reference lines generated from laboratory sources. For the spectrograph to measure small variations in Doppler shift, the wavelength calibration must be sufficiently stable during observation time. Instrument instability, mainly due to environmental factors like temperature and pressure variations, limitations of traditional calibration methods, for example Th-Ar lamps, are the main challenges which high precision spectroscopy. Through proper environmental control, by maintaining pressure at few mbar and temperature fluctuations within $\pm$0.05$^{\circ}$C, Fabry P\'erot etalon (FP) can yield a velocity precision of 1-10 m/s, when used for wavelength calibration. We have developed a passively stabilized FP based wavelength calibrator for Hanle Echelle Spectrograph (HESP) installed on Himalayan Chandra Telescope (HCT) at Indian Astronomical Observatory (IAO), Hanle, India. The etalon has been characterized using Fourier Transform Spectrograph (FTS) and initial test runs have been performed with HESP. In this paper we present the design and construction of the instrument along with preliminary test results obtained from HESP.

We developed a tip-tilt system to compensate the turbulence induced image motion for 1.3 m telescope at Vainu Bappu Observatory, Kavalur. The instrument is designed to operate at visible wavelength band (480-700 nm) with a field of view $1^{\prime}\times1^{\prime}$. The tilt corrected images have shown up to $\approx$ 57% improvement in image resolution and a corresponding peak intensity increase by a factor of $\approx$ 2.8. A closed-loop correction bandwidth of $\approx$ 26 Hz has been achieved with on-sky tests and the root mean square motion of the star image has been reduced by a factor of $\sim$ 14. These results are consistent with theoretical and numerical predictions of wave-front aberrations caused by atmospheric turbulence and image quality improvement expected from a real-time control system. In this paper, we present the details of the instrument design, laboratory calibration studies and quantify its performance on the telescope.

HISPEC (High-resolution Infrared Spectrograph for Exoplanet Characterization) is a proposed diffraction-limited spectrograph for the W.M. Keck Observatory, and a pathfinder for the MODHIS facility project (Multi-Object Diffraction-limited High-resolution Infrared Spectrograph) on the Thirty Meter Telescope. HISPEC/MODHIS builds on diffraction-limited spectrograph designs which rely on adaptively corrected single-mode fiber feeds. Seeing-limited high-resolution spectrographs, by virtue of the conservation of beam etendue, grow in volume following a D^3 power law (D is the telescope diameter), and are subject to daunting challenges associated with their large size. Diffraction-limited spectrographs fed by single mode fibers are decoupled from the telescope input, and are orders of magnitude more compact and have intrinsically stable line spread functions. Their efficiency is directly proportional to the performance of the adaptive optics (AO) system. AO technologies have matured rapidly over the past two decades and are baselined for future extremely large telescopes. HISPEC/MODHIS will take R>100,000 spectra of a few objects in a 10" field-of-view sampled at the diffraction limit (~10-50 mas), simultaneously from 0.95 to 2.4 microns (y-K). The scientific scope ranges from exoplanet infrared precision radial velocities, spectroscopy of transiting, close-in, and directly imaged exoplanets (atmospheric composition and dynamics, RM effect, spin measurements, Doppler imaging), brown dwarf characterization, stellar physics/chemistry, proto-planetary disk kinematics/composition, Solar system, extragalactic science, and cosmology. HISPEC/MODHIS features a compact, cost-effective design optimized to fully exploit the existing Keck-AO and future TMT-NFIRAOS infrastructures and boost the scientific reach of Keck Observatory and TMT soon after first light.

The Echelle spectrograph operating at Vainu Bappu Telescope (VBT), India, is a general purpose instrument used for many high-resolution spectroscopic observations. A concerted effort is being made to expand the scientific capability of the instrument in emerging areas of observational astronomy. The present study is aimed at evaluating the feasibility of the spectrograph to carry out precision Radial Velocity (RV) measurements. In the current design, major factors limiting the RV precision of the spectrograph arise from the movable grating and slit; optical aberrations; positional uncertainty associated with optomechanical mounts and environmental and thermal instabilities in the spectrograph room. RV instabilities due to temperature and pressure variations in the environment are estimated to vary around 120 $ \textrm{ms}^{-1} $ and 400 $ \textrm{ms}^{-1} $ respectively. The positional uncertainty of the grating in the spectrograph could induce a spectral shift $\sim1.4\,\textrm{kms}^{-1} $ across the Echelle orders. A Zemax model is used to overcome the uncertainty in the zero-positioning and lack of repeatability of the moving components. We propose to obtain the ThAr lamp observations and using the Zemax model as the reference, predict the drifts in the positions of the optical components. The perturbations of the optical components from the nominal position are corrected at the beginning of the observational run. After a good match is obtained between the model and the observations, we propose to use a Zemax model to improve the wavelength calibration solution. We could match the observations and model within $\pm$~1 pixels accuracy after the model parameters were perturbed in a real-time setup of the spectrograph. In this paper, we present the estimation of the perturbations of optical components and the effect on the RV obtained.

The Echelle spectrograph operating at Vainu Bappu Telescope (VBT) is a general purpose instrument designed for high resolution spectroscopy. It is being considered for precision Doppler measurements without altering the existing design and basic usage. However, the design level limitations and environmental perturbations are a major source of instability and systematic errors. As a result, a small Doppler signal in the stellar spectra is completely swamped by the large and uncontrolled instrumental drift. In this paper, we discuss some of the remedial measures we took to improve the radial velocity performance of the spectrograph. We show that a new auto-guider assembly has greatly reduced the mechanical jitter of the star image at the fibre input, making the illumination of the spectrograph slit at the other end stable. We have also installed an iodine absorption cell to track and eliminate the instrumental drifts to facilitate precision radial velocity observations. Furthermore, we have developed a generic algorithm that uses iodine exposures to extract the stellar radial velocities without the need for the complex forward modeling. Our algorithm is not accurate to the level of traditional iodine technique. However it is convenient to use on a low-cost general-purpose spectrograph targeting a moderate Radial Velocity (RV) precision at a few 10-100~$\textrm{ms}^{-1}$ level. Finally, we have demonstrated the usefulness of our approach by measuring the RV signal of a well known short-period, planet-hosting star.

We report the atmospheric turbulence parameters namely, atmospheric seeing, the tilt-anisoplanatic angle ($\theta_0$) and the coherence time ($\tau_0$), measured under various sky conditions, at Vainu Bappu Observatory in Kavalur. Bursts of short exposure images of selected stars were recorded with a high-speed, frame-transfer CCD mounted on the Cassegrain focus of a newly commissioned 1.3 m telescope. The estimated median seeing is $ \approx 1.85^{\prime\prime} $ at wavelength of $\sim 600$ nm, the image motion correlation between different pairs of stars is $\sim 44\%$ for $\theta_0 \approx 36^{\prime\prime}$ and mean $\tau_0$ is $\approx 2.4$ ms. This work was motivated by the design considerations and expected the performance of an adaptive optics system that is currently being planned for the telescope.

Correlations between the occurrence rate of exoplanets and their host star properties provide important clues about the planet formation processes. We studied the dependence of the observed properties of exoplanets (radius, mass, and orbital period) as a function of their host star metallicity. We analyzed the planetary radii and orbital periods of over 2800 $Kepler$ candidates from the latest $Kepler$ data release DR25 (Q1-Q17) with revised planetary radii based on $Gaia$~DR2 as a function of host star metallicity (from the Q1-Q17 (DR25) stellar and planet catalog). With a much larger sample and improved radius measurements, we are able to reconfirm previous results in the literature. We show that the average metallicity of the host star increases as the radius of the planet increases. We demonstrate this by first calculating the average host star metallicity for different radius bins and then supplementing these results by calculating the occurrence rate as a function of planetary radius and host star metallicity. We find a similar trend between host star metallicity and planet mass: the average host star metallicity increases with increasing planet mass. This trend, however, reverses for masses $> 4.0\, M_\mathrm{J}$: host star metallicity drops with increasing planetary mass. We further examined the correlation between the host star metallicity and the orbital period of the planet. We find that for planets with orbital periods less than 10 days, the average metallicity of the host star is higher than that for planets with periods greater than 10 days.

We report the observations of the solar chromosphere from a newly commissioned solar telescope at the incursion site near Pangong Tso lake in Merak (Leh/Ladakh). This new H$_{\alpha}$ telescope at the Merak site is identical to the Kodaikanal H$_{\alpha}$ telescope. The telescope is installed in the month of August, 2017 at the Merak site. A 20-cm doublet lens with additional re-imaging optics makes the telescope. A Lyot filter with 0.5~\AA~passband isolates the Balmer line of the hydrogen spectra to make the observations of the solar chromosphere. The observations made in H$_{\alpha}$ wavelength delineates the magnetic field directions at the sunspot and the quiet regions. A CCD detector records the images of the chromosphere with a pixel resolution of 0.27$^{\prime\prime}$ and covers 9.2$^{\prime}$ field-of-view. This telescope has a good guiding system that keeps the FOV in the intended position. We report the development of control software for tuning the filter unit, control detector system, observations, and calibration of the data to make it useful for the scientific community. Some preliminary results obtained from the Merak H$_{\alpha}$ telescope are also presented. This high altitude facility is a timely addition to regularly available H$_{\alpha}$ images around the globe.

Ground layer turbulence is a very important site characterization parameter used to assess the quality of an astronomical site. The Lunar Scintillometer is a simple and effective site-testing device for measuring the ground layer turbulence. It consists of a linear array of photodiodes which are sensitive to the slight variations in the moon's brightness due to scintillation by the lower layers of the Earth's atmosphere. The covariance of intensity values between the non-redundant photodiode baselines can be used to measure the turbulence profile from the ground up to a height determined by the furthest pair of detectors. The six channel lunar scintillometer that has been developed at the Indian Institute of Astrophysics is based closely on an instrument built by the team led by Andrei Tokovinin of Cerro Tololo Inter-American Observatory (CTIO), Chile. We have fabricated the instrument based on the existing electronic design, and have worked on the noise analysis, an EMI (Electromagnetic Induction) resistant PCB design and the software pipeline for analyzing the data from the same. The results from the instrument's multi-year campaign at Mount Saraswati, Hanle is also presented.

A fiber-fed Echelle spectrograph at 2.3 m Vainu Bappu Telescope (VBT), Kavalur, has been in operation since 2005. Owing to various technological advancements in precision spectroscopy in recent years, several research avenues have been opened in observational astronomy. These developments have created a demand to improve the Doppler precision of our spectrograph. Currently, the stability of the instrument is compromised by the temperature and pressure fluctuations inside the Echelle room. Further, a better wavelength calibration approach is needed to carefully track and disentangle the instrumental effects from stellar spectra. While planning a possible upgrade with an Iodine absorption gas cell, we measured the raw stability of the spectrograph using a series of calibration frames taken with the ThAr gas discharge lamp. The time series data were analysed with cross-correlation method and the shift in ThAr emission lines was accurately measured across different Echelle orders. In this paper, we present our stability analysis methodology and results for the Kavalur spectrograph. We also identify possible sources of error and discuss our strategy to mitigate them.

Using multi-wavelength observation from SDO and STEREO, we investigated the mechanism of two successive eruptions (F1 & F2) of a filament in active region NOAA 11444 on 27 march, 2012. The filament was inverse `J' shaped and lying along a quasi-circular polarity inversion line (PIL). The first part of the filament (F1) erupted at ~2:30UT on 27 March 2012, the second part of the filament (F2) erupted at around 4:20 UT on the same day. A precursor/pre-flare brightening was observed below filament's main axis about 30 min prior to F1. The brightening was followed by a jet-like ejection below filament, which triggered the eruption. Before the eruption of F2, the filament seems to be trapped within the overlying arcade loops almost for $\sim$1.5~hr before its successful eruption. Interestingly, we observed simultaneously contraction (~12km/s) and expansion (~20km/s) of arcade loops in the active region before F2. HMI magnetograms show the converging motion of the opposite polarities resulting in flux cancellation near PIL. We suggest that flux cancellation at PIL resulted jet-like ejection below filament's main axis, which triggered the eruption F1 similar to tether-cutting process. The eruption F2 was triggered by removal of the overlying arcade loops via reconnection process. Both filament eruptions produced high speed (~1000km/s) CMEs.

We propose a dual cavity Fabry-Perot interferometer as a wavelength calibrator and a stability tracking device for astronomical spectrograph. The FPI consists of two adjoining cavities engraved on a low expansion monoblock spacer. A low-finesse astro-cavity is intended for generating a uniform grid of reference lines to calibrate the spectrograph and a high-finesse lock-cavity is meant for tracking the stability of the reference lines using optical frequency standards. The differential length changes in two cavities due to temperature and vibration perturbations are quantitatively analyzed using finite element method. An optimized mounting geometry with fractional length changes $\Delta L/L \approx 1.5\times 10^{-12}$ is suggested. We also identify conditions necessary to suppress relative length variations between two cavities well below 10$^{-10}$~m, thus facilitating accurate dimension tracking and generation of stable reference spectra for Doppler measurement at 10 cms$^{-1}$ level.

We have recently developed a narrow band imager (NBI) using an air gap based Fabry-P\'erot (FP) interferometer at the Indian Institute of Astrophysics, Bangalore. Narrow band imaging is achieved by using an FP interferometer working in combination with an order sorting pre-filter. The NBI can be tuned to a different wavelength position on the line profile by changing the plate separation of the FP. The interferometer has a 50 mm clear aperture with a bandpass of $\sim$247.8 m\AA and a free spectral range of $\sim$5.3\AA at $\lambda$ = 656.3 nm. The developed NBI is used to observe the solar filament in the H$\alpha$ wavelength. The instrument is being used to image the Sun at chromospheric height and it is also able to scan the H$\alpha$ spectral line profile at different wavelength positions. We have also made Doppler velocity maps at chromospheric height by taking the blue and red wing images at $\pm$176 m\AA wavelength positions separately away from the line center of the spectral line. In this paper, we present a description of the NBI including lab test results of individual components and some initial observations carried out with this instrument.

Solar filaments/prominences exhibit rotational motion during different phases of their evolution from their formation to eruption. We have observed the rotational/vortical motion in the photosphere near the ends of ten filaments during their initial phase of eruption, at the onset of the fast rise phase. All the filaments were associated with active regions. The photospheric vortical motions we observed lasted for 4--20 minutes. In the vicinity of the conjugate ends of the filament the direction of rotation was opposite, except for two cases, where rotational motion was observed at only one end point. The sudden onset of a large photospheric vortex motion could have played a role in destabilizing the filament by transporting axial flux into the activated filament thereby increasing the outward magnetic pressure in it. The outward magnetic pressure may have pushed the filament/flux rope to the height where the torus instability criterion was satisfied, and hence it could have caused the filament instability and eruption.

State-of-the-art Doppler experiments require wavelength calibration with precision at the cm/s level. A low-finesse Fabry-Perot interferometer (FPI) can provide a wavelength comb with a very large bandwidth as required for astronomical experiments, but unavoidable spectral drifts are difficult to control. Instead of actively controlling the FPI cavity, we propose to passively stabilize the interferometer and track the time-dependent cavity length drift externally. A dual-finesse cavity allows drift tracking during observation. The drift of the cavity length is monitored in the high-finesse range relative to an external standard: a single narrow transmission peak is locked to an external cavity diode laser and compared to an atomic frequency. Following standard locking schemes, tracking at sub-mm/s precision can be achieved. This is several orders of magnitude better than currently planned high-precision Doppler experiments. It allows freedom for relaxed designs rendering this approach particularly interesting for upcoming Doppler experiments. We also show that the large number of interference modes used in an FPI allows us to unambiguously identify the interference mode of each FPI transmission peak defining its absolute wavelength solution. The accuracy reached in each resonance with the laser concept is then defined by the cavity length that is determined from the one locked peak and by the group velocity dispersion. The latter can vary by several 100m/s over the relevant frequency range and severely limits the accuracy of individual peak locations. A potential way to determine the absolute peak positions is to externally measure the frequency of each individual peak with a laser frequency comb (LFC). Thus, the concept of laser-locked FPIs may be useful for applying the absolute accuracy of an LFC to astronomical spectrographs without the need for an LFC at the observatory.

The active region magnetic field surrounding the filament plays an important role in filament formation, their evolution and disruption. We investigated a filament eruption that occurred in southern hemisphere of the Sun on July 08, 2011 using AIA and HMI data. The filament was located in a region close to the active region NOAA 11247 with its West-most footpoint anchored in the negative polarity plage region and the East-most in the positive polarity plage region. During observations, the magnetic flux was emerging in the active region and also in the plage regions. The flux emergence was stopped in West-most footpoint of the plage region about an hour before the filament eruption. A converging motion was also observed for many hours in the Western footpoint of the filament. The filament had left-handed twist and the net injected magnetic helicity was positive in both footpoints. Both sign of magnetic helicity were observed in the Western footpoint of the filament where the eruption has initiated. Further, an anti-clockwise rotational motion was observed in both the footpoints just after the onset of filament eruption which lasted for 6 min during the eruption process. The emerging flux, converging motion and injection of opposite magnetic helicity could be responsible for destabilizing of the Western footpoint of the filament leading to eruption. The torque imbalance between the expanded portion of the flux tube and the photosphere may have caused the rotation in the footpoint region which changed the trend in the injected magnetic helicity after the filament eruption.

In this paper, an opto-thermal analysis of a moderately heated lightweighted solar telescope mirror is carried out using 3D finite element analysis (FEA). A physically realistic heat transfer model is developed to account for the radiative heating and energy exchange of the mirror with surroundings. The numerical simulations show the non-uniform temperature distribution and associated thermo-elastic distortions of the mirror blank clearly mimicking the underlying discrete geometry of the lightweighted substrate. The computed mechanical deformation data is analyzed with surface polynomials and the optical quality of the mirror is evaluated with the help of a ray-tracing software. The thermal print-through distortions are further shown to contribute to optical figure changes and mid-spatial frequency errors of the mirror surface. A comparative study presented for three commonly used substrate materials, namely, Zerodur, Pyrex and Silicon Carbide (SiC) is relevant to vast area of large optics requirements in ground and space applications.

We present a detailed thermal and structural analysis of a 2m class solar telescope mirror which is subjected to a varying heat load at an observatory site. A 3-dimensional heat transfer model of the mirror takes into account the heating caused by a smooth and gradual increase of the solar flux during the day-time observations and cooling resulting from the exponentially decaying ambient temperature at night. The thermal and structural response of two competing materials for optical telescopes, namely Silicon Carbide -best known for excellent heat conductivity and Zerodur -preferred for its extremely low coefficient of thermal expansion, is investigated in detail. The insight gained from these simulations will provide a valuable input for devising an efficient and stable thermal control system for the primary mirror.

The phase characteristics of reflecting and transmitting type twisted nematic liquid crystal based Spatial Light Modulators (SLMs) were measured using interferometry. Device parameters like contrast, brightness, input and output polarizer angles have been optimized and SLM phase nonlinearity was reduced by higher order polynomial interpolation. Higher order aberration production ability of SLMs was tested by measuring the shift in the spots of a Shack Hartmann Sensor.

We present a liquid crystal method of correcting the phase of an aberrated wavefront using a spatial light modulator. A simple and efficient lab model has been demonstrated for wavefront correction. The crux of a wavefront correcting system in an adaptive optics system lies in the speed and the image quality that can be achieved. The speeds and the accuracy of wavefront representation using Zernike polynomials have been presented using a very fast method of computation.