This paper reports on the modal noise characterisation of a hybrid reformatter. The device consists of a multicore-fibre photonic lantern and an ultrafast laser-inscribed slit reformatter. It operates around 1550 nm and supports 92 modes. Photonic lanterns transform a multimode signal into an array of single-mode signals, and thus combine the high coupling efficiency of multimode fibres with the diffraction-limited performance of single-mode fibres. This paper presents experimental measurements of the device point spread function properties under different coupling conditions, and its throughput behaviour at high spectral resolution. The device demonstrates excellent scrambling but its point spread function is not completely stable. Mode field diameter and mode barycentre position at the device output vary as the multicore-fibre is agitated due to the fabrication imperfections.

The spectral resolution of a dispersive astronomical spectrograph is limited by the trade-off between throughput and the width of the entrance slit. Photonic guided-wave transitions have been proposed as a route to bypass this trade-off, by enabling the efficient reformatting of incoherent seeing-limited light collected by the telescope into a linear array of single modes: a pseudo-slit which is highly multimode in one axis but diffraction-limited in the dispersion axis of the spectrograph. It is anticipated that the size of a single-object spectrograph fed with light in this manner would be essentially independent of the telescope aperture size. A further anticipated benefit is that such spectrographs would be free of `modal noise', a phenomenon that occurs in high-resolution multimode fibre-fed spectrographs due to the coherent nature of the telescope point-spread-function (PSF). We address these aspects by integrating a multicore fibre photonic lantern with an ultrafast laser inscribed three-dimensional waveguide interconnect to spatially reformat the modes within the PSF into a diffraction-limited pseudo-slit. Using the CANARY adaptive optics (AO) demonstrator on the William Herschel Telescope, and 1530 $\pm$ 80 nm stellar light, the device is found to exhibit a transmission of 47-53 % depending upon the mode of AO correction applied. We also show the advantage of using AO to couple light into such a device by sampling only the core of the CANARY PSF. This result underscores the possibility that a fully-optimised guided-wave device can be used with AO to provide efficient spectroscopy at high spectral resolution.

The spectral resolution of a dispersive spectrograph is dependent on the width of the entrance slit. This means that astronomical spectrographs trade-off throughput with spectral resolving power. Recently, optical guided-wave transitions known as photonic lanterns have been proposed to circumvent this trade-off, by enabling the efficient reformatting of multimode light into a pseudo-slit which is highly multimode in one axis, but diffraction-limited in the other. Here, we demonstrate the successful reformatting of a telescope point spread function into such a slit using a three-dimensional integrated optical waveguide device, which we name the photonic dicer. Using the CANARY adaptive optics demonstrator on the William Herschel Telescope, and light centred at 1530 nm with a 160 nm FWHM, the device shows a transmission of between 10 and 20\% depending upon the type of AO correction applied. Most of the loss is due to the overfilling of the input aperture in poor and moderate seeing. Taking this into account, the photonic device itself has a transmission of 57 $\pm$ 4\%.We show how a fully-optimised device can be used with AO to provide efficient spectroscopy at high spectral resolution.

The performance of highly-multiplexed spectrographs is limited by focal degradation (FRD) in the optical fibres. It has already been shown that this is caused mainly by processes concentrated around the mounting points at the ends of the fibres. We use the thickness of rings produced in the farfield when a fibre is illuminated by a collimated beam, to estimate the size of the region where the FRD is generated. This requires the development of a new model, using features of existing ray-tracing and wave-based models, which fits existing data very well. The results suggest that the amount of FRD is primarily determined by the length of fibre bonded into the supporting ferrule. We point out the implications for the production of future fibre systems.

One of the problems of producing instruments for Extremely Large Telescopes is that their size (and hence cost) scales rapidly with telescope aperture. To try to break this relation alternative new technologies have been proposed, such as the use of the Integrated Photonic Spectrograph (IPS). Due to their diffraction-limited nature the IPS is claimed to defeat the harsh scaling law applying to conventional instruments. In contrast to photonic applications, devices for astronomy are not usually used at the diffraction limit. Therefore to retain throughput and spatial information, the IPS requires a photonic lantern (PL) to decompose the input multimode light into single modes. This is then fed into either numerous Arrayed Waveguide Gratings (AWGs) or a conventional spectrograph. We investigate the potential advantage of using an IPS instead of conventional monolithic optics for a variety of capabilities represented by existing instruments and others planned for Extremely Large Telescopes. We show that a full IPS instrument is equivalent to an image-slicer. However, the requirement to decompose the input light into individual modes imposes a redundancy in terms of the numbers of components and detector pixels in many cases which acts to cancel out the advantage of the small size of the photonic components. However, there are specific applications where an IPS gives a potential advantage which we describe. Furthermore, the IPS approach has the potential advantage of minimising or eliminating bulk optics. We show that AWGs fed with multiple single-mode inputs from a PL require relatively bulky auxiliary optics and a 2-D detector array. A more attractive option is to combine the outputs of many AWGs so that a 1-D detector can be used to greatly reduce the number of detector pixels required and provide efficient adaptation to the curved output focal surface.

One of the well-known problems of producing instruments for Extremely Large Telescopes is that their size (and hence cost) scales rapidly with telescope aperture. To try to break this relation alternative new technologies have been proposed, such as the use of the Integrated Photonic Spectrograph (IPS). Due to their diffraction limited nature the IPS is claimed to defeat the harsh scaling law applying to conventional instruments. The problem with astronomical applications is that unlike conventional photonics, they are not usually fed by diffraction limited sources. This means in order to retain throughput and spatial information the IPS will require multiple Arrayed Waveguide Gratings (AWGs) and a photonic lantern. We investigate the implications of these extra components on the size of the instrument. We also investigate the potential size advantage of using an IPS as opposed to conventional monolithic optics. To do this, we have constructed toy models of IPS and conventional image sliced spectrographs to calculate the relative instrument sizes and their requirements in terms of numbers of detector pixels. Using these models we can quantify the relative size/cost advantage for different types of instrument, by varying different parameters e.g. multiplex gain and spectral resolution. This is accompanied by an assessment of the uncertainties in these predictions, which may prove crucial for the planning of future instrumentation for highly-multiplexed spectroscopy.

Optical fibres are essential for many types of highly-multiplexed and precision spectroscopy. The success of the new generation of multifibre instruments under construction to investigate fundamental problems in cosmology, such as the nature of dark energy, requires accurate modellisation of the fibre system to achieve their signal-to-noise goals. Despite their simple construction, fibres exhibit unexpected behaviour including non-conservation of Etendue (Focal Ratio Degradation; FRD) and modal noise. Furthermore, new fibre geometries (non-circular or tapered) have become available to improve the scrambling properties that, together with modal noise, limit the achievable SNR in precision spectroscopy. These issues have often been addressed by extensive tests on candidate fibres and their terminations but these are difficult and time-consuming. Modelling by ray-tracing and wave analysis is possible with commercial software packages but these do not address the more complex features, in particular FRD. We use a phase-tracking ray-tracing method to provide a practical description of FRD derived from our previous experimental work on circular fibres and apply it to non-standard fibres. This allows the relationship between scrambling and FRD to be quantified for the first time. We find that scrambling primarily affects the shape of the near-field pattern but has negligible effect on the barycentre. FRD helps to homogenise the nearfield pattern but does not make it completely uniform. Fibres with polygonal cross-section improve scrambling without amplifying the FRD. Elliptical fibres, in conjunction with tapering, may offer an efficient means of image slicing to improve the product of resolving power and throughput but the result is sensitive to the details of illumination.

Using ultrafast laser inscription, we report the fabrication of a prototype three-dimensional 121-waveguide fan-out device capable of reformatting the output of a 120 core multicore fiber (MCF) into a one-dimensional linear array. When used in conjunction with an actual MCF, we demonstrate that the reformatting function using this prototype would result in an overall throughput loss of approximately 7.0 dB. However, if perfect coupling from the MCF into the fan-out could be achieved, the reformatting function would result in an overall loss of only approximately 1.7 dB. With adequate development, similar devices could efficiently reformat the output of so-called "photonic lanterns" fabricated using highly multicore fibers.

Fibre modal noise occurs in high spectral resolution, high signal-to-noise applications. It imposes fundamental limits on the photometric accuracy of state-of-the-art fibre-spectrograph systems. In order to maximize the performance of current and future instruments it is therefore essential to predict fibre modal noise. To attain a predictive model we are using a dual approach, bringing theoretical assumptions in line with the experimental data obtained using a test-bench spectrograph. We show that the task of noise prediction can be reduced to determining the visibility of the modal pattern which can be measured at the detector plane. Subsequently, the visibility-dependence of essential parameters is presented. This work will soon provide a basis for prediction of modal noise limitations in fibre-coupled spectrograph designs.

We investigate the dependence on length of optical fibres used in astronomy, especially the focal ratio degradation (FRD) which places constraints on the performance of fibre-fed spectrographs used for multiplexed spectroscopy. To this end we present a modified version of the FRD model proposed by Carrasco and Parry \cite{Carrasco1994} to quantify the the number of scattering defects within an optical fibre using a single parameter. The model predicts many trends which are seen experimentally, for example, a decrease in FRD as core diameter increases, and also as wavelength increases. However the model also predicts a strong dependence on FRD with length that is not seen experimentally. By adapting the single fibre model to include a second fibre, we can quantify the amount of FRD due to stress caused by the method of termination. By fitting the model to experimental data we find that polishing the fibre causes more stress to be induced in the end of the fibre compared to a simple cleave technique. We estimate that the number of scattering defects caused by polishing is approximately double that produced by cleaving. By placing limits on the end-effect, the model can be used to estimate the residual-length dependence in very long fibres, such as those required for Extremely Large Telescopes (ELTs), without having to carry out costly experiments. We also use our data to compare different methods of fibre termination.

A photonic spectrograph can be much smaller than a conventional spectrograph with the same resolving power. Individual devices can be integrated with optical fibres to improve the multiplex gain in astronomical spectroscopy. Although experimental devices have been tested, the parameter space where integrated photonic spectrographs give a significant advantage over traditional methods has not been defined. This paper gives an overview of the theory with verification by direct simulation using Fresnel propagation and quantifies the benefit for representative spectroscopic capabilities. We thereby confirm the advantage of photonic spectrographs, especially to the next generation of Extremely Large Telescopes, and therefore conclude that these devices may be important for the future development of astronomical instrumentation.

One of the problems of producing spectrographs for Extremely Large Telescopes (ELTs) is that the beam size is required to scale with telescope aperture if all other parameters are held constant, leading to enormous size and implied cost. This is a particular problem for image sizes much larger than the diffraction limit, as is likely to be the case if Adaptive Optics systems are not initially able to deliver highly corrected images over the full field of the instrument or if signal/noise considerations require large spatial samples. In this case, there is a potential advantage in image slicing to reduce the effective slitwidth and hence the beam size. However, this implies larger detectors and oversizing of the optics which may cancel out the advantage. By the means of a toy model of a spectrograph whose dimensions are calibrated using existing instruments, the size and relative cost of spectrographs for ELTs have been estimated. Using a range of scaling laws derived from the reference instruments, it is possible to estimate the uncertainties in the predictions and to explore the consequences of different design strategies. The model predicts major cost savings (2 - 100x) by slicing with factors of 5-20 depending on the type of spectrograph. The predictions suggest that it is better to accommodate the multiplicity of slices within a single spectrograph rather than distribute them among smaller, cheaper replicas in a parallel architecture, but the replication option provides an attractive upgrade path to integral field spectroscopy (IFS) as the input image quality is improved... [Full abstract in text]

The fields of view of Extremely Large Telescopes will contain vast numbers of spatial sampling elements (spaxels) as their Adaptive Optics systems approach the diffraction limit over wide fields. Since this will exceed the detection capabilities of any realistic instrument, the field must be dilutely sampled to extract spectroscopic data from selected regions of interest. The scientific return will be maximised if the sampling pattern provides an adaptable combination of separated independent spaxels and larger contiguous sub-fields, seamlessly combining integral-field and multiple-object spectroscopy. We illustrate the utility of this Diverse Field Spectroscopy (DFS) to cosmological studies of galaxy assembly. We show how to implement DFS with an instrument concept: the Celestial Selector. This integrates highly-multiplexed monolithic fibre systems (MFS) and switching networks of the type currently available in the telecommunications industry. It avoids bulky moving parts, whose limitations were noted in Paper I. In Paper III we will investigate the optimisation of such systems by varying the input-output mapping.

The application of photonics to astronomy offers major advantages in the area of highly-multiplexed spectroscopy, especially when applied to extremely large telescopes. These include the suppression of the near-infrared night-sky spectrum [J. Bland-Hawthorn et al, Opt. Express 12, 5902 (2004), S. G. Leon-Saval et al, Opt. Lett. 30, 2545 (2005)] and the miniaturisation of spectrographs so that they may integrated into the light-path of individual spatial samples [J. Bland-Hawthorn et al, Proc SPIE 6269, 62690N (2006)]. Efficient collection of light from the telescope requires multimode optical fibres and three-dimensional photonic devices. We propose ultrafast laser inscription (ULI) [R. R. Thomson et al, Opt. Express 15, 11691 (2007)] as the best technology to fabricate 3D photonic devices for astrophotonic applications.

We explore the use of remapping techniques to improve the efficiency of highly-multiplexed fibre systems for astronomical spectroscopy. This is particularly important for the implementation of Diverse Field Spectroscopy (DFS, described in Paper II) using highly-multiplexed monolithic fibre systems (MFS). Diverse Field Spectroscopy allows arbitrary distributions of target regions to be addressed to optimise observing efficiency when observing complex, clumpy structures such as protoclusters which will be increasingly accessible to Extremely Large Telescopes (ELTS). We show how the adoption of various types of remapping between the input and output of a Monolithic Fibre Systems can allow contiguous regions of spatial elements to be selected using only simple switch arrays. Finally we show how this compares in efficiency with integral-field and multiobject spectroscopy by simulations using artificial and real catalogues of objects. With the adoption of these mapping strategies, DFS outperforms other techniques when addressing a range of realistic target distributions. These techniques are also applicable to bio-medical science and were in fact inspired by it.

We present results from cryogenic tests of Volume-Phase Holographic(VPH) gratings at 100 K. The aims of these tests are to see whether the diffraction efficiency as a function of wavelength is significantly different at a low temperature from that at room temperature and to see how the performance of a VPH grating is affected by a number of thermal cycles. We have completed 10 cycles between room temperature and 100 $K$, and find no clear evidence that the diffraction efficiency changes with temperature or with successive thermal cycle.

One of the highlights of the European ELT Science Case book is the study of resolved stellar populations, potentially out to the Virgo Cluster of galaxies. A European ELT would enable such studies in a wide range of unexplored distant environments, in terms of both galaxy morphology and metallicity. As part of a small study, a revised science case has been used to shape the conceptual design of a multi-object, multi-field spectrometer and imager (MOMSI). Here we present an overview of some key science drivers, and how to achieve these with elements such as multiplex, AO-correction, pick-off technology and spectral resolution.

We present a datacube covering the central 10 arcsec of the archetypal active galaxy NGC 1068 over a wavelength range 4200 to 5400 Angstrom. obtained during the commissioning of the integral field unit (IFU) of the Gemini Multiobject Spectrograph (GMOS) installed on the Gemini-North telescope. The datacube shows a complex emission line morphology in the [OIII] doublet and Hbeta line. To describe this structure phenomenologically we construct an atlas of velocity components derived from multiple Gaussian component fits to the emission lines. The atlas contains many features which cannot be readily associated with distinct physical structures. While some components are likely to be associated with the expected biconical outflow, others are suggestive of high velocity flows or disk-like structures. As a first step towards interpretation, we seek to identify the stellar disk using kinematical maps derived from the Mgb absorption line feature at 5170 Angstrom and make associations between this and gaseous components in the atlas of emission line components.

In this paper, we report measurements of diffraction efficiency and angular dispersion for a large format (~ 25 cm diameter) Volume-Phase Holographic (VPH) grating optimized for near-infrared wavelengths (0.9 -- 1.8 micron). The aim of this experiment is to see whether optical characteristics vary significantly across the grating. We sampled three positions in the grating aperture with a separation of 5 cm between each. A 2 cm diameter beam is used to illuminate the grating. At each position, throughput and diffraction angle were measured at several wavelengths. It is found that whilst the relationship between diffraction angle and wavelength is nearly the same at the three positions, the throughputs vary by up to ~ 10% from position to position. We explore the origin of the throughput variation by comparing the data with predictions from coupled-wave analysis. We find that it can be explained by a combination of small variations over the grating aperture in gelatin depth and/or refractive index modulation amplitude, and amount of energy loss by internal absorption and/or surface reflection.

In this paper we present the three dimensional dynamics of the galaxy SDSS J101345.39+011613.66, selected for its unusually strong Balmer absorption lines (Wo(H-delta)=7.5A). Using the GMOS-South IFU in Nod & Shuffle mode we have mapped the continuum and optical absorption lines of this z=0.1055 field galaxy. This galaxy has a disturbed morphology, with a halo of diffuse material distributed asymmetrically toward the north. Using the [OII] emission line (Wo([OII])=4.1A) we find that the gas and hot OB stars are offset from the older stars in the system. The gas also has a spatially extended and elongated morphology with a velocity gradient of 100+/-20km/s across 6kpc in projection. Using the strong H-gamma and H-delta absorption lines we find that the A- stars are widely distributed across the system and are not centrally concentrated arguing that the A-star population has formed in molecular clouds outside the nucleus. By cross correlating the spectra from the datacube with an A-star template we find evidence that the A-star population has a 40km/s shear in the same direction as the gas. The disturbed morphology, strong colour gradients and strong H-delta and H-gamma absorption lines in SDSS J101345.39 argue that this is a recent tidal interaction/merger between a passive elliptical and star-forming galaxy. Although based on a single object, these results show that we can spatially resolve and constrain the dynamics of this short lived (yet important) phase of galaxy formation in which the evolutionary process take galaxies from star-forming to their quiescent end products.

The IMACS-IFU is an Integral Field Unit built for the IMACS spectrograph at the Magellan-I-Telescope at Las Campanas Observatory. It consists of two rectangular fields of 5 by 7 arcseconds, separated by roughly one arcminute. With a total number of 2000 spatial elements it is the second largest fiber-lenslet based IFU worldwide, working in a wavelength range between 400 and 900 nm. Due to the equally sized fields classical background subtraction, beam switching and shuffling are possible observation techniques. One particular design challenge was the single, half a metre long curved slit in combination with a non telecentric output. Besides the construction some preliminary results are described.

We present results from cryogenic tests of a Volume-Phase Holographic (VPH) grating at 200 K measured at near-infrared wavelengths. The aims of these tests were to see whether the diffraction efficiency and angular dispersion of a VPH grating are significantly different at a low temperature from those at a room temperature, and to see how many cooling and heating cycles the grating can withstand. We have completed 5 cycles between room temperature and 200 K, and find that the performance is nearly independent of temperature, at least over the temperature range which we are investigating. In future, we will not only try more cycles between these temperatures but also perform measurements at a much lower temperature (e.g., 80 K).

In this letter, we exploit the gravitational potential of the rich cluster A2218 as a magnifying glass. We demonstrate that the magnification due to the cluster allows us to observe distant background galaxies at a comparable level of detail to galaxies at z~0.1. Using the GMOS Integral Field Unit on Gemini North we observed the spatially-resolved [OII](3727) emission line spectrum for a lensed disk-galaxy at z=1.034. Using a detailed model for the cluster mass distribution, we are able to correct for the lensing by the cluster and reconstruct the source morphology. We find that the overall magnification is a factor of 4.92 +/- 0.15, and the rest-frame absolute I-band magnitude is M_{I}^{rest} = -22.4 +/- 0.2, where the error bars include conservative estimates of the uncertainty in the source-plane reconstruction. The inclination-corrected circular velocity is 206 +/- 18km/s. The galaxy lies very close to the mean Tully-Fisher relation of present-day spirals. Although our results are based on a single object, they demonstrate that gravitational lensing can be viably used to make detailed studies of the evolution of the structure of distant field galaxies.

g', r', and i' images obtained with the Gemini Multi-Object Spectrograph (GMOS) on Gemini North are used to investigate the metallicity and stellar content of the M31 dwarf spheroidal companion galaxy And V. Red giant branch (RGB) stars are traced out to radii in excess of 126 arcsec from the galaxy center, indicating that And V extends over a diameter approaching 1 kpc. The mean g'-i' color of the RGB does not change with radius. Based on the slope of the RGB in the (i', g'-i') color-magnitude diagram we conclude that [Fe/H] = -2.2 +/- 0.1. This metallicity is lower than earlier estimates, and places And V squarely on the relation between metallicity and integrated brightness defined by other dwarf spheroidal and dwarf elliptical galaxies. We also fail to find a statistically significant population of luminous asymptotic giant branch stars near the center of the galaxy.

The centre of NGC 4151 has been observed in the J-band with the SMIRFS integral field unit (IFU) on the UK Infrared Telescope. A map of [Fe II] emission is derived, and compared with the distributions of the optical narrow line region and radio jet. We conclude that, because the [Fe II] emission is associated more closely with the visible narrow-line region than with the radio jet, it arises mainly through photoionization of gas by collimated X-rays from the Seyfert nucleus. The velocity field and strength with respect to [Pa B] are found to be consistent with this argument. The performance of the IFU is considered briefly, and techniques for observation and data analysis are discussed.

The Gemini Multiobject Spectrograph (GMOS) installed on the Gemini-North telescope has a facility for integral field spectroscopy over the wavelength range 0.4-1.0um. GMOS is converted to this mode by the remote insertion of an integral field unit (IFU) into the beam in place of the masks used for multiobject spectroscopy. With the IFU deployed, integral field spectroscopy is available over a fully-filled contiguous field of 5 x 7 arcsec with a sampling of 0.2 arcsec. A separate field of half the area, but otherwise identical, is also provided to aid background subtraction. The IFU contains 1500 lenslet-coupled fibres and is the largest-format fibre-based IFU yet tested on the sky and the first facility of any type for integral field spectroscopy employed on an 8/10m telescope. We describe the IFU and present results from commissioning.

Integral-field spectroscopy is the most effective method of exploiting the superb image quality of the ESO-VLT, allowing complex astrophysical processes to be probed on the angular scales currently accessible only for imaging data, but with the addition of information in the spectral dimension. We discuss science drivers and requirements for multiple deployable integral fields for spectroscopy in the near-infrared. We then describe a fully modular instrument concept which can achieve such a capability over a 5-10' field with up to 32 deployable integral fields, each fully cryogenic with 1-2.5 micron coverage at a spectral resolution of ~3000, each with a 4" x 4" field of view sampled at 0.2"/pixel to take advantage of the best K-band seeing.

A new integral-field spectrograph, SAURON, is described. It is based on the Tiger principle, and uses a lenslet array. SAURON has a large field of view and high throughput, and allows simultaneous sky subtraction. Its design is optimized for studies of the stellar kinematics, gas kinematics, and line-strength distributions of nearby early-type galaxies. The instrument design and specifications are described, as well as the extensive analysis software which was developed to obtain fully calibrated spectra, and the associated kinematic and line-strength measurements. A companion paper reports on the first results obtained with SAURON on the William Herschel Telescope.

We describe a new system for multiple object spectroscopy and integral field spectroscopy at near-infrared wavelengths using optical fibers. Both modes of the SMIRFS instrument have been tested at the UK Infrared Telescope with the CGS4 infrared spectrograph. The modular system includes a common optical system to image the fiber slit onto the cold slit inside the CGS4 cryostat. The multiobject mode consists of 14 interchangeable fused silica or zirconium fluoride fibers each with a field of 4 arcsec. The integral field mode consists of 72 fused silica fibers coupled with a lenslet array to give a contiguous field of 6x4 arcsec with 0.6 arcsec sampling. We describe the performance of both modes. For the multiobject mode, the feasibility and desirability of using fluoride fibers to extend the wavelength range into the K-band is discussed. For the integral field mode, the performance is compared with theoretical expectation with particular attention to the effect of Focal Ratio Degradation in the fibers. These results demonstrate the feasibility of multiobject and integral field spectroscopy in the near-infrared using lenslet-coupled fiber systems. Although SMIRFS in an experimental system working with a spectrograph not designed for this purpose, the throughput and uniformity of response are good. SMIRFS points the way forward to systems with much larger numbers of elements.

Using the multislit LDSS-2 spectrograph on the {\it William Herschel Telescope} we have completed a redshift survey in the magnitude range $22.5<B< 24$ which has produced 73 redshifts representing a 73\% complete sample uniformly-selected from four deep fields at high Galactic latitude. The survey extends out to $z>1$ and includes the highest redshift galaxy ($z=1.108$) yet discovered in a field sample. The median redshift, $\zmed=0.46$, and form of the redshift distribution constitute compelling evidence against simple luminosity evolution as an explanation of the large excess of faint galaxies ($\simeq\times$2--4 no-evolution) seen in this magnitude range. Rather we identify the excess population as blue objects with $z\sim 0.4$ and $B$\, luminosities similar to local $L^*$ galaxies indicating a dramatic decrease in the density of such objects over the last Hubble time, confirming the trends found in brighter redshift surveys. We also find a marked absence of {\it very} low redshift galaxies ($z<$0.1) at faint limits, severely constraining any significant steepening of the local field galaxy luminosity function at low luminosities.